Search Results (3,870)

The high cost of hydrogen production is the primary factor limiting the development of the hydrogen energy industry chain. Additionally, due to the inefficiency of hydrogen production by water electrolysis technology, the development of high-performance catalysts is an effective means of producing low-cost hydrogen. In water electrolysis technology, the electrocatalytic activity of the electrode affects the kinetics of the oxygen evolution reaction (OER) and the hydrogen evolution rate. This study utilizes the liquid phase co-precipitation method to synthesize three types of Prussian blue analog (PBA) electrocatalytic materials: Fe/PBA(Fe₄[Fe(CN)₆]₃), Fe-Mn/PBA((Fe, Mn)₃[Fe(CN)₆]₂·nH₂O), and Fe-Mn-Co/PBA((Mn, Co, Fe)₃^II[Fe^III(CN)₆]₂·nH₂O). X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses show that Fe-Mn-Co/PBA has a smaller particle size and higher crystallinity, and its grain boundary defects provide more active sites for electrochemical reactions. The electrochemical test shows that Fe-Mn-Co/PBA exhibits the best electrochemical performance. The overpotential of the oxygen evolution reaction (OER) under 1 M alkaline electrolyte at 10/50 mA·cm⁻² is 270/350 mV, with a Tafel slope of 48 mV·dec⁻¹, and stable electrocatalytic activity is maintained at 5 mA·cm⁻². All of these are attributed to the synergistic effect of Fe, Mn, and Co metal ions, grain refinement, and the generation of grain boundary defects and internal stresses. Full article

As an efficient clean energy technology, water electrolysis for hydrogen production has its efficiency limited by the sluggish oxygen evolution reaction (OER) kinetics, which drives the demand for the development of high-performance anode OER catalysts. This work constructs bimetallic (Al, Mn) co-doped nanoporous spinel CoFe₂O₄ (np-CFO) with a tunable structure and composition as an OER catalyst through a simple two-step dealloying strategy. The as-formed np-CFO (Al and Mn) features a hierarchical flaky configuration; that is, there are a large number of fine nanosheets attached to the surface of a regular micron-sized flake, which not only increases the number of active sites but also enhances mass transport efficiency. Consequently, the optimized catalyst exhibits a low OER overpotential of only 320 mV at a current density of 10 mA cm⁻², a minimal Tafel slope of 45.09 mV dec⁻¹, and exceptional durability. Even under industrial conditions (6 M KOH, 60 °C), it only needs 1.83 V to achieve a current density of 500 mA cm⁻² and can maintain good stability for approximately 100 h at this high current density. Theoretical simulations indicate that Al and Mn co-doping could indeed optimize the electronic structure of CFO and thus decrease the energy barrier of OER to 1.35 eV. This work offers a practical approach towards synthesizing efficient and stable OER catalysts. Full article

The usage of fossil fuels has resulted in increasingly severe environmental problems, such as climate change, air pollution, water pollution, etc. Hydrogen energy is considered one of the most promising clean energies to replace fossil fuels due to its pollution-free and high-heat properties. However, the oxygen evolution reaction (OER) remains a critical challenge due to its high overpotential and slow kinetics during water electrolysis for hydrogen production. Electrocatalysts play an important role in lowering the overpotential of OER and promoting the kinetics. Co₃O₄-based electrocatalysts have emerged as promising candidates for the oxygen evolution reaction (OER) due to their favorable catalytic activity and good compatibility compared with precious metal-based electrocatalysts. This review presents a summary of the recent developments in the synthesis strategies and mechanisms of Co₃O₄-based electrocatalysts for the OER. Various synthesis strategies have been explored to control the size, morphology, and composition of Co₃O₄ nanoparticles. These strategies enable the fabrication of well-defined nanostructures with enhanced catalytic performance. Additionally, the mechanisms of OER catalysis on Co₃O₄-based electrocatalysts have been elucidated. Coordinatively unsaturated sites, synergistic effects with other elements, surface restructuring, and pH dependency have been identified as crucial factors influencing the catalytic activity. The understanding of these mechanisms provides insights into the design and optimization of Co₃O₄-based electrocatalysts for efficient OER applications. The recent advancements discussed in this review offer valuable perspectives for researchers working on the development of electrocatalysts for the OER, with the goal of achieving sustainable and efficient energy conversion and storage systems. Full article

To investigate temporal deformation mechanisms of hydraulic asphalt concrete slope flow under evolving temperatures, this study developed a novel temperature-controlled slope flow intelligent test apparatus. Using this apparatus, slope flow tests were conducted at four temperature levels: 20 °C, 35 °C, 50 °C, and 70 °C. By applying nonlinear dynamics theory, the temporal evolution of slope flow deformation and its nonlinear mechanical characteristics under varying temperatures were thoroughly analyzed. Results indicate that the thermal stability of hydraulic asphalt concrete is synergistically governed by the phase-transition behavior between asphalt binder and aggregates. Temporal evolution of slope flow exhibits a distinct three-stage pattern as follows: rapid growth (0~12 h), where sharp temperature rise disrupts the primary skeleton of coarse aggregates; decelerated growth (12~24 h), where an embryonic secondary skeleton forms and progressively resists deformation; stabilization (>24 h), where reorganization of coarse aggregates is completed, establishing structural equilibrium. The thermal stability temperature influence factor (δ) shows a nonlinear concave growth trend with increasing test temperature. Dynamically, this process transitions sequentially through critical stability, nonlinear stability, period-doubling oscillatory stability, and unsteady states. Full article

Anion exchange membrane (AEM) water electrolysis is a potentially inexpensive and efficient source of hydrogen production as it uses effective low-cost catalysts. The catalytic activity and performance of nickel iron oxide (NiFeO_x) catalysts for hydrogen production in AEM water electrolyzers were investigated. The NiFeO_x catalysts were synthesized with various iron content weight percentages, and at the stoichiometric ratio for nickel ferrite (NiFe₂O₄). The catalytic activity of NiFeO_x catalyst was evaluated by linear sweep voltammetry (LSV) and chronoamperometry for the oxygen evolution reaction (OER). NiFe₂O₄ showed the highest activity for the OER in a three-electrode system, with 320 mA cm⁻² at 2 V in 1 M KOH solution. NiFe₂O₄ displayed strong stability over a 600 h period at 50 mA cm⁻² in a three-electrode setup, with a degradation rate of 15 μV/h. In single-cell electrolysis using a X-37 T membrane, at 2.2 V in 1 M KOH, the NiFe₂O₄ catalyst had the highest activity of 1100 mA cm⁻² at 45 °C, which increased with the temperature to 1503 mA cm⁻² at 55 °C. The performance of various membranes was examined, and the highest performance of the tested membranes was determined to be that of the Fumatech FAA-3-50 and FAS-50 membranes, implying that membrane performance is strongly correlated with membrane conductivity. The obtained Nyquist plots and equivalent circuit analysis were used to determine cell resistances. It was found that ohmic resistance decreases with an increase in temperature from 45 °C to 55 °C, implying the positive effect of temperature on AEM electrolysis. The FAA-3-50 and FAS-50 membranes were determined to have lower activation and ohmic resistances, indicative of higher conductivity and faster membrane charge transfer. NiFe₂O₄ in an AEM water electrolyzer displayed strong stability, with a voltage degradation rate of 0.833 mV/h over the 12 h durability test. Full article

Gypsum (CaSO₄·2H₂O) crystallization underpins numerous industrial processes, yet its response to chemical admixtures remains incompletely understood. This study investigates diffusion-controlled crystal growth in a coaxial test tube system to evaluate how three Sika^® ViscoCrete^® superplasticizers—430P, 111P, and 120P—affect nucleation, growth kinetics, morphology, and thermal behavior. The superplasticizers, selected for their surface-active properties, were hypothesized to influence crystallization via interfacial interactions. Ion diffusion was maintained quasi-steadily for 12 weeks, with crystal evolution tracked weekly by macro-photography; scanning electron microscopy and thermogravimetric/differential scanning were performed at the final stage. All admixtures delayed nucleation in a concentration-dependent manner. Lower dosages (0.5–1.0 wt%) yielded platy-to-prismatic morphologies and higher dehydration enthalpies, indicating more ordered lattice formation. In contrast, higher dosages (1.5–2.0 wt%) produced denser, irregular crystals and shifted dehydration to lower temperatures, suggesting structural defects or increased hydration. Among the additives, 120P showed the strongest inhibitory effect, while 111P at 0.5 wt% resulted in the most uniform crystals. These results demonstrate that ViscoCrete^® superplasticizers can modulate gypsum crystallization and thermal properties. Full article

New theologies developed in tandem with evolutionary biology during the nineteenth century, which have been called metaphysical evolutionisms and evolutionary theologies. A subset of these theologies analyzed here were developed by thinkers who accepted biological science but rejected both biblical creationism and materialist science. Tools from the cognitive science of religion, including conceptual metaphor theory (CMT) and blending theory, also known as conceptual integration theory (CIT), can help to explain the development of these systems and their transformation between the nineteenth and the twentieth centuries. The analysis focuses on several stable and popular blends of ideas, which have continued with some alteration into the twenty-first century. The three blends evaluated here are Progressive Soul Evolution, Salvation is Evolution, and Evolution is Therapy. Major contributors to these blends are the theosophist and theologian Helena P. Blavatsky and psychologist Frederic W. H. Myers, both influenced by the spiritualist movement, particularly the ideas of the spiritualist and biologist Alfred Russel Wallace. The influence of these blends can be seen in the twentieth-century “Aquarian Frontier,” a group of 145 thinkers and organizations identified in 1975 by counterculture historian Theodore Roszak. Part of the appeal of these blends may be seen in their use of metaphors, including the Great Chain of Being and A Purposeful Life is a Journey. The application of the polysemic term evolution in a sense that does much of the theological work of salvation in Christianity can in part be explained by applying the principles of blending theory, including the vital relation “achieve a human scale,” as well as compressions of time and identity. These blends have been successful because they meet the needs of a population who are friendly towards science but disenchanted with traditional religions. The blends provide a satisfying new theology that extends beyond death for a subset of adherents, particularly in the New Age and spiritual but not religious (SBNR) movements, who combine the agency of self-directed “evolution” with the religious concepts of grace and transcendence. Full article

PSR B1259-63/LS 2883 is a well-studied gamma-ray binary hosting a pulsar in a 3.4-year eccentric orbit around a Be-type star. Its non-thermal emission spans from radio to TeV energies, exhibiting a significant increase near the periastron passage. This paper is dedicated to the analysis of INTEGRAL observations of the system following its last periastron passage in June 2024. We aim to study the spectral evolution of this gamma-ray binary in the soft (0.3–10 keV) and hard (30–300 keV) X-ray energy bands. We performed a joint analysis of the data taken by INTEGRAL/ISGRI in July–August 2024 and quasi-simultaneous Swift/XRT observations. The spectrum of the system in the 0.3–300 keV band is well described by an absorbed power law with a photon index of $\Gamma =1.42\pm 0.03$. We place constraints on potential spectral curvature, limiting the break energy $E_{\mathrm{b}}>30$ keV for $\Delta \Gamma >0.3$ and cutoff energy $E_{\mathrm{cutoff}}>150$ keV at a 95% confidence level. For one-zone leptonic emission models, these values correspond to electron distribution spectral parameters of $E_{\mathrm{b},\mathrm{e}}>0.8$ TeV and $E_{\mathrm{cutoff},\mathrm{e}}>1.7$ TeV, consistent with previous constraints derived by H.E.S.S. Full article

Protein-losing nephropathy (PLN) involves a heterogeneous group of pathologies leading to selective glomerular damage and development of renal disease. ICGN, the main cause of PLN, requires immunosuppressive treatment. However, the scientific evidence in veterinary medicine on immunosuppressive therapeutic schemes in this condition is limited. The aim of this study is to describe the clinical and paraclinical evolution of five dogs with PLN, presumably associated with ICGN, treated with chlorambucil as immunosuppressive monotherapy. Suspected IGCN was established by the presence of a urine protein–creatinine ratio (UPC) ≥ 3 without response to standard therapy, hypoalbuminemia < 2, or progressive azotemia. Patients were treated with a dosage range of chlorambucil from 0.16 to 0.4 mg/kg (mean 0.25 mg/kg) every 24 h as the sole immunosuppressant. In the end, 4/5 patients showed significant clinical improvement, 3/3 had resolution of the nephrotic syndrome, 5/5 had a sustained decrease in UPC values during follow-up and no relevant adverse effects were observed. In this report, chlorambucil proved to be a well-tolerated and potentially effective monotherapy for immune-mediated PLN in dogs. Full article

In this study, the atmospheric corrosion behavior of AZ31 magnesium alloy exposed in Sanya and Nansha for one year was investigated. While existing studies have characterized marine corrosion of magnesium alloys, the synergistic corrosion mechanisms under extreme tropical marine conditions (simultaneous high Cl⁻, rainfall, and temperature fluctuations) remain poorly understood—particularly regarding dynamic corrosion–product evolution. The corrosion characteristics and behavior of AZ31 magnesium alloy exposed in Sanya and Nansha were evaluated using X-ray photoelectron spectroscopy, X-ray diffraction, electrochemical measurements, scanning electron microscopy, and weight loss tests. The results showed that the main components of corrosion products were MgCO₃·xH₂O(x = 3, 5), Mg₅(CO₃)₄(OH)₂·4H₂O, Mg₂Cl(OH)₃·4H₂O, and Mg(OH)₂. The corrosion rate exposed in the Nansha was 26.5 μm·y⁻¹, which was almost two times than that in Sanya. Localized corrosion is the typical corrosion characteristic of AZ31 magnesium alloy in this tropical marine atmosphere. This study exposes the dynamic crack–regeneration mechanism of corrosion products under high-Cl⁻-rainfall synergy. The corrosion types of AZ31 magnesium alloy in this tropical marine atmosphere were mainly represented by pitting corrosion and filamentous corrosion. Full article

Hydrogen energy is a pivotal carrier for achieving carbon neutrality, requiring green and efficient production via water electrolysis. However, the anodic oxygen evolution reaction (OER) involves a sluggish four-electron transfer process, resulting in high overpotentials, while the prohibitive cost and complex preparation of precious metal catalysts impede large-scale commercialization. In this study, we develop a FeCo-based bimetallic deep eutectic solvent (FeCo-DES) as a multifunctional reaction medium for engineering a three-dimensional (3D) coral-like FeOOH-Co₂(OH)₃Cl/NF composite via a mild one-step impregnation approach (70 °C, ambient pressure). The FeCo-DES simultaneously serves as the solvent, metal source, and redox agent, driving the controlled in situ assembly of FeOOH-Co₂(OH)₃Cl hybrids on Ni(OH)₂/NiOOH-coated nickel foam (NF). This hierarchical architecture induces synergistic enhancement through geometric structural effects combined with multi-component electronic interactions. Consequently, the FeOOH-Co₂(OH)₃Cl/NF catalyst achieves a remarkably low overpotential of 197 mV at 100 mA cm⁻² and a Tafel slope of 65.9 mV dec⁻¹, along with 98% current retention over 24 h chronopotentiometry. This study pioneers a DES-mediated strategy for designing robust composite catalysts, establishing a scalable blueprint for high-performance and low-cost OER systems. Full article

The removal of antibiotics from aqueous media along with their recovery is still an open research topic, due to their practical and economical importance. Adsorption allows these two objectives to be achieved, provided that the adsorbent used is chemically and mechanically stable and has a low preparation cost. In this study, PET (polyethylene terephthalate) fibers, obtained by mechanically processing PET waste, were used for the adsorption of rifampicin (RIF) and rifaximin (RIX) antibiotics from aqueous media. The experimental adsorption capacity of PET fibers for the two antibiotics (RIF and RIX) was determined at different pH values (2.0–6.5), adsorbent dose (0.4–20.0 g/L), contact time (5–1440 min), initial antibiotic concentration (4.0–67.0 mg/L), and temperature (10, 22, and 50 °C); the experimental values of these parameters were analyzed using a neuro-evolutive technique (ANE) combining sequential deep learning (DL) models with a differential evolution algorithm. The obtained optimal ANN-DL algorithm was then used to obtain the optimal models for the adsorption of RIF and RIX on PET fibers, which should adequately describe the adsorption dynamics for both antibiotics. The adsorption processes are spontaneous and endothermic (ΔG < 0, ΔH > 0) and are described by the Langmuir model (R² > 0.97) and the pseudo-second order kinetic model (R² > 0.99). The retention of RIF and RIX on the surface of PET fibers occurs through physicochemical interactions, and the FTIR spectra and microscopic images support this hypothesis. The presence of inorganic anions in the aqueous solution leads to an increase in the adsorption capacities of RIF (max. 7.6 mg/g) and RIX (max. 3.6 mg/g) on PET fibers, which is mainly due to the ordering of water molecules in the solution. The experimental results presented in this study allowed for the development of the adsorption mechanism of RIF and RIX on PET fibers, highlighting the potential practical applications of these adsorption processes. Full article

In the traditional classification system of the Lauraceae family based on morphology and anatomy, the phylogenetic position of the genus Sassafras has long been controversial. Chloroplast (cp) evolution of Sassafras has not yet been illuminated. In this study, we first sequenced and assembled the complete cp genomes of Sassafras, and conducted the comparative cp genomics, phylogenomics, and divergence time estimation of this ecological and economic important genus. The whole length of cp genomes of the 10 Sassafras ranged from 151,970 bp to 154,011 bp with typical quadripartite structure, conserved gene arrangements and contents. Variations in length of cp were observed in the inverted repeat regions (IRs) and a relatively high usage frequency of codons ending with T/A was detected. Four hypervariable intergenic regions (ccsA-ndhD, trnH-psbA, rps15-ycf1, and petA-psbJ) and 672 cp microsatellites were identified for Sassafras. Phylogenetic analysis based on 106 cp genomes from 30 genera within the Lauraceae family demonstrated that Sassafras constituted a monophyletic clade and grouped a sister branch with the Cinnamomum sect. Camphora within the tribe Cinnamomeae. Divergence time between S. albidum and its East Asian siblings was estimated at the Middle Miocene (16.98 Mya), S. tzumu diverged from S. randaiense at the Pleistocene epoch (3.63 Mya). Combined with fossil evidence, our results further revealed the crucial role of the Bering Land Bridge and glacial refugia in the speciation and differentiation of Sassafras. Overall, our study clarified the evolution pattern of Sassafras cp genomes and elucidated the phylogenetic position and divergence time framework of Sassafras. Full article

This study investigated the effects of six cap management protocols targeting contrasting oxidation-reduction potential (ORP) evolutions during alcoholic fermentation of Pinot noir wines. Treatments included twice-daily punch-downs (PD) and pump-overs (PO), 1 h air or N₂ injections (AirMix, N₂Mix), air injections triggered by ORP ≤ −40 mV (RedoxConAir), and equal N₂ injections concurrent to RedoxConAir wines (RedoxConN₂). AirMix wines maintained ORP values above 0 mV throughout fermentation, showed an oxidatively favored glutathione-to-glutathione disulfide ratio (GSH:GSSG) of 0.3:1, and had 21% lower total phenolics and 24% lower anthocyanins than PD wines. In contrast, N₂Mix wines maintained the lowest ORP, near −100 mV, and showed a reductively favored GSH:GSSG ratio (7:1). PD wines extracted 48% more flavan-3-ols than PO wines, consistent with greater berry integrity disruption and seed submersion. Volatile composition was also impacted: ethyl n-octanoate showed the highest OAV among esters, ranging from 147 in PO wines to 116 in AirMix wines. Results suggest the GSH:GSSG ratio served as an indicator of redox history, with potential implications for color and aroma preservation during aging. Inert gas mixings resulted in equal or greater total phenolic content, while excessive air injections may provide a tool to soften astringency. Full article

In this work, the synthesis and structural characterization of the smallest possible member of the family of bis-functionalized {MnMo₆O₂₄} Anderson–Evans polyoxometalates (POMs) is reported. The synthesis of the title compound TBA₃{[HC(CH₂O)₃]₂MnMo₆O₁₈} (1) was accomplished by using trimethylolmethane as the capping unit (TBA: tetra(n-butyl)ammonium, n-B_u4N⁺). The molecular structure of the organic–inorganic POM gave rise to yet undisclosed ¹H-NMR features, which are discussed thoroughly. Single-crystal X-ray diffraction (XRD) analysis revealed a highly regular 3D packing of the polyoxoanions within a matrix of TBA cations. The hybrid POM is of particular interest regarding potential applications in photocatalysis (i.e., hydrogen evolution) and energy storage. Thus, the electrochemical and thermal properties of 1 are also analyzed. Full article