Search Results (566)

This work investigated the effect of high-nitrogen/low-hydrogen mixed atmosphere heat treatment on the electrochemical corrosion and wear resistance of plasma-sprayed FeCoNiCrAl high-entropy alloy (HEA) coatings. The HEA coatings were sequentially prepared through annealing at 400, 600, and 800 °C for 6 h. The heat treatment method was conducted in a vacuum tube furnace under 0.1 MPa total pressure, with gas flow rates set to 300 sccm N₂ and 100 sccm H₂. The XRD results indicated that the as-deposited coating exhibited α-Fe (BBC) and Al_0.9Ni_4.22 (FCC) phases, with an Fe_0.64N_0.36 nitride phase generated after 800 °C annealing. The electrochemical measurements suggested that an exceptional corrosion performance with higher thicknesses of passive film and double-layer capacitance can be detected based on the point defect model (PDM) and effective capacitance model. Wear tests revealed that the friction coefficient at 800 °C decreased by 3.84% compared to that in the as-sprayed state due to the formation of a dense nitride layer. Molecular orbital theory pointed out that the formation of bonding molecular orbitals, resulting from the overlap of valence electron orbitals of different atomic species in the HEA coating system, stabilized the structure by promoting atomic interactions. The wear mechanism associated with stress redistribution and energy balance from compositional synergy is proposed in this work. Full article

This study employs Geographic Information Systems (GIS) combined with multivariate statistical techniques to evaluate soil contamination at two landfill sites in Al-Kharj, Saudi Arabia. A total of 32 soil samples were collected and analyzed for heavy metals and metalloids (HMs) using a range of contamination indices and established soil quality standards. GIS mapping revealed that the Al-Kharj landfill 1 (Kj1) experienced a steady area expansion from 2014 through 2025, while landfill Kj2 expanded from 2014 until 2022, after which its area contracted following the construction of additional facilities. The average values of HMs observed were as follows: Fe (9909 mg/kg), Al (6709 mg/kg), Mn (155.9 mg/kg), Zn (36.4 mg/kg), Cr (24.1 mg/kg), V (22.2 mg/kg), Ni (19.5 mg/kg), Cu (8.20 mg/kg), Pb (7.91 mg/kg), Co (4.32 mg/kg), and As (2.29 mg/kg). Notably, Kj2 exhibited overall higher HM concentrations than Kj1, with particularly elevated levels of Cr, Ni, and Pb. Although most HMs remained within internationally accepted safety limits, only three samples (9.4% of the total) exceeded the WHO threshold for Pb (>30 mg/kg). An analysis using contamination and enrichment factors pointed to increased concentrations of Pb, Zn, and Cr, suggesting localized anthropogenic contributions. Additionally, all samples recorded an ecological risk index (Eri) below 40, and the levels of As, Cr, and Pb consistently stayed under their respective effects range-low (ERL) thresholds, indicating minimal contamination risks. The variations in HM contamination between the sites are likely attributable to differences in the sources of metal inputs and removal processes. These findings highlight the need for continuous monitoring and localized remediation strategies to ensure environmental safety and sustainable landfill management. Full article

This study investigates the effect of Al_x and Ti_x content (x = 0.1, 0.2, 0.3, 0.4, 0.5, and 0.6) on the microstructural evolution and mechanical properties of Co-free high-entropy Al_xTi_xCrFe₂Ni alloys in both as-cast and homogenized conditions. The research focused on the characterization of structural features, melting behavior, and mechanical performance. Microstructural characterization was carried out using optical microscopy, scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction (XRD), and differential thermal analysis (DTA). Mechanical properties were evaluated through Vickers hardness testing and uniaxial compression tests. Increasing the Al and Ti content induced a transformation from a single-phase FCC structure to a dual-phase BCC structure, with the primary BCC phase strengthened by spherical precipitates rich in Al, Ti, and Ni. Homogenization annealing at 1100 °C led to an overall improvement in the mechanical properties. The Al_0.3Ti_0.3CrFe₂Ni alloy exhibited the most balanced combination of strength and ductility after annealing, achieving a compressive yield strength of 1510 MPa, a compressive strength of 3316 MPa, and a compressive plastic strain of 45%. Full article

The microstructure, phase composition, and high-temperature oxidation resistance of Fe-free AlCoCrNiNb_0.2 and AlCoCr_0.5NiNb_0.2 high-entropy alloys (HEAs) were investigated. In the as-cast HEAs, niobium was found to mainly release as a Laves phase in the interdendritic region, and its solubility in the dendrites of the BCC solid solution was about 2 at.%. Both samples exhibited parabolic behavior during 100 h oxidation at 1000 °C and 1100 °C. The AlCoCrNiNb_0.2 alloy demonstrated higher resistance to high-temperature oxidation compared to AlCoCr_0.5NiNb_0.2. The specific weight changes after 100 h of isothermal holding at 1000 °C and 1100 °C were 0.65 mg/cm² and 1.31 mg/cm², respectively, which are superior compared to the Fe-containing HEAs. Cr was revealed to play an important role in the oxidation behavior of the HEAs, decreasing the parabolic oxidation rate constant and increasing the activation energy of the oxidation process in the alloys. Full article

This study synthesized FeNiCuAlX high-entropy alloys (HEAs) (where X = Cr, Co, Mn) using arc melting and investigated their high-temperature oxidation behavior in air at 900 °C. The oxidation kinetics of all alloys followed a parabolic rate, with the oxidation rate constants (kp) of FeNiCuAlCr, FeNiCuAlCo, and FeNiCuAlMn being approximately two to three orders of magnitude lower than that of the FeNiCu alloy. Specifically, FeNiCuAlCr exhibited the lowest kp value of 1.72 × 10⁻⁶ mg²·cm⁴/s, which is significantly lower than those of FeNiCuAlCo (3.29 × 10⁻⁶ mg²·cm⁴/s) and FeNiCuAlMn (1.71 × 10⁻⁵ mg²·cm⁴/s). This suggests that the addition of chromium promotes the formation of a dense Al₂O₃/Cr₂O₃ oxide layer, significantly enhancing the oxidation resistance. Furthermore, corrosion resistance was assessed through potentiodynamic polarization and electrochemical impedance spectroscopy in a 3.5% NaCl solution. FeNiCuAlCr demonstrated exceptional resistance to localized corrosion, as indicated by its low corrosion current density (45.7 μA/cm²) and high pitting potential (−0.21 V), highlighting its superior corrosion performance. Full article

The erosion resistance of materials against solid particles is a very important property, especially in the transportation of powders or in aeronautics (dust inside jet engines). There is a strong need to introduce new materials that have higher solid particle erosion resistance than state-of-the-art materials. Thus, in the present work, the solid erosion particles of high entropy alloys (HEAs) based on the Al0.7CoCrFeNi matrix were studied compared to the state-of-the-art stainless steel AISI 304. Furthermore, the effect of the addition of Ti to HEAs on hardness and erosion resistance was investigated. Current research included the development of the chemical composition of a new kind of HEA designed on the basis of thermodynamical calculations performed in CALPHAD, its manufacturing, full characterization involving microstructural and phase analyses, hardness measurements, solid particle erosion tests, and finally, the elucidation of erosion mechanisms. It was found that HEAs showed higher hardness as well as erosion resistance than AISI 304. Moreover, it was found that the increase in Ti content in an HEA resulted in an increase in the hardness and resistance to the erosion of the studied HEA. As the main reason for this phenomenon, the stabilization of the β-BCC phase, suppression of the α-FCC phase, and the appearance of the Ni₃Ti phase in the studied HEA were claimed. Full article

Milk powder is a key nutritional alternative to breastfeeding, but its thermal properties, which vary with temperature, can affect its quality and shelf life. However, there is little information about the physical and chemical properties of powdered milk in several countries. This dataset contains the result of an analysis of the aflatoxins, macroelement and microelement concentrations, oxidative stability, and fatty acid profile of infant formula milk powder. The concentrations of Al, As, Ba, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Se, V, and Zn in digested powdered milk samples were quantified through inductively coupled plasma optical emission spectrometry (ICP OES). Thermogravimetry (TG) and differential scanning calorimetry (DSC) were used to estimate the oxidative stability of infant formula milk powder, while the methyl esters of the fatty acids were analyzed by gas chromatography. Most milk samples showed significant concentrations of As (0.5583–1.3101 mg/kg) and Pb (0.2588–0.0847 mg/kg). The concentrations of aflatoxins G2 and B2 are below the limits established by Brazilian regulatory agencies. The thermal degradation behavior of the samples is not the same due to their fatty acid compositions. The data presented may be useful in identifying compounds present in infant milk powder used as a substitute for breast milk and understanding the mechanism of thermal stability and degradation, ensuring food safety for those who consume them. Full article

This study systematically investigates the effects of heat treatment at 800–1000 °C on the microstructure and mechanical properties of 10 wt.% TiB₂@Ti/AlCoCrFeNi_2.1 eutectic high-entropy alloy matrix composites (EHEAMCs) prepared by vacuum hot-pressing sintering. The results show that the materials consist of FCC, BCC, TiB₂, and Ti phases, with a preferred orientation of the (111) crystal plane of the FCC phase. As the temperature increases, the diffraction peak of the BCC phase separates from the main FCC peak and its intensity increases, while the diffraction peak positions of the FCC and BCC phases shift at small angles. This is attributed to the diffusion of TiB₂@Ti from the grain boundaries into the matrix, where the Ti solid solution increases the lattice constant of the FCC phase. Microstructural observations reveal that the eutectic region transforms from lamellar to island-like structures, and the solid solution zone narrows. With increasing temperature, the Ti concentration in the solid solution zone increases, while the contents of elements such as Ni decrease. Element diffusion is influenced by binary mixing enthalpy, with Ti and B tending to solidify in the FCC and BCC phase regions, respectively. The mechanical properties improve with increasing temperature. At 1000 °C, the average hardness is 579.2 HV, the yield strength is 1294 MPa, the fracture strength is 2385 MPa, and the fracture strain is 19.4%, representing improvements of 35.5% and 24.9% compared to the as-sintered state, respectively, without loss of plasticity. The strengthening mechanisms include enhanced solid solution strengthening due to the diffusion of Ti and TiB₂, improved grain boundary strength due to the diffusion of alloy elements to the grain boundaries, and synergistic optimization of strength and plasticity. Full article

High-entropy alloy (HEA) particle-reinforced metal matrix composites (MMCs) are a new generation of MMCs with potential applications as orthopedic material in automotive, aerospace, and biomedical fields. In this study, AlCoCrFeNi HEA-reinforced Ti-6Al-4V metal matrix composites (MMCs) were prepared by microwave sintering. The microstructural aspects of the MMC were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), with an emphasis on the interdiffusion (ID) layer. The mechanical properties of the composites were studied by micro-pillar compression at the micro-length scale. The results show that the ID layer exists between the HEA particles and the matrix, is equiaxed in nature, and leads towards metallurgical bonding within the composite. The strength of this ID layer (1573 MPa of yield strength and 1867 MPa of compressive strength) and its Young’s modulus (570 MPa) were about 1.5 times lower than that of the matrix. The HEA particles exhibit the highest strength (2157 MPa of yield strength and 3356 MPa of compressive strength) and Young’s modulus (643 MPa), whereas the matrix falls in between 2372 MPa of yield strength and 2661 MPa of compressive strength, and a Young’s modulus of 721 MPa. Full article

In this study, powders based on a high-entropy AlCoCrFeNi alloy obtained by mechanical alloying were successfully applied to a 316L stainless steel substrate by detonation spraying under various conditions. Their microstructural features, phase composition, hardness, and wear resistance were studied. A comparative analysis between the initial powder and the coatings was performed, including phase transformation modeling using Thermo-Calc under non-equilibrium conditions. The results showed that the phase composition of the powder and coatings includes body-centered cubic lattice (BCC), its ordered modification (B2), and face-centered cubic lattice FCC phases, which is consistent with the predictions of the Scheil solidification model, describing the process of non-equilibrium solidification, assuming no diffusion in the solid phase and complete mixing in the liquid phase. Rapid solidification and high-speed impact deformation of the powder led to significant grain refinement in the detonation spraying coating, which ultimately improved the mechanical properties at the micro level. The data obtained demonstrate the high efficiency of the AlCoCrFeNi coating applied by detonation spraying and confirm its potential for use in conditions of increased wear and mechanical stress. AlCoCrFeNi coatings may be promising for use as structural materials in the future. Full article

For the first time, the deposition area of heavy metals and other trace elements (Al, Ba, Cd, Co, Cr, Cu, Fe, Mn, Ni, P, Pb, S, Sr, Sb, V, Zn, and Hg) on the territory surrounding a landfill of domestic (municipal) waste at the 9th km of the Vilyuisky tract of Yakutsk within a radius of 51 km was assessed using the method of moss biomonitors and ICP-OES as an analytical technique. Mosses were analyzed for radionuclide content (⁴⁰K, ¹³⁷Cs, ²¹² Pb, ²¹⁴Pb, ²¹²Bi, ²¹⁴Bi, ²⁰⁸Tl, ⁷Be, and ²²⁸Ac) in a number of selected samples by semiconductor gamma spectrometry. The results of the examination of moss samples by ICP-OES indicate the presence of large amounts of toxic Ba and metal debris (Al, Co, Cr, Fe, S, and Pb) at the landfill. In addition, it is shown that the investigated samples contain elements such as Cd, Co, Cr, Cu, Cu, Mn, Ni, Pb, Sr, V, Zn, and Hg. The method of gamma spectrometry revealed that the studied samples contain such radioactive elements as ¹³⁷Cs, daughter products of ²³⁸U and ²³²Th. Detection of the same heavy metals and radionuclides in the atmospheric air of the city and in the vegetation near the landfill may indicate that one of the sources of environmental pollution may be products of incineration of the landfill contents at the 9th km of the Vilyuisky tract. Full article

This study investigates the influence of environmental variables on the elemental composition of Hypnum cupressiforme Hedw. mosses in Georgia and the Republic of Moldova, within moss biomonitoring studies aimed at analyzing atmospheric deposition patterns. Moss samples of Hypnum cupressiforme, characterized by a cosmopolitan distribution and a wide range of habitats, were collected from diverse geographical and climatic zones and analyzed for Al, Ba, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Sr, V, and Zn. Statistical methods (Spearman correlations, PCA, Kruskal–Wallis tests) were applied to evaluate interactions between elemental concentrations and factors such as topography, climate, land cover, etc. Results revealed strong correlations among lithogenic elements (Al, Co, Cr, Fe, Ni, and V), indicating natural weathering sources, while Cu exhibited potential anthropogenic origins in the Republic of Moldova. Elevated Cd and Pb levels in Georgian high-altitude regions were linked to wet deposition and steep slopes, whereas Moldovan samples showed higher Sr and Zn concentrations, likely driven by soil erosion in carbonate chernozems. The study highlights geogenic and climatic influences on element accumulation by moss, offering insights into the effectiveness of moss biomonitoring across heterogeneous landscapes. Full article

Potentially toxic elements such as cadmium (Cd) in agricultural soils represent a global concern due to their toxicity and potential accumulation in the food chain. However, our understanding of cadmium’s complex sources and the mechanisms controlling its spatial distribution across diverse edaphic and geological contexts remains limited, particularly in underexplored agricultural regions. Our study aimed to assess the total accumulated Cd content in soils under avocado cultivation and its association with edaphic, geochemical, and geomorphological variables. To this end, we considered the total concentrations of other metals and explored their associations to gain a better understanding of Cd’s spatial distribution. We analyzed 26 physicochemical properties, the total concentrations of 22 elements (including heavy and trace metals such as As, Ba, Cr, Cu, Hg, Ni, Pb, Sb, Se, Sr, Tl, V, and Zn and major elements such as Al, Ca, Fe, K, Mg, and Na), and six geospatial variables in 410 soil samples collected from various avocado-growing regions in Peru in order to identity potential associations that could help explain the spatial patterns of Cd. For data analysis, we applied (1) univariate statistics (skewness, kurtosis); (2) multivariate methods such as Spearman correlations and principal component analysis (PCA); (3) spatial modeling using the Geodetector tool; and (4) non-parametric testing (Kruskal–Wallis test with Dunn’s post hoc test). Our results indicated (1) the presence of hotspots with Cd concentrations exceeding 3 mg·kg⁻¹, displaying a leptokurtic distribution (skewness = 7.3); (2) dominant accumulation mechanisms involving co-adsorption and cation competition (Na⁺, Ca²⁺), as well as geogenic co-accumulation with Zn and Pb; and (3) significantly higher Cd concentrations in Leptosols derived from Cretaceous intermediate igneous rocks (diorites/tonalites), averaging 1.33 mg kg⁻¹ compared to 0.20 mg·kg⁻¹ in alluvial soils (p < 0.0001). The factors with the greatest explanatory power (q > 15%, Geodetector) were the Zn content, parent material, geological age, and soil taxonomic classification. These findings provide edaphogenetic insights that can inform soil cadmium (Cd) management strategies, including recommendations to avoid establishing new plantations in areas with a high risk of Cd accumulation. Such approaches can enhance the efficiency of mitigation programs and reduce the risks to export markets. Full article

Based on the innovative mode driven by “data + artificial intelligence”, in this study, three methods, namely Gaussian noise (GAUSS Noise), the Generative Adversarial Network (GAN), and the optimized Generative Adversarial Network (GANPro), are adopted to expand and enhance the collected dataset of element contents and the hardness of the AlCoCrCuFeNi high-entropy alloy. Bayesian optimization with grid search is used to determine the optimal combination of hyperparameters, and two interpretability methods, SHAP and permutation importance, are employed to further explore the relationship between the element features of high-entropy alloys and hardness. The results show that the optimal data augmentation method is Gaussian noise enhancement; its accuracy reaches 97.4% under the addition of medium noise (σ = 0.003), and an optimal performance prediction model based on the existing dataset is finally constructed. Through the interpretability method, it is found that the contributions of Al and Ni are the most prominent. When the Al content exceeds 0.18 mol, it has a positive promoting effect on hardness, while Ni and Cu exhibit a critical effect of promotion–inhibition near 0.175 mol and 0.14 mol, respectively, revealing the nonlinear regulation law of element contents. This study solves the problem of revealing the mutual relationship between the element contents and hardness of high-entropy alloys in the case of a lack of alloy data and provides theoretical guidance for further improving the performance of high-entropy alloys. Full article

This paper studies how heat treatments influence the corrosion of an AlCoCrFeNi_2.1 eutectic high-entropy alloy (EHEA) in a 3.5 wt% NaCl solution, by comparing the corrosion behaviors of as-cast, 600 °C heat-treated, and 1000 °C heat-treated samples using microstructure characterization, electrochemical measurements, and surface characterization. The electrochemical results show that the pitting potential rises and the passive current density and passive film resistance are almost changeless with an increasing heat treatment temperature. The enhancement in the pitting corrosion resistance results from the increased amount of the Cr-rich FCC phase and decreased amount of the B2 phase rich in the Al element, which are induced by the heat treatment. On one hand, this microstructure evolution can make the passive film have more Cr₂O₃ and less Al₂O₃, thereby enhancing its protective properties, as confirmed by the X-ray photoelectron spectroscopy analysis. On the other hand, the decreased amount of the Al-rich B2 phase can make the pitting corrosion less prone to initiate since the B2 phase can act as the pit initiation site, which is supported by the observation of corrosion morphologies, due to its higher electrochemical activity. In a summary, the heat treatment is beneficial for improving the pitting corrosion resistance of the AlCoCrFeNi_2.1 EHEA. Full article