Bioprinting 2021

A special issue of Micromachines (ISSN 2072-666X). This special issue belongs to the section "B2: Biofabrication and Tissue Engineering".

Deadline for manuscript submissions: closed (30 June 2021) | Viewed by 4399

Special Issue Editor

School of Sustainable Design Engineering, University of Prince Edward Island, 550 University Avenue, Charlottetown, PEI C1A 4P3, Canada
Interests: bioprinting; microfluidics; drop-based systems; electrohydrodynamics

Special Issue Information

Dear Colleagues,

3D bioprinting is defined as the development of complex living and non-living biological constructs from materials including living cells, extracellular matrices, and biomaterials (also known as bioiniks). In the short term, bioprinting technology is essential for developing highly predictive living tissue-based technologies for drug discovery, and complex in vitro models of human diseases. In the long term, bioprinting can potentially contribute to the development of novel biotechnologies for organ transplants, gene therapy, smart drug delivery systems and biomimetic devices. Consequently, the wide range of potential applications of bioprinting strongly suggests that this emerging technology will become a new paradigm for 21st century manufacturing and biotechnology.

This special issue covers all aspects of 3D bioprinting technology with emphasis on the recent advances in the development and optimization of printhead technologies and bioinks. Topics covered include but not limited to printhead technogies, bioinks, pre-bioprinting, post-bioprinting, biofabrication window, emerging applications of 3D bioprinting technology.

Dr. Ali Ahmadi
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Micromachines is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • 3D printing prtintheads
  • Bioinks
  • Scaffolds
  • Pre-bioprinting
  • Post-bioprinting
  • Biofabrication window

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (1 paper)

Order results
Result details
Select all
Export citation of selected articles as:

Research

18 pages, 4035 KiB  
Article
Shape Fidelity of 3D-Bioprinted Biodegradable Patches
by Mikail Temirel, Christopher Hawxhurst and Savas Tasoglu
Micromachines 2021, 12(2), 195; https://doi.org/10.3390/mi12020195 - 13 Feb 2021
Cited by 16 | Viewed by 3826
Abstract
There is high demand in the medical field for rapid fabrication of biodegradable patches at low cost and high throughput for various instant applications, such as wound healing. Bioprinting is a promising technology, which makes it possible to fabricate custom biodegradable patches. However, [...] Read more.
There is high demand in the medical field for rapid fabrication of biodegradable patches at low cost and high throughput for various instant applications, such as wound healing. Bioprinting is a promising technology, which makes it possible to fabricate custom biodegradable patches. However, several challenges with the physical and chemical fidelity of bioprinted patches must be solved to increase the performance of patches. Here, we presented two hybrid hydrogels made of alginate-cellulose nanocrystal (CNC) (2% w/v alginate and 4% w/v CNC) and alginate-TEMPO oxidized cellulose nanofibril (T-CNF) (4% w/v alginate and 1% w/v T-CNC) via ionic crosslinking using calcium chloride (2% w/v). These hydrogels were rheologically characterized, and printing parameters were tuned for improved shape fidelity for use with an extrusion printing head. Young’s modulus of 3D printed patches was found to be 0.2–0.45 MPa, which was between the physiological ranges of human skin. Mechanical fidelity of patches was assessed through cycling loading experiments that emulate human tissue motion. 3D bioprinted patches were exposed to a solution mimicking the body fluid to characterize the biodegradability of patches at body temperature. The biodegradation of alginate-CNC and alginate-CNF was around 90% and 50% at the end of the 30-day in vitro degradation trial, which might be sufficient time for wound healing. Finally, the biocompatibility of the hydrogels was tested by cell viability analysis using NIH/3T3 mouse fibroblast cells. This study may pave the way toward improving the performance of patches and developing new patch material with high physical and chemical fidelity for instant application. Full article
(This article belongs to the Special Issue Bioprinting 2021)
Show Figures

Figure 1

Back to TopTop