Search Results (40)

AlCoCrFeNi high-entropy alloy coatings reinforced with different TiN contents (2 wt.%, 4 wt.%, and 6 wt.%) were fabricated on 304 stainless steel by laser cladding. The effects of TiN addition on the microstructure, hardness, friction behavior, and wear resistance of the coatings were investigated. Dry reciprocating sliding tests were conducted under a load of 10 N, a frequency of 5 Hz, a stroke length of 5 mm, and a duration of 20 min using GCr15 bearing steel balls as the counterpart. The results showed that the 2 wt.% TiN coating exhibited the best tribological performance within the investigated composition range, with a microhardness of 579.6 HV_0.5, a relatively low and stable friction coefficient of approximately 0.30–0.35, and a wear rate of 2.9 × 10⁻⁴ mm³/(N·m). When the TiN content increased to 4 wt.% and 6 wt.%, the wear resistance decreased, which was mainly associated with particle agglomeration, local stress concentration, and brittle spalling. These results indicate that appropriate TiN addition can improve the load-bearing capacity and wear resistance of laser-cladded AlCoCrFeNi coatings, providing a potential surface-strengthening strategy for 304 stainless steel components under dry sliding conditions. Full article

A surprising tribocatalytic capability has been discovered for Si single crystals to convert mechanical energy into chemical energy for organic dye degradation recently. In this study, their tribocatalytic capability has been explored for converting mechanical energy into chemical energy of water splitting. In glass reactors with Si single crystals coated on the bottoms and with H₂O and N₂ enclosed, Al₂O₃ nanoparticles, TiO₂ nanoparticles, and NiO particles were stimulated through magnetic stirring using home-made PTFE magnetic rotary disks separately. For Al₂O₃ nanoparticles, as much as 14,330 and 41,964 ppm H₂ were produced after 1 and 3 h of 400 rpm magnetic stirring, respectively, much higher than those obtained for TiO₂ and NiO, and for Al₂O₃ nanoparticles in glass-bottomed reactors as well. The tribocatalytic production of H₂ was further explored with respect to NaCl addition to H₂O and p/n doping in Si, with negative effects observed for them all. Photoluminescence spectroscopy revealed continuous generation of hydroxyl radicals in the course of magnetic stirring, which supports a tribocatalytic mechanism based on the excitation of electron–hole pairs in Si single crystals through mechanical energy absorbed through friction. These findings suggest a great potential for narrow-band semiconductors to utilize mechanical energy through friction to carry out important chemical reactions. Full article

Tool wear in CNC milling increases friction and torque demand at the tool-workpiece interface, which is reflected in spindle motor current. This study develops a non-intrusive tool wear condition classification method using spindle motor current monitoring during practical CNC milling of commercial medium-carbon steel workpieces (JIS S50C/AISI SAE 1050-equivalent; as-received and non-heat-treated; nominal laboratory hardness approximately 4.3 HRC). Experiments were performed on a Tongtai MDV-508 vertical machining center at fixed cutting conditions (3000 rpm spindle speed, 2 mm axial depth of cut, 5 mm cutting width, and 300 mm/min feed rate) using eight TiAlN-coated fine-grain WC–Co solid carbide end mills (10 mm diameter, four flutes; nominal Co binder approximately 10 wt%). An oil-based HS Highstart/HS-SSHS-BH10 cutting fluid was applied through the machine external coolant nozzle in flood mode at an estimated nominal flow rate of approximately 3 L/min and near-room coolant temperature (25 ± 2 °C), and was used as supplied without dilution. A clamp-type AC current sensor was installed on one phase line supplying the spindle motor, and current was acquired using an NI-9221 module at 20 kHz. Cutting intervals were isolated by envelope-based segmentation, concatenated, and divided into 1 s windows (0.5 s overlap) for feature extraction. Three feature sets were evaluated: time-domain statistics, frequency-domain statistics, and an FFT→PCA hybrid representation. Tool states (New, Mid-life, Old) were labeled using post-process surface roughness Ra thresholds supported by microscope observation. The PCA transformation was fitted only on training data and then applied to the held-out test data. A logistic regression classifier achieved 97.44% test accuracy (152/156 windows; 95% Wilson CI: 93.59–99.00%) with the PCA-hybrid features, outperforming time-domain (89.74%) and frequency-domain (94.87%) models. The results support spindle current monitoring as a low-cost approach for quality-aligned tool condition monitoring, while the external validity remains limited to the tested machine, material, tool, coolant, and cutting-parameter combination. Full article

Three Ni-based composite coatings with varying TiCN/h-BN contents were fabricated on the surface of Ti-6Al-4V (TC4) alloy by laser cladding. The coatings were formulated with a fixed 15% TiCN and 0%, 2% and 5% h-BN, corresponding to L1–L3 coatings. The microstructure and phase composition were fully characterized and investigated. In addition, the microhardness and wear resistance of the coating were evaluated too. The analysis revealed that the L1–L3 coatings primarily consisted of Ti, TiNi, Ti(C, N) and TiAl₃ phases. Microstructural analysis indicated that the top region of the coating was predominantly composed of granular crystals, while the middle and bonding regions featured a combination of dendrites and white granular crystals. The average microhardness values for the L1–L3 coatings were measured at 1203.8, 1216.8 and 1235.5 HV_0.2, respectively, while the corresponding wear volumes were 0.098, 0.094 and 0.086 mm³. As the h-BN content increased, the microstructure of the Ni-based composite coating became finer and finer. Some TiB particles were also generated in the coating, which made the average microhardness and wear resistance increase gradually. Notably, the coating with 5% h-BN demonstrated the highest average microhardness and optimal wear resistance. Compared with the substrate, 5% h-BN increased the wear resistance of the substrate by 47.6%. The primary wear mechanism observed was abrasive wear. Full article

WC-based cermet coatings with a CoCrNiAlTi binder were fabricated on 04Cr13Ni5Mo stainless steel substrates using the atmospheric high-velocity air–fuel (HVAF) spraying process. The influence of the air-to-fuel ratio (AFR) on the microstructure, mechanical properties, and wear resistance of the WC-CoCrNiAlTi coatings was systematically investigated. The results indicate that the WC-CoCrNiAlTi coatings primarily consisted of WC, (Co, Ni)₃W₃C and a face-centered cubic (FCC) binder phase. As the AFR increased, the formation of the (Co, Ni)₃W₃C phase gradually decreased. Concurrently, the coating density improved, which was attributed to the enhanced particle melting state and increased flight velocity, leading to better flattening upon impact. The average microhardness of the WC-CoCrNiAlTi coatings gradually increased with an increasing AFR. The coating produced at an AFR of 1.130 exhibited the highest microhardness of 1355.68 HV_0.2. Both the friction coefficient and the wear rate of the coatings decreased progressively as the AFR increased. At the optimal AFR of 1.130, the coating demonstrated the lowest friction coefficient (0.6435) and wear rate (1.15 × 10⁻⁶ mm³·N⁻¹·m⁻¹), indicating a wear resistance 34.85 times that of the stainless steel substrate. Furthermore, the slurry erosion weight loss rate of the WC-CoCrNiAlTi coatings decreased gradually with increasing AFR. The coating sprayed at an AFR of 1.130 showed the minimum erosion rate (1.70 × 10⁻⁶ g·cm⁻²·min⁻¹), which was 24.04 times lower than that of the substrate. The erosion mechanism of the WC-CoCrNiAlTi coatings was identified as the fatigue-induced removal of WC particles under alternating stress. The ductile high-entropy alloy (HEA) binder effectively protects the brittle WC phase through adaptive deformation, thereby significantly mitigating coating damage. Full article

To enhance the operational damage resistance of hydraulic machinery, this study employed laser cladding technology to fabricate a Co_37.4Cr₃₀Ni₂₀Al₅Ti₅Nb_2.6 high-entropy alloy coating on 04Cr13Ni5Mo substrate. The influence of laser power on the microstructure and properties of the coating was systematically investigated. Based on preliminary research, the friction-wear performance and cavitation erosion behavior of the coatings prepared at 3000 W, 3200 W, and 3400 W were specifically examined. Results indicate that as the laser power increased from 3000 W to 3400 W, the microhardness of the coating gradually decreased from 345.3 HV_0.2. At 3000 W, the precipitation of trace strengthening phases significantly enhanced the mechanical properties. In wear tests under a 20 N load for 30 min, the wear rate of the coating prepared at 3000 W was 1.41 × 10⁻⁴ mm³/(N·m), which is 13.5% lower than that of the 3200 W coating (1.63 × 10⁻⁴ mm³/(N·m)) and 16.07% higher in wear resistance compared to the substrate. Cavitation erosion tests revealed that after 20 h of ultrasonic vibration, the mass loss of the 3000 W coating was only 2.35 mg, representing an 88.89% reduction compared to the substrate (21.15 mg), and significantly lower than that of the 3200 W (4.57 mg) and 3400 W (3.85 mg) coatings. This study demonstrates that precise control of laser power can effectively optimize the cavitation erosion resistance of high-entropy alloy coatings, providing technical support for their application in harsh environments. Full article

This study focused on the measurement requirements of Digital Image Correlation (DIC) in high-temperature environments of aero-engines and systematically investigated the applicability and stability of high-temperature speckle materials. Five common coating materials (Ti, TiN, Ta, NiCr alloy, and SiC) were selected. Corresponding thin films were deposited on Al₂O₃ ceramic substrates using magnetron sputtering technology, and their surface color evolution from room temperature up to 1200 °C was examined. The film compositions were analyzed by Raman spectroscopy and X-ray photoelectron spectroscopy (XPS), revealing the mechanisms behind the color changes. The results indicate that Ti, TiN, Ta, and NiCr alloy exhibit significant color variations, which leads to insufficient color contrast for high-temperature speckle patterns. Further investigation shows that depositing an outer SiO₂ coating can improve surface scattering and reflection, while also inhibiting oxygen penetration, thereby enhancing oxidation resistance and improving speckle contrast. The SiC/SiO₂ composite structure demonstrates excellent thermal stability, making it an ideal speckle material for high-temperature DIC measurements. Full article

The sustainable production of energy without environmental footprints is a challenge of paramount importance to satisfy the ever-increasing global demand and to promote economic and social growth through a greener perspective. Such awareness has significantly stimulated worldwide efforts aimed at exploring various energy paths and sources, in compliance with the ever more stringent environmental regulations. Research advancements in these fields are directly dependent on the design, fabrication, and implementation of tailored multi-materials for efficient energy production and harvesting and storage devices. Herein, we aim at providing a survey on the ongoing research activities related to various aspects of functional materials for energy production, conversion, and storage. In particular, we present the opportunities and the main open challenges related to multifunctional materials spanning from carbon-based nanostructures for chemical energy conversion, ferroelectric ceramics for energy harvesting, and phase change materials for thermal energy storage to metallic materials for hydrogen technologies, heat exchangers for wind energy, and amphiphobic coatings for the protection of solar panels. The relevance of designing tailored materials for power generation is also presented. Finally, the importance of applying life cycle assessment to materials is emphasized through the case study of AlTiN thin films. Full article

The purpose of this study is to prepare new Fe_(21-x)CoNiCuAlTi_x alloy coatings and to investigate the phase composition, microstructure, wear resistance, and corrosion resistance of these high-entropy-alloy coatings with varying Ti content. High-entropy Fe_(21-x)CoNiCuAlTi_x (x = 0; 2; 4; 6; 8) alloy coatings were prepared on 65Mn steel substrates via laser cladding. The results showed that the addition of Ti promoted the formation of the BCC phase, which increased the hardness of the coatings and improved their wear resistance due to the hardening of the solid solution and grain refinement. The microhardness of the coating was 689.08HV_0.2 at x = 8, 2.056 times that of the base metal, and the wear resistance was 2.565 × 10⁻⁷ g/(N·m). The corrosion potential and corrosion current density were −0.199 V and 3.513 × 10⁻⁷ A/cm², respectively, indicating excellent corrosion resistance. The addition of titanium significantly enhanced the formation of the BCC phase, improved the microstructure through solid-solution hardening and grain refinement, and caused lattice distortion. These effects, as well as the formation of solid bonds, significantly improved the wear and corrosion resistance of the coatings. Full article

High-Power Impulse Magnetron Sputtering (HiPIMS) has emerged as an excellent technology for producing high-quality nitride coatings, such as aluminum nitride (AlN), titanium nitride (TiN), chromium nitride (CrN), and silicon nitride (SiN), and composite nitride coatings such as titanium aluminum nitride (TiAlN), TiAlNiCN, etc. These coatings are known for their exceptional hardness, thermal stability, and corrosion resistance. These make them ideal for high-performance applications. HiPIMS distinguishes itself by generating highly ionized plasmas that facilitate intense ion bombardment, leading to nitride films with superior mechanical strength, durability, and enhanced thermal properties compared to traditional deposition techniques. Critical HiPIMS parameters, including pulse duration, substrate bias, and ion energy, are analyzed for their influence on enhancing coating density, adhesion, and hardness. The review contrasts HiPIMS with other deposition methods, highlighting its unique ability to create dense, uniform coatings with improved microstructures. While HiPIMS offers substantial benefits, it also poses challenges in scalability and process control. This review addresses these challenges and discusses hybrid, bipolar, and synchronized HiPIMS solutions designed to optimize nitride coating processes. Hybrid HiPIMS, for instance, combines HiPIMS with other sputtering techniques like DCMS or RF sputtering to achieve balanced deposition rates and high-quality film properties. Bipolar HiPIMS enhances process stability and film uniformity by alternating the polarity, which helps mitigate charge accumulation issues. Synchronized HiPIMS controls precise pulse timing to maximize ion energy impact and improve substrate interaction, further enhancing the structural properties of the coatings. Hence, to pave the way for future research and development in this area, insights of the HiPIMS have been presented that underline the role of HiPIMS in meeting the demanding requirements of advanced industrial applications. Overall, this review article comprehensively analyzes the recent strategies and technological innovations in HiPIMS and highlights the significant potential of HiPIMS for advancing the nitride coating field. Full article

In this study, CoCrFeNiY_x (x = 0, 0.1, 0.2, 0.3) high entropy alloy (HEA) coatings were produced on Ti6Al4V by laser cladding. The influence of Y on the microstructure and mechanical properties of CoCrFeNi HEA coatings was systematically examined. The analysis uncovered that the coatings primarily consist of three principal phases: α(Ti), Ti₂Ni, and TiC. The incorporation of Y led to enhanced lattice distortion, which positively influenced solid solution strengthening. Moreover, grain refinement resulted in a denser microstructure, significantly reducing internal defects and thereby enhancing the coating’s performance. The average microhardness of the CoCrFeNiY_0.2 coating was 702.46 HV_0.2. The wear rates were 1.16 × 10⁻³ mm³·N⁻¹·m⁻¹ in air and 3.14 × 10⁻³ mm³·N⁻¹·m⁻¹ in a neutral solution, which were 27.0% and 30.8% lower than those of the CoCrFeNi coatings, respectively, indicating superior wear resistance. The Y content in the CoCrFeNiY_0.3 coating was excessively high, resulting in the formation of Y-rich clusters. The accumulation of these impurities at the grain boundaries led to crack and pore formation, thereby reducing the wear resistance of the coating. Our study demonstrated that laser cladding an optimal amount of Y-doped CoCrFeNi HEA coatings on the Ti6Al4V substrate significantly enhanced the microstructure and mechanical properties of the substrate, particularly its wear resistance in both air and neutral environments, thereby improving the durability and reliability of titanium alloys in practical applications. Full article

In this study, in order to improve the characteristics of the vegetable-based cutting fluids used in the MQL technique and increase the machining performance of MQL and its positive effects on sustainable manufacturing, the effects of the MQL method with nano-Al₂O₃ additives on surface roughness (Ra) and cutting temperature (Ctt) were examined through turning experiments carried out by adding nano-Al₂O₃ to the vegetable-based cutting fluid. For this purpose, machining tests were carried out on hot work tool steel alloyed with Cr-Ni-Mo that has a delivery hardness of 45 HRC. In hard machining experiments, three techniques for cooling and lubricating (dry cutting, MQL, and nano-MQL), three cutting speeds (V) (100, 130, 160 m/min), three feed rates (f) (0.10, 0.125, and 0.15 mm/rev), and two different ceramic cutting tools (uncoated and TiN-coated with PVD methods) were used as control factors. For Ra, the nano-MQL method provided an average of 21.49% improvement compared to other cooling methods. For Ctt, this rate increased to 26.7%. In crater wear areas, the nano-MQL method again exhibited the lowest wear values, decreasing performance by approximately 50%. The results of this research showed that the tests conducted using the cooling of nano-MQL approach produced the best results for all output metrics (Ra, Ctt, and crater wear). Full article

This work aims at reducing abrasion between titanium alloy parts, such as drive shafts and support pairs used in aviation. Three different NiCrBSi coatings, Ni40, Ni50, and Ni60, are prepared on surfaces of Ti6Al4V by laser cladding. The microstructural and mechanical properties of these coatings are analyzed by scanning electron microscope (SEM) and a microhardness tester. The tribological properties of the NiCrBSi coatings undergoing friction with Ti6Al4V are tested using a wear testing machine. The results show that the Vickers hardnesses of the Ni40, Ni50, and Ni60 coatings are 490 HV₀.₃, 609 HV₀.₃, and 708 HV₀.₃, respectively. For the above NiCrBSi coatings, more hard phases are produced with increases in the amounts of Cr in the powders, resulting in increases in the coatings’ hardnesses. The wear test results show that the NiCrBSi coatings could reduce the friction coefficients, which gradually decreased with increases in the coatings’ hardnesses. Both the coating-specific wear rates and the friction pair wear losses initially decreased and then increased. The Ni50 coating and the Ti6Al4V friction pair undergoing friction with the Ni50 coating showed the best wear performance, with a specific wear rate and wear loss of 0.51 × 10⁻⁷ mm³/(N·m) and 7.8 mg, respectively. The specific wear rates for Ni50 were only 8.4%, 35.4%, and 37.0% of the Ti6Al4V, Ni40, and Ni60, respectively. In addition, the friction pair wear loss was only 36.4%, 52.5%, and 55.3% of that while undergoing friction with Ti6Al4V, Ni40, and Ni60, respectively. The NiCrBSi coatings prepared on the surface of Ti6Al4V show excellent antifriction and wear resistance properties, providing a viable solution for the design of wear-resistant coatings on load-bearing and non-load-bearing titanium alloy parts. Full article

The CoCrFeNi₂Mo_x (x = 0, 0.4, 0.5, 1.0, x values in atomic ratio) high-entropy alloy coatings were designed and prepared on the Ti-6Al-4V substrate by laser cladding technology, their microstructures, and dry sliding wear resistance were studied in detail. When x < 0.4, the coatings were mainly composed of BCC solid solution phase, (Ni, Co)Ti₂ phase, and α-Ti phase. When x ≥ 0.4, the new σ phase appeared in the coatings. As the Mo content increases from 0 to 1.0, the hardness showed a trend of first increasing and then decreasing, especially when x = 0.5, the coating hardness reached its maximum (882 HV), which was 2.65 times the hardness of the Ti-6Al-4V substrate. The CoCrFeNi₂Mo_x high-entropy alloy coatings significantly improved the wear resistance of Ti-6Al-4V substrate, and with the increase in Mo content, the friction coefficient, widths/depths of worn tracks and wear rates of the coatings showed a trend of first decreasing and then increasing. In particular, when x = 0.5, the CoCrFeNi₂Mo_0.5 high-entropy alloy coating has the lowest friction coefficient (0.63), widths/depths of worn tracks (width: 803.690 μm; depth: 20.630 μm) and wear rate (5.136 × 10⁻⁵ mm³/(N·m)), which is one order of magnitude smaller than that of the substrate (3.694 × 10⁻⁴ mm³/(N·m)), demonstrating the best wear resistance. This is mainly because the appropriate proportion of hard α-Ti and σ phases effectively played a supporting role in resisting wear, while the relatively soft and dispersed BCC and (Ni, Co)Ti₂ phases could effectively prevent the occurrence of brittle fracture during wear test process. Full article

Inconel 718 is a Ni superalloy with superior mechanical properties, even at high temperatures. However, due to its high hardness and low thermal conductivity, it is considered a difficult-to-machine material. This material is widely used in applications that require good dimensional stability, making the milling process the most used in machining this alloy. The wear resulting from this process and the quality of the machined surface are still challenging factors when it comes to Inconel 718. TiAlN-based coating has been used on cutting tools with Yttrium as a doping element to improve the process performance. Based on this, this work evaluated the machined surface integrity and wear resistance of cutting tools coated using Physical Vapor Deposition (PVD) HiPIMS with TiAlYN in the end milling of Inconel 718, varying the process parameters such as cutting speed (v_c), feed per tooth (f_z), and cutting length (L_cut). It was verified that the L_cut is the parameter that exerts the most significant influence since, even at small distances, Inconel 718 already generates high tool wear (TW). Furthermore, the main wear mechanisms were abrasive and adhesive wear, with the development of a built-up edge (BUE) under a125 m/min feed rate (f) and a L_cut = 15 m. Chipping, cracking, and delamination of the coating were also observed, indicating a lack of adhesion between the coating and the substrate, suggesting the need for a good interlayer or the adjustment of the PVD parameters. Full article