Search Results (375)

This study presents the development of Cu-doped NiMo/TiO₂ photoelectrocatalysts for simultaneous green hydrogen production and pharmaceutical pollutant removal under simulated solar irradiation. The catalysts were synthesized via wet impregnation (15 wt.% total metal loading with 0.6 wt.% Cu) and thermally treated at 400 °C and 900 °C to investigate structural transformations and catalytic performance. Comprehensive characterization (XRD, BET, SEM, XPS) revealed phase transitions, enhanced crystallinity, and redistribution of redox states upon Cu incorporation, particularly the formation of NiTiO₃ and an increase in oxygen vacancies. Crystallite sizes for anatase, rutile, and brookite ranged from 21 to 47 nm at NiMoCu400, while NiMoCu900 exhibited only the rutile phase with 55 nm crystallites. BET analysis showed a surface area of 44.4 m²·g⁻¹ for NiMoCu400, and electrochemical measurements confirmed its higher electrochemically active surface area (ECSA, 2.4 cm²), indicating enhanced surface accessibility. In contrast, NiMoCu900 exhibited a much lower BET surface area (1.4 m²·g⁻¹) and ECSA (1.4 cm²), consistent with its inferior photoelectrocatalytic performance. Compared to previously reported binary NiMo/TiO₂ systems, the ternary NiMoCu/TiO₂ catalysts demonstrated significantly improved hydrogen production activity and more efficient photoelectrochemical degradation of paracetamol. Specifically, NiMoCu400 showed an anodic peak current of 0.24 mA·cm⁻² for paracetamol oxidation, representing a 60% increase over NiMo400 and a cathodic current of −0.46 mA·cm⁻² at −0.1 V vs. RHE under illumination, nearly six times higher than the undoped counterpart (–0.08 mA·cm⁻²). Mott–Schottky analysis further revealed that NiMoCu400 retained n-type behavior, while NiMoCu900 exhibited an unusual inversion to p-type, likely due to Cu migration and rutile-phase-induced realignment of donor states. Despite its higher photosensitivity, NiMoCu900 showed negligible photocurrent, confirming that structural preservation and surface redox activity are critical for photoelectrochemical performance. This work provides mechanistic insight into Cu-mediated photoelectrocatalysis and identifies NiMoCu/TiO₂ as a promising bifunctional platform for integrated solar-driven water treatment and sustainable hydrogen production. Full article

The development of cost-effective and scalable air/oxygen electrode materials is crucial for the advancement of Zn–air batteries (ZABs). Porous carbon materials doped with heteroatoms have attracted considerable attention in energy and environmental fields because of their tunable nanoporosity and high electrical conductivity. In this work, we report the synthesis of a three-dimensional (3D) N and P co-doped porous carbon (PA@pDC-1000), derived from a conjugated polyaniline–phytic acid polymer. The cross-linked, rigid conjugated polymeric framework plays a crucial role in maintaining the integrity of micro- and mesoporous structures and promoting graphitization during carbonization. As a result, the material exhibits a hierarchical pore structure, a high specific surface area (1045 m² g⁻¹), and a large pore volume (1.02 cm³ g⁻¹). The 3D N, P co-doped PA@pDC-1000 catalyst delivers a half-wave potential of 0.80 V (vs. RHE) and demonstrates a higher current density compared to commercial Pt/C. A primary ZAB utilizing this material achieves an open-circuit voltage of 1.51 V and a peak power density of 217 mW cm⁻². This metal-free, self-templating presents a scalable route for the generating and producing of high-performance oxygen reduction reaction catalysts for ZABs. Full article

Rapid economic growth has led to an increase in the use of multilayer plastic packaging, which involves complex polymer compositions and hinders recycling. This study investigated the catalytic pyrolysis of plastic packaging waste in a 3000 cm³ semibatch reactor, aiming to optimize kerosene-like hydrocarbon production. The temperature (420–500 °C), N₂ flow rate (25–125 mL/min), and catalyst loading (5–20 wt.%) were examined individually and in combination with activated carbon and an Fe-doped dolomite (Fe/DM) catalyst. Central composite design (CCD) and response surface methodology (RSM) were used to identify the optimal conditions and synergistic effects. Pyrolysis product analysis involved simulation distillation gas chromatography (Sim-DGC), gas chromatography/mass spectrometry (GC/MS), and Fourier transform infrared (FT-IR) spectroscopy. The optimal conditions (440 °C, 50 mL/min N₂ flow, catalyst loading of 10 wt.% using a 5 wt.% Fe-doped dolomite-activated carbon 0.6:0.4 mass/molar ratio) yielded the highest pyrolysis oil (79.6 ± 0.35 wt.%) and kerosene-like fraction (22.3 ± 0.22 wt.%). The positive synergistic effect of Fe/DM and activated carbon (0.6:0.4) enhanced the catalytic activity, promoting long-chain polymer degradation into mid-range hydrocarbons, with secondary cracking yielding smaller hydrocarbons. The pore structure and acid sites of the catalyst improved the conversion of intermediate hydrocarbons into aliphatic compounds (C₅–C₁₅), increasing kerosene-like hydrocarbon production. Full article

As a renewable alternative to fossil fuels, the industrial production of biodiesel urgently requires the development of efficient and recyclable solid base catalysts. In this study, the physicochemical properties and catalytic performance differences between MgO/Na₂CO₃ and MgO/K₂CO₃ catalysts were systematically compared using soybean oil as the raw material. By regulating the calcination temperature (500–700 °C), alcohol-to-oil ratio (3:1–24:1), and metal carbonate loading (10–50%), combined with N₂ adsorption–desorption, CO₂-TPD, XRD, SEM-EDS, and cycling experiments, the regulatory mechanisms of the ionic radius differences between sodium and potassium on the catalyst structure and performance were revealed. The results showed that MgO/Na₂CO₃-600 °C achieved a FAME yield of 97.5% under optimal conditions, which was 1.7% higher than MgO/K₂CO₃-600 °C (95.8%); this was attributed to its higher specific surface area (148.6 m²/g vs. 126.3 m²/g), homogeneous mesoporous structure, and strong basic site density. In addition, the cycle stability of MgO/K₂CO₃ was significantly lower, retaining only 65.2% of the yield after five cycles, while that of MgO/Na₂CO₃ was 88.2%. This stability difference stems from the disparity in their solubility in the reaction system. K₂CO₃ has a higher solubility in methanol (3.25 g/100 g at 60 °C compared to 1.15 g/100 g for Na₂CO₃), which is also reflected in the ion leaching rate (27.7% for K⁺ versus 18.9% for Na⁺). This study confirms that Na⁺ incorporation into the MgO lattice can optimize the distribution of active sites. Although K⁺ surface enrichment can enhance structural stability, the higher leaching rate leads to a rapid decline in catalyst activity, providing a theoretical basis for balancing catalyst activity and durability in sustainable biodiesel production. Full article

The selective catalytic reduction of NO_x with CH₄ (CH₄-SCR) holds the potential to simultaneously abate harmful NO_x and CH₄ greenhouse gases. In this study, a series of bimetallic M-In/H-SSZ-39 catalysts (where M represents Cr, Co, Ce, and Fe) were prepared via an ion exchange method and subsequently evaluated for their CH₄-SCR activity. The influences of the preparation parameters, including the metal ion concentration and calcination temperature, as well as the operating conditions, such as the CH₄/NO ratio, O₂ concentration, water vapor content, and gas hourly space velocity (GHSV), on the catalytic activity of the optimal Cr-In/H-SSZ-39 catalyst were meticulously examined. The results revealed that the Cr-In/H-SSZ-39 catalyst exhibited peak CH₄-SCR catalytic performance when the Cr(NO₃)₃ concentration was 0.0075 M, the In(NO₃)₃ concentration was 0.066 M, and the calcination temperature was 500 °C. Under optimal operating conditions, namely GHSV of 10,000 h⁻¹, 400 ppm NO, 800 ppm CH₄, 15 vol% O₂, and 6 vol% H₂O, the NO_x conversion rate reached 93.4%. To shed light on the excellent performance of Cr-In/H-SSZ-39 under humid conditions, a comparative analysis of the crystalline phase, chemical composition, pore structure, surface chemical state, surface acidity, and redox properties of Cr-In/H-SSZ-39 and In/H-SSZ-39 was conducted. The characterization results indicated that the incorporation of Cr into In/H-SSZ-39 enhanced its acidity and also facilitated the generation of InO⁺ active species, which promoted the oxidation of NO and the activation of CH₄, respectively. A synergistic effect was observed between Cr and In species, which significantly improved the redox properties of the catalyst. Consequently, the activated CH₄ could further interact with InO⁺ to produce carbon-containing intermediates such as HCOO⁻, which ultimately reacted with nitrate-based intermediates to yield N₂, CO₂, and H₂O. Full article

The esterification of terephthalic acid (PTA) with methanol to dimethyl terephthalate (DMT) was investigated using commercially available zeolite catalysts as the eco-friendly solid acids. Six typical zeolites (ZSM-5-25, ZSM-5-50, ZSM-5-100, ZSM-35, MOR, and β) were systematically evaluated. Among them, β zeolite showed excellent catalytic performance, achieving nearly 100% PTA conversion and 76.1% DMT selectivity under the conditions of 200 °C, of 0.5 MPa N₂ pressure, m(PTA):V(methanol) of 1:40 (g/mL), m(PTA):m(catalyst) of 10:1 over 4 h. The characterization results show that the catalytic efficiency was correlated with acid site strength, specific surface area, and mesoporous structure of the zeolite. After optimization, β zeolite achieved 100% PTA conversion and 94.1% DMT selectivity under the conditions of 200 °C, of 1 MPa N₂ pressure, m(PTA)/V(methanol) of 1:30 (g/mL), m(PTA)/m(catalyst) of 8:1 over 8 h. Moreover, β zeolite exhibited superior stability, maintaining over 92% of its initial activity after five cycles, highlighting its potential for sustainable DMT production. Full article

In the “dual carbon” objective, the preparation of non-precious metal catalysts with low cost and high activity is essential for the study of hydrogen evolution reactions (HERs). This study employed biomass pomelo peel powder as the carbon source and ammonium metatungstate (AMT) as the tungsten source and, through a facile one-step method in molten salt, fabricated a biomass carbon-based nanocatalyst featuring carbon flakes adorned with tungsten carbide (WC) nanoparticles. Dicyandiamide and cysteine were introduced as nitrogen and sulfur sources, respectively, to explore the impacts of N-S elemental doping on the structure, composition, and HER performance of the WC/C catalyst. The experimental results showed that N-S doping changed the electronic structure of WC and increased the electrochemically active surface area, resulting in a significant increase in the HER activity of WC/C@N-S catalysts. The WC/C@N-S catalyst was evaluated with hydrogen evolution performance in a 0.5 mol/L H₂SO₄ solution. When the cathodic current density reached 10 mA/cm², the overpotential was 158 mV, and the Tafel slope was 68 mV/dec, underscoring its excellent HER performance. The outcomes offer novel insights into the high-value utilization of agricultural biomass resources, and pave the way for the development of cost-effective, innovative hydrogen evolution catalysts. Full article

Ammonia is a promising hydrogen storage material because it is easy to store and decompose into CO_X-free hydrogen. A Ru-based catalyst exhibits good catalytic performance in ammonia decomposition, and enhancing the interaction between the Ru atoms and the support is an important way to further improve its catalytic activity. In this study, CeO₂ was prepared by calcination using a cerium-based metal–organic framework (MOF) as the precursor, and the number of oxygen vacancies on the surface of CeO₂ was regulated by hydrogen reduction. The XPS and Raman results showed that abundant oxygen vacancies were formed on the surface of these CeO₂, and their number increased with an increase in the reduction time. The Ru/CeO₂-4 h catalyst, using CeO₂ reduced for 4 h as the support, exhibited good catalytic activity in ammonia decomposition, reaching 98.9% ammonia conversion and 39.74 mmol g_cat⁻¹ min⁻¹ hydrogen yield under the condition of GHSV = 36,000 mL g_cat⁻¹ h⁻¹ at 500 °C. The XAFS results demonstrated that Ru was stably anchored with oxygen vacancies on the surface of CeO₂ via Ru-O-Ce bonds. Density functional theory calculations further showed that these bondings lower the reaction energy barrier for N-H bond cleavage, thereby significantly enhancing the catalytic activity. Full article

Background/Objectives: Dental caries and candidiasis are major health problems worldwide. Dental caries is caused by cariogenic bacteria, especially those belonging to the Streptococcus genus, whereas candidiasis is caused by Candida species. In this study, the antimicrobial activity of a series of synthetic N-methyl-4-piperidone-derived monoketone curcuminoids (MKCs) against Candida albicans, C. krusei, and a representative panel of cariogenic bacteria was assessed. Methods: Fifteen MKCs were synthesized using an environmentally friendly base-catalyzed Claisen–Schmidt condensation between an aromatic aldehyde (R-PhCHO) and N-methyl-4-piperidone ethanol using NaOH as the catalyst. These compounds were evaluated for their antibacterial activity against a representative panel of cariogenic bacteria, along with their antifungal activity against Candida krusei and C. albicans. The antimicrobial activity was determined based on the Minimum Inhibitory Concentration (MIC) values. Results: Most of the compounds were obtained in about 2 h in yields ranging from 40 to 70%. None of the compounds displayed antifungal activity, even at 100 μg/mL, the highest tested concentration. Similarly, none of the compounds were active against Enterococcus faecalis. On the other hand, compounds 1 (R = H), 10 (R = 3,4,5-OMe), and 13 (R = 3-F) displayed moderate activity against Streptococcus mutans (13), S. salivarus (1), L. paracasei (1 and 10), S. mitis (1, 10, and 13), S. sanguinis (1, 10, and 13), and S. sobrinus (13), with MIC values of 250 μg/mL and 500 μg/mL. The presence of the N-methyl-4-piperidone ring was found to boost the antibacterial activity as compared to the corresponding acetone-derived MKCs. Moreover, the antibacterial activity of compounds 10 and 13 was associated with the presence and position of the fluor atom and the methoxy groups at the aromatic ring. Conclusions: This study contributed to a better understanding of the antimicrobial activity of MKCs, whose data in the literature are still scarce. Full article

Developing efficient and durable non-precious metal catalysts for oxygen electrocatalysis in fuel cells and zinc–air batteries remains an urgent issue to be addressed. Herein, a bimetallic CoCe-NC catalyst is synthesized through pyrolysis of Co/Ce co-doped metal–organic frameworks (MOFs), retaining the inherently high surface area of MOFs to maximize the exposure of Co-N and Ce-N active sites. The electronic interaction between Co and Ce atoms effectively modulates the adsorption/desorption behavior of oxygen-containing intermediates, thereby enhancing intrinsic catalytic activity. In alkaline media, the CoCe-NC catalyst exhibits E_1/2 = 0.854 V electrocatalytic capability comparable to commercial Pt/C, along with superior methanol resistance and durability. Notably, CoCe-NC demonstrates an overpotential 84 mV lower than Pt/C at 300 mA cm⁻² in a GDE half-cell. When the catalyst is employed as a cathode in zinc–air batteries, it demonstrates an open-circuit voltage of 1.47 V, a peak power density of 202 mW cm⁻², and exceptional cycling durability. Full article

Ru-based catalysts manifest unparalleled hydrogen evolution reaction (HER) performance, but the hydrolysis of Ru species and the accumulation of corresponding reaction intermediates greatly limit HER activity and stability. Herein, Ru nanoparticle assemblies modified with single Mo atoms and supported on N-incorporated graphene (referred to as MoRu-NG) are compounded via hydrothermal and chemical vapor deposition (CVD) methods. The incorporation of single Mo atoms into Ru lattices modifies the local atomic milieu around Ru centers, significantly improving HER catalytic behavior and stability. More specifically, MoRu-NG achieves overpotentials of 53 mV and 28 mV at 10 mA cm⁻², with exceptional stability in acidic and alkaline seawater solutions, respectively. In MoRu-NG, Ru atoms have a special electronic structure and thus possess optimal hydrogen adsorption energy, which indicates that excellent HER activity mainly hinges upon Ru centers. To be specific, the d-electron orbitals of Ru atoms are close to half full, giving Ru atoms moderate bond energy for the assimilation and release of hydrogen, which is beneficial for the conversion of reaction intermediates. Moreover, the incorporation of single Mo atoms facilitates the formation of O and O’-bidentate ligands, significantly enhancing the structural stability of MoRu-NG in universal-pH seawater electrolysis. This work advances a feasible construction method of hexagonal octahedral configuration (Ru-O-Mo-N-C) and provides a route to synthesize an efficient and stable catalyst for electrocatalytic HER in universal-pH seawater. Full article

In this study, a vanadyl phthalocyanine was synthesized and characterized using XRD, FTIR, and XPS, confirming the successful metalation of the phthalocyanine ring. XRD analysis showed the vanadyl phthalocyanine crystallized in the P-1 crystal lattice, with unit cell parameters a = 12.058 Å, b = 12.598 Å, and c = 8.719 Å, and the lattice angels were 96.203°, 94.941°, and 68.204°. FTIR spectroscopy supported the metalation by the disappearance of the N-H stretch of the non-metalated phthalocyanine. The vanadyl phthalocyanine was tested as a heterogenous catalyst for the conversion of fructose into methyl levulinate in H₂SO₄–methanol and HCl–methanol systems. The H₂SO₄–methanol reaction system catalyzed with the vanadyl phthalocyanine, and a zeroth-order rate constant of 1.10 × 10⁻⁶ M/s was observed, which was 1.74 times faster than sulfuric acid alone. The HCl–methanol system showed a zeroth-order of reaction with a rate constant of 2.33 × 10⁻⁶ M/s, which was 1.3 times faster than the HCl–methanol alone. While the HCl–methanol system showed a faster reaction rate, product distribution favored methyl levulinate formation in the H₂SO₄–methanol system. The main products identified were methyl levulinate and hepta-2,4-dienoic acid methyl ester, with a minor amount of hydroxymethylfurfural formed. These results suggest that vanadyl phthalocyanine can be effectively used as a catalyst to increase the rate of fructose conversion to methyl levulinate in either H₂SO₄ or HCl–methanol. Full article

The proton exchange membrane fuel cell (PEMFC) is a promising energy conversion technology. The synthesis route of the cathode oxygen reduction catalyst electrode is an important factor affecting the development of the battery. In traditional technology, Pt shows low utilization of oxygen reduction activity due to poor contact between catalyst nanoparticles (NP), the electrolyte, and oxygen. In this work, an effective electrochemical method for the preparation of a Pt/C catalyst electrode was proposed. The carbon paper (CP) substrate was electrochemically activated by HNO₃, and then, Pt nanoparticles were prepared on CP by one-step electrodeposition. Secondly, a Density Functional Theory (DFT) investigation was carried out to elucidate that the N-doped catalyst facilitates the desorption of intermediates from the catalyst surface and promotes the oxygen reduction reaction. Thirdly, the effects of acid activation voltage were discussed. The result shows that increasing the voltage significantly increases the concentration of C–N groups and decreases the particle size of Pt. The effects of acidification concentration were investigated at an optimal activation voltage of 1.6 V. When the activation concentration was 0.1 mol, Pt⁰ reached an optimal value, and therefore obtained an equilibrium between the adsorption of oxygen on Pt and the desorption of the intermediates. Pt/0.1CP_1.6 exhibits better performance than commercial catalysts in oxygen reduction reactions. After 5000 testing cycles, the catalyst showed a constant durability with only a 3.0 mV·dec⁻¹ increase of the Tafel slope and just a 6.7 m²·g_Pt⁻¹ decline of the ECSA. Full article

In this study we present an application of wood biomass—alder wood char—as the carbon precursor for the synthesis of novel and sustainable nitrogen-doped activated-carbon-supported nickel nanoparticle catalyst (AWC-Ni-N) for hydrazine oxidation. For comparison, the wood-based carbon material doped with nitrogen only (AWC-N) was also synthesized. Extensive characterization, including SEM, Raman spectroscopy, XPS, and XRD revealed the catalysts’ microstructure and properties. Electrochemical testing demonstrated that the AWC-Ni-N catalyst significantly enhanced the efficiency of the hydrazine oxidation reaction. In addition, direct N₂H₄-H₂O₂ single-fuel-cell tests were conducted using the prepared AWC-N and AWC-Ni-N catalysts as the anodes and cathodes. Peak power densities of up to 10.8 mW cm⁻² were achieved at 25 °C, corresponding to a current density of 27 mA cm⁻² and a cell voltage of 0.4 V when the AWC-Ni-N catalyst was used as both the anode and cathode. Furthermore, the peak power density increased by approximately 1.6 and 2.9 times, respectively, when the operating temperature was raised from 25 °C to 55 °C for the AWC-N and AWC-Ni-N catalysts. Overall, the AWC-N and AWC-Ni-N catalysts demonstrated significant potential as anode and cathode materials in direct N₂H₄-H₂O₂ fuel cells. Full article

Developing efficient bifunctional oxygen reduction (ORR) and oxygen evolution (OER) electrocatalysts is critical for renewable energy technologies. Noble metal catalysts face limitations in cost, scarcity, and bifunctional compatibility. Herein, we report the synthesis of nickel nanoparticles encapsulated in nitrogen-doped carbon nanosheets (Ni@NC-T) via a solvothermal polymerization and pyrolysis process using a Ni-hexamine coordination framework (NiHMT) as a precursor. The Ni@NC-900 catalyst exhibits superior ORR and OER activity under alkaline conditions, with an ORR performance (half-wave potential = 0.86 V) comparable to commercial Pt/C and an OER overpotential of only 430 mV at 10 mA cm⁻². Structural analysis indicates that the hierarchical porous structure and high specific surface area (409 m² g⁻¹) of Ni@NC-900 facilitate the exposure of active sites and enhance mass transport. The surface-doped nitrogen species, predominantly in the form of pyridinic N and graphitic N, promote electron transfer during the ORR. Furthermore, its application as a bifunctional cathode in rechargeable zinc-air batteries results in a high power density of 137 mW cm⁻², surpassing the performance levels of many existing carbon-based bifunctional catalysts. This work highlights a facile strategy for the fabrication of transition metal-based catalysts encapsulated in MOF-derived carbon matrices, with promising potential for energy storage and conversion devices. Full article