Search Results (1,492)

Ferronickel slag and ground granulated blast-furnace slag (GGBFS) are solid waste by-products from the metallurgical industry. When incorporated into concrete, they help promote resource utilization, reduce hydration heat, and lower both solid waste emissions and the carbon footprint. To facilitate the application of ferronickel slag–GGBFS concrete in 3D printing, this study examines how aggregate size and nozzle diameter affect its performance. The investigation involves in situ printing, rheological characterization, mechanical testing, and scanning electron microscopy (SEM) analysis. Results indicate that excessively large average aggregate size negatively impacts the smooth extrusion of concrete strips, resulting in a cross-sectional width that exceeds the preset dimension. Excessively small average aggregate size results in insufficient yield stress, leading to a narrow cross-section of the extruded strip that fails to meet printing specifications. The extrusion performance is closely related to both the average aggregate size and nozzle diameter, which can significantly influence the normal extrusion stability and print quality of 3D printed concrete strips. The thixotropic performance improves with an increase in the aggregate size. Both compressive and flexural strengths improve with increasing aggregate size but decrease with an increase in the printing nozzle size. Anisotropy in mechanical behavior decreases progressively as both parameters mentioned increase. By examining the cracks and pores at the interlayer interface, this study elucidates the influence mechanism of aggregate size as well as printing nozzle parameters on the mechanical properties of 3D printed ferronickel slag–GGBFS concrete. This study also recommends the following ranges. When the maximum aggregate size exceeds 50% of the nozzle diameter, smooth extrusion is not achievable. If it falls between 30% and 50%, extrusion is possible but shaping remains unstable. When it is below 30%, both stable extrusion and good shaping can be achieved. Full article

As the global emphasis on sustainable development intensifies, the integration of digital technologies (DTs) into efforts to address the Sustainable Development Goals (SDGs) has gained increasing attention. However, existing research on the link between the SDGs and DTs remains fragmented and lacks a comprehensive perspective on their interconnections. We aimed to address this gap by conducting a large-scale bibliometric analysis based on Elsevier’s SDG research mapping technique. Drawing on approximately 1.17 million publications related to both the 17 SDGs and 11 representative DTs, we explored research trends in the SDG–DT association, identified DTs that are most frequently tied to specific SDGs, and uncovered emerging areas of research within this interdisciplinary domain. Our results highlight the rapid expansion in the volume and variety of SDG–DT studies. Our findings shed light on the widespread relevance of artificial intelligence and robotics, the goal-specific applications of technologies such as 3D printing, cloud computing, drones, and extended reality, as well as the growing visibility of emerging technologies such as digital twins and blockchain. These findings offer valuable insights for researchers, policymakers, and industry leaders aiming to strategically harness DTs to support sustainable development and accelerate progress toward achieving the SDGs. Full article

Ceramic pastes used in additive manufacturing offer several advantages, including low production costs due to the availability of raw materials and efficient processing methods, as well as a reduced environmental footprint through minimized material waste, optimized resource use, and the inclusion of recyclable or sustainably sourced components. This study evaluates the effect of diatomite content in a ceramic paste composed of carboxymethyl cellulose, kaolinite, and feldspar on its extrusion behavior and thermal conductivity, with additional analysis of its implications for microstructure, mechanical properties, and thermal performance. Four ceramic pastes were prepared with diatomite additions of 0, 10, 30, and 60% by weight. Thermal conductivity, extrusion behavior, morphology, and distribution were examined using scanning electron microscopy (SEM), while thermal degradation was assessed through thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results show that increasing diatomite content leads to a reduction in thermal conductivity, which ranged from 0.719 W/(m·°C) for the control sample to 0.515 W/(m·°C) for the 60% diatomite sample, as well as an improvement in extrusion behavior. The ceramic paste demonstrated adequate extrusion performance for 3D printing at diatomite contents above 30%. These findings lay the groundwork for future research and optimization in the development of functional ceramic pastes for advanced manufacturing applications. Full article

Total knee arthroplasty is an extensive orthopedic surgery for patients with severe cases of osteoarthritis. This surgery restores the range of motion in the knee joint and allows for pain-free movement. Advancements in medical techniques used in the surgical zone and implant technology, as well as the management of operations and administration for around two decades prior, have hugely improved surgical outcomes for patients. In this study, advancements in TKA were examined through exploring aspects such as robotic surgery, new implants and materials, minimally invasive surgery, and post-surgery rehabilitation. This paper entails a review of the peer-reviewed literature published between 2005 and 2025 in the PubMed and Google Scholar databases. For predictors, we incorporated clinical relevance together with methodological soundness and relation to review questions to select relevant research articles. We used the PRISMA flowchart to illustrate the article selection system in its entirety. Since robotic surgical and navigation systems have been implemented, surgical accuracy has improved, there is an increased possibility of ensuring alignment, and the use of cementless and 3D-printed implants has increased, offering durable long-term fixation features. The trend in the current literature is that minimally invasive knee surgery (MIS) techniques reduce permanent pain after surgery and length of hospital stays for patients, though the long-term impact still needs to be established. There is various evidence outlining that the enhanced recovery after surgery (ERAS) protocols show positive results in terms of functional recovery and patient satisfaction. The integration of these new advancements enhances TKA surgeries and translates them into ‘need of patient’ procedures, ensuring improved results and increases in patient satisfaction. The aim of this study was to perform a comprehensive analysis of the existing literature regarding TKA advancement studies to identify current gaps and problems. Full article

To meet the rapid maneuverability and lightweight demands of micro-nano satellites, a space micro solid thruster using 3D-printed short glass fiber reinforced polyamide 6 (PA6GF) composites was developed. Thruster shells with wall thicknesses of 4, 3, and 2.5 mm were designed, and ground ignition tests were conducted to monitor chamber pressure and shell temperature. Compared with conventional metallic thrusters, PA6GF composites have exhibited excellent thermal insulation and sufficient mechanical strength. Under 8 MPa and 2773 K ignition conditions, the shell thickness was reduced to 2.5 mm and could withstand pressures up to 10.37 MPa. These results indicate that PA6GF composites are well-suited for space micro solid thrusters with inner diameters of 15–70 mm, offering new possibilities for lightweight space propulsion system design. Full article

This study proposes a continuous preparation strategy for poly (l-lactic acid) (PLLA) scaffolds with oriented hierarchical microporous structures for bone repair. A PLLA-oriented multi-stage microporous bone repair scaffold (hereafter referred to as the oriented multi-stage microporous scaffold) was designed using a novel extrusion foaming technology that integrates fused deposition modeling (FDM) 3D printing with supercritical carbon dioxide (SC-CO₂) microcellular foaming technology. The influence of the 3D-printed structure on the microcellular morphology of the oriented multi-stage microporous scaffold was investigated and optimized. The combination of FDM and SC-CO₂ foaming technology enables a continuous extrusion foaming process for preparing oriented multi-stage microporous scaffolds. The mechanical strength of the scaffold reached 15.27 MPa, meeting the requirements for bone repair in a low-load environment. Notably, the formation of open pores on the surface of the oriented multi-stage microporous scaffold positively affected cell proliferation, differentiation, and activity, as well as the expression of anti-inflammatory and pro-inflammatory factors. In vitro cell experiments (such as CCK-8) showed that the cell proliferation rate in the oriented multi-stage microporous scaffold reached 100–300% after many days of cultivation. This work provides a strategy for the design and manufacture of PLLA scaffolds with hierarchical microcellular structures and biocompatibility for bone repair. Full article

Shark skin exhibits a well-defined multilayered architecture, consisting of three-dimensional denticles and an underlying dermal layer, which contributes to its passive drag reduction. However, the active drag reduction mechanisms of this interface remain largely unexplored. In this study, the Marangoni effect potentially arising from the active secretion of mucus on shark skin is investigated. A 3D-printed swimming robot with a porous substrate and a biomimetic shark denticle structure is developed. By introducing surfactants into the porous substrate and adjusting denticle arrangements, on-demand propulsion and controlled swimming trajectories are achieved. A superhydrophobic surface is fabricated on the swimming robot, which reduces water resistance and enhances propulsion. Moreover, denticles with a 30° attack angle demonstrate optimal propulsion performance in both Marangoni-driven hydrodynamics and aerodynamics. This study suggests that the secretion of mucus on shark skin may facilitate active drag reduction via the Marangoni effect, offering novel insights into the biomimetic structural design of autonomous swimming robots. Full article

Introduction: The important factor in applying substances for inner ear therapy is the atraumatic execution, as well as effective concentration uniformly distributed in all regions of the cochlea within a reasonable time frame. This study investigates whether an additional cochlear opening (“second-hole technique”) can improve fluid distribution and reduce intracochlear pressure during dye delivery into the cochlear models and human petrous bone. Material and Methods: Three experimental setups were used: an uncoiled scala tympani model, a full-scale 3D-printed cochlear model, and a human petrous bone. In all cases, 1% methylene blue-stained saline was infused using a cochlear catheter (MED-EL, Innsbruck, Austria) through the round window. Intracochlear pressure was measured via fiberoptic pressure sensors inserted through a burr hole (artificial cochlear models) or at the lateral semicircular canal (human petrous bone). A second hole was made on the helicotrema in the inner ear models or at the oval window of the human petrous bone to examine the effect of a second hole on intracochlear pressure and fluid distribution. Dye distribution and intracochlear pressure were measured in 3D artificial models at two flow rates (0.2 and 0.4 mL/h). The intracochlear pressure were measured in the human petrous bone at a fixed rate (0.4 mL/h). Results: The use of a second hole significantly improved dye distribution in 3D models at both flow rates (p < 0.05) and led to earlier saturation-level distribution. Intracochlear pressure remained significantly lower and more stable in models with a second hole (p < 0.05). In human petrous bones, pressure fluctuation was reduced by the second hole, though pressure still increased over time. Conclusions: Using a second-hole technique leads to a faster, uniform level of dye distribution throughout the cochlear models, as well as a lower intracochlear pressure, which can be assumed to be an essential factor for hearing preservation during dye application. Full article

This paper presents the results of an experimental study on the buckling and failure behavior of thin-walled square columns made from PLA and PETG polymers using FDM 3D printing technology. Thin-walled square columns made from thermoplastic materials, intended for use in lightweight load-bearing applications such as structural supports in transportation, construction, and mechanical assemblies, were tested under axial compression from the onset of buckling to complete failure. The novelty of this work lies in the application of an interdisciplinary experimental approach to the analysis of the behavior of thin-walled columns made of PLA and PETG materials during FDM 3D printing under compression until complete failure, as well as the use of acoustic and optical diagnostic methods for a comprehensive assessment of damage. The experimental results are as follows: Buckling load (N): PLA—1175 ± 32, PETG1—1910 ± 34, PETG2—1315 ± 27. Ultimate load (N): PLA—2770, PETG1—4077, PETG2—2847. Maximum strain: PLA—11.35%, PETG1—11.77%, PETG2—10.99%. Among the tested materials, PETG1 exhibited the highest resistance and energy absorption capacity upon failure, making it a favorable choice for manufacturing 3D-printed load-bearing columns. Full article

Understanding the rheological properties of fresh cement slurries is essential to maintain optimal pumpability, achieve dependable zonal isolation, and preserve long-term well integrity in oil and gas cementing operations and the 3D printing cement and concrete industry. However, accurately and efficiently modeling the rheological behavior of cement slurries remains challenging due to the complex fluid properties of fresh cement slurries, which exhibit non-Newtonian and thixotropic behavior. Traditional numerical solvers typically require mesh generation and intensive computation, making them less practical for data-scarce, high-dimensional problems. In this study, a physics-informed neural network (PINN)-based framework is developed to solve the governing equations of steady-state cement slurry flow in a tilted channel. The slurry is modeled as a non-Newtonian fluid with viscosity dependent on both the shear rate and particle volume fraction. The PINN-based approach incorporates physical laws into the loss function, offering mesh-free solutions with strong generalization ability. The results show that PINNs accurately capture the trend of velocity and volume fraction profiles under varying material and flow parameters. Compared to conventional solvers, the PINN solution offers a more efficient and flexible alternative for modeling complex rheological behavior in data-limited scenarios. These findings demonstrate the potential of PINNs as a robust tool for cement slurry rheological modeling, particularly in scenarios where traditional solvers are impractical. Future work will focus on enhancing model precision through hybrid learning strategies that incorporate labeled data, potentially enabling real-time predictive modeling for field applications. Full article

This study presents a theoretical model for the thermoelastic response in transmission-mode photoacoustic systems that feature a two-layer structure. The model incorporates volumetric optical absorption in both layers and is based on classical heat conduction theory, hyperbolic generalized heat conduction theory, and fractional heat conduction models including inertial memory in Generalizations of the Cattaneo Equation (GCEI, GCEII, and GCEIII). To validate the model, comparisons were made with the existing literature models. Using the proposed model, the thermoelastic photoacoustic response of a two-layer system composed of a 3D-printed porous polyamide (PA12) substrate coated with a thin, highly absorptive protective dye layer is analyzed. We obtain that the thickness and thermal conduction in properties of the coating are very important in influencing the thermoelastic component and should not be overlooked. Furthermore, the thermoelastic component is affected by the selected fractional model—whether it is subdiffusion or superdiffusion—along with the value of the order of the fractional derivative, as well as the optical absorption coefficient of the layer being investigated. Additionally, it is concluded that the phase has a greater impact than the amplitude when selecting the appropriate theoretical heat conduction model. Full article

The aim of this work was the preparation of ceramic monolithic catalysts for the catalytic oxidation of gaseous mixture of benzene, toluene, ethylbenzene and o-xylene BTEX. The possibility of using zirconium dioxide (ZrO₂) as a filament for the fabrication of 3D-printed ceramic monolithic carriers was investigated using fused filament fabrication. A mixed manganese and iron oxide, MnFeO_x, was used as the catalytically active layer, which was applied to the monolithic substrate by wet impregnation. The approximate geometric surface area of the obtained carrier was determined to be 53.4 cm², while the mass of the applied catalytically active layer was 50.3 mg. The activity of the prepared monolithic catalysts for the oxidation of BTEX was tested at different temperatures and space times. The results obtained were compared with those obtained with commercial monolithic catalysts made of ceramic cordierite with different channel dimensions, and with monolithic catalysts prepared by stereolithography. In the last part of the work, a kinetic analysis and the modeling of the monolithic reactor were carried out, comparing the experimental results with the theoretical results obtained with the 1D pseudo-homogeneous and 1D heterogeneous models. Although both models could describe the investigated experimental system very well, the 1D heterogeneous model is preferable, as it takes into account the heterogeneity of the reaction system and therefore provides a more realistic description. Full article

In this paper, titanium oxide nanoparticles (TiO₂-NPs) with complex surface topologies were obtained for the first time using simple procedures applied in laser sintering. Based on the obtained nanoparticles and polymethyl methacrylate-like photopolymer resin, a composite material (MPR/TiO₂-NPs) for 3D printing was created using the MSLA technology. Products made of the material containing from 0.001 to 0.1% wt. TiO₂-NPs didn’t contain internal defects and were less brittle than the resin without nanoparticles. Products made of the MPR/TiO₂-NPs material were well polished; after polishing, areas with a variation in the surface profile height of less than 10 nm were found on the surfaces. Nanoparticles in the volume of products made of the material are apparently unevenly distributed; there are alternating areas of micrometer sizes with slightly higher and slightly lower concentrations of nanoparticles. Spectroscopy showed that adding the developed nanoparticles promoted better polymerization of the MPR resin. The addition of nanoparticles to the material slightly increased its ability to generate active forms of oxygen and damage biomacromolecules. At the same time, the resulting material exhibits significant antibacterial properties and doen’t affect the growth and reproduction of animal cells. The created material can be a very effective basis for the additive manufacturing of products with improved physical and chemical properties and balanced biological activity. Full article

Introduction: Total temporomandibular joint replacement (TMJR) is a well-established surgical solution for patients with severe TMJ disorders. It aims to relieve chronic pain, restore jaw mobility, and significantly enhance quality of life. This systematic review evaluates QoL outcomes following TMJR, analyzes complication profiles, compares custom versus stock prostheses, explores pediatric applications, and highlights technological innovations shaping the future of TMJ reconstruction. Methods: A systematic search of PubMed, Embase, and the Cochrane Library was conducted throughout April 2025 in accordance with PRISMA 2020 guidelines. Sixty-four studies were included, comprising 2387 patients. Results: Primary outcomes assessed were QoL improvement, pain reduction, and functional gains such as maximum interincisal opening (MIO). Secondary outcomes included complication rates and technological integration. TMJR consistently led to significant pain reduction (75–87%), average MIO increases of 26–36 mm, and measurable QoL improvements across physical, social, and psychological domains. Custom prostheses were particularly beneficial in anatomically complex or revision cases, while stock devices generally performed well for standard anatomical conditions. Pediatric TMJR demonstrated functional and airway benefits with no clear evidence of growth inhibition over short- to medium-term follow-up. Complications such as heterotopic ossification (~20%, reduced to <5% with fat grafting), infection (3–4.9%), and chronic postoperative pain (~20–30%) were reported but were largely preventable or manageable. Recent advancements, including CAD/CAM planning, 3D-printed prostheses, augmented-reality-assisted surgery, and biofilm-resistant materials, are enhancing personalization, precision, and implant longevity. Conclusions: TMJR is a safe and transformative treatment that consistently improves QoL in patients with end-stage TMJ disease. Future directions include long-term registry tracking, growth-accommodating prosthesis design, and biologically integrated smart implants. Full article

Three-dimensional printing techniques can prepare complex bioceramic parts and scaffolds with high precision and accuracy, low cost, and customized geometry, which greatly broadens their application of 3D-printed bioceramics and bioceramic matrix composites in the clinical field. Nevertheless, the inadequate mechanical properties of 3D-printed bioceramic scaffolds, such as compressive strength, wear resistance, flexural strength, fracture toughness, and other properties, are a bottleneck problem and severely limit their application, which are overcome by introducing reinforcements. Three-dimensional printing techniques and the mechanical property of bioceramics and bioceramic matrix composites with different reinforcements, as well as their potential applications for bone tissue engineering, are discussed. In addition, the biological performance of 3D-printed bioceramics and scaffolds and their applications are presented. To address the challenges of insufficient mechanical strength and mismatched biological performance in bioceramic scaffolds, we summarize current solutions, including the advantages and strengthening effects of fiber, particle, whisker, and ion doping. The effectiveness of these methods is analyzed. Finally, the limitations and challenges in 3D printing of bioceramics and bioceramic matrix composites are discussed to encourage future research in this field. Our work offers a helpful guide to research and medical applications, especially application in the tissue engineering fields of bioceramics and bioceramic matrix composites. Full article