Search Results (138)

A study was conducted on the construction of sulfonated poly(aryl ether ketone) nanomicelles and their dispersion–displacement synergistic behavior in deep oil recovery. Unlike conventional surfactant systems, inorganic nanoparticle-based EOR materials, and polymeric nanofluids that mainly rely on interfacial tension reduction, wettability alteration, or viscosity regulation, this study constructs self-assembled sulfonated poly(aryl ether ketone) nanomicelles that integrate a rigid aromatic backbone, ionizable sulfonic acid groups, nanoscale dispersion, and interfacial regulation within one polymeric architecture. Sulfonated poly(aryl ether ketone) nanomicelles were prepared by combining polymer sulfonation with solvent-induced self-assembly, and their structural features, dispersion stability, interfacial behavior, porous-media transport, and displacement performance were systematically evaluated. Spectroscopic characterization confirmed the successful introduction of sulfonic acid groups into the polymer backbone. The resulting nanomicelles exhibited an average hydrodynamic diameter of 117.8 nm, a polydispersity index of 0.186, and a zeta potential of −38.6 mV in deionized water, while a value of −27.4 mV was still maintained at a salinity of 150,000 mg/L, indicating good electrostatic stability under highly mineralized conditions. Further evaluation showed that the 0.30 wt% system retained a transmittance of 97.4% after 15 d of static standing, and its particle size remained at 151.7 nm even under 120 °C and 150,000 mg/L, demonstrating favorable thermal–salinity tolerance. At the same concentration, the oil–water interfacial tension decreased to 6.9 mN/m at 1800 s, while the contact angle of oil-aged quartz was reduced from 118.4° to 58.7°, indicating effective regulation of both the oil–water interface and the solid surface wettability. During microscopic displacement, the residual oil area fraction decreased from 32.8% after water flooding to 14.6%, and cluster-like oil, corner oil, and film-like oil were reduced from 14.6%, 9.8%, and 8.4% to 5.9%, 4.2%, and 4.5%, respectively. In core flooding, the incremental oil recovery reached 13.2%, the final water cut decreased to 81.2%, and the injection pressure increased only from 0.42 MPa to 0.68 MPa. These results indicate that sulfonated poly(aryl ether ketone) nanomicelles promote deep residual-oil mobilization through the combined effects of stable dispersion, interfacial regulation, and effective transport, with 0.30 wt% identified as the preferred concentration range. The main scientific contribution of this work is to establish a structure–dispersion–interface–transport–displacement relationship for SPAEK nanomicelles under deep-reservoir conditions, providing a polymeric nanomicelle-based strategy distinct from conventional surfactant, sulfonated polymer, and nanoparticle flooding systems. Full article

Cutaneous wound healing is a complex biological process often impaired by bacterial infections, especially by Staphylococcus aureus. To address this, alginate (ALG)/chitosan (CS) polyelectrolyte multilayer (PEM) films incorporating alginate-coated silver nanoparticles (ALG–AgNPs) were fabricated by layer-by-layer self-assembly. The films exhibited a porous, layered morphology with homogeneous distribution of ALG–AgNPs, hydrophilic surfaces (contact angle ≈ 55°), a high swelling degree (~175%), and a water vapor transmission rate of 1830 g m⁻²·day⁻¹. Thermal analyses showed similar degradation profiles up to 600 °C, with the ALG–AgNP film displaying lower moisture loss and higher dehydration temperature, consistent with enhanced ionic and coordination crosslinking (–NH₃⁺/–COO⁻ and Ag–O–C bonds). The release of Ag⁺ in PBS (pH 7.4) was ~3% after 24 h, following a Korsmeyer–Peppas mechanism (R² = 0.97, n < 0.5), and degradation, with ~40% mass loss in 6 days, indicated gradual matrix disintegration. Cytocompatibility studies revealed >80% viability for fibroblasts, keratinocytes, macrophages, and <2% hemolysis of red blood cells. Immune assays showed a tendency towards reduced TNF-α and IL-1β and regulated IL-6/IL-8 release. Antibacterial evaluations demonstrated a 5-log reduction in planktonic bacterial viability and >2-log reduction in adhesion, and an 11 ± 1 mm inhibition zone for S. aureus. These results demonstrate that ALG/CS–AgNP PEM films combine biocompatibility, antibacterial efficacy, controlled degradation, and structural stability, making them promising multifunctional scaffolds for the regeneration of infected skin wounds. Full article

Magnetic-field-assisted electrocatalysis offers a powerful route to enhance the oxygen evolution reaction (OER) by coupling spin-dependent effects with magnetohydrodynamic phenomena. Here, we present a unified study of cobalt ferrite (CoFe₂O₄)-based nanofilms, elucidating the combined roles of rare-earth doping, nanoparticle size, film morphology, and electrode substrate magnetism on OER performance under external magnetic fields. The effect of UV-light irradiation is also investigated. CoFe₂O₄ and yttrium-doped CoFe₂O₄ nanoparticles were synthesized via thermal decomposition and self-combustion routes, yielding single-domain particles with distinct structural and magnetic properties, and assembled into homogeneous nanofilms using the Langmuir–Blodgett technique. Electrocatalytic measurements in alkaline media reveal that intrinsic OER activity is primarily governed by film compactness and charge-transfer efficiency, while the magnitude of magnetic-field-induced enhancement depends on the magnetic response of both the nanofilms and the supporting electrode. Ferromagnetic substrates promote enhanced catalytic activity under magnetic fields, whereas diamagnetic substrates can exhibit suppressed performance. Across all systems, the strongest enhancement is observed when the magnetic field is applied parallel to the electrode surface, reflecting the combined effects of spin polarization and Lorentz-force-driven mass transport. UV-light irradiation is also evaluated as an external stimulus to promote the reaction. Our findings establish a comprehensive framework for designing magnetically assisted OER electrocatalysts and demonstrate that magnetic-field effects can rival or complement rare-earth doping or UV-light irradiation, offering a sustainable pathway toward high-efficiency water oxidation. Full article

This work reports an enhanced flexible vacuum-ultraviolet (VUV) photodetector on a polyimide (PI) substrate based on hexagonal boron nitride nanosheets (BNNSs) with Al nanoparticles (Al NPs). The BNNS film were prepared via liquid-phase exfoliation combined with a self-assembly process, and size-controllable Al NPs were constructed on the BNNS’s surface by electron-beam evaporation followed by thermal annealing. When the Al film thickness was 15 nm, the annealed Al NPs exhibited a pronounced enhancement of photoelectric effects at a wavelength of 185 nm. Combined with finite-difference time-domain (FDTD) simulations, it was confirmed that the localized surface plasmon resonance (LSPR) generated by Al NPs significantly enhanced the local electromagnetic field and effectively coupled into the interior of BNNSs. These exhibited a strong plasmon-enhanced absorption effect and thereby improved light absorption and carrier generation efficiency. The flexible photodetector based on this structure showed an increase in the photo-to-dark current ratio from 110.17 to 527.79 under a bias voltage of 20 V, while maintaining fast response and recovery times of 79.79 ms and 82.38 ms, respectively. In addition, the device demonstrated good stability under multiple bending angles and cyclic bending conditions, highlighting its potential applications in flexible solar-blind VUV photo ultraviolet. Full article

This study investigates the dynamic magneto-optical properties of ferrofluid thin films, focusing on how magnetic fields induce light–matter interactions using a device known as Ferrocell. Our findings reveal that incident light interacts with self-assembled, anisotropic nanoparticle structures, transforming the ferrofluid into a highly responsive optical medium. Monochromatic laser experiments confirmed the direct correlation between laser color and diffracted light color offering direct insights into particle orientation and aggregate morphology. We observed significant chromatic shifts, especially in regions under strong perpendicular magnetic fields, which provide compelling evidence of structural colors. This phenomenon stems from wavelength-selective interference and diffraction, reminiscent of photonic crystal behavior, yet characterized by short-range order, classifying the material as a photonic glass. Full article

Traditional nanoparticle aerogels suffer from inherent brittleness and thermal instability at elevated temperatures. In recent years, ceramic nanofiber aerogels, utilizing flexible nanofibers as structural units, have emerged as mechanically resilient alternatives with ultrahigh porosity (>90%). However, their thermal insulation capabilities are compromised by micron-scale pores (10–100 μm) and overdependence on ultralow density, which exacerbates mechanical fragility. This study pioneers a gas-phase self-assembly strategy to fabricate Si₃N₄ nanoparticle reinforced Si₃N₄ nanofiber aerogels (SNP-R-SNFA) with gradient pore architectures. By leveraging methyltrimethoxysilane/vinyltriethoxysilane composite aerogel (MVa) as a reactive template, we achieved spontaneous growth of Si₃N₄ nanofiber films (SNP-R-SNF) featuring nanoparticle-fiber interpenetration and porosity gradients. The microstructure formation mechanism of SNP-R-SNF was analyzed using field-emission scanning electron microscopy. Layer assembly and hot-pressing composite technology were employed to prepare the SNP-R-SNFA, which showed low density (0.033 g/cm³), exceptional compression resilience, insensitive frequency dependence of dielectric properties (ε′ = 2.31–2.39, tan δ < 0.08 across 8–18 GHz). Infrared imaging displayed backside 893 °C cooler than front, demonstrating superior insulation performance. This study not only provides material solutions for integrated electromagnetic wave-transparent/thermal insulation applications but more importantly establishes an innovative paradigm for enhancing the mechanical robustness of nanofiber-based aerogels. Full article

Flexible polymer-based piezoelectric nanogenerators (PENGs) have gained significant interest due to their ability to deliver clean and sustainable energy for self-powered electronics and wearable devices. Recently, the incorporation of fillers into the ferroelectric polymer matrix has been used to improve the relatively low piezoelectric properties of polymer-based PENGs. In this study, we investigated the effect of various nanofillers such as titania (TiO₂), zinc oxide (ZnO), reduced graphene oxide (rGO), and lead zirconate titanate (PZT) on the PENG performance of the nanocomposite thin films containing the nanofillers in poly(vinylidene fluoride-co-trifluoro ethylene) (P(VDF-TrFE)) matrix. The nanocomposite films were prepared by depositing molecularly thin films of P(VDF-TrFE) and nanofiller nanoparticles (NPs) spread at the air/water interface onto the indium tin oxide-coated polyethylene terephthalate (ITO-PET) substrate, and they were characterized by measuring their microstructures, crystallinity, β-phase contents, and piezoelectric coefficients (d₃₃) using SEM, FT-IR, XRD, and quasi-static meter, respectively. Multiple PENGs incorporating various nanofillers within the polymer matrix were developed by assembling thin film-coated substrates into a sandwich-like structure. Their piezoelectric properties, such as open-circuit output voltage (V_OC) and short-circuit current (I_SC), were analyzed. As a result, the PENG containing 4 wt% PZT, which was named P-PZT-4, showed the best performance of V_OC of 68.5 V with the d₃₃ value of 78.2 pC/N and β-phase content of 97%. The order of the maximum V_OC values for the PENGs of nanocomposite thin films containing various nanofillers was PZT (68.5 V) > rGO (64.0 V) > ZnO (50.9 V) > TiO₂ (48.1 V). When the best optimum PENG was integrated into a simple circuit comprising rectifiers and a capacitor, it demonstrated an excellent two-dimensional power density of 20.6 μW/cm² and an energy storage capacity of 531.4 μJ within 3 min. This piezoelectric performance of PENG with the optimized nanofiller type and content was found to be superior when it was compared with those in the literature. This PENG comprising nanocomposite thin film with optimized nanofiller type and content shows a potential application for a power source for low-powered electronics such as wearable devices. Full article

High-sensitivity and repeatable detection of hydrophobic molecules through the surface-enhanced Raman scattering (SERS) technique is a tough challenge because of their weak adsorption and non-uniform distribution on SERS substrates. In this research, we present a simple self-assembly protocol for monolayer SERS mediated by 6-deoxy-6-thio-β-cyclodextrin (β-CD-SH). This protocol allows for the rapid assembly of a compact silver nanoparticle (Ag NP) monolayer at the oil/water interface within 40 s, while entrapping analyte molecules within hotspots. The proposed method shows general applicability for detecting hydrophobic molecules, exemplified as Nile blue, Nile red, fluconazole, carbendazim, benz[a]anthracene, and bisphenol A. The detection limits range from 10⁻⁶to 10⁻⁹ M, and the relative standard deviations (RSDs) of signal intensity are less than 10%. Moreover, this method was used to investigate the release behaviors of a hydrophobic pollutant (Nile blue) adsorbed on the nanoplastic surface in the water environment. The results suggest that elevated temperatures, increased salinities, and the coexistence of fulvic acid promote the release of Nile blue. This simple and fast protocol overcomes the difficulties related to hotspot accessibility and detection repeatability for hydrophobic analytes, holding out extensive application prospects in environmental monitoring and chemical analysis. Full article

Grazing incidence small- and wide-angle X-ray scattering (GISAXS, GIWAXS) has been widely applied for the study of functional thin films, be it for the characterization of nanostructured morphologies in block copolymers, nanocomposites, and nanoparticle assemblies, or for the packing and orientation of aromatic molecules or conjugated polymers. Solution-processed thin films are typically uniaxial powders, with a specific crystallographic plane oriented parallel to the substrate surface while ordered domains assume random orientations laterally. The convenient GISAXS/GIWAXS scattering geometry facilitates obtaining complete information about thin film structure as well as the ability to study samples in well-defined sample environments, as controlled by temperature, exposure to solvent vapor and drying, or coating processes. Moreover, with suitable X-ray sources and detectors, information about the ordering kinetics and phase transitions can be obtained down to the millisecond scale. The scattering geometry and an interactive graphical tool to index such scattering patterns will be discussed here. Furthermore, it will be demonstrated that proper indexing of the X-ray scattering patterns can provide deep insight into thin film structure–property relationships and the kinetics of structure formation. Recent examples of nanostructures and molecular organization in thin films will be discussed, as well as self-assembly processes leading to such structures. Full article

Nanocellulose has prompted extensive exploration of its applications in advanced functional materials, especially humidity-responsive materials. However, the sunflower pith (SP), a unique agricultural by-product with high cellulose and pectin content, is always ignored and wasted. This work applied sulfuric acid hydrolysis and sonication to sunflower pith to obtain nanocellulose and construct film materials with humidity-responsive properties. The SP nanoparticle (SP-NP) suspension could form a transparent film with stacked layers of laminated structure. Due to the tightly layered structure and expansion confinement effect, when humidity increases, the SP-NP film responds rapidly in just 0.5 s and completes a full flipping cycle in 4 s, demonstrating its excellent humidity-responsive capability. After removing hemicellulose and lignin, the SP cellulose nanocrystals (SPC-NC) could self-assemble into a chiral nematic structure in the film, displaying various structural colors based on different sonication times. The color of the SPC-NC film dynamically adjusted with changes in ambient humidity, exhibiting both functionality and aesthetics. This research provides a new perspective on the high-value utilization of sunflower pith while establishing a practical foundation for developing novel responsive cellulose-based materials. Full article

Background: The properties of nanoparticle surfaces are crucial in influencing their interaction with biological environments, as well as their stability, biocompatibility, targeting abilities, and cellular uptake. Hydrophobin 4 (HFB4) is a class II HFB protein produced by filamentous fungi that has a natural ability to self-assemble at hydrophobic-hydrophilic interfaces. The biocompatible, non-toxic, biodegradable, and amphipathic properties of HFB4 render it valuable for improving the solubility and bioavailability of hydrophobic drugs. We have investigated the physicochemical properties, cellular uptake, and anticancer effects of empty and Doxorubicin (Dox)-loaded HFB4 liposomes (HFB4L) and compared them to those of PEGylated liposomes (PPL). Methods: The Pichia pastoris KM71H strain was used for HFB4 purification. Liposomes were prepared through the thin film hydration method and characterized. The cytotoxic effects of free Dox, Dox-HFB4, and Dox-PPL were assessed in MCF7 cells using the SRB Assay. Results: All formulations showed good size homogeneity and a spherical shape. The HFB4 coating enhanced the physicochemical stability of Dox-HFB4L over 60 days at 4 °C without significantly affecting Dox release from HFB4L. It increased Dox release at pH 5.4 compared to pH 7.4, indicating higher delivery of drugs into acidic tumor environments, similar to Dox-PPL. While both formulations showed increased cellular uptake compared to free Dox, they exhibited a lower anticancer effect due to the sustained release of Dox. Notably, Dox-HFB4L displayed greater cytotoxicity than Dox-PPL in MCF7 cells. Conclusions: HFB4L may offer superior benefits in terms of delivering drugs to an acidic tumor environment in a stable, non-toxic, and sustained manner. Full article

Both nanoscience and nanotechnology have undoubtedly contributed significantly to the development of thermite-based nanoenergetic materials (NEMs) with tunable and tailorable combustion performance and their subsequent integration into devices. Specifically, this review article reflects the immense paybacks in designing and fabricating ordered/disordered assembly of energetic materials over multiple length scales (from nano- to milli-scales) in terms of realization of desired reaction rates and sensitivity. Besides presenting a critical review of present advancements made in the synthesis of NEMs, this article touches upon aspects related to various applications concomitantly. The article concludes with the author’s summary of the insurmountable challenges and the road ahead toward the deployment of nanoenergetic materials in practical applications. The real challenge lies in the ability to preserve the self-assembly of fuel and oxidizer nanoparticles achieved at the nanoscale while synthesizing macroscale energetic formulations using advanced fabrication techniques both in bulk and thin film forms. Most importantly, these self-assembled NEMs have to exhibit excellent combustion performance at reduced sensitivity to external stimuli such as electrostatic discharge (ESD), friction and impact. Full article

Biopolymers exhibit a large variety of attractive properties including biocompatibility, flexibility, gelation ability, and low cost. Therefore, especially in more recent years, they have become highly suitable for a wider and wider range of applications stretching across several key sectors such as those related to food packaging, pharmaceutic, and medical industries, just to name a few. Moreover, biopolymers’ properties are known to be strongly dependent on the molecular arrangements adopted by such chains at the nanoscale and microscale. Fortunately, these arrangements can be altered and eventually optimized through a plethora of more or less efficient polymer processing methods. Here, we used a space-confined solvent vapor annealing (C-SVA) method to subject various biopolymers to rich swelling in solvent vapors in order to favor their further crystallization or self-assembly, with the final aim of obtaining thin biopolymer films exhibiting more ordered chain conformations. The results obtained by atomic force microscopy revealed that while the gelatin biopolymer nucleated and then crystallized into granular compact structures, other biopolymers preferred to self-assemble into (curved) lamellar rows composed of spherical nanoparticles (glycogen and chitosan) or into more complex helix-resembling morphologies (phytagel). The capability of the C-SVA processing method to favor crystallization and to induce self-assembly in various biopolymeric species or even monomeric units further emphasizes its great potential in the future structuring of a variety of biological (macro)molecules. Full article

Self-assembled gold and silver nanoparticles were fabricated in medium vacuum conditions on Corning glass substrates by means of DC magnetron sputtering. The samples were deposited either at 420 °C or 440 °C, or they were initially deposited at room temperature followed by post annealing. Subsequently, they were covered with three different polymers, namely Polystyrene-block-polybutadiene-blockpolystyrene (PS-b-PBD-b-PS), Polystyrene-co-methyl methacrylate (PS-co-PMMA) and Polystyreneblock-polyisoprene-block-polystyrene (PS-b-PI-b-PS), using spin coating. Localized surface plasmon resonances were recorded in the temperature range of −25 °C–100 °C. We show that the resonance position changes systematically as a function of temperature. Theoretical calculations carried out via the Rigorous Coupled Wave Analysis support the experimental results. Based on these findings, the investigated materials demonstrate potential as components for the development of temperature sensors. Full article

The growing demand for wearable and attachable displays has sparked significant interest in flexible quantum-dot light-emitting diodes (QLEDs). However, the challenges of fabricating and operating QLEDs on flexible substrates persist due to the lack of stable and low-temperature processable charge-injection/-transporting layers with aligned energy levels. In this study, we utilized NiO_x nanoparticles that are compatible with flexible substrates as a hole-injection layer (HIL). To enhance the work function of the NiO_x HIL, we introduced a self-assembled dipole modifier called 4-(trifluoromethyl)benzoic acid (4–CF₃–BA) onto the surface of the NiO_x nanoparticles. The incorporation of the dipole molecules through adsorption treatment has significantly changed the wettability and electronic characteristics of NiO_x nanoparticles, resulting in the formation of NiO(OH) at the interface and a shift in vacuum level. The alteration of surface electronic states of the NiO_x nanoparticles not only improves the carrier balance by reducing the hole injection barrier but also prevents exciton quenching by passivating defects in the film. Consequently, the NiO_x-based red QLEDs with interfacial modification demonstrate a maximum current efficiency of 16.1 cd/A and a peak external quantum efficiency of 10.3%. This represents a nearly twofold efficiency enhancement compared to control devices. The mild fabrication requirements and low annealing temperatures suggest potential applications of dipole molecule-modified NiO_x nanoparticles in flexible optoelectronic devices. Full article