Search Results (190)

Shandong Province is rich in geothermal resources, mainly stored in sandstone reservoirs. The setting of reasonable well spacing in the early stage of large-scale recharge has not attracted enough attention. The problem of small well spacing in geothermal engineering is particularly prominent in the sandstone thermal reservoir production area represented by Dezhou. Based on the measured data of temperature, flow, and water level, this paper constructs a typical engineering numerical model by using TOUGH2 software. It is found that when the distance between production and recharge wells is 180 m, the amount of production and recharge is 60 m³/h, and the temperature of reinjection is 30 °C, the temperature of the production well will decrease rapidly after 10 years of production and recharge. In order to solve the problem of thermal breakthrough, three optimization schemes are assumed: reducing the reinjection temperature to reduce the amount of re-injection when the amount of heat is the same, reducing the amount of production and injection when the temperature of production and injection is constant, and stopping production after the temperature of the production well decreases. However, the results show that the three schemes cannot solve the problem of thermal breakthrough or meet production demand. Therefore, it is necessary to set reasonable well spacing. Therefore, based on the strata near the Hydrological Homeland in Decheng District, the reasonable spacing of production and recharge wells is achieved by numerical simulation. Under a volumetric flux scenario ranging from 60 to 80 m³/h, the well spacing should exceed 400 m. For a volumetric flux between 80 and 140 m³/h, it is recommended that the well spacing be greater than 600 m. Full article

Under the trend of lightweight and high-efficiency development in industrial equipment, precise regulation of lubrication in gear reducers is a key breakthrough for enhancing transmission system efficiency and reliability. This study establishes a three-dimensional numerical model for high-speed gear jet lubrication using computational fluid dynamics (CFD) and dynamic mesh technology. By implementing the volume of fluid (VOF) multiphase flow model and the standard k-ω turbulence model, the study simulates the dynamic distribution of lubricant in gear meshing zones and analyzes critical parameters such as the oil volume fraction, eddy viscosity, and turbulent kinetic energy. The results show that reducing the oil injection distance significantly enhances lubricant coverage and continuity: as the injection distance increases from 4.8 mm to 24 mm, the lubricant shifts from discrete droplets to a dense wedge-shaped film, mitigating lubrication failure risks from secondary atomization and energy loss. The optimized injection distance also improves the spatial stability of eddy viscosity and suppresses excessive dissipation of turbulent kinetic energy, enhancing both the shear-load capacity and thermal management. Dynamic data from monitoring point P show that reducing the injection distance stabilizes lubricant velocity and promotes more consistent oil film formation and heat transfer. Through multiphysics simulations and parametric analysis, this study elucidates the interaction between geometric parameters and hydrodynamic behaviors in jet lubrication systems. The findings provide quantitative evaluation methods for structural optimization and energy control in gear lubrication systems, offering theoretical insights for thermal management and reliability enhancement in high-speed transmission. These results contribute to the lightweight design and sustainable development of industrial equipment. Full article

A major breakthrough in environmentally friendly building materials is the development of sustainable unfired clay bricks including alumina waste produced during liquid nitrogen generation. Though used extensively, conventional fired clay bricks require energy-intensive manufacturing techniques that produce significant amounts of CO₂ and aggravate environmental damage. By removing the need for high-temperature firing and allowing for the valorization of industrial byproducts including alumina waste and lateritic soil, unfired clay bricks offer a reasonable low-carbon alternative. High silica and alumina contents define the alumina waste, which shows pozzolanic reactivity, thus improving the physicomechanical performance of the bricks. With alumina waste substituting 0–8.57% of the cement content, seven different formulations showed improvements in compressive strength, reduced water absorption, and optimal thermal conductivity. Especially, the mechanical performance was much enhanced with alumina waste inclusion up to 30%, without sacrificing thermal insulation capacity or moisture resistance. Further supporting the environmental and financial sustainability of the suggested brick compositions is the economic viability of using industrial waste and regionally derived soils. A comparative analysis of the conventional fired bricks shows that the unfired substitutes have a much lower environmental impact and show better mechanical properties, including greater compressive strength and modulus of rupture. These results support the more general goals of circular economy systems and low-carbon urban development by highlighting the feasibility of including alumina waste and lateritic soil into sustainable building materials. Using such waste-derived inputs in building fits world initiatives to lower resource consumption, lower greenhouse gas emissions, and build strong infrastructure systems. Full article

Under the accelerating global energy restructuring and the deepening carbon neutrality strategy, hydrogen energy has emerged with increasing strategic value as a zero-carbon secondary energy carrier. Water electrolysis technology based on renewable energy is regarded as an ideal pathway for large-scale green hydrogen production. However, polymer electrolyte membrane (PEM) conventional water electrolysis faces dual constraints in economic feasibility and scalability due to its high electrical energy consumption and reliance on noble metal catalysts. The mixed ionic-electronic conducting oxygen transport membrane (MIEC–OTM) reactor technology offers an innovative solution to this energy efficiency-cost paradox due to its thermo-electrochemical synergistic energy conversion mechanism and process integration. This not only overcomes the thermodynamic equilibrium limitations in traditional electrolysis but also reduces electrical energy demand by effectively coupling with medium- to high-temperature heat sources such as industrial waste heat and solar thermal energy. Therefore, this review, grounded in the physicochemical mechanisms of oxygen transport membrane reactors, systematically examines the influence of key factors, including membrane material design, catalytic interface optimization, and parameter synergy, on hydrogen production efficiency. Furthermore, it proposes a roadmap and breakthrough directions for industrial applications, focusing on enhancing intrinsic material stability, designing multi-field coupled reactors, and optimizing system energy efficiency. Full article

To achieve a significant breakthrough in the exploration of uranium resources in the Guangzitian area of northern Guangxi, China, an innovative combination of exploration methods was implemented at the peripheral regions of the Guangzitian uranium deposit under the guidance of the following principle: “exploring the edges and identifying the bottom, delving deep and un-covering blind spots”. This study introduces geo-electrochemical integrated technology for prospecting research at the peripheral areas of the Guangzitian deposit. By validating the technology’s effectiveness on known geological sections, distinct geo-electrochemical extraction anomalies were identified above recognized ore bodies. Simultaneously, soil ionic conductivity and thermally released mercury anomalies were observed, partially indicating the presence of concealed uranium deposits and fault structures. These findings demonstrate that geo-electrochemical integrated technology is effective in detecting buried uranium mineralization in this region. Subsequently, a geological-geoelectrical prospecting model was established through a systematic analysis of anomaly characteristics and metallogenic regularity, and it was subsequently applied to unexplored areas. As a result, one key anomaly verification zone, one Class A comprehensive anomaly zone, two Class B comprehensive anomaly zones, and one Class C comprehensive anomaly zone were identified within the unexplored research area. Drilling engineering validation was conducted in the No. Ι key anomaly verification zone, resulting in the discovery of an industrial-grade uranium ore body. This achievement not only provides critical technical support but also develops a robust theoretical foundation for future mineral exploration endeavors. Full article

Gypsum and salt rocks have been proven to act as seals for abundant oil and gas reserves on a global scale, with significant potential for hydrocarbon preservation and evolution. Notably, the sedimentary dynamics of non-evaporitic gypsum in terrestrial half-graben basins remain underexplored, particularly regarding its genetic link to hydrocarbon accumulation in interbedded mudstones. This study is based on the Zhanhua Sag, in which thick-layered gypsum rocks with dark mudstone are deposited. The gypsum crystals show the intermittent deposition characteristics. The cumulative thickness of the gypsum-containing section reaches a maximum of over 110 m. The spatial distribution of gypsum thickness correlates strongly with the location of deep-seated faults. The strontium and sulfur isotopes of gypsum indicate deep hydrothermal fluids as mineral sources, and negative oxygen isotope excursions also suggest that gypsum layers precipitated in situ from hot brine. Total organic carbon and Rock-Eval data indicate that the deep-lake gypsum rock system has excellent hydrocarbon potential, especially in the mudstone interlayers. This study developed a depositional model of deep-lake gypsum rocks with thermal brine genesis in half-graben basins. The gypsum-bearing system is rich in mudstone interlayers. These gypsum–mudstone interbeds represent promising targets for shale oil exploration after the initial breakthrough during the extraction process. These insights provide a theoretical framework for understanding gypsum-related petroleum systems in half-graben basins across the globe, offering guidance for hydrocarbon exploration in analogous sedimentary environments. Full article

Titanium dioxide (TiO₂) is a wide-bandgap semiconductor material with broad application potential, known for its excellent photocatalytic performance, high chemical stability, low cost, and non-toxicity. These properties make it highly attractive for applications in photovoltaic energy, environmental remediation, and optoelectronic devices. For instance, TiO₂ is widely used as a photocatalyst for hydrogen production via water splitting and for degrading organic pollutants, thanks to its efficient photo-generated electron–hole separation. Additionally, TiO₂ exhibits remarkable performance in dye-sensitized solar cells and photodetectors, providing critical support for advancements in green energy and photoelectric conversion technologies. Boron-doped diamond (BDD) is renowned for its exceptional electrical conductivity, high hardness, wide electrochemical window, and outstanding chemical inertness. These unique characteristics enable its extensive use in fields such as electrochemical analysis, electrocatalysis, sensors, and biomedicine. For example, BDD electrodes exhibit high sensitivity and stability in detecting trace chemicals and pollutants, while also demonstrating excellent performance in electrocatalytic water splitting and industrial wastewater treatment. Its chemical stability and biocompatibility make it an ideal material for biosensors and implantable devices. Research indicates that the combination of TiO₂ nanostructures and BDD into heterostructures can exhibit unexpected optical and electrical performance and transport behavior, opening up new possibilities for photoluminescence and rectifier diode devices. However, applications based on this heterostructure still face challenges, particularly in terms of photodetector, photoelectric emitter, optical modulator, and optical fiber devices under high-temperature conditions. This article explores the potential and prospects of their combined heterostructures in the field of optoelectronic devices such as photodetector, light emitting diode (LED), memory, field effect transistor (FET) and sensing. TiO₂/BDD heterojunction can enhance photoresponsivity and extend the spectral detection range which enables stability in high-temperature and harsh environments due to BDD’s thermal conductivity. This article proposes future research directions and prospects to facilitate the development of TiO₂ nanostructured materials and BDD-based heterostructures, providing a foundation for enhancing photoresponsivity and extending the spectral detection range enables stability in high-temperature and high-frequency optoelectronic devices field. Further research and exploration of optoelectronic devices based on TiO₂-BDD heterostructures hold significant importance, offering new breakthroughs and innovations for the future development of optoelectronic technology. Full article

Phytosterols (PS) have specific oxidation rules in different lipid media. After oxidation, PS will form oxidation products, which has potential physiological toxicity to the human body. Camellia seed oil (CSO) is a unique emerging edible oil in China. This oil has a fatty acid composition similar to olive oil, in which oleic acid is dominant. In order to solve the thermal oxidation of PS in CSO at high temperature (180 °C), we studied its antioxidant strategy by evaluating different antioxidants. Four antioxidants—BHA, TBHQ, epigallocatechin gallate (EGCG), and α-tocopherol (VE)—along with one synergist, citric acid (CA), were selected and used in this study. The antioxidant effects of different combinations (single antioxidant, single antioxidant + CA, mixed antioxidant, mixed antioxidant + CA) were compared. After 180 min of heating, the PS and phytosterols oxidation products (7α-hydroxy-, 7β-hydroxy-, 5α,6α-epoxy-, 5β,6β-epoxy-, 7-keto-, and trihydroxy-PS) were estimated by GC-MS. Through comparative analysis, the results showed that the combination of mixed antioxidants and CA had the best antioxidant effect, and the inhibition rate of VE + TBHQ +CA was as high as 42%, which had a breakthrough significance for stabilizing the thermal oxidation of PS in camellia seed oil. At the same time, it also provides a valuable reference for ensuring the edible safety of camellia seed oil in Chinese food heating habits. Full article

Recent advancements in thermally activated delayed fluorescence (TADF) materials and mechanochromic materials have significantly enhanced the efficiency and versatility of light-emitting electrochemical cells (LECs) and organic light-emitting diodes (OLEDs). TADF materials have enabled efficiency improvements, achieving an internal quantum efficiency (IQE) of nearly 100% by utilizing both singlet and triplet excitons. Meanwhile, mechanochromic materials exhibit reversible optical changes upon mechanical stimuli, making them promising for stress sensing, encryption, and flexible electronics. The synergistic integration of TADF and mechanochromic materials in OLEDs and LECs has led to enhanced efficiency, stability, and multifunctionality in next-generation lighting and display technologies. This narrative review explores recent breakthroughs in devices that incorporate both TADF and mechanochromic materials as emitters. Particular attention is given to the molecular design that enable both TADF and mechanochromic properties, as well as optimal device structures and performance parameters. Moreover, this review discusses the only LEC fabricated so far using a TADF-mechanochromic emitter, highlighting its performance and potential. Finally, the report concludes with an outlook on the future commercial applications of these materials, particularly in wearable electronics and smart display technologies. Full article

Abiotic stress constrains plant growth and productivity worldwide. To survive adverse environmental conditions, plants deploy sophisticated adaptive strategies involving transcriptional reprogramming and metabolic remodeling. Over the past decade, advancements in high-throughput sequencing and mass spectrometry have propelled transcriptomics and metabolomics as pivotal post-genomic disciplines, offering unprecedented opportunities to dissect molecular mechanisms underlying stress responses. This review synthesizes current progress in applying these omics technologies to investigate plant adaptations to key abiotic stresses (thermal, saline, water deficit/excess, and heavy metal stresses). We systematically evaluate the technical strengths and limitations of transcriptomic and metabolomic platforms, highlight recent breakthroughs in stress-responsive gene identification and metabolic pathway elucidation, and discuss emerging challenges in integrative data analysis. By bridging genotype–phenotype relationships through multi-omics approaches, this study aims to deepen our mechanistic understanding of plant stress resilience and inform the design of stress-resilient crops for sustainable agriculture. Full article

Carbonate geothermal reservoirs, characterized by widespread distribution, a high discharge capacity, and favorable reinjection conditions, have become a key target for geothermal resource development. However, the karst geothermal reservoir system in the Juancheng geothermal field exhibits significant heterogeneity, leading to substantial disparities in productivity among multiple geothermal wells and severely restricting efficient regional exploitation. This study systematically investigates the hydraulic characteristics and development potential of the karst geothermal reservoir in the Juancheng geothermal field using sodium fluorescein tracing experiment technology. The results reveal that the reservoir system contains multiple flow channels with distinct permeability differences. The dominant flow pathways, controlled by fault structures, exhibit an apparent velocity of up to 10.98 m/h, significantly higher than other regions in the study area. In contrast, low-permeability zones, influenced by the burial depth of the Ordovician strata, show poor connectivity due to limited karst development, with the lowest apparent velocity of only 1.03 m/h. By integrating pumping test data and tracer response characteristics, the dominant flow direction (northeast) demonstrates a stronger recharge capacity and water abundance, offering a higher development value. Conversely, the southeast low-permeability zone has weaker water production and constrained recharge conditions, resulting in a relatively limited development potential. Additionally, it is recommended that the direction of future geothermal well placement in the Juancheng geothermal field should avoid being parallel to the fault strike to prolong the thermal breakthrough arrival time. In regions with deeper Ordovician strata burial, denser well network deployment is suggested to enhance the reservoir utilization efficiency. Full article

The rapid advancement of sustainable materials has driven the need for high-performance polymer nanocomposites with superior mechanical, thermal, and structural properties. In this study, a novel RPET/PA-11/Joncryl^® nanocomposite reinforced with halloysite nanotubes (HNTs) is developed for the first time, marking a significant breakthrough in polymer engineering. Six different proportions of HNT (0, 1, 2, 3, 4, and 5 phr) are introduced to the blend of rPET/PA-11/Joncryl^® through a twin-screw extruder and injection moulding machine. The incorporation of HNTs into the RPET/PA-11 matrix, coupled with Joncryl^® as a compatibilizer, results in a synergistic enhancement of material properties through improved interfacial adhesion, load transfer efficiency, and nanoscale reinforcement. Comprehensive characterization reveals that the optimal formulation with 2 phr HNT (NCS-H2) achieves remarkable improvements in tensile strength (56.14 MPa), flexural strength (68.34 MPa), and Young’s modulus (895 MPa), far exceeding conventional polymer blends. Impact resistance reaches 243.46 J/m, demonstrating exceptional energy absorption and fracture toughness. Thermal analysis confirms enhanced stability, with an onset degradation temperature of 370 °C, attributing the improvement to effective matrix–filler interactions and restricted chain mobility. Morphological analysis through FESEM validates uniform HNT dispersion at optimal loading, eliminating agglomeration-induced stress concentrators and reinforcing the polymer network. The pioneering integration of HNT into RPET/PA-11/Joncryl^® nanocomposites not only bridges a critical gap in sustainable polymers but also establishes a new benchmark for polymer nanocomposites. This work presents an eco-friendly solution for engineering applications, offering mechanical robustness, thermal stability, and recyclability. The results form the basis for next-generation high-performance materials for industrial use in automotive, aerospace, and high-strength structural applications. Full article

As the energy sector transitions toward decarbonisation, low-to-intermediate temperature geothermal resources in sedimentary basins—particularly repurposed oil and gas fields—have emerged as promising candidates for sustainable heat and power generation. Despite their widespread availability, the development of these systems is hindered by gaps in methodology, oversimplified modelling assumptions, and a lack of integrated analyses accounting for long-term reservoir and wellbore dynamics. This study presents a detailed, simulation-based framework to evaluate geothermal energy extraction from depleted petroleum reservoirs, with a focus on low-enthalpy resources (<150 °C). By examining coupling reservoir behaviour, wellbore heat loss, reinjection cooling, and surface energy conversion, the framework provides dynamic insights into system sustainability and net energy output. Through a series of parametric analyses—including production rate, doublet spacing, reservoir temperature, and field configuration—key performance indicators such as gross power, pumping requirements, and thermal breakthrough are quantified. The findings reveal that: (1) net energy output is maximised at optimal flow rate (~70 kg/s for a 90 °C reservoir), beyond which increased pumping offsets thermal gains; (2) doublet spacing has a non-linear impact on reinjection cooling, with larger distances reducing thermal interference and pumping energy; (3) reservoirs with higher temperatures (<120°C) offer significantly better thermodynamic and hydraulic performance, enabling pump-free or low-duty operations at higher flow rates; and (4) wellbore thermal losses and reinjection effects are critical in determining long-term viability, especially in low-permeability or shallow fields. This work demonstrates the importance of a coupled, site-specific modelling in assessing the geothermal viability of petroleum fields and provides a foundation for future techno-economic and sustainability assessments. The results inform optimal design strategies and highlight scenarios where the geothermal development of oil and gas fields can be both technically and energetically viable. Full article

The dominant low-light object detectors face the following spectral trilemma: (1) the loss of high-frequency structural details during denoising, (2) the amplification of low-frequency illumination distortion, and (3) cross-band interference in multi-scale features. To resolve these intertwined challenges, we present UMFNet—a frequency-guided detection framework that unifies adaptive frequency distillation with inter-band attention coordination. Our technical breakthroughs manifest through three key innovations: (1) a frequency-adaptive fusion (FAF) module employing learnable wavelet kernels (16–64 decomposition basis) with dynamic SNR-gated thresholding, achieving an 89.7% photon utilization rate in ≤1 lux conditions—2.4× higher than fixed-basis approaches; (2) a spatial-channel coordinated attention (SCCA) mechanism with dual-domain nonlinear gating that reduces high-frequency hallucination by 37% through parametric phase alignment (verified via gradient direction alignment coefficient ${\rho }_G$ = 0.93); (3) a spectral perception loss combining the frequency-weighted structural similarity index measure (SSIM) with gradient-aware focal modulation, enforcing physics-constrained feature recovery. Extensive validation demonstrates UMFNet’s leadership: 73.1% mAP@50 on EXDark (+6.4% over YOLOv8 baseline), 58.7% on DarkFace (+3.1% over GLARE), and 40.2% on thermal FLIR ADAS (+9.7% improvement). This work pioneers a new paradigm for precision-critical vision systems in photon-starved environments. Full article

Leaching represents a significant challenge for the mining industry due to its slow and incomplete kinetics under ambient conditions (20 °C, 1 atm) and its increased prevalence in global ore deposits. In this context, the use of hydrogen peroxide (H₂O₂) has proved to be a promising oxidizing agent for improving process efficiency. This article reviews the most recent breakthroughs in the use of H₂O₂ for chalcopyrite leaching, analyzing the experimental conditions that maximize copper extraction, including combinations with novel leachants such as organic systems, inorganic salts, and amino acids. In addition, the main challenges associated with the use of H₂O₂, such as its catalytic decomposition and thermal stability, are highlighted, along with strategies to overcome these limitations. Perspectives and challenges for its application are presented, emphasizing the need for hybrid and optimized approaches to integrate this oxidizing agent in sustainable hydrometallurgical processes. The objective of this paper is to make an exhaustive review of what has been published on chalcopyrite leaching in order to find ways to leach it in large quantities and in a simple way. Full article