Search Results (465)

High-performance waterproof and breathable nanofiber membranes (WBNMs) are in great demand for various advanced applications. However, the fabrication of such membranes often relies on fluorinated materials or involves complex preparation processes, limiting their practical use. In this study, we present an innovative approach by utilizing silicon-containing polyurethane (SiPU) as a single-component, fluorine-free raw material to prepare high-performance WBNMs via a simple one-step electrospinning process. The electrospinning technique enables the formation of SiPU nanofibrous membranes with a small maximum pore size (d_max) and high porosity, while the intrinsic hydrophobicity of SiPU imparts excellent water-repellent characteristics to the membranes. As a result, the single-component SiPU WBNM exhibits superior waterproofness and breathability, with a hydrostatic pressure of 52 kPa and a water vapor transmission rate (WVTR) of 5798 g m⁻² d⁻¹. Moreover, the optimized SiPU-14 WBNM demonstrates outstanding mechanical properties, including a tensile strength of 6.15 MPa and an elongation at break of 98.80%. These findings indicate that the single-component SiPU-14 WBNMs not only achieve excellent waterproof and breathable performance but also possess robust mechanical strength, thereby enhancing the comfort and expanding the potential applications of protective textiles, such as outdoor apparel and car seats. Full article

Superhydrophobic and superoleophilic nanofibrous or microfibrous membranes are regarded as ideal oil/water separation materials owing to their controllable porosity, superior separation efficiency, and ease of operation. However, developing efficient, scalable, and environmentally friendly strategies for fabricating such membranes remains a significant challenge. In this study, isotactic polypropylene (iPP) fibrous membranes with morphologies ranging from ellipsoidal stacking to microfiber stacking were successfully fabricated via a multistage stretching extrusion and leaching process using in situ microfibrillar composites (MFCs). The results establish a significant relationship between microfiber morphology and membrane oil adsorption performance. Compared with membranes formed from high-aspect-ratio microfibers, those comprising short microfibers feature larger pores and a more open structure, which enhances their oil adsorption capacity. Among the fabricated membranes, the iPP membrane with an ellipsoidal stacking morphology exhibits optimal performance, achieving a porosity of 65% and demonstrating both hydrophobicity and superoleophilicity, with a silicone oil adsorption capacity of up to 312.5%. Furthermore, this membrane shows excellent reusability and stability over ten adsorption–desorption cycles using chloroform. This study presents a novel approach leveraging in situ microfibrillar composites to prepare high-performance oil/water separation membranes in this study, underscoring their considerable promise for practical use. Full article

Semen collection is an important component of conservation and animal husbandry. Semen quality is generally improved using voluntary collection methods, particularly artificial vaginas (AVs). Most commercially available AVs are tube-shaped with few species-specific design augmentations. As genitalia are highly variable across taxa, incorporating species-specific genital morphologies into AV designs may enhance collected semen quality. We compared dolphin semen quality using: (1) silicone bioinspired artificial vaginas (BAVs) that reflect the internal shape of dolphin vaginas, and (2) manual stimulation. Sperm motility and kinematic parameters of five bottlenose dolphins (Tursiops sp.) were assessed using computer-aided sperm analysis (CASA). Sperm collected using BAVs showed non-significant increases in median progressive and rapid motility, and increases in median and mean linear motility, supporting a sexual selection functional hypothesis for the biodiverse vaginal folds unique to whales, dolphins, and porpoises. Sperm concentration decreased with BAV collection, while no consistent trends were detected in volume, pH, velocity, or plasma membrane integrity. Modifications to AVs for other species that incorporate genital morphologies may also optimize collected semen quality for application to artificial insemination. Full article

Membrane fouling poses a significant challenge in the widespread adoption and cost-effective operation of membrane technology. Among different strategies to mitigate fouling, dynamic membrane (DM) technology has emerged as a promising one for effective control and mitigation of membrane fouling. Silicon carbide (SiC) membranes have attracted considerable attention as membrane materials due to their remarkable advantages, yet membrane fouling is still inevitable in challenging separation tasks, such as oil-in-water (O/W) emulsion separation, and thus effective mitigation of membrane fouling is essential to maximize their economic viability. This study investigates the use of pre-deposited oxide DMs to mitigate the fouling of SiC membranes during the separation of O/W emulsions. Among five screened oxides (Fe₂O₃, SiO₂, TiO₂, ZrO₂, Al₂O₃), SiO₂ emerged as the most effective DM material due to its favorable combination of particle size, negative surface charge, hydrophilicity, and underwater oleophobicity, leading to minimized oil droplet adhesion via electrostatic repulsion to DM surfaces and enhanced antifouling performance. Parameter optimization in dead-end mode revealed a DM deposition amount of 300 g/m², a transmembrane pressure (TMP) of 0.25 bar, and a backwashing pressure of 2 bar as ideal conditions, achieving stable oil rejection (~93%) and high pure water flux recovery ratios (FRR, >90%). Cross-flow filtration outperformed dead-end mode, maintaining normalized permeate fluxes of ~0.4–0.5 (cf. ~0.2 in dead-end) and slower FRR decline, attributed to reduced concentration polarization and enhanced DM stability under tangential flow. Optimal cross-flow conditions included a DM preparation time of 20 min, a TMP of 0.25 bar, and a flow velocity of 0.34 m/s. The results establish SiO₂-based DMs as a cost-effective strategy to enhance SiC membrane longevity and efficiency in O/W emulsion separation. Full article

Industrial technologies for processing tungsten concentrates using soda roasting or autoclave leaching are based on the production of alkaline sodium tungstate solutions that contain impurities such as silicon, phosphorus, arsenic, and others. The purification of these solutions from impurities requires the neutralization of excess soda or alkali with inorganic acids, which leads to the formation of chloride and sulfate effluents that are subsequently discharged into waste repositories. An analysis was carried out on existing methods for the production and processing of sodium tungstate solutions using HNO₃ and NH₃, as well as extraction and sorption techniques involving anion exchange resins. Currently, processes such as nanofiltration, reverse osmosis, and electrodialysis are being applied for water purification and the treatment of sulfate and chloride effluents. These processes employ various types of industrially manufactured membranes. For the purpose of electrodialysis, a two-compartment electrodialyzer setup was employed using cation-exchange membranes of the MK-40 (Russia) and EDC1R (China) types. The composition and structure of sodium tungstate, used as the starting reagents, were analyzed. Based on experiments conducted on a laboratory-scale unit with continuous circulation of the catholyte and anolyte, dependencies of various parameters on current density and process duration were established. Stepwise changes in the anolyte pH were recorded, indirectly confirming changes in the composition of the Na₂WO₄ solution, including the formation of polytungstates of variable composition and the production of H₂WO₄ via electrodialysis at pH < 2. The resulting tungstic acid solutions were also analyzed. The conducted studies on the processing of sodium tungstate solutions using electrodialysis made it possible to obtain alkaline solutions and tungstic acid at a current density of 500–1500 A/m², without the use of acid for neutralization. Yellow tungstic acid was obtained from the tungstic acid solution by evaporation. Full article

The proper usage of a bandwidth-limited imaging bolometer for the measurement of the lateral temperature profile of microstructures in Silicon-Carbide (SiC) is analyzed. The SiC spectral emissivity, ${ϵ}_{SiC}\left(\lambda \right)$, has a dip at $\lambda \sim 12$$\mathsf{\mu }$m, which is in the band of a typical commercially available instrument and complicates the selection of the value of the equivalent emissivity, ${ϵ}_{eq,SiC}$, in the instrument settings. The impact is analyzed by deduction using simulation, and by experimental validation. Membranes of 3C-SiC of 1000 $\mathsf{\mu }$m diameter and 3 $\mathsf{\mu }$m thickness have been fabricated on Si wafers, with integrated poly-SiC resistors for both membrane heating and on-membrane temperature measurement for calibration purposes. The optimum setting was found as ${ϵ}_{eq,SiC}$ = 0.705 ± 0.025 by deduction and as ${ϵ}_{eq,SiC}$ = 0.66 ± 0.06 by experimental validation in the temperature range 120 °C to 400 °C. The apparent temperature coefficient of emissivity, $TCE<$ 2 × 10⁻⁴ °C⁻¹ is due to the shift of the Wien peak wavelength relative to the instrument’s sensitivity band. Full article

Long-term ECMOs are expected to be put into practical use in order to prepare for the next emerging severe infectious diseases after the novel coronavirus pandemic in 2019–2023. While polypropylene (PP) and polymethylpentene (PMP) are currently the mainstream materials for the hollow fiber membranes of ECMO, the PP membrane coated with a silicone layer on the outer surface has also been commercialized. In this study, we sought a method to accurately observe the detailed pore morphologies of the PP membrane by suppressing irreversible changes in the morphology in SEM observation, which is a general-purpose observation with higher resolution. As a result, the convex surface morphologies of the PP membrane, which was a non-conductive porous structure, were confirmed in detail by utilizing the lower secondary electron image (LEI) mode (FE-SEM, JSM-7610F, JEOL Ltd., Tokyo, Japan) at low acceleration voltage, low magnification, and long working distance, to minimize morphological alterations caused by osmium (Os) sputtering. On the other hand, although the sputter-coating on non-conductive samples is mandatory for imaging morphologies with SEM, the non-sputtering method is also worthwhile for porous and fragile structures such as this sample to minimize morphological alterations. Furthermore, we propose a method to confirm the morphology of the deep part of the sample by utilizing the secondary electron image (SEI) mode at an appropriate acceleration voltage and high magnification with higher resolution. Full article

Silicon, being the fundamental material for modern semiconductor devices, has seen continuous advancements to enhance its electrical and mechanical properties. Strain engineering is a well-established technique for improving the performance of silicon-based devices. In this paper, we propose a simple method for inducing and permanently maintaining strain in silicon through pure physical bending. By subjecting the silicon substrate to a controlled bending process, we demonstrate the generation of strain levels that persist even after the removal of external stress, with a maximum strain value of 0.4%. We present a comprehensive study of the mechanics behind this phenomenon, a full finite element mechanical model, and experimental verification of the bending-induced strain in Si membranes using electron backscatter diffraction measurements. Our findings show the potential of this approach for strain engineering in high-performance silicon-based technologies without resorting to complex and expensive fabrication techniques. Full article

This paper presents a novel silicon-based piezoresistive pressure sensor composed of a silicon layer with sensing elements and a glass cover for hermetic packaging. Unlike conventional designs, this study employs numerical simulation to analyze the influence of varying roughness levels of the sensitive membrane on the sensor’s output response. Simulation results demonstrate that pressure sensors with smoother sensitive membranes exhibit superior performance in terms of sensitivity (5.07 mV/V/MPa), linearity (0.67% FS), hysteresis (0.88% FS), and repeatability (0.75% FS). Furthermore, an optimized process for controlling membrane roughness was achieved by adjusting the concentration of the etchant solution. Experimental results reveal that a membrane roughness of 35.37 nm was attained under conditions of 80 °C and 25 wt% TMAH. Additionally, the fabrication process of this piezoresistive pressure sensor was significantly simplified and cost-effective due to the adoption of a backside wet etching technique. The fabricated sensor demonstrates excellent performance metrics, including a sensitivity of 5.07 mV/V/MPa, a full-scale (FS) output of 101.42 mV, a hysteresis of 0.88% FS, a repeatability of 0.75% FS, and a nonlinearity of 0.67% FS. These results indicate that the proposed sensor is a promising tool for precise pressure measurement applications, offering both high performance and cost efficiency. This study not only advances the understanding of the impact of membrane roughness on sensor performance but also provides a practical and scalable fabrication approach for piezoresistive pressure sensors. Full article

Carbon molecular sieve (CMS) membranes demonstrate considerable advantages and significant potential in the separation of CO₂ and CH₄. Nevertheless, current research predominantly emphasizes the enhancement of CMS membranes through the incorporation of rigid structures and chain spatial stacking. The role of flexible structures in this context remains inadequately understood. To address this gap, we introduced long-chain polydimethylsiloxane (PDMS) and copolymerized it to synthesize polyimide that combines rigid and flexible frameworks. This approach enabled us to investigate the impact of flexible structures on the structure and properties of carbon membranes by varying the PDMS content. The findings indicated that flexible PDMS significantly influenced the thermal decomposition behavior of polyimide and facilitated in situ silicon doping within the carbon membranes, thereby modifying the pore characteristics of the carbon film. Specifically, with a 10% addition of PDMS, the CO₂ permeability of the CMS membrane reached 9556 Barrer, representing an enhancement of 103.9% and surpassing the 2019 upper bound for CO₂/CH₄ separation. Furthermore, the effect of pyrolysis temperature was also examined. Ultimately, this study offers a novel perspective on regulating the structural and performance characteristics of carbon membranes through the integration of long-chain flexible structures. Full article

Nanotubes (NTs) are nanosized tube-like structured materials made from various substances such as carbon, boron, or silicon. Carbon nanomaterials (CNMs), including carbon nanotubes (CNTs), graphene/graphene oxide (G/GO), and fullerenes, have good interatomic interactions and possess special characteristics, exploitable in several applications because of the presence of sp2 and sp3 bonds. Among NTs, CNTs are the most studied compounds due to their nonpareil electrical, mechanical, optical, and biomedical properties. Moreover, single-walled carbon nanotubes (SWNTs) have, in particular, demonstrated high ability as drug delivery systems and in transporting a wide range of chemicals across membranes and into living cells. Therefore, SWNTs, more than other NT structures, have generated interest in medicinal applications, such as target delivery, improved imaging, tissue regeneration, medication, and gene delivery, which provide nanosized devices with higher efficacy and fewer side effects. SWNTs and multi-walled CNTs (MWCNTs) have recently gained a great deal of attention for their antibacterial effects. Unfortunately, numerous recent studies have revealed unanticipated toxicities caused by CNTs. However, contradictory opinions exist regarding these findings. Moreover, the problem of controlling CNT-based products has become particularly evident, especially in relation to their large-scale production and the nanosized forms of the carbon that constitute them. Important directive rules have been approved over the years, but further research and regulatory measures should be introduced for a safer production and utilization of CNTs. Against this background, and after an overview of CNMs and CNTs, the antimicrobial properties of pristine and modified SWNTs and MWCNTs as well as the most relevant in vitro and in vivo studies on their possible toxicity, have been reported. Strategies and preventive behaviour to limit CNT risks have been provided. Finally, a debate on regulatory issues has also been included. Full article

An uncooled microbolometer is a thermal sensor consisting of a membrane suspended from the substrate to provide thermal insulation. Typically, the membrane is composed of a stack of three films integrated by a supporting film, an IR sensing film, and an IR absorbing film. However, the above increases the thickness of the device and affects its mechanical stability and thermal mass, thereby reducing its performance. One solution is to use a single film as a membrane with both IR sensing and IR absorbing properties. In this regard, this work presents the fabrication and evaluation of uncooled microbolometers using nitrogen-doped hydrogenated amorphous silicon-germanium (a-SiGe:H,N) as a single IR-absorber/IR sensing membrane. The films were deposited via low frequency Plasma Enhanced Chemical Vapor Deposition (PECVD) at 200 °C. Three microbolometer configurations were fabricated using a-SiGe:H,N films deposited from a SiH₄, GeH₄, N_2, and H₂ gas mixture with different SiH₄ and GeH₄ flow rates and, consequently, with different properties, such as temperature coefficient of resistance (TCR) and conductivity at room temperature. The microbolometer that exhibited the best performance achieved a voltage responsivity of 7.26 × 10⁵ V/W and a NETD of 22.35 mK at 140 Hz, which is comparable to state-of-the-art uncooled infrared (IR) sensors. These results confirm that the optimization of the deposition parameters of the a-SiGe:H,N films significantly affects the microbolometers final performance, enabling an optimal balance between thermal sensitivity (TCR) and conductivity. Full article

In this paper, we present recent advancements in transmitter and receiver technologies for Optical Wireless Communication (OWC). OWC offers very wide license-free optical spectrum which enables very high capacity transmission. Additionally, beam-steered OWC is more power-efficient and more secure due to low divergence of light. One of the main challenges of OWC is wide angle transmission and reception because law of conservation of etendue restricts maximization of both aperture and field of view (FoV). On the transmitter side, we use Micro Electro-Mechanical System cantilevers activated by piezoelectric actuators together with silicon micro-lenses for narrow laser beam steering. Such design allowed us to experimentally demonstrate at least 10 Gbps transmission over 100° full angle FoV. On the receiver side, we show the use of photodiode array, and Indium-Phosphide Membrane on Silicon (IMOS) Photonic Integrated Circuit (PIC) with surface grating coupler (SGC) and array of SGC. We demonstrate FoV greater than 32° and 16 Gbps reception with photodiode array. PIC receiver allowed to receive 100 Gbps WDM with single SGC, and 10 Gbps with an array of SGC which had 8° FoV in the vertical angle and full FoV in the horizontal angle. Our results suggest that solutions presented here are scalable in throughputs and can be adopted for future indoor high-capacity OWC systems. Full article

This study focused on synthesizing polyvinyl alcohol (PVA) utilizing glutaraldehyde (GA) as a crosslinking agent and silicon dioxide (SiO₂) nanopowder with titanium dioxide (TiO₂) nanopowder to reduce or prevent the hydrophilic property of PVA. Integrating SiO₂ and TiO₂ into the PVA boosted the hydrophobicity, thermal properties, and self-cleaning of the PVA film. The characteristic properties of PVA/GA, PVA/SiO₂/GA, and PVA/SiO₂/TiO₂/GA nanocomposites polymer membranes were investigated by gel content, swelling capacity, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction patterns (XRD), scanning electron microscope (SEM), thermal gravimetric analysis (TGA), and contact angle. The resulting PVA/5%SiO2/1%TiO₂/GA nanocomposite exhibits much better physical properties than PVA/GA hydrogel (water absorbency from 3.1 g/g to 0.07 g/g and contact angel from 0° to 125°). In addition, the nanocomposite retains very low swelling properties. These prepared nanocomposites are promising in a variety of applications such as sand soil stabilizers, construction, and building works where they exhibit excellent water resistance performance. This study introduces a novel approach for creating hydrophobic polymeric membranes from hydrophilic polymeric materials to stabilize sandy soil effectively. Full article

A platform for converting near-infrared (NIR) laser power modulation into the self-mixing (SM) signal of a quantum cascade laser (QCL) operating at terahertz (THz) frequencies is introduced. This approach is based on laser feedback interferometry (LFI) with a THz QCL using a metal-coated silicon nitride trampoline membrane resonator as both the external QCL laser cavity and the mechanical coupling element of the two-laser hybrid system. We show that the membrane response can be controlled with high precision and stability both in its dynamic (i.e., piezo-electrically actuated) and static state via photothermally induced NIR laser excitation. The responsivity to nanometric external cavity variations and robustness to optical feedback of the QCL LFI apparatus allows a highly sensitive and reliable transfer of the NIR power modulation into the QCL SM voltage, with a bandwidth limited by the thermal response time of the membrane resonator. Interestingly, a dual information conversion is possible thanks to the accurate thermal tuning of the membrane resonance frequency shift and displacement. Overall, the proposed apparatus can be exploited for the precise opto-mechanical control of QCL operation with advanced applications in LFI imaging and spectroscopy and in coherent optical communication. Full article