Search Results (163)

The growing demand for efficient and sustainable materials for air purification has stimulated interest in activated carbons derived from renewable biomass resources. In this study, activated carbons were prepared from Rice Husk, Wheat Straw, Sawdust, and Walnut shells and systematically investigated as sorbents for toxic gases and volatile organic compounds. The materials were characterized using nitrogen and water vapor sorption isotherms, scanning electron microscopy, thermogravimetric analysis, Fourier-transform infrared spectroscopy, energy-dispersive X-ray and XPS analysis to evaluate their textural properties, morphology, thermal stability, and surface chemistry. The results showed that the precursor type strongly influences the pore structure and functional group composition of the activated carbons. Wheat straw and Rice Husk-derived activated carbons exhibited the highest total pore volume and a well-developed porous structure, together with a high content of oxygen- and silicon-containing elements. Gas breakthrough experiments with different probes showed that Wheat Straw-derived activated carbon excels in non-polar VOC—cyclohexane removal due to its highly microporous structure. In contrast, Rice Husk-derived activated carbon displays strong affinity toward inorganic gases such as NH₃ and, after urea modification, achieves enhanced performance for SO₂. These results underscore the versatility and practical applicability of carbon materials obtained from plant residues. Full article

Soil hydraulic hysteresis—the divergence between drying and wetting trajectories of the water retention curve—encodes quantitative information on soil structural organization that traditional modelling approaches do not explicitly capture. This study introduces the State Resilience Index (SRI), a dimensionless descriptor defined as the normalized area enclosed between the drying and wetting branches of a hysteresis loop and evaluates its interpretive value across five contrasting datasets from the published literature. The datasets encompass compaction gradients, repeated wetting–drying cycles, depth-resolved soil profiles, and water vapor sorption isotherms from soils differing in clay content and mineralogy. SRI values ranged from 0.023 to 0.333, responding consistently to the dominant structural drivers of hysteresis in each system. High values were associated with heterogeneous, structurally complex pore networks characteristic of productive soils; declining values reflected progressive loss of structural memory under compaction, repeated cycling, or mineralogical rigidity. A provisional interpretive framework is proposed, linking SRI ranges to soil structural quality and agronomic potential. The index is dimensionless, model-free, and applicable across measurement domains and forcing regimes, positioning it as a broadly transferable tool for the comparative assessment of soil hydraulic path asymmetry. Full article

Earth-based materials are promising candidates for balancing thermal performance, hygrothermal regulation, and environmental sustainability. The objective of this study is to evaluate and compare the hygrothermal behavior of two earthen materials, structural cob and lightweight insulating earth, against conventional reference concrete, taking into account not only their insulating properties but also their ability to regulate coupled heat and moisture transfers. Experimental tests show a significantly higher hygroscopic buffering capacity for earth-based materials, with an MBV of 2.23 g/(m²∙%RH) for the structural material and 1.21 g/(m²∙%RH) for the insulation material, compared to less than 0.5 g/(m²∙%RH) for concrete. The sorption isotherms confirm distinct water storage behaviors, with an average sensitivity to relative humidity of 10.47% for the insulation material, compared to 3.8% for concrete and 2.25% for the structural material, in addition to an average reduction of 26% in the adsorption capacity between 23 °C and 45 °C for both earthen materials. Coupled heat–moisture simulations in COMSOL quantitatively demonstrate the hygrothermal superiority of bio-based materials over conventional concrete, as concrete promotes interstitial moisture accumulation due to its low vapor permeability. The parametric sensitivity analysis highlights the effect of hygrothermal properties, where diffusivity controls transport kinetics and sorption governs water storage, while thermal conductivity modulates the spatial redistribution of thermo-hygric fields. The next and final step made it possible to link the phenomena observed at the material scale to the actual energy performance of the building, confirming the potential of the double-wall cob + lightweight earth system to reduce heating and cooling requirements and maintain stable indoor comfort, where the annual heating demand is reduced by approximately 24% compared to the conventional prototype. Full article

This study investigates the development of mixed matrix membranes based on polyethersulfone incorporated with attapulgite for gas separation applications, addressing the existing gap regarding the use of this mineral in dense membranes obtained exclusively by solvent evaporation and its combined effects on microstructure and transport. The membranes were prepared by phase inversion via solvent evaporation, using solvent/polymer ratios of 75/25 and 80/20 and a thickness of 0.25 mm. The solutions were evaluated in terms of viscosity, and the membranes were characterized by structural techniques such as X-ray diffraction (XRD), atomic force microscope (AFM), contact angle, mechanical properties (tensile testing), and water vapor permeation. The results showed that attapulgite incorporation promoted a reduction in surface roughness (up to ~40%) and a decrease in contact angle (from ~89° to ~68°), indicating increased hydrophilicity. In addition, water vapor permeability was influenced in a non-linear manner, with optimized performance observed at 3 wt% filler loading. Solution viscosities remained within ranges suitable for processing. Structural analyses indicated compatibility between the phases, while morphology changes dependent on filler content were decisive for transport behavior. It is concluded that attapulgite is a promising additive for fine-tuning membrane properties, enabling optimization of the sorption–diffusion balance and improvement of membrane performance in separation applications. Full article

Fungal decay fundamentally alters moisture transport in wood through complex bio-physical coupling mechanisms that remain poorly understood. Brown-rot fungi such as Coniophora puteana (Schumach.: Fr.) P. Karst. degrade wood through chelator-mediated Fenton (CMF) chemistry, producing hydroxyl radicals that depolymerise cellulose and hemicellulose before significant mass loss. This diffusion-dependent process requires elevated moisture content and leads to structural degradation. However, existing models fail to capture the interaction between boundary-driven fungal colonization, decay-induced property changes, and multi-phase multi-Fickian moisture redistribution, particularly the separate evolution of bound- and free-water phases during decay. Here, we present a transport-response bio-hygrothermal finite element model that couples boundary-driven Monod-type fungal colonization kinetics with multi-phase moisture transport (free water, bound water, vapor) in decaying wood. Although fungal biomass evolution is simulated via a reaction–diffusion equation, decay progression is not derived from biomass–substrate interaction but prescribed independently as an experimentally informed input. The model incorporates decay-modified sorption isotherms, permeability evolution, and boundary-driven biomass influx, along with associated moisture transport, into the governing equations. The model is validated against low-field nuclear magnetic resonance (LF-NMR) measurements of C. puteana decay in Scots pine over 35 days. The model successfully reproduces the experimentally observed moisture evolution: a peak free-water content of 50%–70% during weeks 1–2, followed by a progressive decline, while bound water remains remarkably constant despite advancing decay. Monte Carlo uncertainty quantification demonstrates hierarchical parameter control: bound water is governed solely by thermodynamic factors, while free water responds to interacting biological and physical processes. Time-resolved correlation analysis shows a fundamental transition from colonization-dominated (weeks 1–2) to transport-dominated (weeks 3–5) moisture control, quantitatively explaining the experimentally observed shift from accumulation to depletion. This transport-response framework for analyzing moisture behavior under externally defined decay progression establishes quantitative parameter hierarchies that may inform the development of future substrate-coupled bio-hygrothermal models. Full article

Water vapor sorption in porous activated carbons (PACs) is governed by a complex interplay of pore architecture and surface functionality and often exhibits pronounced adsorption–desorption hysteresis. In this work, chestnut-shell-derived carbons were synthesized via a two-step thermal route—pyrolysis at 550 °C for 120 min followed by KOH activation at either 600 °C or 800 °C for 240 min—and evaluated using a dynamic vapor sorption analyzer to quantify water uptake, hysteresis, and temperature-dependent energetics. Both materials exhibit sigmoidal Type V isotherms, characteristic of cooperative water clustering on hydrophobic carbon surfaces with localized polar sites. At 25 °C, The PAC sample prepared at 800 °C shows a sharper uptake transition and higher total capacity (~0.45 g/g at 90% RH), compared to the broader, more gradual isotherm of the 600 °C sample (~0.17 g/g). Temperature-dependent isotherms collected between 25 °C and 45 °C were fit using the Dubinin–Serpinsky (DS-4) model, yielding good agreement (R² ≈ 0.997) and enabling mechanistic interpretation of primary site adsorption and cooperative cluster growth. Clausius–Clapeyron analysis of ln P versus 1/T at fixed loadings yielded isosteric heats of adsorption (ΔH) decreasing from approximately 45.4 kJ mol⁻¹ at low uptake (0.02 g g⁻¹) to ~43.8 kJ mol⁻¹ at intermediate loading, followed by a slight increase to ~44.2 kJ mol⁻¹ at higher coverage (0.35 g g⁻¹). This trend reflects the transition from strong adsorption at high-energy surface sites to cooperative water clustering and confinement effects within the pore network. These findings highlight the role of activation temperature in modulating sorption mechanisms and energetics, offering practical guidance for tuning biomass-derived carbons for atmospheric water harvesting applications. Full article

This study explores novel silica gel/sulfonated polymer composite coatings for enhanced thermal management in electric vehicles via sorption technology. Leveraging the cost-effectiveness of silica gel as a filler and a readily available, water vapor-permeable sulfonated polymer as the matrix, we developed and characterized these materials. Mechanical assessments revealed varied performance: coatings with lower silica gel content (80 and 85 wt%) demonstrated suitable scratch resistance (damage width ~1100 µm at 1300 g load) and superior impact resistance (damage diameter ~2.4 mm). Pull-off adhesion strengths for these batches were 1.26 MPa and 1.36 MPa, respectively, though higher filler loading (90 and 95 wt%) led to a ~30% reduction and a shift to cohesive failure for high-filler-content batches. Thermogravimetric analysis confirmed thermal stability up to 280 °C. Adsorption studies revealed that the composite coating with 95 wt% of silica gel achieved the highest water uptake (just under 30 wt%), with all batches exhibiting capacities comparable to commercial adsorbents. This comprehensive characterization confirms that these composites offer a compelling balance of mechanical robustness, reliable adhesion, and high adsorption efficiency, positioning them as promising, cost-effective solutions for EV thermal management. Full article

A new method of in situ hydrothermal reduction of graphene oxide (GO) to reduced graphene oxide (rGO) in polymer bulk was developed, which involves heating GO/polyacrylonitrile (PAN) composite membranes (0.5; 1.0; 2.0% w/w of GO/PAN) in the presence of water vapor at a temperature of 120 °C and a pressure of 0.2 MPa. As a result of this process, membranes containing rGO were obtained, as confirmed by FTIR, Raman, WAXS and TGA studies. The composite membranes obtained after hydrothermal reduction of GO to rGO (B60, C60, D60) were substantially different from the initial membranes containing unreduced GO (B0, C0, D0). The hydrothermal reduction process clearly influenced the physicochemical properties (reduction of apparent density, water sorption, and increase in the contact angle) and transport properties of the B60, C60, and D60 membranes (decrease in water flux by ~104 [dm³/m² × h] and even ~348 [dm³/m² × h] compared to the initial membranes). Full article

Urban leaf litter represents an underutilized biomass resource with potential applications in sustainable building materials. This study investigates the suitability of dried, comminuted leaves collected from municipal green areas as a loose-fill thermal insulation material. The material was characterized in terms of thermal conductivity, settlement behavior, fire reaction, resistance to mold growth, water vapor diffusion, hygroscopic sorption, and short-term water absorption. Tests were conducted following relevant DIN and ISO standards, with both untreated and flame-retardant-treated samples examined. Results indicate that the thermal conductivity of leaf-based insulation (λ = 0.041–0.046 W/m·K) is comparable to other bio-based loose-fill materials such as cellulose and wood fiber. Optimal performance was achieved for particles sized 2–16 mm, showing settlement below 1%. All variants, including untreated material, fulfilled the fire resistance requirements of class E, while selected treatments further improved fire resistance. The material exhibited moderate vapor permeability (μ ≈ 4–5), low water absorption, and moisture buffering behavior similar to that of other bio-based insulation materials. Resistance to mold growth was satisfactory under standardized conditions. Overall, the results demonstrate that leaf litter can serve as an effective and environmentally favorable loose-fill insulation material, offering an innovative recycling pathway for urban green waste. Full article

A multi-stage TG-DSC approach consisting of five heating/holding and five cooling/holding stages within one experiment in the temperature range 20–320 °C was applied to investigate the dehydration/hydration processes in K⁺, Na⁺, Ca²⁺, and Mg²⁺ clinoptilolite forms. The influence of extra-framework cations on the parameters characterizing these processes (such as mass changes, dehydration and hydration heats calculated per gram zeolite, amounts of water molecules leaving and entering the structure, and enthalpy values calculated per mol water) was established. The values of molar enthalpy of dehydration for different cationic clinoptilolite forms increase in different ways with temperature increasing (within the framework of 50–120 kJ mol⁻¹). The data on the molar enthalpy are in good agreement with the distributions of the two types of water molecules—weakly bound to cations and water molecules coordinating cations in the applied crystal chemical models of the cationic exchange samples. The data obtained for water molecules and their molar enthalpies of dehydration for the various cationic forms are useful in studying the sorption of water vapor and other sorbates, in choosing a desiccant and an object to dry at room conditions, etc. The first data on the hydration energy of sequentially added water molecules in a dynamic cooling mode in the temperature range 320–20 °C were obtained. Full article

This paper presents a new study and analysis of the thermo-hygroscopic behavior of Arthrospira platensis using dynamic vapor sorption (DVS) system. Thermo-hygroscopic characterization is essential for optimizing the drying process and enhancing storage conditions. Therefore, the objective of this work was to investigate the thermo-hygroscopic properties of Arthrospira (Spirulina) platensis using a dynamic vapor sorption (DVS) system. This thermo-hygroscopic analysis focused on three fundamental parameters, namely: the desorption isotherms, the net isosteric heat of water desorption, and the moisture diffusivity. Desorption isotherms were measured at five different temperatures (25 °C, 40 °C, 50 °C, 60 °C and 80 °C) over a relative humidity range of 10–80%. The desorption isotherm data were fitted to five semi-empirical models: GAB, Oswin, Smith, Henderson, and Peleg. The results indicated that the GAB model provided the best fit for the experimental data. The net isosteric heat of desorption was determined using the Clausius–Clapeyron relation. It decreased from 21.3 to 4.29 KJ/mol as the equilibrium moisture content increased from 0.02 to 0.1 Kg/Kg (dry basis). Additionally, the moisture diffusivity of Arthrospira platensis was estimated based on Fick’s second law of diffusion and the desorption kinetics obtained from the DVS equipment. This parameter varied between 1.04 10⁻⁸ m²/s and 1.46 10⁻⁷ m²/s for average moisture contents ranging from 0.003 Kg/Kg to 0.191 Kg/Kg (dry basis). Furthermore, the activation energy for desorption was estimated to be approximately 33.7 KJ/mol. Full article

The paper presents the experimental study of the zeolite heat storage unit discharging process in a laboratory scale. The Authors focused on the discharging process, which utilizes adsorption of water, in the form of steam, on zeolite, because the adsorption process is considered as more challenging in terms of reaction kinetics and heat transfer. The Authors designed and built a laboratory stand with a sorption heat storage unit filled with 13X zeolite and with a separated heat transfer fluid system, where air was used for discharging. Dynamic parameters including the temperature of inlet and outlet air and the temperature distribution inside the zeolite bed during the discharging process were investigated. The gathered measurement data were used to determine the heat fluxes and to compute dynamic heat balance of the thermal storage unit including internal and external heat losses. It was demonstrated that the applied design and scale of the thermal storage unit allows to reach the thermal power over 300 W and heat the discharging air from 40 °C to over 110 °C. The innovative aspect of the study is the improvement of operational stability of the sorption heat storage unit through the implementation of a heat exchanger design that separates the heat transfer fluid from the zeolite bed, as well as a control system with a neural network layer for predicting the mass flow rate of steam. Full article

Multilayer packaging materials are extensively used in food packaging, particularly for powdered products. In alignment with sustainable development goals, packaging design should aim to minimize material usage while maintaining the protective properties necessary to preserve food quality and safety, thereby reducing environmental impact. A key strategy is to simplify multilayer structures to enhance recyclability. This study aims to evaluate the potential of sustainable alternative packaging materials with reduced metal and plastic content and improved recyclability for pudding powder packaging, as substitutes for conventional films. Four packaging structures were tested: a conventional three-layer laminate (polyethylene terephthalate (PET)/aluminum foil (Al-foil)/low-density polyethylene (LDPE)), two two-layer structures (AlO_x-coated PET/LDPE and Al-coated PET/LDPE), and a monolayer metallized biaxially oriented polypropylene (MetBOPP). Samples were stored under accelerated conditions (38 °C and 90% relative humidity) for 180 days, and changes in moisture content, water activity, caking degree, glass transition temperature, color, and sensory attributes were monitored. The experimental data were examined for their agreement with various sorption models by creating adsorption isotherms. The acceptable storage period was estimated using the constants calculated from these models. Statistically significant differences (p < 0.05) were observed among the packaging types, primarily associated with their water vapor permeability, affecting moisture content, water activity, caking degree, and color stability. In terms of moisture content, water activity, and caking degree, the conventional PET/Al-foil/LDPE (Polyethylene terephthalate/Aluminum foil/Low density polyethylene) structure demonstrated the best performance, followed by PET.AlO_x/LDPE (AlO_x-coated Polyethylene terephthalate/Low density polyethylene), MPET/LDPE (Metallized polyethylene terephthalate/Low density polyethylene), and MBOPP (Metallized biaxially oriented polypropylene), respectively. The sensory analysis scores followed the same ranking; however, all samples maintained scores above the threshold value of 3 throughout the storage period, indicating that they remained acceptable. Caking degree increased moderately (from 0.61% to 0.89%) and was negatively correlated with appearance scores (R² = −0.89, p < 0.01). Despite slight darkening (Browning Index increased from 18.16 to 20.37), sensory scores for appearance, odor, and taste remained above the acceptable threshold (score > 3.0). Based on the WVTR values of the packaging materials and the application of the GAB model, the estimated shelf lives were 800.32 days for PET/Al-foil/LDPE, 577.92 days for PET.AlO_x/LDPE, 407.58 days for MPET/LDPE, and 229.26 days for MBOPP. In conclusion, the longest shelf life was achieved with PET/Al-foil/LDPE, and it was observed that as the WVTR of the packaging materials increased, the shelf life of the cocoa-based pudding powder decreased; PET.AlO_x/LDPE and MPET/LDPE could be considered for medium-term storage (up to about 1–1.5 years), while MBOPP appeared suitable only for shorter durations (6–8 months). Full article

Biodegradable composites obtained by reinforcing thermoplastic starch (TPS) with lignocellulosic fibers show great potential, but their strong sensitivity to water still limits practical applications. Among possible reinforcements, Helianthus tuberosus (topinambur) represents an underutilized agricultural residue that has been scarcely explored in this context. In this work, we demonstrate for the first time that topinambur fiber can improve the water vapor barrier properties of cassava starch films, while also providing a detailed analysis of sorption isotherms and the humidity-dependent relationship between surface roughness and contact angle, aspects rarely addressed in previous studies. SEM revealed uniform fiber dispersion and integration. Water sorption kinetics showed that fiber addition reduces both hydration and sorption time constant, indicating lower water affinity and greater water mobility. Water sorption isotherms confirmed that fiber incorporation significantly alters overall hydration and water–matrix interactions, revealing reduced effective water solubility in films. Water vapor permeability also decreased with fiber addition, mainly due to decreased water solubility, rather than changes in water diffusivity. While fiber addition enhanced surface-water repellency across all humidity levels, roughness exhibited a humidity-dependent response FTIR analysis confirmed fiber–matrix compatibility and suggested new hydrogen bonding. Overall, these findings identify topinambur fiber as a novel reinforcement for designing biodegradable films with improved humidity resistance for agroecological applications. Full article

Background: Dark-base hair fibers with Curl Pattern (CP) types 2 and 3 from Asian and European populations, respectively, are very similar, although each presents different behaviors regarding water diffusion and cosmetic treatments, including in relation to dyeing. This study aims to identify the key drivers of water diffusion in hair, particularly the role of lipids in the diffusion processes. Methods: Virgin, externally delipidized, and internally delipidized CP2 and CP3 hair strands were subjected to Dynamic Vapor Sorption (DVS) and ATR-FTIR investigations. In addition, external and internal lipid extracts were quantified and analyzed via thin-layer chromatography–flame ionization detection (TLC/FID). Results: The results obtained indicate that CP2 hairs present lower water regain at all humidity steps and a different diffusion behavior depending on the humidity. Lower diffusion was obtained at low humidity and higher diffusion at high humidity. TLC/FID analyses indicate that CP2 fibers present a significantly higher amount of external lipids (1.4% vs. 0.4%) and internal lipids (3.2% vs. 2.6%) as compared with the CP3 fibers. Conclusions: The higher amount of internal lipids is mainly due to the greater amount of polar lipids (ceramides). Lipid extraction tends to modify the water content, leading to a more hydrated and less permeable lipid-depleted fiber. The similar water properties of the two types of lipid fiber support the fundamental role of lipids, even when present in small quantities, in the differentiation of hair types. This study highlights a potential link between the lipid composition of CP3 and CP2 hair fibers and their differences in behaviors regarding water diffusion, which could also explain varying responses to cosmetic treatments. Full article