Search Results (71)

Solid Oxide Fuel Cells (SOFCs) offer high-efficiency electrochemical conversion of fuels like natural gas, yet detailed modeling is crucial for optimization. This paper presents a simulation study of a natural gas-fueled SOFC system, developed using Aspen Plus with Fortran integration. Distinct from prevalent paradigms assuming rated power output, this work adopts rated current density as the primary input, enabling a more direct investigation of the cell’s electrochemical behavior. We conducted a comprehensive sensitivity analysis of key parameters, including fuel utilization, water-carbon ratio, and current density, and further investigated the impact of different interconnection configurations on overall module performance. Results demonstrate that a single unit operating at a current density of 180 mA/cm², a fuel utilization of 0.75, and a water-carbon ratio of 1.5 can achieve a maximum net stack-level electrical efficiency of 54%. Furthermore, optimizing the interconnection of a 400 kW module by combining series and parallel units boosts the overall net system-level electrical efficiency to 59%, a 5-percentage-point increase over traditional parallel setups. This is achieved by utilizing a bottoming cycle for exhaust heat recovery. This research validates the rated current density approach for SOFC modeling, offering novel insights into performance optimization and modular design for integrated energy systems. Full article

Hybrid thermoelectric generators (HTEGs) play a pivotal role in sustainable energy conversion by harnessing waste heat through the Seebeck effect, contributing to global efforts in energy efficiency and environmental sustainability. In practical sustainable energy systems, HTEG output performance is significantly influenced by uncertainties in the operational parameters (such as temperature differences and load resistance), material properties (including Seebeck coefficient and resistance), and structural configurations (like the number of series/parallel thermoelectric components), which impact both efficiency and system stability. This study employs the Sobol-sequence-sampling method to characterize these parameter uncertainties, analyzing their effects on HTEG output power and conversion efficiency using mean values and standard deviations as evaluation metrics. The results show that higher temperature differences enhance output performance but reduce stability, a larger load resistance decreases performance while improving stability, thermoelectric materials with high Seebeck coefficients and low resistance boost efficiency at the expense of stability, increasing series-connected components elevates performance but reduces stability, parallel configurations enhance power output yet decrease efficiency and stability, and greater contact thermal resistances diminish performance while enhancing system robustness. This research provides theoretical guidance for optimizing HTEGs in sustainable energy applications, enabling the development of more reliable, efficient, and eco-friendly thermoelectric systems that balance performance with environmental resilience for long-term sustainable operation. Full article

Ensuring a sustainable and healthy human environment in university dormitories is essential for students’ learning, living, and overall health and well-being. To address this need, we carried out a series of systematic field measurements of the noise levels at 30 dormitories in three representative major urban universities in a major provincial capital city in China and designed and implemented a comprehensive questionnaire and surveyed 1005 students about their perceptions of their acoustic environment. We proposed and applied a sustainability–health-oriented, multidimensional assessment framework to assess the acoustic environment of the dormitories and student responses to natural sound, technological sounds, and human-made sounds. Using the Structural Equation Modeling (SEM) approach combined with the field measurements and student surveys, we identified three categories and six factors on student health and well-being for assessing the acoustic environment of university dormitories. The field data indicated that noise levels at most of the measurement points exceeded the recommended or regulatory thresholds. Higher noise impacts were observed in early mornings and evenings, primarily due to traffic noise and indoor activities. Natural sounds (e.g., wind, birdsong, water flow) were highly valued by students for their positive effect on the students’ pleasantness and satisfaction. Conversely, human and technological sounds (traffic noise, construction noise, and indoor noise from student activities) were deemed highly disturbing. Gender differences were evident in the assessment of the acoustic environment, with male students generally reporting higher levels of the pleasantness and preference for natural sounds compared to female students. Educational backgrounds showed no significant influence on sound perceptions. The findings highlight the need for providing actionable guidelines for dormitory ecological design, such as integrating vertical greening in dormitory design, water features, and biodiversity planting to introduce natural soundscapes, in parallel with developing campus activity standards and lifestyle during noise-sensitive periods. The multidimensional assessment framework will drive a sustainable human–ecology–sound symbiosis in university dormitories, and the category and factor scales to be employed and actions to improve the level of student health and well-being, thus, providing a reference for both research and practice for sustainable cities and communities. Full article

The presence of toxic gas emissions from conventional vehicles is worrisome globally. Over the past few years, there has been a broad adoption of electric vehicles (EVs) to reduce energy usage and mitigate environmental emissions. The EVs are characterized by limited range, cost, and short range. This prompts the need for hybrid electric vehicles (HEVs). This study describes the conversion of a 2022 Volkswagen Crafter (VW) 35 TDI 340 delivery van from a conventional diesel powertrain into a hybrid electric vehicle (HEV) augmented with synchronous electrical machines (motor and generator) and a BMW i3 60 Ah battery pack. A downsized 1.5 L diesel engine and an electric motor–generator unit are integrated via a planetary power split device supported by a high-voltage lithium-ion battery. A MATLAB (R2024b) Simulink model of the hybrid system is developed, and its speed tracking PID controller is optimized using genetic algorithm (GA) and particle swarm optimization (PSO) methods. The simulation results show significant efficiency gains: for example, average fuel consumption falls from 9.952 to 7.014 L/100 km (a 29.5% saving) and CO₂ emissions drop from 260.8 to 186.0 g/km (a 74.8 g reduction), while the vehicle range on a 75 L tank grows by ~40.7% (from 785.7 to 1105.5 km). The optimized series–parallel powertrain design significantly improves urban driving economy and reduces emissions without compromising performance. Full article

A Lipophilic Prodrug Charge Masking (LPCM) strategy involves masking of hydrophilic peptide charges with alkoxycarbonyl groups, which are cleaved by esterases after intestinal absorption. This study investigates the LPCM strategy’s applicability to oxytocin (OT), a peptide with well-defined biological activity. A series of OT prodrugs with varying alkoxycarbonyl chain lengths (2 to 12 carbon atoms) were synthesized, and their permeability was assessed using parallel artificial membrane permeability assay (PAMPA) and Caco-2 cell culture models. The PAMPA results indicated that OT demonstrated poor permeability (P_app = 2.2 × 10⁻⁶ cm/s), while its prodrugs Hoc-OT, Oct-OT, and Dec-OT were characterized by significantly better permeability, with Dec-OT achieving a four-fold increase over OT. The prodrug with a 12-carbon chain (Dod-OT) exhibited poor permeability; however, its high mass retention suggests strong membrane affinity. Further evaluation, using the Caco-2 cell model, revealed a 1.8-fold higher P_app of Oct-OT compared to OT, indicating possible higher oral availability. Conversely, Hoc-OT exhibited lower permeability than OT. Our findings indicate that the LPCM strategy can effectively boost the oral bioavailability of certain peptides, paving the way for their transformation into bioavailable drugs. Full article

While vibration harvesting shows promise for powering sensors, effectively harvesting low-frequency, multidirectional ambient vibrations remains challenging. This article presents a novel electromagnetic vibration energy harvesting device (EVEHD) with three key innovations: a dual-mode mass-pendulum configuration—dual-mass coupling (series mode) amplifies induced voltage, and dual-mass uncoupled (parallel) mode enables multifrequency harvesting—spring-position-based frequency tuning (4.5–16.7 Hz in series mode; dual-band 3.7–9.3/5–13.3 Hz in parallel mode), and an optimized energy conversion structure, boosting output by 85.2%. The findings were validated through theoretical modeling, FEM simulations, and shaker tests, the EVEHD generating a maximum voltage of 2 V and a power of 769.2 mW under a base excitation amplitude of 0.5 g at 16.7 Hz. This work reveals the potential of this multidirectional EVEHD for power generation and application in self-powered systems. Full article

An epoxy/glass microbeads-based 1-3 piezoelectric composite is proposed, to enhance electromechanical conversion efficiency. Firstly, based on the series-parallel theory, the theoretical model is established. Secondly, the epoxy resin/glass microbeads-based 1-3 piezoelectric composite is simulated by finite element software. The effects of polymers with different acoustic impedances, the thicknesses of piezoelectric composites, and ceramic volume fractions are analyzed systematically. After parameter optimization, the epoxy/glass microbeads-based 1-3 piezoelectric composite is prepared. The experimental results agree well with the theoretical and simulation results. When the ceramic volume fraction is 60.0%, its electromechanical coupling factor is the largest, which is 0.714. Compared with the prepared traditional 1-3 piezoelectric composites with the same parameters, its electromechanical coupling factor is increased by 7.8%. Therefore, the epoxy/glass microbeads-based 1-3 piezoelectric composite can enhance the sensitivity and resolution of the transducers, which has potential advantages for improving the performance of transducers. Full article

The present study examines the relationship between thermal and configurational entropy in two resistors in parallel and in series. The objective is to introduce entropy in electric circuit analysis by considering the impact of system geometry on energy conversion in the circuit. Thermal entropy is derived from thermodynamics, whereas configurational entropy is derived from network modelling. It is observed that the relationship between thermal entropy and configurational entropy varies depending on the configuration of the resistors. In parallel resistors, thermal entropy decreases with configurational entropy, while in series resistors, the opposite is true. The implications of the maximum power transfer theorem and constructal law are discussed. The entropy generation for resistors at different temperatures was evaluated, and it was found that the consideration of resistor configurational entropy change was necessary for consistency. Furthermore, for the sake of generalization, a similar behaviour was observed in time-dependent circuits, either for resistor–capacitor circuits or circuits involving degradation. Full article

Battery storage systems are becoming very popular around the world. However, they are mainly used in industry for high-performance applications. Domestic use is still sporadic due to size and cost issues. This work overviews basic conceptual designs for a cost-effective battery storage system. The main specificity of the proposed systems is the use of commonly available recycled batteries from household appliances such as laptops and backup power supplies. The circuit topology considered is a 3S (three cells in series) configuration. This is because such wiring arrangements are those that are most often found in the home appliances described here. The technical solutions of the device itself focus on the ratio of the efficiency of the whole system to the production cost. Given the above, attention was paid to the simulation analysis of the operating modes, which directly influenced the components’ price. Changing the switching control scheme of the power transistors makes it possible to reduce the requirements for the driving components used with minimal impact on the power conversion efficiency (Δη 1–4%). According to the established findings, a prototype was made on which the simulation findings were verified; then, we further focused on the experimental measurement of the efficiency of the MPPT converter and conducted an analysis of a methodology in which we measure the deviation from the actual point of maximum power. The simple possibility of parallelizing the individual storage devices will again help improve the system’s overall efficiency. This makes the system suitable for use in small spaces such as houses, garages, cellars, etc. Full article

The mitigating effects of straw burning bans on air pollution are widely known; however, their effects on indoor air pollution are generally ignored. Cooking fuel use is an important factor that affects indoor air quality. However, the debate over the pros and cons of a province-wide ban on straw burning has been a major issue in environmental economics. By utilizing household survey data, this study investigates the role of straw burning bans on cooking fuel use in households. To infer causal relationships, difference-in-difference models that compare households in provinces with and without a complete ban on open straw burning (COSB) are employed. The results show that COSBs promote the use of clean cooking fuels and discourage the use of firewood for cooking by households. These results hold true after a series of robustness tests, such as parallel trends and placebo tests. However, the results show that the effect of COSBs on the household use of coal as a cooking fuel is not significant. Further analysis shows heterogeneity in the effects of COSBs on the use of household cooking fuels. Thus, COSBs promote the conversion to cleaner cooking fuels in rural households, but the implementation of these policies needs to be contextualized. Full article

Tick eggs contain a series of proteins that play important roles in egg development. A thorough characterization of egg protein expression throughout development is essential for understanding tick embryogenesis and for screening candidate molecules to develop novel interventions. In this study, eggs at four developmental stages (0, 7, 14, and 21 incubation days) were collected, and their protein extraction was profiled using sodium dodecyl sulfate–polyacrylamide gel electrophoresis (SDS-PAGE). On the first day of egg protein extraction, protein bands from day-1 eggs were re-collected and subsequently analyzed using liquid chromatography–tandem mass spectrometry (LC-MS/MS). The dynamic changes in forty egg proteins during development were further investigated using LC-parallel reaction monitoring (PRM)/MS analysis. A total of 108 transcripts were detected in day-1 eggs. Based on protein functions and families, these transcripts were classified into eight categories: transporters, enzymes, immunity and antimicrobial proteins, proteinase inhibitors, cytoskeletal proteins, heat shock proteins, secreted proteins, and uncharacterized proteins. Identification of the protein bands revealed that nine bands predominantly consisted of vitellogenin and vitellin-A, while other notable proteins included cathepsins and Kunitz domain-containing proteins. LC-PRM/MS analysis indicated that 28 transcripts increased significantly in abundance, including 13/18 enzymes, 1/1 antimicrobial peptide, 2/2 neutrophil elastase inhibitors, 3/4 vitellogenins, 3/3 heat shock proteins, 3/3 cytoskeletal proteins, 1/1 elongation factor-1, and 1/1 uncharacterized protein. Conversely, five transcripts showed a decrease significantly, including 1/1 Kunitz domain-containing protein, 2/6 aspartic proteases, and 2/5 serpins. This research provides a comprehensive overview of egg proteins and highlights the dynamic changes in protein expression during embryonic development, which may be pivotal for understanding protein functions and selecting potential candidates for further study. Full article

In electric powertrain traction applications, the adopted trend to improve the performance and efficiency of electromechanical power conversion systems is to increase supply voltages and inverter switching frequencies. As a result, electrical machine conductors are subjected to ever-increasing electrical stresses, leading to premature insulation degradation and eventual short-circuits. Winding condition monitoring is crucial to prevent such critical failures. Based on the scientific literature, several methods can be used for early identification of aging. A first solution is to monitor partial discharges. This method requires the use of a specific measurement device and an undisturbed test environment. A second solution is to monitor the inter-turn winding capacitance, which is directly related to the condition of the insulation and can cause a change in the stator impedance behavior. Several approaches can be used to estimate or characterize this impedance behavior. They must be performed on a machine at standstill, which limits their application. In this paper, a new characterization method is proposed to monitor the high-frequency stator impedance evolution of voltage source inverter-fed machines. This method can be applied at any time without removing the machine from its operating environment. The range and accuracy of the proposed frequency characterization depend in particular on the supply voltage level and the bandwidth of the measurement probes. The effects of parameters such as temperature, switching frequency, and DC voltage amplitude on the impedance characteristic were also studied and will be presented. Tests carried out on an automotive traction machine have shown that the first two series and parallel resonances of the high-frequency impedance can be accurately identified using the proposed technique. Therefore, by monitoring these resonances, it is possible to predict the aging rate of the conductor. Full article

In this paper, a novel topology and method for designing a multi-band rectenna is proposed to improve its RF-DC efficiency. The rectifier achieves simultaneous rectification using both series and parallel configurations by connecting two branches to the respective terminals of the diode, directing the energy input from two ports to the anode and cathode of the diode. Six desired operating frequency bands are evenly distributed across these two branches, each of which is connected to antennas corresponding to their specific operating frequencies, serving as the receiving end of the system. To optimize the design process, a low-pass filter is incorporated into the rectifier design. This filter works in conjunction with a matching network that includes filtering capabilities to isolate the two ports of the rectifier. The addition of the filter ensures that each structure within the rectifier can be designed independently without adversely affecting the performance of the already completed structures. Based on the proposed design methodology, a dual-port rectenna operating at six frequency bands—1.85 GHz, 2.25 GHz, 2.6 GHz, 3.52 GHz, 5.01 GHz, and 5.89 GHz—was designed, covering the 4G, 5G, and Wi-Fi/WLAN frequency bands. The measured results indicate that high-power conversion efficiency was achieved at an input power of −10 dBm: 43.01% @ 1.85 GHz, 41.00% @ 2.25 GHz, 41.33% @ 2.6 GHz, 35.88% @ 3.52 GHz, 22.36% @ 5.01 GHz, and 19.27% @ 5.89 GHz. When the input power is −20 dBm, the conversion efficiency of the rectenna can be improved from 5.2% for single-tone input to 27.7% for six-tone input, representing a 22.5 percentage point improvement. The proposed rectenna demonstrates significant potential for applications in powering low-power sensors and other devices within the Internet of Everything context. Full article

Theoretical and experimental work for a novel topology of DC-DC boost switching capacitor converter is introduced in this paper. This new design is an adjustment for boost series and parallel topology developed by Makowski. Thus, a comparison between the two designs presented in this paper aims to highlight the improvement in the conversion rate of the boost converter’s output voltage while using the same number and size of capacitors. Converter analyses for both with and without load are presented. Also, a boost converter with a nonlinear ferroelectric capacitor is presented to further increase the boost converter conversion rate using advantages of the ferroelectric capacitors, such as their big dielectric constant and polarization reversal. Full article

This article presents a power-efficient DC-DC converter based on a switched-capacitor (SC) cell in power management systems supplied for fully integrated photovoltaic (PV) modules. These modules shall provide high-performance point-of-load voltage regulation. The primary objective of this study is to better utilize capacitance and switches by selecting a proper SC topology in order to improve the power efficiency of SC converters. A general steady-state performance model is investigated to optimize and compare a variety of SC DC-DC topologies. The investigation method relies on a charge-multiplier approach and considers the impact of area constraint on capacitors. To identify the most suitable topology for a given conversion ratio, the performance-limit metrics of SC converters are calculated. The analysis provides framework to determine optimum switch size and switching frequency for a two-phase 3:1 series–parallel converter for a target load current of 10 mA implemented on a 22 nm process technology. The results shows that a minimum of 250 MHz switching frequency is desirable for achieving a target efficiency greater than 85% while maintaining the minimum output voltage of 0.34 V. The analysis results are verified through MATLAB and PSpice-based simulations. Full article