Search Results (262)

The heating rates and forming temperatures during the hot forming process of titanium alloys cause significant differences in phase transformation, grain size, and dislocation evolution. The formability and service performance of titanium alloy formed components are affected by these factors. This study investigated the hot flow behaviors of Ti-6Al-4V at temperatures ranging from 800 to 900 °C and heating rates ranging from 0.1 to 10 °C/s. These were tested via Gleeble hot tensile experiments, and the grain size and phase evolution were quantitatively characterized via EBSD and XRD. The results suggest that a higher heating rate decreases the β-phase transformation and dislocation density and inhibits grain coarsening, leading to better formability. The heating rate was introduced into the viscoplastic constitutive model for the first time to achieve accurate predictions of the microstructure and hot flow behavior under different heating rates. The prediction accuracy of the hot flow behavior and phase volume fraction reaches 92.93% and 94.97%. The current-assisted hot stamping experiments and finite element (FE) simulations of Ti-6Al-4V irregular cross-section components were carried out at temperatures of 800 and 900 °C and at heating rates of 1 and 3 °C/s. The results show that the rapidly heated formed components exhibit better thickness uniformity and yield strength. The FE simulation guided by the optimized constitutive model has achieved a 96.96% and 92.76% prediction accuracy for the thickness distribution and β-phase volume fraction, respectively. Full article

The advent of additive manufacturing (AM), also known as 3D printing, has revolutionized the production of titanium alloys, offering significant advantages in fabricating complex geometries with enhanced mechanical properties. This study investigates the variant-specific deformation mechanisms in HIP-treated TA15 (Ti-6.5Al-2Zr-1Mo-1V) titanium alloy, fabricated via selective electron beam melting (SEBM). The alloy exhibits a dual-phase (α+β) microstructure, where six distinct α variants are formed through the β→α phase transformation following the Burgers orientation relationship. Variant selection during AM leads to a non-uniform distribution of these α variants, with α6 (22.3%) dominating due to preferential growth. Analysis of the prismatic slip Schmid factor reveals that α4–α6 variants, with higher Schmid factors (>0.45), primarily undergo prismatic slip, while α1–α3 variants, with lower Schmid factors (<0.3), rely on basal or pyramidal slip and twinning for plastic deformation. In-grain misorientation axis (IGMA) analysis further reveals strain-dependent slip transitions: pyramidal slip is activated in α1–α3 variants at lower strains, while prismatic slip becomes the dominant deformation mechanism in α4–α6 variants at higher strains. Additionally, deformation twins, primarily {10–12}<1–101> extension twins (7.1%), contribute to the plasticity of hard-oriented α variants. These findings significantly enhance the understanding of the orientation-dependent deformation mechanisms in HIPed TA15 alloy and provide a crucial basis for optimizing the performance of additively-manufactured titanium alloys. Full article

The application fields of high-temperature titanium alloys are mainly concentrated in the aerospace, defense and military industries, such as the high-temperature parts of rocket and aircraft engines, missile cases, tail rudders, etc., which can greatly reduce the weight of aircraft while resisting high temperatures. However, traditional high-temperature titanium alloys containing multiple types of elements (more than six) have a complex impact on the solidification, deformation, and phase transformation processes of the alloys, which greatly increases the difficulty of casting and deformation manufacturing of aerospace and military components. Therefore, developing low-component high-temperature titanium alloys suitable for hot processing and forming is urgent. This study used data augmentation (Gaussian noise) to expedite the development of a novel quinary high-temperature titanium alloy. Utilizing data augmentation, the generalization abilities of four machine learning models (XGBoost, RF, AdaBoost, Lasso) were effectively improved, with the XGBoost model demonstrating superior prediction accuracy (with an R² value of 0.94, an RMSE of 53.31, and an MAE of 42.93 in the test set). Based on this model, a novel Ti-7.2Al-1.8Mo-2.0Nb-0.4Si (wt.%) alloy was designed and experimentally validated. The UTS of the alloy at 600 °C was 629 MPa, closely aligning with the value (649 MPa) predicted by the model, with an error of 3.2%. Compared to as-cast Ti1100 and Ti6242S alloy (both containing six elements), the novel quinary alloy has considerable high-temperature (600 °C) mechanical properties and fewer components. The microstructure analysis revealed that the designed alloy was an α+β type alloy, featuring a typical Widmanstätten structure. The fracture form of the alloy was a mixture of brittle and ductile fracture at both room and high temperatures. Full article

Titanium alloys, especially Ti6Al4V, are widely used in biomedical implants due to their biocompatibility and mechanical strength. However, their high elastic modulus (>100 GPa), compared to that of human bone (10–30 GPa), often causes stress shielding, reducing implant lifespan. To address this, titanium alloys with lower elastic modulus are under development. In this study, Ti-based multi-element alloy with 16 wt.% Nb samples were fabricated using laser powder bed fusion (L-PBF) from a premixed powder blend of Ti6Al4V and Nb-Hf-Ti. Processing high-melting Nb-based alloys via L-PBF poses challenges, which were mitigated through optimized parameters, including a maximum laser power of 100 W. Eleven parameter sets were employed to evaluate printability, microstructure, and mechanical properties. Microstructural analysis revealed Widmanstätten structures composed of α and β phases, along with isolated spherical pores. Reduced hatch spacing and slower laser speed led to increased hardness. The highest hardness (~43 HRC) was observed at the highest energy density (266 J/mm³), while the lowest (~28 HRC) corresponded to 44 J/mm³. Elastic modulus values ranged from 30 to 35 GPa, closely matching that of bone. These results demonstrate the potential of the developed Ti-based alloy containing 16 wt.% Nb as a promising candidate for load-bearing biomedical implants. Full article

Due to their excellent mechanical properties and good biocompatibility, titanium (Ti) and its alloys are widely used as biomaterials. However, when implanted in the body, metallic materials may cause serious complications such as wear and infection, leading to patient discomfort and, in some cases, the need for revision surgery. Micro-arc oxidation (MAO) is a surface modification technique that offers a promising strategy to overcome these challenges. This study investigated the impact of the microstructure of Ti-25 Ta-xNb alloys (x = 10, 20, and 30 wt%) and the variation in applied voltage during the MAO process on the characteristics of the TiO₂ oxide coatings formed. The alloys were treated by MAO at 200, 250, and 300 V using a bioactive electrolyte containing Ca, P, Mg, and Ag. EDS, SEM, XRD, Raman spectroscopy, and adhesion tests performed characterization. Results indicated that Nb addition stabilized the β phase and anticipated the potentiostatic regime. Increasing the voltage supplied to the system provides greater energy, prolonging the galvanostatic regime and promoting the formation of larger and more uniform pores. The oxide coating thickness ranged from approximately 3 to 10 μm, with a tendency to decrease at higher voltages. The coatings exhibited low c, with anatase and rutile phases predominating, the applied voltage and Nb concentration influencing their relative proportions. Even in small amounts, all electrolyte elements (P, Mg, and Ag) were successfully incorporated into the coatings under all conditions. Raman and XRD analyses confirmed a decrease in anatase and an increase in rutile phases with increasing voltage and Nb content. Mechanical testing revealed good adhesion of the coatings in all samples, with the best results obtained at 200 V. The findings demonstrate that the developed coatings exhibit promising characteristics for future surface engineering strategies aimed at improving the performance of metallic biomaterials. Full article

The torsional behavior during the deformation process of the axial closed die rolling the axial closed rolling (ACDR) forming is studied in this paper using a numerical simulation technique on TC11 titanium alloy. The axial and radial pinch angles, as well as the degree of specimen torsion, increased with the amount of deformation. The orientation distribution function (ODF) maps of the α-phase and β-phase were obtained by Electron Back Scatter Diffraction (EBSD) treatment of the TC11 titanium alloy. It can be noticed that there were different types of texture with different strengths in the ACDR samples, and in the xz and yz planes, textures in the direction of the column were predominantly of {0001} <2$\overline{1}\overline{1}$0> and {01$\overline{1}$0} <2$\overline{1}\overline{1}$0>; the weaker the texture was, the closer to the edge of the sample. In the xy plane, the texture structure was mainly distributed along the cone direction, and the textures were {$\overline{1}$2$\overline{1}$0} <10$\overline{1}$0> and {01$\overline{1}$0} <2$\overline{1}\overline{1}$0>. However, the closer to the edge position of the specimen, the higher the intensity of the texture, and the texture was {1$\overline{2}$1$\overline{2}$} <1$\overline{2}$16>. The β-phase is mainly distributed as {001} <100>, {110} <1$\overline{1}$0>, and {110} <001> textures within the specimen, and the texture strength is about 8.5 times. However, owing to the small proportion of the β-phase content in the specimen, the distribution pattern of its texture has a weak impact on the texture distribution of the overall specimen. A high degree of isotropy in the radial and tangential tensile properties, with a strength isotropy of over 99 percent and a plasticity isotropy of over 95 percent, resulted from the distribution of texture types with varying strengths and orientations within the ACDR specimens, which weakened the TC11 discs’ overall orientation. Full article

This study presents the characteristics of the Ti-33Mo-0.2C alloy, which belongs to the group of titanium alloys with a stable β phase and contains 0.27 wt% carbon; this is significantly higher than the permissible level for this alloy, which is 0.1 wt%. The Ti-33Mo-0.2C alloy was melted in a vacuum induction furnace with a cold copper crucible and subsequently processed into a 12 mm diameter rod through hot rolling and annealing under standard conditions. The microstructure, as well as the mechanical and physicochemical properties of the Ti-33Mo-0.2C alloy, were compared with those of the Ti-33Mo alloy of a similar chemical composition. The following techniques were used to characterize the microstructure and properties of the alloys: LM; SEM/EDS (WDS); XRD; and mechanical, creep, and corrosion testing. The conducted analyses demonstrated that the addition of approximately 0.2 wt% carbon to the Ti-33Mo alloy leads to the expected improvement in microstructural stability by reducing grain growth and inhibiting the precipitation of the α phase at β grain boundaries. Consequently, a unique simultaneous enhancement of both strength and ductility, with increased creep resistance, is observed while maintaining the excellent corrosion resistance of the investigated alloy. The observed beneficial effects and additional capabilities resulting from the presence of carbon in the investigated alloy justify the conclusion that carbon should no longer be regarded as an undesirable impurity, which stands in contrast to some previous statements. Full article

Laser shock peening (LSP) is an effective method to improve the fatigue property of metallic materials, and a thorough understanding of its strengthening mechanism is crucial for technology application. In this study, the LSP and fatigue tests of TC4 titanium alloy have been carried out. Combined with the structural characterization and the crystal plasticity finite element (CPFE) simulation, the relationship of stress distribution, microstructure evolution and fatigue performance caused by LSP is revealed. The results indicate that the material’s fatigue life initially increases and subsequently declines with the rising pulse energy. At the optimal pulse energy condition, the laser-shocked specimen demonstrates a 126% increase in fatigue life relative to the untreated specimen, which is accompanied by the higher residual compressive stress along the depth. Meanwhile, the grains become more refined with a uniform size change gradient, and the β phase content drops from 4.1% to 2.2%. Notably, regions with <$\stackrel{-}{1}$2$\stackrel{\mathrm{-}}{1}$0> crystal orientation can be selectively achieved. With the favorable <$\stackrel{\mathrm{-}}{1}$2$\stackrel{\mathrm{-}}{1}$0> slip direction orthogonal to the applied fatigue loading axis, the generation and propagation of dislocations are effectively constrained, thereby significantly enhancing the material’s fatigue performance. The stress distribution and fatigue life in models with different grain sizes and phase contents are further analyzed by the CPFE method, showing good consistency with the experimental results. Theoretically, the excessively high pulse energy causes the transient temperature (1769 °C) to surpass the melting point (1660 °C), which can affect the recrystallization structure and stress distribution. Full article

Hip joint implants are among the most prevalent types of medical implants utilized for the replacement of damaged joints. The utilization of modern implant materials, such as cobalt–chromium alloys, stainless steel, titanium, and other titanium alloys, is accompanied by challenges, including the toxicity of certain elements (e.g., aluminum, vanadium, nickel) and excessive Young’s modulus, which adversely impact biomechanical compatibility. A mismatch between the stiffness of the implant material and the bone tissue, known as stress shielding, can lead to adverse outcomes such as bone resorption and implant loosening. Recent studies have shifted the focus to β-titanium alloys due to their exceptional biocompatibility, corrosion resistance, and low Young’s modulus, which is close to the Young’s modulus of bone tissue (10–30 GPa). In this study, the microstructure, mechanical properties, and phase stability of the Ti-38Zr-11Nb alloy were investigated. Energy dispersion spectrometry was employed to confirm the homogeneous distribution of Ti, Zr, and Nb in the alloy. A subsequent microstructural analysis revealed the presence of elongated β-grains subsequent to rolling and quenching. Furthermore, grinding contributed to the process of recrystallization and the formation of subgrains. X-ray diffraction analysis confirmed the presence of a stable β-phase under any heat treatment conditions, which can be explained by the use of Nb as a β-stabilizer and Zr as a neutral element with a weak β-stabilizing effect in the presence of other β-stabilizers. Furthermore, the modulus of elasticity, as determined by tensile testing, exhibited a decline from 85 GPa to 81 GPa after annealing. Mechanical tests demonstrated a substantial enhancement in tensile strength (from 529 MPa to 628 MPa) concurrent with a 32% reduction in elongation to fracture of the samples. These alterations are attributed to microstructural transformations, including the formation of subgrains and the rearrangement of dislocations. This study’s findings suggest that the Ti-38Zr-11Nb alloy has potential as a material of choice due to its lower Young’s modulus compared to traditional materials and its stable β-phase, which enhances the implant’s durability and reduces the risk of brittle phases forming over time. This study demonstrates that the corrosion resistance of titanium grade 2 and Ti-38Zr-11Nb is comparable. The material in question exhibited no evidence of cytotoxic activity in the context of mammalian cells. Full article

With superior manufacturing freedom capability, Selective Laser Melting (SLM) technology is capable of fabricating high-strength Ti-6Al-2Zr-1Mo-1V (TA15) complex titanium alloy parts, thereby finding extensive applications in the aerospace sector. This paper primarily investigates the influence of process parameters on the relative density, microstructure, and mechanical properties of SLMed TA15 under conditions of similar laser linear energy density. The results indicate that the laser linear energy density significantly affects the single-track morphology of SLMed TA15; excessive energy density leads to keyhole defects, while insufficient energy density causes balling phenomena, resulting in discontinuous clad tracks. When the laser linear energy density is appropriate, the scanning spacing affects the forming density of the parts, with both excessively large and small spacings having adverse effects. With a fixed scanning spacing of 100 μm, high-density samples can be produced within a suitable range of linear energy density. However, when the laser linear energy density is comparable, a lower scanning speed leads to heat accumulation, causing in situ decomposition of the α’ martensite and the formation of coarser α + β phases, which reduces strength and hardness but improves plasticity. At a laser power of 90 W, a scanning speed of 400 mm/s, and a scanning spacing of 100 μm, the specimen exhibits a tensile strength of 1233 MPa and an elongation of 8.4%, achieving relatively excellent comprehensive properties. Full article

A near-α titanium alloy was fabricated using spark plasma sintering (SPS) to investigate the effects of sintering temperature on its relative density, microstructure, and mechanical properties. The relative density increased significantly with temperature, reaching 94.56%, 99.91%, and 99.99% at 850 °C, 900 °C, and 1000 °C, respectively. At 850 °C, the alloy contained numerous pores, leading to low density, while at 900 °C, full densification was achieved, resulting in a bimodal microstructure comprising 20% primary α phase (average size: 2.74 μm) and 80% transformed β phase (average lamellar width: 0.88 μm). Nanoscale equiaxed α phase (375 nm) and dispersed nanoscale β phase (80 nm) were observed within the lamellar structure. A distinct L-phase interfacial layer (50–100 nm) was identified at the α/β interfaces with a specific orientation relationship. At 1000 °C, the microstructure transformed into a fully lamellar structure with wider lamellae (1.99 μm), but mechanical properties declined due to coarsening. The alloy sintered at 900 °C exhibited the best properties, with a tensile strength of 989 ± 10 MPa at room temperature and 632 ± 10 MPa at 600 °C, along with elongations of 9.2 ± 0.5% and 13.0 ± 0.5%, respectively. These results highlight the importance of optimizing sintering temperature to balance densification and microstructural refinement for enhanced mechanical performance. Full article

A novel coupled processing method (PDCT) that associated deep cryogenic treatment (DCT) with a high pulsed magnetic field (PMT) was investigated to improve the performance of an as-cast TC4 aero-titanium alloy. Through XRD, SEM, TEM, EBSD, and a properties test, its microstructure and tensile properties and their relationship were investigated. The results show that in comparison with the untreated samples, in the PDCT alloys, the amount of nano-sized precipitates and dislocation density are increased, and this phenomenon is characterized by their combed dislocation morphology. The grain sizes are refined and rounded, and the deformed grains are enhanced, together with the enhancement of low-angle grain boundaries in grains and the transformation from the β phase to the α phase. The (112) crystal orientation is apparently strengthened. The tensile strength, elongation, and fracture energy of the optimized PDCT sample are 921.4 MPa, 7.6% and 5.47 × 10⁷ J/m³, which increased by 4.9%, 28.8% and 80.5% compared with the untreated sample, respectively. The tensile fracture exhibits rheological deformation along the phase boundaries. The strength–toughness mechanisms are mainly attributed to the texture, precipitation, dislocation and fine grain strengthening, which stem from the cold contraction and lattice distortion of DCT and the main magneto-plasticity effect of PMT, together with their coupling effects. Full article

This study involved the preparation of dense Ti-10wt.%Mo alloys using selective laser melting (SLM) with a powder combination of pure titanium (Ti) and pure molybdenum (Mo). Integrating temperature stress numerical simulations and actual data elucidates the correlation between linear laser energy density and residual stress. The impact of linear energy density on the surface roughness, densification behavior, microstructural development, and mechanical properties of SLM-processed Ti-10Mo components was also examined. As linear energy density diminished from 0.125 J/mm to 0.233 J/mm, surface roughness reduced from 18.2 μm to 4.4 μm, while relative compactness increased from 94.9% to 99.8%, respectively. It is necessary to reduce the friction between the puncture needle or implant needle and human tissue, enhancing comfort and precision. The microstructural investigation revealed that SLM-processed Ti-10Mo alloys consist of a phase combination of hexagonal tight-packed (hcp) α-Ti and body-centered cubic (bcc) β-Ti, with heterogeneous conchoidal microstructures found in the samples. Furthermore, as the laser energy input increased, Mo powder particles were mostly fully melted, leading to a significant rise in the microhardness value. The as-built Ti-10Mo alloys exhibited a high ultimate tensile strength of 860 MPa and an elongation of 32.9% at a linear laser energy density of 0.15 J/mm, with the fracture morphology indicating a mixed fracture mode mostly characterized by ductile fracture. This research can enhance the prospective bio-application of Ti-Mo alloys. Full article

The development of beta titanium alloys with biocompatible elements to replace Al and V is a subject of significant interest in the biomedical industry. This approach aims to enhance biocompatibility and mitigate potential cytotoxic effects associated with traditional alloying elements. In this work, Ti–xNb–ySi alloys were produced using powder metallurgy, with x of 35, 40, and 45 wt.%, and y of 0.10, 0.35, and 0.60% wt.%, using a $3^2$ experimental design. Milling was used to mix and disperse the powders, followed by cold pressing, sintering, and heat treatment. Nb was the main element used to stabilize the β phase, and Si was used to form Si precipitates, although Si also exhibits a β-stabilizing effect. It was found that an increase from 0.10 to 0.35 wt.% of Si improved relative density, with no benefits observed at 0.60 wt.% Si. Electron microscopy showed the presence of β phase grains, and grains with β + α intragranular structures and precipitates. Increasing Nb content resulted in a decrease in ultimate tensile strength while increasing Si content from 0.10% to 0.35 wt.% exhibited the opposite effect. Full article

TB18 is a newly developed high-strength metastable β-titanium alloy, commonly used in aerospace structural materials, which demands high mechanical performance. By altering the alloy’s microstructure, heat treatment can affect its mechanical characteristics. The alloy was solution treated for one to four hours at 870 °C in order to examine the impact of solution treatment duration. Using X-ray diffraction (XRD) and scanning electron microscopy (SEM), the effects of solution treatment time on the β-phase grain size and its effect on stress distribution during tensile testing were examined. The findings showed that stress concentration during the tensile process was successfully decreased by refining the β-phase grain size. Sample solutions treated for two hours at 870 °C were then aged at various temperatures (510 °C, 520 °C, 530 °C, and 540 °C) to examine the impact of aging temperature. While the mass proportion of the α-phase first climbed and subsequently declined, reaching its maximum at 530 °C, the size of the α-phase increased monotonically as the aging temperature increased. The varies of mass fraction is associated with how the aging temperature affects α-phase nucleation. Tensile studies on TB18 alloy aged at various temperatures showed that while the alloy’s ductility reduced, its strength increased as the aging temperature rose. The Hall-Petch relationship explains this tendency. Full article