Search Results (206)

Sludge electro-dewatering has emerged as a research hotspot in advanced sludge treatment due to its ability to effectively remove interstitial water that is difficult to separate by mechanical dewatering. This paper systematically reviews the fundamental principles, key influencing factors, evolution of electrode materials, and engineering applications of electro-dewatering technology. Emphasis is placed on analyzing the effects of sludge properties, electric field parameters, and electrochemical reactions on dewatering efficiency. The characteristics and applicable scenarios of three generations of electrode materials—from conventional metal electrodes and carbon-based materials to dimensionally stable anodes (DSA)—are summarized. Current challenges include insufficient electrode stability, the trade-off between energy consumption and efficiency, limited understanding of underlying micro-scale mechanisms, and difficulties in process scale-up. Future efforts should focus on the development of high-performance electrode materials, investigation of multi-field coupling enhancement mechanisms, establishment of machine learning-based intelligent control strategies, and engineering design of continuous electro-dewatering equipment to promote its large-scale application in sludge treatment and disposal. Full article

Microplastics (MPs) in wastewater treatment plants are predominantly retained in sewage sludge, making sludge processing a critical stage for MP transformation and potential pollutant release. However, the aging of polyethylene (PE) MPs and the release of MP-derived dissolved organic matter (MP-DOM) during sludge dewatering remain poorly understood. In this study, representative sludge conditioners were set up in dewatering experiments to investigate the changes in PE MP surface properties, pollutant-carrying potential, and MP-DOM release behavior. The results showed that sludge dewatering induced pronounced surface aging of PE MPs, including wrinkling, cracking, particle fragmentation, and the formation of polar oxygen-containing functional groups. These changes significantly increased the Cd adsorption potential of PE MPs, reaching 8228 ± 568 mg kg⁻¹. Lime conditioning promoted stronger fragmentation and a greater reduction in particle size than other conditionings, which likely increased the specific surface area. Meanwhile, a substantial release of PE MP-DOM was observed, with dissolved organic carbon concentrations in sludge process water being 2–30 times higher than those in deionized water. Fluorescence and molecular analyses showed that PE MP-DOM was dominated by protein-like and fulvic-like substances and also contained phthalates, fatty acids, and acetamide-based plasticizers. The magnitude and composition of PE MP-DOM release were strongly regulated by conditioner-induced pH and ionic strength. Alkaline conditions and increasing concentrations of Ca²⁺ (0.1–2.1 mol L⁻¹) and Fe³⁺ (0.006–0.6 mol L⁻¹) enhanced PE MP additive release. These findings demonstrate that sludge dewatering is an active process that accelerates PE MP aging and associated organic release. This work provides new insight into the environmental behavior of MPs during sludge treatment and offers a basis for developing sustainable sludge management. Full article

Background/Objectives: Municipal wastewater treatment plants (WWTPs) act as reservoirs for antibiotic-resistant bacteria, which pose a threat to global public health. In this study, we used whole-genome sequencing (WGS) to characterize antibiotic resistance genes (ARGs) and their association with mobile genetic elements (MGEs) in five multidrug-resistant (MDR) Escherichia coli isolates from dewatered sludge cake samples collected from a municipal WWTP in Cheongju, Republic of Korea. Methods: Susceptibility to nine antibiotics was evaluated via disk diffusion assay. Among the isolates exhibiting multidrug resistance (MDR) to three or more antibiotic classes, five isolates were randomly selected for whole-genome sequencing using the Illumina NovaSeqX platform. Additionally, we compared the genomic structures of five WWTP isolates with 35 environmental E. coli isolates from South Korea deposited in the NCBI pathogen database. ARGs and MGEs, including plasmids, integrons, and insertion sequences (ISs), were detected in the genome assemblies. Results: ARGs were differentially distributed between chromosomal and plasmid-derived contigs. Efflux pump-related genes were predominantly located on the chromosome across all isolates, whereas several beta-lactamase genes (e.g., bla_TEM-30 and bla_TEM-33), fluoroquinolone, and tetracycline resistance genes were localized on putative plasmid contigs. Furthermore, we characterized specific MGEs associated with these ARGs, including a class 1 integron gene cassette (dfrA17–aadA5–qacEΔ1–sul1) and an IS-mediated module (mph(A)–mrx–IS6100). Core-genome multilocus sequence typing (cgMLST) revealed that these MDR isolates represented diverse genetic lineages rather than a single clonal cluster. Conclusions: The results from this study highlight the necessity of enhanced post-treatment management of wastewater byproducts and WGS-based surveillance to mitigate the environmental spread of MDR bacteria. Full article

Municipal sewage sludge is an environmental liability but also an energy-rich biomass that can support circular economy resource recovery. Here, we benchmark thin-layer drying of dewatered municipal sewage sludge (sludge cake) (40 g; layer thickness ≤ 5 mm) under open-air, convective hot air (40–150 °C), and microwave (70–1200 W) conditions to quantify drying kinetics, hygienisation indicators, and a screening-level energy-use proxy. High-power microwave drying reduced the time to constant mass from 32 h (open air) and 25 h 05 min (40 °C convection) to 20 min (900 W) and 14 min 05 s (1200 W). Faecal indicators (total/thermotolerant coliforms and presumptive Escherichia coli) were below detection after ≥100 °C convection or ≥300 W microwave treatment, while mesophilic aerobes and sulfite-reducing Clostridium spp. decreased by ~3–4 log10 with increasing exposure. A dragonfly-optimised ε-support vector regression model (DA–SVR) predicted drying trajectories across modes (overall RMSE ≈ 0.79 percentage points; held-out RMSE ≈ 1.47; R² ≥ 0.99). Overall, microwave thin-layer drying coupled with DA–SVR decision support enables constraint-based screening of sewage–sludge conditioning windows for logistics and thermal valorisation pathways; the framework can be extended to incorporate additional analytical endpoints where available. Full article

The escalating production of sewage sludge presents a significant environmental challenge, while the construction industry simultaneously seeks sustainable raw materials to improve its circularity. This review analyses the technical and regulatory landscape for valorizing SS within the Latvian construction sector, set against the divergent strategies of its Baltic neighbours. While global research confirms the technical viability of using SS in fired-clay bricks and as a supplementary cementitious material (SCM), national management approaches differ starkly. Lithuania has adopted widespread incineration, and Estonia has focused on advanced composting. In contrast, Latvia’s national strategy is failing, with 51% of its 2024 sludge production diverted to “temporary storage”. This review identifies this crisis as a unique opportunity, arguing that incorporating dewatered digestate into fired-clay bricks is the most logical and economically viable pathway for Latvia, as it leverages existing industrial infrastructure. The primary obstacle to this circular solution is not technical but legal, specifically the lack of a national “End-of-Waste” (EoW) criterion for sludge-derived construction materials. Therefore, this article proposes a strategic roadmap for Latvia, centred on developing this essential legal framework, creating a national sludge characterization map, and initiating a pilot project to bridge the research-to-industry gap. Although Latvia is the primary focus of this review, the regulatory, infrastructural and material constraints analysed here are common in many small and mid-sized countries, making the insights applicable beyond the Latvian context. Full article

Plastic microfibers (PMFs) increasingly accumulate in wastewater treatment plants, impairing sludge dewatering and raising operational costs. This study combines a bibliometric analysis (2000–2025) with a critical review of the recent mechanistic literature to map the evolving research landscape on PMF–extracellular polymeric substance (EPS) interactions. The bibliometric trajectory (R² = 0.9786) underscores a paradigm shift towards a molecular understanding of the sludge matrix. Our synthesis of recent experimental studies reveals that PMF-induced interference is often driven by the selective adsorption of hydrophobic extracellular proteins, with one study reporting up to 32.5% sequestration. This has been linked to deteriorated dewatering, such as a 45% increase in capillary suction time (CST) under controlled conditions. Proteomic studies have identified more than 40 extracellular proteins with altered expression, directly linking PMFs to impaired sludge rheology. However, this review critically assesses the underlying evidence, highlighting significant methodological heterogeneity, a lack of standardized protocols, and a reliance on laboratory-scale models as key limitations that prevent broad generalization. By identifying these gaps, this work reframes the PMF–EPS research agenda, emphasizing the need for harmonized methods and multi-omics integration to transform mechanistic insights into robust biotechnological solutions for sustainable sludge management within a circular bioeconomy. Full article

Compost-derived humic acids (HAs) and fulvic acids (FAs) play an essential role in enhancing soil microbial diversity and activity by facilitating metabolic processes through electron transfer. Herein, the effect of bioleaching dewatered sludge (BDS) in comparison with filter press dewatered sludge (FDS) on the electron transfer capacity (ETC) of humic substances during composting was investigated as a novel attempt. A variety of characterization methods including UV-Vis, FTIR, 3D-EEM, and electrochemical measurements, were used to explore the change in humic substances during composting. The results indicated that bioleaching treatment significantly influenced the organic matter composition and hindered the accumulation of redox-active functional groups during composting. Notably, the ETC of HA increased by 24.07% in the FDS group but declined by 40.62% in the BDS group. This divergence stemmed from the organic matter loss during bioleaching, leading to reduced quinone-like and tryptophan-like substances associated with electron transfer in HA during composting. Furthermore, BDS showed lower pH, water content, and organic matter, but higher concentrations of ammonium nitrogen (${\mathrm{NH}}_4^{+}\text{-}\mathrm{N}$) and ammonia nitrogen ${\mathrm{NH}}_3^{-}\text{-}\mathrm{N}$, all of which potentially influenced humification efficiency. These findings not only clarify the electron-transfer dynamics of humic fractions but also highlight the importance of optimizing sludge pretreatment for improved composting performance and resource recovery. Full article

Vast quantities of liquid hydrocarbon and oil-containing wastes are generated and accumulate annually. Dewatering such sludges presents a significant technological challenge due to the high content of emulsified and chemically bound water. Consequently, the development of integrated approaches, particularly thermomechanical methods, have emerged as a promising strategy. These methods aim to disrupt the emulsion stability and enhance water evaporation efficiency. This study provides a theoretical basis for stabilizing the evaporation of the aqueous phase through mechanical agitation within boiling emulsions. A quantitative mathematical model is developed to identify critical conditions that prevent explosive boiling. Under intensive mixing, water globule diameters decrease by 80–85% within the first 5 s, while their settling time exceeds the dispersion time by hundreds of times—effectively inhibiting the accumulation of a critical aqueous-phase mass. Energy analysis reveals that, at a superheat temperature of 110 °C, the maximum permissible droplet diameter is approximately 0.5 mm; at 150 °C, it must not exceed 0.25 mm to avoid explosive boiling. To ensure safe operation, mixer rotational speeds of at least 100–200 rpm are required, with higher speeds (>200 rpm) necessary near 150 °C. The mechanical agitation modes proposed herein enable controlled, non-explosive evaporation of water from complex emulsions. Collectively, these findings lay a theoretical foundation for the industrial-scale deployment of thermomechanical dewatering technologies—offering a safer, more efficient pathway for managing challenging sludge streams. Full article

The rising volume of sludge production poses significant environmental threats. Sludge has a high moisture content (MC), which increases its disposal and transport expenses. On the other hand, sludge has low dewaterability due to its high concentration of soluble organic compounds. To reduce sludge production, understanding and improving preconditioning and mechanical dewatering are crucial for breakthroughs in advanced sludge dewatering. The sludge samples used in this analysis were obtained from the Sarabium municipal wastewater treatment plant, with a moisture content of 97% and a specific filtration resistance (SRF) of 9.15463 × 10¹⁵ m/kg. Sludge dewatering was enhanced by treating the samples chemically with ferric chloride, aluminum sulfate, Moringa olifera, and cationic polyacrylamide CPAM and physically with wood chips, slag, rice husk, and wheat straw. The experiments examined the sludge’s initial characterization (specific resistance to filtration (SRF) and time to filtrate (TTF)). To verify the structural characteristics (density), elemental composition, and the presence of various functional groups, a characterization investigation was conducted using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and energy-dispersive X-ray spectroscopy (EDS). The results showed that chemical conditioning with ferric chloride is better than aluminum sulfate and Moringa. Wood chips also provide better results for physical conditioning than rice husk, wheat straw, and slag. The reaction occurred at the carbonyl group, where FTIR showed more activated sites during SEM analysis, as evidenced by the FTIR results. Still, when CPAM was added to conditioned sludge, there was no difference in sludge dewatering performance, and the activated sites remained unchanged. Hence, this research found that mechanical sludge dewatering was improved by conditioning with ferric chloride (pH of 6 and dose of 0.12 g/g of dry solid) and wood chips (dose of 1.5 g/g of dry solid), which reduced sludge volume after dewatering by 82.5% under low pressure, which in turn minimizes transportation, energy, and handling costs. This study supports SDG 3 and SDG 6 by improving sludge dewatering efficiency and promoting sustainable wastewater management using natural wood chips. Full article

Dewatering of sewage sludge is a key operational element of wastewater treatment plants and has major economic implications, as it entails the costs of thickening, transport, and disposal. The aim of this study was to determine the influence of selected polyelectrolytes and their dosages on dewatering efficiency and to present an innovative, multicriteria method of result evaluation using radar charts. In this research, 10 different polyelectrolytes were assessed in terms of sludge dewaterability, considering conditioning parameters including Specific Resistance to Filtration (SRF), Capillary Suction Time (CST), and centrifugation performance. The results were presented in the form of radar charts, enabling both an overall evaluation of the effectiveness of each product and an assessment of their suitability for specific dewatering technologies, such as belt filter presses and centrifuges. The analysis showed that polyelectrolytes with higher cationic charge provided better dewatering performance. The proposed visualization method allows us to analyze the effects across different conditioners and technologies. The best sludge conditioning effect (maximum radar chart area) was achieved with Praestol 665, a polyelectrolyte with a high cationic charge level. This method is a practical tool for selecting the optimal agent for sewage sludge dewatering. Full article

Soil contamination by petroleum hydrocarbons represents a significant environmental challenge, especially in industrial and urban areas. This study evaluates the use of three industrial liquid by-products—sludge dewatering sidestream (SD), leftover yeast (LY), and secondary clarifier effluent (SC)—as biostimulant agents for the bioremediation of soils contaminated with gasoline and diesel mixtures. The novelty lies in applying these waste streams within a circular economy framework, with the added advantage that they can be injected directly into the subsurface. Microcosm tests were conducted over 20 weeks, analyzing the degradation of total petroleum hydrocarbons (TPHs) and their aliphatic and aromatic fractions using gas chromatography. The results show that all by-products improved biodegradation compared to natural attenuation. LY was the most effective, achieving 73.2% TPH removal, followed by SD (70.6%) and SC (65.4%). The greatest degradation was observed in short-chain hydrocarbons (C6–C16), while compounds with higher molecular weight (C21–C35) were more recalcitrant. In addition, aliphatic hydrocarbons showed greater degradability than aromatics in heavy fractions. Kinetic analysis revealed that the second-order model best fitted the experimental data, with higher correlation coefficients (R²) and more representative half-lives. Catalase enzyme activity also increased in soils treated with LY and SD, indicating higher microbial activity. Full article

The utilization of treated dredged sludge as a partial replacement for natural sand and gravel in construction projects offers a promising approach to reducing the exploitation of natural resources. The conventional vacuum preloading (VP) method, while widely used for soft soil improvement, is often associated with prolonged consolidation periods and high energy consumption in its later stages. Conversely, the electroosmosis (EO) technique is effective in enhancing drainage in low-permeability soft clays but is constrained by issues including anode corrosion, high operational costs, and uneven soil reinforcement. This study presents an experimental investigation into an alternating vacuum preloading and electroosmosis method for sludge treatment based on the underlying reinforcement theory. A series of laboratory model tests was conducted using a self-made vacuum–electroosmosis alternating test device. The reinforcement efficiency was assessed through the continuous monitoring of key performance indicators during the tests, including water discharge, surface settlement, electric current, electrode corrosion, and energy consumption. Post-test evaluations of the final soil shear strength and moisture content were also performed. The test results demonstrate that the alternating vacuum–electroosmosis yielded more significant improvement than their synchronous application. Specifically, the alternating vacuum–electroosmosis increased total water discharge by 46.1%, reduced final moisture content by 20.8%, and enhanced shear strength by 35.6% relative to the synchronous mode. Furthermore, an alternating VP-EO mode was found to be particularly advantageous during the electroosmosis phases, facilitating a more stable and sustained dewatering process. In contrast, the application of vacuum preloading alone resulted in inefficient performance during the later stages, coupled with relatively high energy consumption. Full article

In the last 32 years (1993–2024), the application of electric fields in soil management (soil electrokinetic, SEK) has undergone several stages of optimization and intensification. SEK has used both alternating current (AC) and direct current (DC). Numerous fields, including agriculture, sedimentation, phosphorus management in soil and sludge, fertilizer production, consolidation, reclaiming salt-affected soils, metal extraction, dewatering, remediation of contaminated soil (both organic, such as PFAS, and inorganic, such as heavy metals), and soil nutrient availability, have utilized the SEK concept. Numerous innovations were included in the SEK equipment’s design or combined with other biological, chemical, and physical processes. While we recently published a review article on soil electrokinetic/electroosmosis–vacuum systems for sustainable soil improvement and contaminant separation, the current study illustrates the role of applying the pressure-assisted soil electrokinetics technique and shows the effect of the opposite technique. Four points were used to show the function of pressure-assisted soil electrokinetics based on our analysis of six search engines from 1993 to 2024 (the previous 32 years), including (1) polluted soil remediation, (2) dewatering, (3) soil improvement, and (4) making soil ready for electrokinetic action by applying pressure. In contrast to other intensification methods (such as reverse polarity, pulsed electric field, and design change), we found very few publications addressing pressure-assisted soil electrokinetics throughout the literature search. Most investigations focused on the dewatering mechanism, despite the paucity of relevant papers. In contrast to conventional electrokinetic remediation, pump-assisted electrokinetic-flushing remediation increased the removal efficiencies of Cs⁺ and Co²⁺ from contaminated soil by 2% and 6%, respectively. Additionally, the results demonstrated that the pressured electro-osmotic dewatering approach outperformed the conventional electrokinetic techniques. At 40 kPa, hydraulic conductivity was reduced four-fold by electro-rehabilitation for alternative fuels, while at 100 kPa, it was reduced three-fold. It was also observed that pressure may be used to achieve the soil ready for electrokinetic action in order to guarantee proper operation. Since there are not many articles on the subject, future research may examine how pressure-assisted soil electrokinetics can be integrated with vacuum systems, reverse polarity mode, pulsed electric field mode, modifying the SEK design, overcoming the formation of cracks, etc. Full article

Coal sludge, a fine-grained by-product of hard coal benefit, comprises a mixture of coal particles and mineral and organic matter. Generated during sedimentation and dewatering processes in preparation plants, it is typically recovered as a semi-solid filter cake. The material has potential applications in energy production and, with appropriate processing and stabilization, could be utilized in geotechnical facilities. The strength properties defined by the internal friction angle and cohesion, as well as the deformation properties expressed by compressibility, are among the most important mechanical characteristics of soil. This article presents tests of coal sludge, for which the internal friction angle, cohesion, and oedometric primary and secondary moduli were determined. The material was prepared at its optimum moisture content and maximum dry density prior to testing. In the direct shear test, using a shear box of 6 × 6 cm, each sample was consolidated for 24 h under the applied vertical stress, under which it was subsequently sheared. The shear rate was constant at 0.01 mm/min, and the test was conducted up to 10% horizontal deformation. The vertical stresses applied ranged from 50 to 200 kPa. In the oedometer test, samples were prepared to fit the dimensions of the oedometer ring, and each subsequent load stage was applied after 24 h. The range of vertical stresses in this test was from 12.5 to 400 kPa. The results of the direct shear test (φ = 24°, c = 28 kPa) are similar to the strength parameters typically obtained for medium-cohesive soils, such as sandy silt (φ = 22°, c = 25 kPa. The results of the compressibility tests (0.89 MPa < M₀ < 6.35 MPa) correspond to values characteristic of organic soils, for example, organic silts (0.5 MPa < M₀ < 5 MPa). Moreover, analysis of the consolidation curves showed that up to a vertical stress of 100 kPa, coal sludge does not exhibit rheological behavior. The obtained results indicate that coal sludge, when compacted up to its optimum moisture content and to an adequate dry density, can be effectively utilized for geotechnical applications, such as the construction of isolation barriers, as a component of geotechnical mixtures, or as a sealing material for the reclamation of post-mining areas. Full article

The presence of organic matter can alter the dewatering characteristics of river-dredged silt and affect the dewatering efficiency. This study systematically compared the dewatering effects of cationic polyacrylamide (CPAM), ferric chloride (FeCl₃), and composite flocculant (CPAM + FeCl₃) for sludge with different organic matter contents by using the combined flocculation–electro-osmotic dewatering technology. The results show that the presence of organic matter significantly hinders the dewatering of silt. After the combined treatment of low-, medium-, and high-organic-matter river-dredging sludge with composite flocculants and electro-osmotic treatment, the final water content was 39.53%, 45.08%, and 47.28%, respectively. Compared with the use of CPAM alone, its dewatering efficiency increased by 66.98%, 5.39%, and 13.72%, respectively. Three-dimensional fluorescence spectroscopy analysis (3D-EEM) indicates that the combined dewatering of flocculation and electro-osmosis can improve the dewatering performance of sludge by promoting the transformation of organic matter. Scanning electron microscopy (SEM) analysis shows that under the action of the composite flocculant, the sludge particles aggregate significantly, and after electro-osmosis, the structure becomes more compact and channels are formed, which further improves the sludge dewatering efficiency. This study provides a theoretical basis for the optimization of dewatering processes for dredged silt with different organic matter contents. Full article