Search Results (904)

This study presents the design and microstructural investigation of a single-crystal (SX) Re-bearing high-entropy superalloy (HESA-X1) featuring a thermally stable γ–γ′–γ hierarchical microstructure. The alloy exhibits FCC γ nanoparticles embedded within L1₂-ordered γ′ precipitates, themselves distributed in a γ matrix, with the suppression of detrimental topologically close-packed (TCP) phases. To elucidate solidification behavior and phase stability, Scheil–Gulliver and TC-PRISMA simulations were conducted alongside SEM and XRD analyses. Near-atomic scale analysis in 3D using Atom Probe Tomography (APT) revealed pronounced elemental partitioning, with Re strongly segregating to the γ matrix, while Al and Ti were preferentially enriched in the γ′ phase. Notably, Re demonstrated a unique partitioning behavior compared to conventional superalloys, facilitating the formation and stabilization of γ nanoparticles during two-step aging (Ag-2). These γ nanoparticles significantly contribute to improved mechanical properties. Long-term aging (up to 200 h) at 750–850 °C confirmed exceptional phase stability, with minimal coarsening of γ′ and retention of γ nanoparticles. The coarsening rate constant K of γ′ at 750 °C was significantly lower than that of Re-free HESA, confirming the diffusion-suppressing effect of Re. These findings highlight critical roles of Re in enhancing microstructural stability by reducing atomic mobility, enabling the development of next-generation HESAs with superior thermal and mechanical properties for high-temperature applications. Full article

The eight new copper(II), nickel(II), zinc(II), and iron(III) coordination compounds [Cu(L)Cl]₂ (1), [Cu(L)Br]₂ (2), [Cu(L)(NO₃)]₂ (3), [Cu(phen)(L)]NO₃ (4), [Ni(HL)₂](NO₃)₂·H₂O (5), [Ni(HL)₂]Cl₂ (6), [Zn(L)₂]·0.125H₂O (7), and [Fe(L)₂]Cl (8), where HL stands for 2-benzoylpyridine 4-allylthiosemicarbazone, were synthesized and characterized. ¹H, ¹³C NMR, and FTIR spectroscopies were used for characterization of the HL thiosemicarbazone. The elemental analysis, the FTIR spectroscopy, and the study of molar electrical conductivity were used for characterization of the coordination compounds 1–8. Also, the crystal structures of HL, its salts ([H₂L]Cl; [H₂L]NO₃), and complexes 1, 3, 5, 7, and 8 were determined using single-crystal X-ray diffraction analysis. Complexes 5, 7, 8 have mononuclear structures, while copper(II) complexes 1 and 3 have a dimeric structure with the sulfur atoms of the thiosemicarbazone ligand bridging two copper atoms together. Thiosemicarbazone HL and the complexes manifest antibacterial and antifungal activities. The studied substances are more active towards Gram-negative bacteria than towards Gram-positive bacteria and fungi. Complex 1 is the most active one towards Gram-positive bacteria and C. albicans, while the introduction of 1,10-phenanthroline into the inner sphere enhances the activity towards Gram-negative bacteria. Thiosemicarbazone and complexes 6 and 7 manifest antiradical activity that exceeds the activity of Trolox. HL and complex 1 manifest antiproliferative activity towards HL-60 cancer cells which exceeds the activity of their analogs with 2-formyl-/2-acetylpyridine 4-allylthiosemicarbazone. Full article

This article presents a review of the composition optimization progress of nickel-based single crystal (SC) superalloy design in recent years in order to obtain better high-temperature performance for the development of the aviation industry. The influence of alloying elements on the creep resistance, microstructure characteristics, oxidation resistance, castability, density, and cost of superalloys is analyzed and discussed. In order to obtain better high-temperature performance, the content of refractory elements (Ta + Re + W + Mo) and Co was increased gradually. The addition of Ru was added in the fourth-generation nickel-based SC superalloy to stabilize the microstructures and suppress the precipitation of the topologically close-packed (TCP) phase. However, the content of the antioxidant element Cr significantly decreased, while the synergistic effect of Al, Cr, and Ta received more attention. Therefore, synergistic effects should also receive more attention to meet the practical needs of reducing the content of refractory elements to reduce costs and density in future single crystal alloy designs without compromising critical performance. Full article

Searching for new and efficient transfer hydrogenation catalysts, a series of new organometallic ruthenium(II)-arene complexes of the formulae [Ru(η⁶-p-cymene)(L)Cl][PF₆] (1–8) and [Ru(η⁶-p-cymene)(L)Cl][Ru(η⁶-p-cymene)Cl₃] (9–11) were synthesized and fully characterized. These were prepared from the reaction of pyridine–quinoline and biquinoline-based ligands (L) with [Ru(η⁶-p-cymene)(μ-Cl)Cl]₂, in 1:2 and 1:1, metal (M) to ligand (L) molar ratios. Characterization includes a combination of spectroscopic methods (FT-IR, UV-Vis, multi nuclear NMR), elemental analysis and single-crystal X-ray crystallography. The pyridine–quinoline organic entities encountered, were prepared in high yield either via the thermal decarboxylation of the carboxylic acid congeners, namely 2,2′-pyridyl-quinoline-4-carboxylic acid (pqca), 8-methyl-2,2′-pyridyl-quinoline-4-carboxylic acid (8-Mepqca), 6′-methyl-2,2′-pyridyl-quinoline-4-carboxylic acid (6′-Mepqca) and 8,6′-dimethyl-2,2′-pyridyl-quinoline-4-carboxylic acid (8,6′-Me₂pqca), affording the desired ligands pq, 8-Mepq, 6′-Mepq and 8,6′-Me₂pq, or by the classical Friedländer condensation, to yield 4,6′-dimethyl-2,2′-pyridyl-quinoline (4,6′-Me₂pq) and 4-methyl-2,2′-pyridyl-quinoline (4-Mepq), respectively. The solid-state structures of complexes 1–4, 6, 8 and 9 were determined showing a distorted octahedral coordination geometry. The unit cell of 3 contains two independent molecules (Ru-3), (Ru′-3) in a 1:1 ratio, due to a slight rotation of the arene ring. All complexes catalyze the transfer hydrogenation of acetophenone, using 2-propanol as a hydrogen donor in the presence of KOiPr. Among them, complexes 1 and 5 bearing methyl groups at the 8 and 4 position of the quinoline moiety, convert acetophenone to 1-phenylethanol quantitatively, within approximately 10 min with final TOFs of 1600 h⁻¹. The catalytic performance of complexes 1–11, towards the transfer hydrogenation of p-substituted acetophenone derivatives and benzophenone, ranges from moderate to excellent. An inner-sphere mechanism has been suggested based on the detection of ruthenium(II) hydride species. Full article

In this study, 3-chlorothiophene-2-carboxylic acid (HL) was used as a main ligand to successfully synthesize four novel complexes: [Cu(L)₂(Py)₂(OH₂)₂] (1), [Co(L)₂(Py)₂(OH₂)₂] (2) (Py = pyridine), [{Ni(L)₂(OH₂)₄}₂{Ni(L)(OH₂)₅}]L•5H₂O (3), and [{Co(L)₂(OH₂)₄}₂{Co(L)(OH₂)₅}]L•5H₂O (4). All four compounds were identified by elemental analysis and ESI mass spectrometry, and subsequently characterized by IR spectroscopy, UV-visible diffuse reflectance spectroscopy, electron paramagnetic resonance spectroscopy, thermogravimetric analysis, single-crystal X-ray crystallography, and cyclic voltammetry. X-ray analyses revealed that complexes 1 and 2 exhibit a centrosymmetric pseudo-octahedral coordination geometry; the copper (II) and cobalt (II) metal ions, respectively, are located at the crystallographic center of inversion. The coordination sphere of the copper (II) complex is axially elongated in accordance with the Jahn–Teller effect. Intriguingly, for charge neutrality, compounds 3 and 4 crystallized as three independent mononuclear octahedrally coordinated metal centers, which are two $\left[\mathrm{M}{\mathrm{L}}_2{\left({\mathrm{O}\mathrm{H}}_2\right)}_4\right]$ complex molecules and one ${\left[\mathrm{M}\mathrm{L}{\left({\mathrm{O}\mathrm{H}}_2\right)}_5\right]}^{+}$ complex cation (M = ${\mathrm{N}\mathrm{i}}^{\mathrm{I}\mathrm{I}}$ and ${\mathrm{C}\mathrm{o}}^{\mathrm{I}\mathrm{I}}$, respectively), with the ligand anion ${\mathrm{L}}^{-}$ serving as the counter ion. The anticancer activities of these complexes were systematically assessed on human leukemia K562 cells, lung cancer A549 cells, liver cancer HepG2 cells, breast cancer MDA-MB-231 cells, and colon cancer SW480 cells. Among them, complex 4 shows significant inhibitory effects on leukemia K562 cells and colon cancer SW480 cells. Full article

Coumarin and cytisine and their derivatives have significant biological activity. In addition, the electronic properties of coumarin derivatives are very sensitive to the molecular environment, which allows for their use as sensors for bioluminescent imaging. Due to the fact that cytisine exhibits high activity in binding to nicotinic acetylcholine receptors, a compound combining parts of cytisine and coumarin may have a broader spectrum of biological activity and also act as a photoactive element for promising use in optoelectronic devices. This article reports the synthesis of a crystalline cytisine–coumarin complex (IUPAC: N-(2-oxo-2H-chromene-3-carbonyl)cytisine), along with the results of both theoretical and experimental investigations of its structural and electronic properties. The structure of this new compound was established on the basis of X-ray diffraction and Fourier transform infrared spectroscopy data and was confirmed through density functional theory calculations using periodic crystal and single-molecule approaches. Interpretations of the IR absorption peaks and the atomic patterns of the vibrational modes are given. The electronic band structure and the contributions of individual atoms to the electronic density of states are analyzed. The structural and optical properties considered may be useful for quality control of the compound and for studying similar matrices. Full article

Heavier element analogues of a ketone, a C=O double-bond compound, have been fascinating compounds from the viewpoint of main-group element chemistry because of their unique structural features and reactivity as compared with those of a ketone, which plays an important role in organic chemistry. We will report here the synthesis of diorgano-stannanethione and stannaneselone featuring tin–chalcogen double bonds, which are the heavy-element analogues of a ketone. The newly obtained stannaneselone has been structurally characterized by spectroscopic analyses and single-crystal X-ray diffraction (SC-XRD) analysis, showing the short Sn–Se bond length featuring π-bond character. The obtained bis(ferrocenyl)stannanechalcogenones were found to undergo [2+4]cycloaddition reactions with 2,3-dimethyl-1,3-butadiene, affording the corresponding six-membered ring compound. Notably, thermolysis of the [2+4]cycloadduct of the stannaneselone regenerated the stannaneselone via the retro[2+4]cycloaddition, whereas the sulfur analogue was thermally very stable. Full article

The objective of this work was the synthesis and characterization of novel, insensitive high explosives. 1-hydroxy-5-methyltetrazole served as both a scaffold and anion for preparing various nitrogen-rich energetic salts. The compounds were characterized using ¹H and ¹³C NMR spectroscopy, high-resolution mass spectrometry, elemental analysis, low-temperature single-crystal X-ray diffraction, and IR spectroscopy. Thermal stability was investigated via differential thermal analysis (DTA). Sensitivities towards mechanical stimuli were measured using a BAM drop hammer for impact sensitivity and a BAM friction apparatus for friction sensitivity, employing one of six testing procedures. Energetic performance parameters were calculated using the EXPLO5 code, incorporating room-temperature X-ray densities and solid-state heats of formation obtained via CBS-4M calculations using the Gaussian 16 program. Full article

A series of para-trifluoromethoxy-substituted and fluorobenzhydryl-functionalized 1,2-bis(imine)acenaphthene ligands: 1-[2,6-{(4-F-C₆H₄)₂CH}₂-4-F₃COC₆H₂N]-2-(ArN)C₂C₁₀H₆ (Ar = 2,6-Me₂C₆H₃ L1, 2,6-Et₂C₆H₃ L2, 2,6-iPr₂C₆H₃ L3, 2,4,6-Me₃C₆H₂ L4, 2,6-Et₂-4-MeC₆H₂ L5), were synthesized and used to generate their corresponding nickel(II) bromide complexes (Ni1–Ni5). Elemental analysis, ¹⁹F NMR, and FT-IR spectroscopy were employed to characterize these five nickel complexes. Single-crystal X-ray diffraction of Ni2 and Ni4 confirmed distorted tetrahedral geometries. Upon activation with either EtAlCl₂ (ethylaluminum dichloride) or EASC (ethyl aluminum sesquichloride), these complexes showed exceptional high activities (up to 22.0 × 10⁶ g PE mol⁻¹ (Ni) h⁻¹) and remarkable thermal stability (4.82 × 10⁶ g PE mol⁻¹(Ni) h⁻¹ at 80 °C) towards ethylene polymerization. The resulting polyethylenes are highly branched, with the type and extent of branches tunable by temperature, solvent, and co-catalyst choice. Moreover, these polymers demonstrated excellent tensile strength (σ_b up to 20.7 MPa) and elastic recovery (up to 58%), characteristic of thermoplastic elastomers (TPEs). These results highlight the dual role of trifluoromethoxy and fluorobenzhydryl groups in enhancing catalytic performance and polymer properties. Full article

Many granitic enclaves are developed in the volcanic channel of the Xiangshan volcanic basin. To explore their genesis, this study examined the petrography, geochemistry, LA-ICP-MS zircon U–Pb chronology, and zircon Hf isotopes of the granitic enclaves and compared them with the porphyroclastic lavas. In general, the granitic enclaves and porphyroclastic lavas have similar structures, and the rock-forming minerals and accessory minerals have relatively close compositions. In terms of rock geochemical characteristics, the granitic enclaves are richer in silicon and alkalis but have lower abundances of aluminum, magnesium, iron, and calcium than the porphyroclastic lavas. Rb, Th, K, Sm, and other elements are more enriched, whereas Ba, Ti, Nb, P, and other elements are more depleted. The granitic enclaves have lower rare earth contents (195.53 × 10⁻⁶–271.06 × 10⁻⁶) than the porphyroclastic lavas (246.67 × 10⁻⁶–314.27 × 10⁻⁶). The rare earth element distribution curves of the two are generally consistent, both right-leaning, and enriched with light rare earth patterns. The weighted average zircon U–Pb ages of two granitic enclave samples were 135.45 ± 0.54 Ma (MSWD = 0.62, n = 17) and 135.81 ± 0.60 Ma (MSWD = 0.40, n = 20), respectively, which are consistent with the weighted average age of a single porphyroclastic lava sample of 134.01 ± 0.53 Ma (MSWD = 2.0, n = 20). The zircons of the two kinds of rocks crystallize at almost the same temperature. The consistent trend of the rare earth element distribution curve of zircons in the granitic enclaves and the porphyroclastic lava samples indicates that the zircons of the two samples were formed in the same stage. The formation process of granitic enclaves may be that the lower crustal melt is induced to rise, and the crystallization differentiation occurs in the magma reservoir and is stored in the form of crystal mush, forming a shallow crystal mush reservoir. The crystal mush reservoir is composed of a large number of rock-forming minerals such as quartz, feldspar, and biotite, as well as accessory mineral crystals such as zircon and flowable intergranular melt. In the later stage of magma high evolution, a small and short-time magmatic activity caused a large amount of crystalline granitic crystal mush to pour into the volcanic pipeline. In the closed system of volcanic pipeline, the pressure and temperature decreased rapidly, and the supercooling degree increased, and the immiscibility finally formed pale granitic enclaves. Full article

Co-doping at Ba and Ti sites with double rare-earth elements has proven an effective strategy for enhancing the dielectric properties of BaTiO₃ ceramics. Among intermediate-sized rare-earth ions, Tb and Ho exhibit amphoteric behavior, occupying both Ba and Ti sites. Investigating the site occupation, defect chemistry, and dielectric effects of Tb and Ho in BaTiO₃ is therefore valuable. In this work, Tb/Ho-co-doped BaTiO₃ ceramics with the composition (Ba_1−xTb_x)(Ti_1−xHo_x)O₃ (x = 0.01~0.10) were fabricated at 1400 °C via solid-state reaction, and their solid solubility and crystal structures are confirmed. Microstructure, dielectric properties, photoluminescence, and valence states of samples with a single phase were systematically studied. Both the lattice parameter a and unit cell volume increase with doping level. The ceramic with x = 0.02 meets the X5S dielectric specification. Ho and Tb ions both demonstrate amphoteric site occupancy: Ho exists solely as Ho³⁺ at both Ba and Ti sites, while Tb exhibits mixed valence states as Ba-site Tb³⁺ and Ti-site Tb⁴⁺. As the doping content increases, the concentration of Tb⁴⁺ at Ti sites decreases, and the quantity of Ba-site Ho³⁺ ions initially increases to a maximum before decreasing. Defect compensation mechanisms within the samples are also discussed. Full article

A nitro-derivative of fenamic acid (4′–nitro–fenamic acid) was synthesized and used as ligand for the synthesis of four Co(II) complexes in the absence or presence of the N,N′-donors 2,2′–bipyridylamine, 1,10–phenanthroline and 2,9–dimethyl–1,10–phenanthroline. The characterization of the resultant complexes was performed with diverse techniques (elemental analysis, molar conductivity measurements, IR and UV-vis spectroscopy, single-crystal X-ray crystallography). The biological evaluation of the compounds encompassed (i) antioxidant activity via hydrogen peroxide (H₂O₂) reduction and free radical scavenging; (ii) antimicrobial screening against two Gram-positive and two Gram-negative bacterial strains; (iii) interactions with calf-thymus (CT) DNA; (iv) cleavage of supercoiled pBR322 plasmid DNA (pDNA), in the dark or under UVA/UVB/visible light irradiation; and (v) binding affinity towards bovine and human serum albumins. The antioxidant activity of the compounds against 2,2′–azinobis–(3–ethylbenzothiazoline–6–sulfonic acid) radicals and H₂O₂ is significant, especially in the case of H₂O₂. The complexes exhibit adequate antimicrobial activity against the strains tested. The complexes interact with CT DNA through intercalation with binding constants reaching a magnitude of 10⁶ M⁻¹. The compounds have a significantly enhanced pDNA-cleavage ability under irradiation, showing promising potential as photodynamic therapeutic agents. All compounds can bind tightly and reversibly to both albumins tested. Full article

It has been proven that silica fume (SF), which is a by-product from the manufacturing of single-crystal silicon, is beneficial for enhancing the mechanical properties, durability, and workability of geopolymers, as it can be quickly dissolved and form silicate-based cementitious phases in alkaline environments. However, the reinforcement mechanism of SF on geopolymer remains unclear due to the chemical complexity of geopolymer and the variety of SF types. Additionally, the solubility of calcite in an alkali environment is quite limited, and thus the formation of the amorphous calcium-based gels will be thwarted due to the lack of soluble calcium ions. Most importantly, with the development of the single-crystal industry, the amorphous silica content, crystallinity, and trace elements of SF itself have changed, which blocks the understanding of the activation mechanism of geopolymers combined with SF and insoluble calcite. To unveil the underlying modification mechanisms of SF on geopolymer materials along with insoluble calcite, in this study, two types of SF were used as the fly ash replacement in a fly ash/limestone system to prepare geopolymer materials. The reinforcement effect significantly depends on the SF types even with similar particle size and chemical compositions. The results indicate that the mechanical properties of geopolymer materials modified with SFs are not only governed by the ratio and contents of Si, Ca, Al, and Mg in SFs but also depend on the crystallinity and activity of the SFs. The hydration products could be varied according to the reaction environment. The research results not only contribute to the optimization design and application of geopolymer materials but also pave new pathways for the upcycling use of solid wastes such as SF, low-grade fly ash, or even other aluminosilicate solid wastes to achieve sustainable development. Full article

In this paper, we perform crystal plasticity finite element (CPFE) simulations of spherical nanoindentation to extract the indentation stress–strain (ISS) curve for a single-crystalline copper. The load–displacement curves on the Cu (010) surface at incremental indentation depths are obtained. Surface pile-up topography is explored and characterized by the activated slip systems on the indented surface and stress distribution on the cross-section to reveal the crystal anisotropy. And the effect of indentation depth on the stiffness and surface pile-up height is further analyzed. Finally, the zero point is defined, and the indentation stress–strain (ISS) curve is extracted from load–displacement curves. The validity of the ISS curve is demonstrated for crystalline copper materials by comparing measured results published in the literature. Full article

Four new arene–ruthenium(II) complexes [(η⁶-p-cymene)RuCl(dpm)], where dpm are hexa-(L3–L5) and meso-substituted (L6) dipyrromethene ligands, were synthesized. These ligands and the corresponding complexes were thoroughly characterized by elemental analysis and spectroscopic techniques (MS, IR, ¹H, ¹³C NMR, and UV–vis), and the structures of one ligand and three ruthenium complexes were determined by X-ray single-crystal analysis. The DNA-binding ability of the Ru-3–Ru-6 complexes was evaluated by UV–vis DNA titration. Compound Ru-3 exhibited the highest binding energy, outperforming the complexes containing a dipyrrin ligand substituted by chlorides (Ru-4 and Ru-5) or a meso-substituted dipyrrin (Ru-6). Molecular docking revealed that the hypothetical Ru-1 and Ru-2 complexes, which contain iodide ligands in the dipyrrin structures, showed higher DNA-binding affinities than Ru-3. Computational calculations supported the experimental results, confirming that Ru-3 has a higher affinity for DNA than the other complexes. Full article