Membranes

2024

Jump to: 2023, 2022

13 pages, 2016 KiB

Open AccessArticle

Towards the Optimization of a Photovoltaic/Membrane Distillation System for the Production of Pure Water

by Dufei Fang, Damian M. Amiruddin, Imin Kao, Devinder Mahajan, Xuming Chen and Benjamin S. Hsiao

Membranes 2024, 14(5), 110; https://doi.org/10.3390/membranes14050110 - 13 May 2024

Viewed by 1383

Abstract

The production of pure water plays a pivotal role in enabling sustainable green hydrogen production through electrolysis. The current industrial approach for generating pure water relies on energy-intensive techniques such as reverse osmosis. This study unveils a straightforward method to produce pure water, [...] Read more.

The production of pure water plays a pivotal role in enabling sustainable green hydrogen production through electrolysis. The current industrial approach for generating pure water relies on energy-intensive techniques such as reverse osmosis. This study unveils a straightforward method to produce pure water, employing real-world units derived from previously simulated and developed laboratory devices. This demonstrated system is cost-effective and boasts low energy consumption, utilizing membrane distillation (MD) driven by the waste heat harnessed from photovoltaic (PV) panels. In a previous study, modeling simulations were conducted to optimize the multi-layered MD system, serving as a blueprint for the construction of prototype devices with a suitable selection of materials, enabling the construction of field-testable units. The most efficient PV-MD device, featuring evaporation and condensation zones constructed from steel sheets and polytetrafluoroethylene (PTFE) membranes, is capable of yielding high-purity water with conductivity levels below 145 μS with high flux rates. Full article

► Show Figures

Figure 1

2023

Jump to: 2024, 2022

16 pages, 3601 KiB

Open AccessOpinion

Potential of the Novel Slot Blot Method with a PVDF Membrane for Protein Identification and Quantification in Kampo Medicines

by Takanobu Takata, Togen Masauji and Yoshiharu Motoo

Membranes 2023, 13(12), 896; https://doi.org/10.3390/membranes13120896 - 1 Dec 2023

Cited by 4 | Viewed by 2380

Abstract

Kampo is a Japanese traditional medicine modified from traditional Chinese medicine. Kampo medicines contain various traditional crude drugs with unknown compositions due to the presence of low-molecular-weight compounds and proteins. However, the proteins are generally rare and extracted with high-polarity solvents such as [...] Read more.

Kampo is a Japanese traditional medicine modified from traditional Chinese medicine. Kampo medicines contain various traditional crude drugs with unknown compositions due to the presence of low-molecular-weight compounds and proteins. However, the proteins are generally rare and extracted with high-polarity solvents such as water, making their identification and quantification difficult. To develop methods for identifying and quantifying the proteins in Kampo medicines, in the current study we employ previous technology (e.g., column chromatography, electrophoresis, and membrane chromatography), focusing on membrane chromatography with a polyvinylidene difluoride (PVDF) membrane. Moreover, we consider slot blot analysis based on the principle of membrane chromatography, which is beneficial for analyzing the proteins in Kampo medicines as the volume of the samples is not limited. In this article, we assess a novel slot blot method developed in 2017 and using a PVDF membrane and special lysis buffer to quantify advanced glycation end products-modified proteins against other slot blots. We consider our slot blot analysis superior for identifying and quantifying proteins in Kampo medicines compared with other methods as the data obtained with our novel slot blot can be shown with both error bars and the statistically significant difference, and our operation step is simpler than those of other methods. Full article

► Show Figures

Figure 1

19 pages, 2459 KiB

Open AccessArticle

Theoretical and Experimental Analysis of Osmotically Assisted Reverse Osmosis for Minimum Liquid Discharge

by Jaehyun Ju, Seoyeon Lee, Yusik Kim, Hyeongrak Cho and Sangho Lee

Membranes 2023, 13(10), 814; https://doi.org/10.3390/membranes13100814 - 27 Sep 2023

Cited by 6 | Viewed by 2506

Abstract

Osmotically assisted reverse osmosis (OARO) is an innovative process that shows promising potential in the treatment of brine produced by conventional reverse osmosis (RO) systems. This study presents a theoretical and experimental analysis of the OARO process, focusing on its application to achieve [...] Read more.

Osmotically assisted reverse osmosis (OARO) is an innovative process that shows promising potential in the treatment of brine produced by conventional reverse osmosis (RO) systems. This study presents a theoretical and experimental analysis of the OARO process, focusing on its application to achieve minimum liquid discharge (MLD). This theoretical analysis includes the development of a mathematical model to describe the transport phenomena occurring during OARO. By considering mass balance equations coupled with transport equations, the theoretical model allows for the simulation of a full-scale system consisting of a single-stage RO and a four-stage OARO. Experimental investigations are also conducted to validate the theoretical model and to evaluate the performance of the OARO process. A laboratory-scale OARO system is designed and operated using a synthetic RO brine. Various operating conditions, including applied pressure, feed concentration, and draw concentration, are varied to investigate their effects on process performance. The experimental results demonstrate the feasibility of OARO as an MLD solution and also validate the predictions of the theoretical model, confirming its reliability for process optimization and design. The results of the theoretical analysis show that OARO has the potential to significantly improve water recovery compared to conventional RO. Based on the simulation, the optimal operating conditions are explored, leading to a significant reduction (up to 89%) in the volume of brine discharge. Full article

► Show Figures

Figure 1

10 pages, 3618 KiB

Open AccessArticle

Study on ZrSi₂ as a Candidate Material for Extreme Ultraviolet Pellicles

by Seong Ju Wi, Won Jin Kim, Haneul Kim, Dongmin Jeong, Dong Gi Lee, Jaehyuck Choi, Sang Jin Cho, Lan Yu and Jinho Ahn

Membranes 2023, 13(8), 731; https://doi.org/10.3390/membranes13080731 - 14 Aug 2023

Cited by 2 | Viewed by 2240

Abstract

An extreme ultraviolet (EUV) pellicle is an ultrathin membrane at a stand-off distance from the reticle surface that protects the EUV mask from contamination during the exposure process. EUV pellicles must exhibit high EUV transmittance, low EUV reflectivity, and superior thermomechanical durability that [...] Read more.

An extreme ultraviolet (EUV) pellicle is an ultrathin membrane at a stand-off distance from the reticle surface that protects the EUV mask from contamination during the exposure process. EUV pellicles must exhibit high EUV transmittance, low EUV reflectivity, and superior thermomechanical durability that can withstand the gradually increasing EUV source power. This study proposes an optimal range of optical constants to satisfy the EUV pellicle requirements based on the optical simulation results. Based on this, zirconium disilicide (ZrSi₂), which is expected to satisfy the optical and thermomechanical requirements, was selected as the EUV pellicle candidate material. An EUV pellicle composite comprising a ZrSi₂ thin film deposited via co-sputtering was fabricated, and its thermal, optical, and mechanical properties were evaluated. The emissivity increased with an increase in the thickness of the ZrSi₂ thin film. The measured EUV transmittance (92.7%) and reflectivity (0.033%) of the fabricated pellicle satisfied the EUV pellicle requirements. The ultimate tensile strength of the pellicle was 3.5 GPa. Thus, the applicability of the ZrSi₂ thin film as an EUV pellicle material was verified. Full article

► Show Figures

Figure 1

25 pages, 2438 KiB

Open AccessEditor’s ChoiceReview

Forward Osmosis Application for the Removal of Emerging Contaminants from Municipal Wastewater: A Review

by Mónica Salamanca, Mar Peña, Antonio Hernandez, Pedro Prádanos and Laura Palacio

Membranes 2023, 13(7), 655; https://doi.org/10.3390/membranes13070655 - 10 Jul 2023

Cited by 9 | Viewed by 3149

Abstract

Forward osmosis (FO) has attracted special attention in water and wastewater treatment due to its role in addressing the challenges of water scarcity and contamination. The presence of emerging contaminants in water sources raises concerns regarding their environmental and public health impacts. Conventional [...] Read more.

Forward osmosis (FO) has attracted special attention in water and wastewater treatment due to its role in addressing the challenges of water scarcity and contamination. The presence of emerging contaminants in water sources raises concerns regarding their environmental and public health impacts. Conventional wastewater treatment methods cannot effectively remove these contaminants; thus, innovative approaches are required. FO membranes offer a promising solution for wastewater treatment and removal of the contaminants in wastewater. Several factors influence the performance of FO processes, including concentration polarization, membrane fouling, draw solute selection, and reverse salt flux. Therefore, understanding and optimizing these factors are crucial aspects for improving the efficiency and sustainability of the FO process. This review stresses the need for research to explore the potential and challenges of FO membranes to meet municipal wastewater treatment requirements, to optimize the process, to reduce energy consumption, and to promote scalability for potential industrial applications. In conclusion, FO shows promising performance for wastewater treatment, dealing with emerging pollutants and contributing to sustainable practices. By improving the FO process and addressing its challenges, we could contribute to improve the availability of water resources amid the global water scarcity concerns, as well as contribute to the circular economy. Full article

► Show Figures

Graphical abstract

25 pages, 7087 KiB

Open AccessArticle

Highly Efficient Cationic/Anionic Cellulose Membranes for Removal of Cr(VI) and Pb(II) Ions

by Lu Liu, Hongyang Ma, Madani Khan and Benjamin S. Hsiao

Membranes 2023, 13(7), 651; https://doi.org/10.3390/membranes13070651 - 6 Jul 2023

Cited by 1 | Viewed by 1626

Abstract

To achieve high throughput, low-pressure drops, and high adsorption capacity of Cr(VI) and Pb(II) in industrial wastewater treatment, cellulose membranes containing cationic and anionic groups were fabricated, respectively. In this process, cost-effective cotton fabrics were oxidized using sodium periodate, followed by quaternary ammonium [...] Read more.

To achieve high throughput, low-pressure drops, and high adsorption capacity of Cr(VI) and Pb(II) in industrial wastewater treatment, cellulose membranes containing cationic and anionic groups were fabricated, respectively. In this process, cost-effective cotton fabrics were oxidized using sodium periodate, followed by quaternary ammonium or sulfonation modifications. The chemical composition, surface morphology, and thermal and mechanical properties of the cellulose membranes were investigated by ATR-FTIR, solid-state NMR, SEM, TGA, and tensile experiments. Quaternary ammonium, aldehyde, and sulfonate groups were distributed on the cationic/anionic cellulose fibers as adsorption sites, which issue remarkable adsorption capability to the cellulose membranes. The highly toxic Cr(VI) and Pb(II) ions were used to challenge the adsorption capacity of the cationic and anionic cellulose membranes, respectively. The maximum adsorption capacities of Cr(VI) and Pb(II) ions were 61.7 and 63.7 mg/g, respectively, suggested by Langmuir isotherms, kinetics, and thermodynamics in the static experiments. The dynamic adsorption capability of cationic cellulose membranes against Cr(VI) ions was determined and compared with that of commercially available anionic-exchange membranes. Spiral wound filtration cartridges were fabricated by cationic and anionic cellulose membranes, respectively, and were used to adsorb Cr(VI) and Pb(II) from lab-made wastewater, respectively. The cationic cellulose cartridge can purify 4.4 L of wastewater containing 1.0 mg/L of Cr(VI) ions with a 100% removal ratio, while the pressure drop was retained at 246 Pa. Similarly, the anionic cellulose cartridge exhibited even more impressive adsorption capability; the removal ratio against Pb(II) was 99% when 8.6 L of 1.0 mg/L of Pb(II) ions containing wastewater was treated, and the pressure drop was retained at 234 Pa. A composite cartridge fabricated by the integration of cationic and anionic cellulose membranes was successfully employed to purify the wastewater containing Cr(VI) and Pb(II) simultaneously. The possible adsorption mechanism was proposed, and the recycling ability of the cellulose membranes was also discussed. Full article

► Show Figures

Figure 1

14 pages, 4207 KiB

Open AccessArticle

Fouling Control Strategies for High Concentrated Liquid Desiccants Concentrating Using Membrane Distillation

by Seonguk Ha, Jieun Lee, Seongeom Jeong and Sanghyun Jeong

Membranes 2023, 13(2), 222; https://doi.org/10.3390/membranes13020222 - 10 Feb 2023

Cited by 2 | Viewed by 1667

Abstract

Air conditioning using a liquid desiccant (LD) is an energy-efficient air purification and cooling system. However, high energy is required to concentrate or regenerate the LD. This study aimed to investigate the characteristics of membrane fouling in more detail and determine control strategies [...] Read more.

Air conditioning using a liquid desiccant (LD) is an energy-efficient air purification and cooling system. However, high energy is required to concentrate or regenerate the LD. This study aimed to investigate the characteristics of membrane fouling in more detail and determine control strategies for LD concentrating using membrane distillation (MD). Two different LDs—lithium chloride (LiCl) and potassium formate (HCOOK)—were used. Because LDs require high concentrations by nature (i.e., 40 wt% for LiCl and 70 wt% for HCOOK), the concentration was started from half of those concentrations. This resulted in a flux decline with severe membrane fouling during the concentration using MD. Different membrane fouling mechanisms were also observed, depending on the LD type. Three different physical membrane fouling control methods, including water flushing (WF), air backwashing (AB), and membrane spacer (SP), were introduced. Results showed that WF was the most effective. Both AB and SP showed a marginal change to no cleaning; however, an initial flux with SP was about 1.5 times higher than no cleaning. Therefore, WF combined with the SP could maintain a high flux and a low fouling propensity in the treatment of a high-concentration solution using MD. Full article

► Show Figures

Figure 1

19 pages, 10809 KiB

Open AccessArticle

Low Fouling Nanostructured Cellulose Membranes for Ultrafiltration in Wastewater Treatment

by Ritika Joshi, Nilay Sebat, Kai Chi, Madani Khan, Ken I. Johnson, Abdulrahman G. Alhamzani, M. A. Habib, Tom Lindstrom and Benjamin S. Hsiao

Membranes 2023, 13(2), 147; https://doi.org/10.3390/membranes13020147 - 23 Jan 2023

Cited by 12 | Viewed by 2794

Abstract

Ultrafiltration (UF) is a common technique used in wastewater treatments. However, the issue of membrane fouling in UF can greatly hinder the effectiveness of the treatments. This study demonstrated a low-fouling composite cellulose membrane system based on microfibrillated cellulose (MFC) and silica nanoparticle [...] Read more.

Ultrafiltration (UF) is a common technique used in wastewater treatments. However, the issue of membrane fouling in UF can greatly hinder the effectiveness of the treatments. This study demonstrated a low-fouling composite cellulose membrane system based on microfibrillated cellulose (MFC) and silica nanoparticle additives. The incorporation of ‘non-spherical’ silica nanoparticles was found to exhibit better structural integration in the membrane (i.e., minimal aggregation of silica nanoparticles in the membrane scaffold) as compared to spherical silica. The resulting composite membranes were tested for UF using local wastewater, where the best-performing membrane exhibited higher permeation flux than commercial polyvinylidene difluoride (PVDF) and polyether sulfone (PES) membranes while maintaining a high separation efficiency (~99.6%) and good flux recovery ratio (>90%). The analysis of the fouling behavior using different models suggested that the processes of cake layer formation and pore-constriction were probably two dominant fouling mechanisms, likely due to the presence of humic substances in wastewater. The demonstrated cellulose composite membrane system showed low-fouling and high restoration capability by a simple hydraulic cleaning method due to the super hydrophilic nature of the cellulose scaffold containing silica nanoparticles. Full article

► Show Figures

Figure 1

2022

Jump to: 2024, 2023

14 pages, 9249 KiB

Open AccessArticle

Effect of Electrode Morphology on Performance of Ionic Actuators Based on Vat Photopolymerized Membranes

by Oleg S. Morozov, Anna V. Ivanchenko, Sergey S. Nechausov and Boris A. Bulgakov

Membranes 2022, 12(11), 1110; https://doi.org/10.3390/membranes12111110 - 7 Nov 2022

Cited by 1 | Viewed by 1667

Abstract

Bucky gel electrodes are composed of morphology-determining polyvinylidene difluoride (PVDF) filled with carbon nanotubes (CNT). The electrodes are commonly fabricated via the casting of a CNT dispersion containing PVDF and ionic liquid. In this study, several pore-forming additives such as polyethylene glycol (PEG), [...] Read more.

Bucky gel electrodes are composed of morphology-determining polyvinylidene difluoride (PVDF) filled with carbon nanotubes (CNT). The electrodes are commonly fabricated via the casting of a CNT dispersion containing PVDF and ionic liquid. In this study, several pore-forming additives such as polyethylene glycol (PEG), dibutyl phthalate (DBP), and the common ionic liquid BMIMBF4 were used to control the morphology of the bucky gel electrodes. The crystalline phase type and content of PVDF in the electrodes were determined by FT-IR and DSC, respectively. SEM revealed a sponge-like structure in the case of the use of BMIMBF4 and a spherulite structure if PEG and DBP were used as additives. A strong influence of morphology on the anisotropic increase in the volume of electrodes upon impregnation with electrolyte was observed. The PEG-based electrode elongated more than the others, while the BMIMBF4-based electrode thickened to a greater extent. Ionic actuators were fabricated to experimentally reveal the effect of electrode morphology on their electromechanical efficiency. A high-precision vat photopolymerization technique was used to fabricate identical ionic membranes and minimize their influence on the properties of the actuators. The electrodes were characterized by the same porosity and electrical capacitance, while the actuators differ significantly in performance. As a result, a simple method of using pore-forming additives made it possible to increase the maximum deformation of bucky gel ionic actuators by 1.5 times by changing the morphology of the electrodes. Full article

► Show Figures

Figure 1

30 pages, 12346 KiB

Open AccessArticle

Failure Mechanisms of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ Membranes after Pilot Module Operation

by Simone Herzog, Chao Liu, Nicolas Nauels, Anke Kaletsch and Christoph Broeckmann

Membranes 2022, 12(11), 1093; https://doi.org/10.3390/membranes12111093 - 3 Nov 2022

Cited by 2 | Viewed by 1455

Abstract

The step from the testing of oxygen transport membranes on a lab scale to long-term operation on a large scale is a challenge. In a previous study, membrane failure was observed at defined positions of one end of the cooled tubular Ba_0.5 [...] Read more.

The step from the testing of oxygen transport membranes on a lab scale to long-term operation on a large scale is a challenge. In a previous study, membrane failure was observed at defined positions of one end of the cooled tubular Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ membranes after an emergency shutdown. To understand the failure mechanisms, strength degradation and transient stress distribution were investigated by brittle-ring tests and finite element simulations, respectively. A 15% decrease in the characteristic strength of 162 MPa was proven after aging at 850 °C and was attributed to grain coarsening. The reduction in characteristic strength after thermal shock ranged from 5 to 90% depending on the cooling rates, and from 5 to 40% after the first and 20th soft thermal cycling. Simulations indicated the chemical strains induced by a 10-bar feed air and 50 mbar permeate pressure, which caused tensile stresses of up to 70 MPa at the outer surface. These stresses relaxed to 43 MPa by creep within a 1000 h operation. A remaining local stress maximum seemed to be responsible for the fracture. It evolved near the experimentally observed fracture position during a 1000 h permeation and exceeded the temperature and time-dependent strength. The maximum stress was formed by a chemical strain at temperatures above 500 °C but effective creep relaxation needed temperatures above 750 °C. Full article

► Show Figures

Figure 1

17 pages, 2926 KiB

Open AccessArticle

Reduced Low–Pressure Membrane Fouling by Inline Coagulation Pretreatment for a Colored River Water

by Joseph D. Ladouceur and Roberto M. Narbaitz

Membranes 2022, 12(11), 1028; https://doi.org/10.3390/membranes12111028 - 22 Oct 2022

Cited by 3 | Viewed by 1915

Abstract

Drinking water treatment (DWT) using low–pressure membranes (LPM) has become increasingly popular due to their many reported advantages compared to conventional technologies. Productivity decline due to fouling has prevented LPMs from becoming the technology of choice in DWT, however, coagulation pretreatment either with [...] Read more.

Drinking water treatment (DWT) using low–pressure membranes (LPM) has become increasingly popular due to their many reported advantages compared to conventional technologies. Productivity decline due to fouling has prevented LPMs from becoming the technology of choice in DWT, however, coagulation pretreatment either with or without particle separation mitigates fouling phenomena. The effectiveness of coagulation/flocculation/sedimentation (CF–S), coagulation/flocculation/dissolved air flotation (CF–DAF), and inline coagulation (CF–IN) as technologies for pretreatment of feed water has rarely been investigated using the same water source. In this study, CF–S, CF–DAF, and CF–IN are directly compared as pretreatment of a tubular multi–channeled ultrafiltration (UF) membrane using the same highly colored river water. Three–day long filtration tests were performed using an automated bench–scale filtration apparatus with an inside–out configuration. Although CF–DAF had the greatest removal of dissolved organic matter (DOM) and hydrophobic organics, CF–S pretreatment resulted in a similar level of total fouling. Compared to CF–DAF and CF–S, CF–IN pretreatment resulted in lower fouling. The hydraulic and chemical reversibility of CF–IN fouling was seen to be strongly influenced by the feed water zeta potential, suggesting the importance of floc electrostatic and morphological characteristics on inline coagulation performance. Full article

► Show Figures

Graphical abstract

20 pages, 6649 KiB

Open AccessArticle

Modelling Analysis of a Membrane-Based Fresh Air Processing System

by Sebastian Englart and Krzysztof Rajski

Membranes 2022, 12(10), 1022; https://doi.org/10.3390/membranes12101022 - 20 Oct 2022

Cited by 5 | Viewed by 1831

Abstract

The current standard of residential buildings is based on well-insulated and airtight construction as an effective way to reduce primary energy consumption. On the other hand, this intensifies the issue of the indoor air quality. In this paper, the applicability of a hybrid [...] Read more.

The current standard of residential buildings is based on well-insulated and airtight construction as an effective way to reduce primary energy consumption. On the other hand, this intensifies the issue of the indoor air quality. In this paper, the applicability of a hybrid dehumidification/evaporative cooling system for the processing and supply of fresh air is evaluated. The proposed novel system employs cross-flow hollow-fiber membrane modules. To provide a better insight into this novel approach, the system’s performance is numerically investigated using a validated mathematical model. The proposed fresh air processing system provides supply air parameters in or close to the summer comfort range. The analyzed system is characterized by a high coefficient of performance (COP) of up to 33.2 at an outdoor air temperature in the range of 30 °C to 38 °C and a humidity ratio in the range of 8 g/kg to 14 g/kg. Moreover, a temperature difference of up to 9.7 °C can be obtained after the two-stage membrane processing and the mixing process. Full article

► Show Figures

Figure 1

15 pages, 4643 KiB

Open AccessArticle

Synthesis and Characterization of Silica–Tantala Microporous Membranes for Gas Separations Fabricated Using Chemical Vapor Deposition

by Sean-Thomas B. Lundin, Hongsheng Wang and S. Ted Oyama

Membranes 2022, 12(9), 889; https://doi.org/10.3390/membranes12090889 - 16 Sep 2022

Cited by 2 | Viewed by 2148

Abstract

Composite membranes consisting of microporous tantalum-doped silica layers supported on mesoporous alumina substrates were fabricated using chemical vapor deposition (CVD) in both thermal decomposition and counter-flow oxidative deposition modes. Tetraethyl orthosilicate (TEOS) was used as the silica precursor and tantalum (V) ethoxide (TaEO) [...] Read more.

Composite membranes consisting of microporous tantalum-doped silica layers supported on mesoporous alumina substrates were fabricated using chemical vapor deposition (CVD) in both thermal decomposition and counter-flow oxidative deposition modes. Tetraethyl orthosilicate (TEOS) was used as the silica precursor and tantalum (V) ethoxide (TaEO) as the tantalum source. Amounts of TaEO from 0 mol% to 40 mol% were used in the CVD gas mixture and high H₂ permeances above 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ were obtained for all conditions. Close examination was made of the H₂/CH₄ and O₂/CH₄ selectivities due to the potential use of these membranes in methane reforming or partial oxidation of methane applications. Increasing deposition temperature correlated with increasing H₂/CH₄ selectivity at the expense of O₂/CH₄ selectivity, suggesting a need to optimize membrane synthesis for a specific selectivity. Measured at 400 °C, the highest H₂/CH₄ selectivity of 530 resulted from thermal CVD at 650 °C, whereas the highest O₂/CH₄ selectivity of 6 resulted from thermal CVD at 600 °C. The analysis of the membranes attempted by elemental analysis, X-ray photoelectron spectroscopy, and X-ray absorption near-edge spectroscopy revealed that Ta was undetectable because of instrumental limitations. However, the physical properties of the membranes indicated that the Ta must have been present at least at dopant levels. It was found that the pore size of the resultant membranes increased from 0.35 nm for pure Si to 0.37 nm for a membrane prepared with 40 mol% Ta. Similarly, an increase in Ta in the feed resulted in an increase in O₂/CH₄ selectivity at the expense of H₂/CH₄ selectivity. Additionally, it resulted in a decrease in hydrothermal stability, with the membranes prepared with higher Ta suffering greater permeance and selectivity declines during 96 h of exposure to 16 mol% H₂O in Ar at 650 °C. Full article

► Show Figures

Graphical abstract

18 pages, 3722 KiB

Open AccessArticle

Effect of Drying Temperature on Physical, Chemical, and Antioxidant Properties of Ginger Oil Loaded Gelatin-Sodium Alginate Edible Films

by Ahmed Al-Harrasi, Saurabh Bhatia, Mohammed Said Al-Azri, Sana Ullah, Asim Najmi, Mohammed Albratty, Abdulkarim M. Meraya, Syam Mohan and Mohammed F. Aldawsari

Membranes 2022, 12(9), 862; https://doi.org/10.3390/membranes12090862 - 6 Sep 2022

Cited by 24 | Viewed by 3024

Abstract

The drying temperature is one of the crucial parameters that impacts the physical, chemical, and biological properties of edible films (EFs). This parameter determines the degree of crystallinity, which can further impact the film’s mechanical, barrier, and optical properties. The present work is [...] Read more.

The drying temperature is one of the crucial parameters that impacts the physical, chemical, and biological properties of edible films (EFs). This parameter determines the degree of crystallinity, which can further impact the film’s mechanical, barrier, and optical properties. The present work is designed to investigate the effect of different drying temperature conditions (25 °C and 45 °C) on ginger essential oil (GEO) loaded Gelatin-sodium alginate composite films over their physical, chemical, and antioxidant properties. Results indicated that drying of films at 25 °C had a positive effect on certain properties of the EFs, such as the moisture content (MC), water solubility (S), swelling degree (SD), water vapor permeability (WVP), and mechanical and optical properties. SEM analysis showed that films dried at 25 °C presented more uniform surface properties with fewer cracks and pores compared to films dried at 45 °C. TGA analysis demonstrated the higher thermal stability of the films when dried at 25 °C. Findings obtained from X-ray diffraction (XRD) and fourier-transform infrared spectroscopy (FTIR) showed film crystallinity and electrostatic interactions between GE, SA, and GEO. Results obtained from antioxidant assays revealed that films dried at 25 °C showed comparable antioxidant capacity to that of butylated hydroxytoluene (BHT). Furthermore, it was found that the addition of SA and GEO to the blank GE films improved their physical, chemical, and antioxidant properties. The present work suggests that GEO loaded GE-SA based films showed better physical, chemical, and antioxidant potential when dried at a lower temperature. These novel materials can be utilized as potential packaging materials in the food industry. Full article

► Show Figures

Graphical abstract

12 pages, 3001 KiB

Open AccessArticle

Sustainable Wax Coatings Made from Pine Needle Extraction Waste for Nanopaper Hydrophobization

by Sergejs Beluns, Oskars Platnieks, Jekaterina Sevcenko, Mara Jure, Gerda Gaidukova, Liga Grase and Sergejs Gaidukovs

Membranes 2022, 12(5), 537; https://doi.org/10.3390/membranes12050537 - 20 May 2022

Cited by 5 | Viewed by 3661

Abstract

We combine renewable and waste materials to produce hydrophobic membranes in the present work. Cellulose nanopaper prepared from paper waste was used as a structural component for the membrane. The pine wax was reclaimed from pine needle extraction waste and can be regarded [...] Read more.

We combine renewable and waste materials to produce hydrophobic membranes in the present work. Cellulose nanopaper prepared from paper waste was used as a structural component for the membrane. The pine wax was reclaimed from pine needle extraction waste and can be regarded as a byproduct. The dip-coating and spray-coating methods were comprehensively compared. In addition, the solubility of wax in different solvents is reported, and the concentration impact on coating quality is presented as the change in the contact angle value. The sensile drop method was used for wetting measurements. Spray-coating yielded the highest contact angle with an average of 114°, while dip-coating reached an average value of 107°. Scanning electron microscopy (SEM) was used for an in-depth comparison of surface morphology. It was observed that coating methods yield significantly different microstructures on the surface of cellulose fibers. The wax is characterized by nuclear magnetic resonance (NMR) spectroscopy and differential scanning calorimetry (DSC). Pine wax has a melting temperature of around 80 °C and excellent thermal stability in oxygen, with a degradation peak above 290 °C. Fourier transform infrared spectroscopy (FTIR) was used to identify characteristic groups of components and show the changes on coated nanopaper. Overall, the results of this work yield important insight into wax-coated cellulose nanopapers and a comparison of spray- and dip-coating methods. The prepared materials have a potential application as membranes and packaging materials. Full article

► Show Figures

Figure 1

17 pages, 3198 KiB

Open AccessReview

The Growth of Metal–Organic Frameworks in the Presence of Graphene Oxide: A Mini Review

by Nurul A. Mazlan, Fraz Saeed Butt, Allana Lewis, Yaohao Yang, Shuiqing Yang and Yi Huang

Membranes 2022, 12(5), 501; https://doi.org/10.3390/membranes12050501 - 6 May 2022

Cited by 19 | Viewed by 4007

Abstract

Integrated metal–organic frameworks (MOFs) with graphene oxide (GO) have aroused huge interest in recent years due to their unique properties and excellent performance compared to MOFs or GO alone. While a lot of attention has been focused on the synthesis methodologies and the [...] Read more.

Integrated metal–organic frameworks (MOFs) with graphene oxide (GO) have aroused huge interest in recent years due to their unique properties and excellent performance compared to MOFs or GO alone. While a lot of attention has been focused on the synthesis methodologies and the performance analysis of the composite materials in recent years, the fundamental formation/crystallization mechanism(s) is (are) still not fully understood. Ascribed to the distinctive structural and functional properties of GO, the nucleation and crystallization process of MOFs could be altered/promoted, forming MOF/GO composite materials with different nanostructures. Furthermore, the MOF’s parental structure could also influence how the GO and MOF bond together. Thus, this short review attempted to provide critical and indepth discussions of recent research results with a particular focus on the factors that influence the directional growth of parent MOFs in the presence of graphene oxide. Due to the unique structure and enhanced properties, the derived MOF/GO composites have a wide range of applications including gas separation, electrochemistry, and photocatalysis. We hope this review will be of interest to researchers working on MOF design, crystal structure control (e.g., orientation), and composite materials development. Full article

► Show Figures

Figure 1

Journal Menu

Journal Browser

Feature Papers in Membrane Engineering and Applications

Share This Topical Collection

Editors

Topical Collection Information

Keywords

Published Papers (16 papers)

2024

Jump to: 2023, 2022

2023

Jump to: 2024, 2022

2022

Jump to: 2024, 2023

Further Information

Guidelines

MDPI Initiatives

Follow MDPI