Search Results (4,234)

This article focuses on the fire safety risks associated with conventional glass–aluminum façades—with a particular focus on stick and unitized curtain walling systems—providing an overview of possible fire spread mechanisms, considering the role of the curtain wall in maintaining compartmentation at the spandrel zone. First, it analyzes some of the relevant requirements of different European building regulations. Then, it provides a test evidence-based critical analysis of the gaps and loopholes in the relevant fire resistance standard for partial curtain wall configurations (EN 1364-4), where the evaluation of the propagation within the façade system is not necessarily considered in the fire-resistant spandrel zone. Finally, it presents a proposal for addressing these gaps in the form of a theoretical concept for a new test configuration and additional assessment criteria. This is followed by an initial experimental analysis of the concept. The standard testing campaign showed that temperature rise in mullions can exceed 180 °C after 30 min if limiting measures are not considered in the façade design. However, this can be only detected if framing is in the non-exposed area of the sample, being part of the evaluation surface. Meanwhile, differences are detected between the results from standard and new assessment criteria in the new configuration proposed, including a more rapid temperature rise for framing elements (207 K in a second level mullion at minute 90) than for the common non-exposed assessment surface of the sample (172 K at the same time) in cases where cavities are not protected. Accordingly, the proposed configuration successfully detected vertical temperature transfer within mullions, which can remain undetected in standard EN 1364-4 tests, highlighting the potential for fire spread even in EI120-rated assemblies. Full article

The organization of consciousness is described through increasingly rich theoretical models. We review evidence that working memory capacity—essential to generating consciousness in the cerebral cortex—is supported by dual limbic memory systems. These dorsal (Papez) and ventral (Yakovlev) limbic networks provide the basis for mnemonic processing and prediction in the dorsal and ventral divisions of the human neocortex. Empirical evidence suggests that the dorsal limbic division is (i) regulated preferentially by excitatory feedforward control, (ii) consolidated by REM sleep, and (iii) controlled in waking by phasic arousal through lemnothalamic projections from the pontine brainstem reticular activating system. The ventral limbic division and striatum, (i) organizes the inhibitory neurophysiology of NREM to (ii) consolidate explicit memory in sleep, (iii) operating in waking cognition under the same inhibitory feedback control supported by collothalamic tonic activation from the midbrain. We propose that (i) these dual (excitatory and inhibitory) systems alternate in the stages of sleep, and (ii) in waking they must be balanced—at criticality—to optimize the active inference that generates conscious experiences. Optimal Bayesian belief updating rests on balanced feedforward (excitatory predictive) and feedback (inhibitory corrective) control biases that play the role of prior and likelihood (i.e., sensory) precision. Because the excitatory (E) phasic arousal and inhibitory (I) tonic activation systems that regulate these dual limbic divisions have distinct affective properties, varying levels of elation for phasic arousal (E) and anxiety for tonic activation (I), the dual control systems regulate sleep and consciousness in ways that are adaptively balanced—around the entropic nadir of E–I criticality—for optimal self-regulation of consciousness and psychological health. Because they are emotive as well as motive control systems, these dual systems have unique qualities of feeling that may be registered as subjective experience. Full article

The growing demand for natural and sustainable skincare products has driven interest in plant-based active ingredients, especially from in vitro cultures. This placebo-controlled study investigated the impact of a facial cream containing 2% Kickxia elatine (L.) Dumort cell suspension culture extract on various skin biophysical parameters. The cream was applied to the cheek once daily for six weeks on 40 healthy female volunteers between the ages of 40 to 49. The evaluated skin parameters including skin hydration, transepidermal water loss (TEWL), erythema intensity (EI), melanin intensity (MI), skin surface pH, and skin structure, wrinkle depth, vascular lesions, and vascular discolouration. The results indicated that significant improvements were observed in skin hydration (from 40.36 to 63.00 AU, p < 0.001) and there was a decrease in TEWL score (14.82 to 11.76 g/h/m², p < 0.001), while the skin surface pH was maintained (14.82 to 11.76 g/h/m², p < 0.001). Moreover, the K. elatine cell extract significantly improved skin structure values (9.23 to 8.50, p = 0.028), reduced vascular lesions (2.72 to 1.54 mm², p = 0.011), and lowered skin discolouration (20.98% to 14.84%, p < 0.001), indicating its moisturising, protective, brightening, and soothing properties. These findings support the potential use of K. elatine cell extract in dermocosmetic formulations targeting dry, sensitive, or ageing skin. Full article

Schizophrenia (SZ) is a complex neuropsychiatric disorder characterized by heterogeneous symptoms, relatively poor clinical outcome, and widespread disruptions in neural connectivity and oscillatory dynamics. This article attempts to review current evidence linking genomic and proteomic alterations with aberrant neural oscillations observed in SZ, including aberrations in all oscillatory frequency bands obtained via human EEG. The numerous genes discussed are mainly involved in modulating synaptic transmission, synaptic function, interneuron excitability, and excitation/inhibition balance, thereby influencing the generation and synchronization of neural oscillations at specific frequency bands (e.g., gamma frequency band) critical for different cognitive, emotional, and perceptual processes in humans. The review highlights how polygenic influences and gene–circuit interactions underlie the neural oscillatory and connectivity abnormalities central to SZ pathophysiology, providing a framework for future research on common genetic-neural function interactions and on potential therapeutic interventions targeting local and global network-level neural dysfunction in SZ patients. As will be discussed, many of these genes affecting neural oscillations in SZ also affect other neurological disorders, ranging from autism to epilepsy. In time, it is hoped that future research will show why the same genetic anomaly leads to one illness in one person and to another illness in a different person. Full article

Morphine is an opioid extracted from the poppy plant and highly effective for moderate to severe pain management. Development of techniques to measure the concentration of this highly addictive drug in various matrices is very important. This work was aimed at the development of a sensitive electrochemical method for detection of morphine in wastewater. Molecularly imprinted (MIP) electrodes were made by the electro-polymerization process using pyrrole as a monomer. Electro-polymerization was performed on glassy carbon electrodes in the presence of morphine before the extraction of the entrapped morphine molecules. Various techniques were employed to monitor the polymerization and response of the fabricated electrodes toward morphine. These techniques included Fourier transform infrared spectroscopy (FTIR), cyclic voltammetry (CV), square wave voltammetry (SWV), and electrochemical impedance spectroscopy (EIS). The morphine concentration was determined using SWV and CV by measuring the change in the redox peak current of [Fe(CN)₆]^−3/−4. These MIP electrode sensors were used to analyze morphine concentrations between 0 and 80.0 nM solution. The SWV showed a wider linear response region than CV. The detection limit using SWV was found to be 1.9 nM, while using CV, the detection limit was 2.75 nM. This MIP electrode sensor exhibited specificity when other closely related molecules were included and hence has potential as a cheap alternative technique for analysis of morphine. Full article

Background/Objectives: Papillary thyroid microcarcinoma (MPTC), a subset of papillary thyroid carcinoma (PTC), is increasingly detected with advanced imaging. While most MPTCs are indolent, some exhibit aggressive behavior, complicating clinical management. The BRAF V600E mutation, common in PTC, is linked to aggressive features, and its allele frequency (AF) may serve as a biomarker for tumor aggressiveness. This study explored the association between BRAF V600E AF and aggressive histopathological features in MPTC. Methods: Data from 1 January 2016 to 23 December 2023 were retrieved from two McGill University teaching hospitals. Inclusion criteria comprised patients aged ≥ 18 years with thyroid nodules ≤ 1 cm, documented BRAF V600E mutation and AF results, and available surgical pathology reports. Tumor aggressiveness was defined as the presence of lymph node metastasis, aggressive histological subtype (tall cell, hobnail, columnar, solid/trabecular or diffuse sclerosing), extra thyroidal extension, or extensive lymphovascular extension. Associations were explored using t-tests. Results: Among 1564 records, 34 met the inclusion criteria and were included in analyses. The mean BRAF V600E AF was significantly higher in aggressive tumors (23.58) compared to non-aggressive tumors (13.73) (95% CI: −18.53 to −1.16, p = 0.03). Although not statistically significant, trends were observed for higher BRAF V600E AF in tumors with lymph node metastasis (mean AF: 25.4) compared to those without (mean AF: 16.67, p = 0.08). No significant difference was noted in BRAF V600E AF by histological subtype (mean AF for aggressive: 19.57; non-aggressive: 19.15, p = 0.94). Conclusions: Elevated BRAF V600E AF is associated with aggressive behavior in MPTC, highlighting its potential as a biomarker to inform treatment strategies. Larger studies are warranted to validate these findings and enhance clinical management of MPTC patients. Full article

Anion exchange membrane (AEM) water electrolysis is a potentially inexpensive and efficient source of hydrogen production as it uses effective low-cost catalysts. The catalytic activity and performance of nickel iron oxide (NiFeO_x) catalysts for hydrogen production in AEM water electrolyzers were investigated. The NiFeO_x catalysts were synthesized with various iron content weight percentages, and at the stoichiometric ratio for nickel ferrite (NiFe₂O₄). The catalytic activity of NiFeO_x catalyst was evaluated by linear sweep voltammetry (LSV) and chronoamperometry for the oxygen evolution reaction (OER). NiFe₂O₄ showed the highest activity for the OER in a three-electrode system, with 320 mA cm⁻² at 2 V in 1 M KOH solution. NiFe₂O₄ displayed strong stability over a 600 h period at 50 mA cm⁻² in a three-electrode setup, with a degradation rate of 15 μV/h. In single-cell electrolysis using a X-37 T membrane, at 2.2 V in 1 M KOH, the NiFe₂O₄ catalyst had the highest activity of 1100 mA cm⁻² at 45 °C, which increased with the temperature to 1503 mA cm⁻² at 55 °C. The performance of various membranes was examined, and the highest performance of the tested membranes was determined to be that of the Fumatech FAA-3-50 and FAS-50 membranes, implying that membrane performance is strongly correlated with membrane conductivity. The obtained Nyquist plots and equivalent circuit analysis were used to determine cell resistances. It was found that ohmic resistance decreases with an increase in temperature from 45 °C to 55 °C, implying the positive effect of temperature on AEM electrolysis. The FAA-3-50 and FAS-50 membranes were determined to have lower activation and ohmic resistances, indicative of higher conductivity and faster membrane charge transfer. NiFe₂O₄ in an AEM water electrolyzer displayed strong stability, with a voltage degradation rate of 0.833 mV/h over the 12 h durability test. Full article

In crisis-stricken economies, leadership effectiveness increasingly hinges not on technical expertise alone but on emotional competence. While emotional intelligence (EI) has been widely acknowledged as a catalyst for effective leadership and employee outcomes, its role in volatile and resource-scarce contexts remains underexplored. This study addresses this critical gap by investigating the impact of five core EI dimensions, namely self-awareness, self-regulation, motivation, empathy, and social skills, on employee performance amid Lebanon’s ongoing multidimensional crisis. Drawing on Goleman’s EI framework and the Job Demands–Resources theory, the research employs a quantitative, cross-sectional design with data collected from 398 employees across sectors in Lebanon. Structural Equation Modeling revealed that all EI dimensions significantly and positively influenced employee performance, with self-regulation (β = 0.485) and empathy (β = 0.361) emerging as the most potent predictors. These findings underscore the value of emotionally intelligent leadership in fostering productivity, resilience, and team cohesion during organizational instability. This study contributes to the literature by contextualizing EI in an under-researched, crisis-affected setting, offering nuanced insights into which emotional competencies are most impactful during prolonged uncertainty. Practically, it positions EI as a strategic leadership asset for crisis management and sustainable human resource development in fragile economies. The results inform leadership training, policy design, and organizational strategies that aim to enhance employee performance through emotionally intelligent practices. Full article

This research focuses on designing polymer membranes as biocompatible materials using home-built electrospinning equipment, offering alternative solutions for tissue regeneration applications. This technological development supports cell growth on biomaterial substrates, including hepatocellular carcinoma (Hep-G2) cells. This work researches the compatibility of polymer membranes (fiber mats) made of polyvinylidene difluoride (PVDF) for possible use in cellular engineering. A standard culture medium was employed to support the proliferation of Hep-G2 cells under controlled conditions (37 °C, 4.8% CO₂, and 100% relative humidity). Subsequently, after the incubation period, electrochemical impedance spectroscopy (EIS) assays were conducted in a physiological environment to characterize the electrical cellular response, providing insights into the biocompatibility of the material. Scanning electron microscopy (SEM) was employed to evaluate cell adhesion, morphology, and growth on the PVDF polymer membranes. The results suggest that PVDF polymer membranes can be successfully produced through electrospinning technology, resulting in the formation of a dipole structure, including the possible presence of a polar β-phase, contributing to piezoelectric activity. EIS measurements, based on R_ct and C_dl values, are indicators of ion charge transfer and strong electrical interactions at the membrane interface. These findings suggest a favorable environment for cell proliferation, thereby enhancing cellular interactions at the fiber interface within the electrolyte. SEM observations displayed a consistent distribution of fibers with a distinctive spherical agglomeration on the entire PVDF surface. Finally, integrating piezoelectric properties into cell culture systems provides new opportunities for investigating the influence of electrical interactions on cellular behavior through electrochemical techniques. Based on the experimental results, this electrospun polymer demonstrates great potential as a promising candidate for next-generation biomaterials, with a probable application in tissue regeneration. Full article

Transonic/supersonic wind tunnels are indispensable equipment for advanced aircraft to operate across subsonic, transonic, and supersonic regimes. The deformation of the flexible nozzle is the key to accurately controlling the Mach number of transonic wind tunnels. However, solving the deformation of flexible wall plates remains challenging due to the highly nonlinear relationship between wall loading and deformation, as well as the lack of simple yet effective mathematical models under complex boundary conditions. To accurately describe the deformation of flexible wall plates and improve computational efficiency, this study systematically investigates the deformation characteristics of flexible walls in two orthogonal directions and proposes an orthogonal beam function (OBF) model for characterizing small-deflection deformations. For large-deflection deformations in a flexible wall, an elliptic integral (EI) solution is introduced, and the OBF model is correspondingly modified. Experimental validation confirms that the OBF model effectively describes large-deflection deformations in a flexible wall. This research contributes to solving large-deflection deformation in flexible wall plates, enhancing both computational efficiency and accuracy. Full article

Capacitive sensors are platforms that enable label-free, real-time detection at low non-perturbing voltages. These sensors do not rely on Faradaic processes, thereby eliminating the need for redox-active species and simplifying system integration for point-of-care diagnostics. However, their sensitivity in high-ionic-strength solutions, such as bodily fluids, is limited due to a reduced Debye length and non-specific interactions. The present review highlights advances in material integration, surface modification, and signal enhancement techniques to mitigate the challenges of deploying capacitive sensors in biofluids (sweat, saliva, blood, serum). This work further expands on the promise of such sensors for advancing liquid biopsies and highlights key technical challenges in translating capacitive systems to clinics. Full article

The role of emotional intelligence (EI) in the academic context has been steadily established, together with its impact on students’ academic achievement, well-being, and professional success. Therefore, this study examined the development of a key EI ability—emotional understanding—throughout secondary school and explored its impact on students’ academic achievement (maternal language and mathematics) at the end of this cycle, using the Vocabulary of Emotions Test. A total of 222 students were followed over the entire 3-year secondary cycle, using a three-wave longitudinal design spanning from 10th to 12th grade. At the first wave, participants were aged between 14 and 18 years (M = 15.4; SD = 0.63), with 58.6% being female. Overall, the results of Latent Growth Curve modeling indicated that students’ emotional understanding increased over the secondary school cycle. While student’s gender predicted the emotional understanding change patterns throughout secondary school, student’s GPA in 10th grade did not. Moreover, the initial levels of ability-based emotional understanding predicted students’ achievement in maternal language at the end of the cycle. Our findings offer valuable insights into how EI skills can contribute to academic endeavors in late adolescence and will explore their impact on educational settings. Full article

To address the low selectivity in the electrocatalytic conversion of furfural (FFR) to furfuryl alcohol (FFA) under alkaline conditions, a Zn-based metal–organic framework (MBON-2) featuring a 3D hierarchical flower-like architecture self-assembled from nanosheets was synthesized via a simple hydrothermal method. Under optimal conditions, MBON-2 exhibited an extremely high selectivity of FFA (100%) and a high Faradaic efficiency (FE) of 93.19% at −0.2 V vs. RHE. Electrochemical impedance spectroscopy (EIS) revealed the excellent electron transfer and mass transport properties of MBON-2. In addition, in situ Fourier transform infrared (FTIR) spectroscopy studies confirmed the adsorption of FFR molecules onto the Zn and B sites of MBON-2 during the ECH of FFR, providing key insights into the hydrogenation mechanism. The numerous exposed B and Zn sites of the MBON-2, as well as its robust structural stability contributed to its outstanding catalytic performance in the electrochemical hydrogenation (ECH) of FFR. This work provides valuable guidelines for developing efficient Zn-based catalysts for the ECH of FFR. Full article

The corrosion behavior of an additively manufactured Mg-1Zn alloy was investigated in both the transverse and longitudinal directions relative to the build direction, in the as-built condition and after annealing at 350 °C for 24 h under high vacuum. Microstructural characterization using XRD and SEM revealed the presence of magnesium oxide (MgO) and the absence of intermetallic second-phase particles. Optical microscopy (OM) images and Electron Backscatter Diffraction (EBSD) maps showed a highly complex grain morphology with anomalous, anisotropic shapes and a heterogeneous grain size distribution. The microstructure includes grains with a pronounced columnar morphology aligned along the build direction and is therefore characterized by a strong crystallographic texture. Electrochemical techniques, including PDP and EIS, along with gravimetric H₂ collection, concluded that the transverse plane exhibited greater corrosion resistance compared to the longitudinal plane. Additionally, an increase in cathodic kinetics was observed when comparing as-built with heat-treated samples. Full article

This study examines the contributions of renewable energy transition (RET) and environmental innovation (EI) to environmental performance in G7 countries from 2003 to 2021, with a focus on the transmission channels of green finance and environmental governance. Using the Augmented Mean Group (AMG) estimator and confirming robustness through the Dynamic Common Correlated Effects Mean Group (DCCE-MG) method, the study explores both direct and indirect effects of RET and EI on two key environmental indicators: the Environmental Performance Index and the Load Capacity Factor. The results reveal that both RET and EI have a significant impact on environmental performance. Moreover, green finance and environmental governance serve as crucial channels through which RET and EI exert their influence. These findings underscore the importance of developing effective financial instruments and robust regulatory frameworks to translate energy and innovation policies into tangible environmental benefits. By highlighting the interplay between technological advancement, financial capacity, and institutional quality, this study provides novel insights into the environmental policy landscape of advanced economies and offers guidance for designing integrated strategies to achieve long-term sustainability goals. Full article