Search Results (1,434)

The discharge of oily wastewater threatens the ecosystem and human health, and the efficient treatment of oily wastewater is confronted with problems of high mass transfer resistance at the oil-water-solid multiphase interface, significant light shielding effect, and easy deactivation of photocatalysts. Although traditional physical separation methods avoid secondary pollution by chemicals and can effectively separate floating oil and dispersed oil, they are ineffective in removing emulsified oil with small particle sizes. To address these complex challenges, photocatalytic technology and photocatalysis-based improved technologies have emerged, offering significant application prospects in degrading organic pollutants in oily wastewater as an environmentally friendly oxidation technology. In this paper, the degradation mechanism, kinetic mechanism, and limitations of conventional photocatalysis technology are briefly discussed. Subsequently, the surface interface modulation functions of metal doping and heterojunction energy band engineering, along with their applications in enhancing the light absorption range and carrier separation efficiency, are reviewed. Focus on typical studies on the separation and degradation of aqueous and oily phases using photocatalytic membrane technology, and illustrate the advantages and mechanisms of photocatalysts loaded on the membranes. Finally, other new approaches and converging technologies in the field are outlined, and the challenges and prospects for the future treatment of oily wastewater are presented. Full article

Educational buildings, including schools, nurseries and universities, face stricter regulation and design control on indoor air quality (IAQ) and thermal conditions than other built environments, as these may affect children’s health and wellbeing. In this scoping review, wide-ranging health, performance, and absenteeism consequences of poor—and benefits of good—IAQ and thermal conditions are evaluated, focusing on source control, ventilation and air purification interventions. Economic impacts of interventions in educational buildings have been evaluated to enable the assessment of tangible building-related costs and savings, alongside less easily quantifiable improvements in educational attainment and reduced healthcare. Key recommendations are provided to assist decision makers in pathways to provide clean air, at an optimal temperature for students’ learning and health outcomes. Although the role of educational buildings can be challenging to isolate from other socio-economic confounders, secondary short- and long-term impacts on attainment and absenteeism have been demonstrated from the health effects associated with various pollutants. Sometimes overlooked, source control and repairing existing damage can be important cost-effective methods in minimising generation and preventing ingress of pollutants. Existing ventilation standards are often not met, even when mechanical and hybrid ventilation systems are already in place, but can often be achieved with a fraction of a typical school budget through operational and maintenance improvements, and small-scale air-cleaning and ventilation technologies, where necessary. Full article

With increasing urban economic development, some industrial parks and residential areas are being situated adjacent to each other, creating a potential risk of soil and groundwater contamination from the wastewater and solid waste produced by enterprises. This contamination poses a threat to the health of nearby residents. Currently, groundwater pollution prevention and control zoning in China primarily targets groundwater environmental pollution risks and does not consider the health risks associated with groundwater exposure in industry–city integration areas. Therefore, a scientific assessment of environmental risks in industry–city integration areas is essential for effectively managing groundwater pollution. This study focuses on the high frequency and rapid pace of human activities in industry–city integration areas. It combines health risk assessment and groundwater pollution simulation results with traditional groundwater pollution control classification outcomes to develop a groundwater pollution risk zoning framework specifically suited to these integrated areas. Using this framework, we systematically assessed groundwater pollution risks in a representative industry–city integration area in the middle reaches of the Yangtze River in China and delineated groundwater pollution risk zones to provide a scientific basis for local groundwater environmental management. The assessment results indicate that the total area of groundwater pollution risk control zones is 30.37 km², accounting for 19.06% of the total study area. The first-level control zone covers 5.38 km² (3.38% of the total area), while the secondary control zone spans 24.99 km² (15.68% of the total area). The first-level control zone is concentrated within industrial clusters, whereas the secondary control zone is widely distributed throughout the region. In comparison to traditional assessment methods, the zoning results derived from this study are more suitable for industry–city integration areas. This study also provides groundwater management recommendations for such areas, offering valuable insights for groundwater control in integrated industrial–residential zones. Full article

Iopamidol (IPM), as a typical recalcitrant emerging pollutant and precursor of iodinated disinfection by-products (I-DBPs), is unsuccessfully removed by conventional wastewater treatment processes. This study comprehensively evaluated the ozone/peracetic acid (O₃/PAA) process for IPM degradation, focusing on degradation kinetics, environmental impacts, transformation products, ecotoxicity, disinfection byproducts (DBPs), and microbial inactivation. The O₃/PAA system synergistically activates PAA via O₃ to generate hydroxyl radicals (^•OH) and organic radicals (CH₃COO^• and CH₃CO(O)O^•), achieving an IPM degradation rate constant of 0.10 min⁻¹, which was significantly higher than individual O₃ or PAA treatments. The degradation efficiency of IPM in the O₃/PAA system exhibited a positive correlation with solution pH, achieving a maximum degradation rate constant of 0.23 min⁻¹ under alkaline conditions (pH 9.0). Furthermore, the process demonstrated strong resistance to interference from coexisting anions, maintaining robust IPM removal efficiency in the presence of common aqueous matrix constituents. Furthermore, quenching experiments revealed ^•OH dominated IPM degradation in O₃/PAA system, while the direct oxidation by O₃ and R-O^• played secondary roles. Additionally, based on transformation products (TPs) identification and ECOSAR predictions, the primary degradation pathways were elucidated and the potential ecotoxicity of TPs was systematically assessed. DBPs analysis after chlorination revealed that the O₃/PAA (2.5:3) system achieved the lowest total DBPs concentration (99.88 μg/L), representing a 71.5% reduction compared to PAA alone. Amongst, dichloroacetamide (DCAM) dominated the DBPs profile, comprising > 60% of total species. Furthermore, the O₃/PAA process achieved rapid 5–6 log reductions of E. coli. and S. aureus within 3 min. These results highlight the dual advantages of O₃/PAA in effective disinfection and byproduct control, supporting its application in sustainable wastewater treatment. Full article

In wet flue gas desulfurization and denitrification processes, nitrite accumulation inhibits denitrification efficiency and induces secondary pollution due to its acidic disproportionation. This study developed a Mn-modified ZSM-5 zeolite catalyst, achieving efficient resource conversion of nitrite in nitrogen-containing wastewater through an O₃ + Mn/ZSM-5 catalytic system. Mn/ZSM-5 catalysts with varying SiO₂/Al₂O₃ ratios (prepared by wet impregnation) were characterized by BET, XRD, and XPS. Experimental results demonstrated that Mn/ZSM-5 (SiO₂/Al₂O₃ = 400) exhibited a larger specific surface area, enhanced adsorption capacity, abundant surface Mn³⁺/Mn⁴⁺ species, hydroxyl oxygen species, and chemisorbed oxygen, leading to superior oxidation capability and catalytic activity. Under the optimized conditions of reaction temperature = 40 °C, initial pH = 4, Mn/ZSM-5 dosage = 1 g/L, and O₃ concentration = 100 ppm, the $\mathrm{N}{\mathrm{O}}_2^{-}$ oxidation efficiency reached 94.33%. Repeated tests confirmed that the Mn/ZSM-5 catalyst exhibited excellent stability and wide operational adaptability. The synergistic effect between Mn species and the zeolite support significantly improved ozone utilization efficiency. The O₃ + Mn/ZSM-5 system required less ozone while maintaining high oxidation efficiency, demonstrating better cost-effectiveness. Mechanism studies revealed that the conversion pathway of $\mathrm{N}{\mathrm{O}}_2^{-}$ followed a dual-path catalytic mechanism combining direct ozonation and free radical chain reactions. Practical spray tests confirmed that coupling the Mn/ZSM-5 system with ozone oxidation flue gas denitrification achieved over 95% removal of liquid-phase $\mathrm{N}{\mathrm{O}}_2^{-}$ byproducts without compromising the synergistic removal efficiency of NO_x/SO₂. This study provided an efficient catalytic solution for industrial wastewater treatment and the resource utilization of flue gas denitrification byproducts. Full article

Honey processing is closely linked to water pollution due to the lack of a specific wastewater treatment. This study proposes a sustainable and innovative solution based on two sequential bioprocesses using a real effluent from an Argentine honey-exporting facility. In the initial stage, the honey wastewater was enriched with a non-Saccharomyces yeast (Candida ethanolica), isolated from the same effluent. Treatment with this yeast in a bioreactor nearly doubled the total sugar removal efficiency compared to the control (native flora). Subsequent clarification with diatomaceous earth reduced the optical density (91.6%) and COD (30.9%). In the second stage, secondary sewage effluent was added to the clarified effluent and inoculated with Chlorella vulgaris under different culture conditions. The best microalgae performance was observed under high light intensity and high inoculum concentration, achieving a fivefold increase in cell density, a specific growth rate of 0.752 d⁻¹, and a doubling time of 0.921 d. Although total sugar removal in this stage remained below 28%, cumulative COD removal reached 90% after nine days under both lighting conditions. This study presents the first integrated treatment approach for honey industry effluents using a native yeast–microalgae system, incorporating in situ effluent recycling and the potential for dual waste valorization. Full article

Long-term source apportionment of PM_2.5 during high-pollution periods is essential for achieving sustained reductions in both PM_2.5 levels and their health impacts. This study conducted PM_2.5 sampling in Shenzhen from January to March over the years 2021–2024 to investigate the long-term impact of coronavirus disease 2019 and the short-term impact of the Spring Festival on PM_2.5 levels. The measured average PM_2.5 concentration during the research period was 22.5 μg/m³, with organic matter (OM) being the dominant component. Vehicle emissions, secondary sulfate, secondary nitrate, and secondary organic aerosol were identified by receptor model as the primary sources of PM_2.5 during the observational periods. The pandemic led to a decrease of between 30% and 50% in the contributions of most anthropogenic sources in 2022 compared to 2021, followed by a rebound. PM_2.5 levels in January–March 2024 dropped by 1.4 μg/m³ compared to 2021, mainly due to reduced vehicle emissions, secondary sulfate, fugitive dust, biomass burning, and industrial emissions, reflecting Shenzhen’s and nearby cities’ effective control measures. However, secondary nitrate and fireworks-related emissions rose significantly. During the Spring Festival, PM_2.5 concentrations were 23% lower than before the festival, but the contributions of fireworks burning exhibited a marked increase in both 2023 and 2024. Specifically, during intense peak events, fireworks burning triggered sharp, short-term spikes in characteristic metal concentrations, accounting for over 50% of PM_2.5 on those peak days. In the future, strict control over vehicle emissions and enhanced management of fireworks burning during special periods like the Spring Festival are necessary to reduce PM_2.5 concentration and improve air quality. Full article

Ozone pollution decreases rice yield and quality in general, but how ozone stress changes grain-filling capacity is unclear. A chamber experiment was conducted to compare the effects of ozone exposure during the rice growth season on the grain-filling capacity and quality of spikelets located on the upper primary rachis (superior spikelets, SS) and the lower secondary rachis (inferior spikelets, IS). Ozone stress significantly decreased filled grain percentage by 41.4% and grain mass by 10.2% in IS, but had little effect on grain-filling capacity in SS. Consistent with the reduction in grain mass, ozone stress decreased grain volume, mainly due to reduced grain thickness, and IS was reduced more than SS. After removing the hull, brown rice obtained from ozone treatment exhibited higher proportions of immature and abnormal kernels, resulting in a substantially lower proportion of perfect kernels. Under ozone stress, the proportion of perfect kernels was only one-third in IS, compared with two-thirds in SS. Ozone stress affected the pasting properties of brown rice for both SS and IS, as shown by the decreased amylose content, and the increased maximum viscosity, minimum viscosity, final viscosity, setback, and peak time of the rapid visco analyzer profile. Out of fourteen traits related to nutritional quality of brown rice, only five showed significant increases under ozone stress, and they were the concentrations of albumin, prolamin, sulfur, copper, and manganese. The differential ozone responses between SS and IS were rather small for rice pasting properties and chemical compositions as shown by very few significant interactions between ozone and grain position. It is concluded that ozone stress during plant growth imposed more adverse effects on IS than SS in terms of grain-filling capacity and appearance quality, suggesting an enlarged asynchronous grain-filling pattern in rice panicles under ozone pollution. Strategies to improve the grain-filling capacity of IS are needed to mitigate ozone-induced damage to rice production. Full article

Fumonisin B1, deoxynivalenol (DON), and zearalenone (ZEA) are toxic secondary metabolites produced by Fusarium molds. These mycotoxins are common food and feed pollutants and represent a risk to human and animal health. Although the mycotoxins produced by this genus can cross the blood–brain barrier in many species, their effect on neuronal function remains unclear. We investigated the cell viability effects of these toxins on specified neural cell types, including mouse primary neuronal, astroglial, and mixed-cell cultures 24 or 48 h after mycotoxin administration. DON decreased cell viability in a dose-dependent manner, independent of the culture type. Fumonisin B1 was toxic in pure neuronal cultures only at high doses, but toxicity was attenuated in mixed and pure astroglial cultures. ZEA had significant effects on all culture types in 10 nM by increasing cell viability and network activity, as revealed by multi-electrode array measurements. Since ZEA is a mycoestrogen, we analyzed the effects of ZEA on the expression of estrogen receptor isotypes ERα and ERβ and the mitochondrial voltage-dependent anion channel via qRT-PCR. In neuronal and mixed cultures, ZEA administration decreased ERα expression, while in astroglial cultures, it induced the opposite effect. Thus, our results emphasize that Fusarium mycotoxins act in a cell-specific manner. Full article

The widespread use of bacteria in bioremediation led us to consider what Compulsory Secondary Education (ESO) and Baccalaureate students know about prokaryotes and what their attitudes towards them are. This study focuses on the analysis of the arguments made by secondary school students from several Spanish schools regarding the application of bioremediation to eliminate polluting plastics from the environment. Semi-structured interviews were used to obtain information on descriptive aspects regarding the application of biotechnology to bioremediation. This instrument allows for a better understanding of what students know about biotechnology and what they value when adopting a particular attitude towards improving the environment through systematic observations and recording spontaneously occurring events. The arguments used by these students were analyzed from the perspective of the knowledge and values they consider when making their justifications. It was observed that the students viewed the use of microorganisms to treat waste positively and valued the environmental impact and scientific progress, although they had doubts about certain technical aspects. A teaching approach based on the biodegradation of plastics encourages critical thinking and can be integrated transversally into teaching, promoting debates and reflections on science and values. It is recommended that these types of activities continue to be developed to improve science education. Full article

Industrial effluents pose a significant concern because they contain a variety of metals and metalloids that have detrimental effects on the environment. Conventional techniques are widely used in effluent treatment plants (ETPs) to remove metallic pollutants; however, they are less effective, are costly, and generate secondary toxic waste. Mycosorbent would be a sustainable and economical alternative to conventional techniques, as it offers numerous advantages. In this study, we shed light on the development of mycosorbent, which could be potentially applicable in the treatment of industrial effluent. In a competitive (i.e., multimetal system) optimisation study, mycosorbent AD2 exhibited a maximum biosorption capacity of 3.7 to 6.20 mg/g at pH 6.0, with an initial metal ion concentration of 25 mg/L, a contact time of 2 h, at 50 ± 2 °C, and a pH_PZC of 5.3. The metal-removal capacity increased up to 1.23-fold after optimisation. The thermodynamic parameters confirmed that the AD2 mycosorbent facilitated an endothermic, feasible, and spontaneous biosorption process. The FT-IR and SEM characterisation analysis confirmed the adsorption of metals on the surface of the mycosorbent from the aqueous system. This study demonstrated that mycosorbent could be an effective tool for combating metallic pollutants in various industrial effluents. Full article

Air pollution acts as a pervasive oxidative stressor, disrupting global crop production and ecosystem health through the overproduction of reactive oxygen species (ROS). Hazardous pollutants impair critical physiological processes—photosynthesis, respiration, and nutrient uptake—triggering oxidative damage and yield losses. This review synthesizes current knowledge on plant defense mechanisms, emphasizing the integration of enzymatic (SOD, POD, CAT, APX, GPX, GR) and non-enzymatic (polyphenols, glutathione, ascorbate, phytochelatins) antioxidant systems to scavenge ROS and maintain redox homeostasis. We highlight the pivotal roles of transcription factors (MYB, WRKY, NAC) in orchestrating stress-responsive gene networks, alongside MAPK and phytohormone signaling (salicylic acid, jasmonic acid, ethylene), in mitigating oxidative stress. Secondary metabolites (flavonoids, lignin, terpenoids) are examined as biochemical shields against ROS and pollutant toxicity, with evidence from transcriptomic and metabolomic studies revealing their biosynthetic regulation. Furthermore, we explore biotechnological strategies to enhance antioxidant capacity, including overexpression of ROS-scavenging genes (e.g., TaCAT3) and engineering of phenolic pathways. By addressing gaps in understanding combined stress responses, this review provides a roadmap for developing resilient crops through antioxidant-focused interventions, ensuring sustainability in polluted environments. Full article

Reducing the application of chemical fertilizers and remediating heavy metal pollution in soil are important directions in current agricultural research. Utilizing the plant-growth-promoting and remediation capabilities of bacteria can provide more environmentally friendly assistance to agricultural production. In this study, the Burkholderia alba YIM B08401 strain was isolated and identified from rhizospheric soil, subjected to whole-genome sequencing and analysis, and its Cd²⁺ adsorption efficiency and characteristics were confirmed using multiple experimental methods, including atomic absorption spectrometry (AAS), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS). The results showed that the genome of strain YIM B08401 has a total length of 7,322,157 bp, a GC content of 66.39%, and predicts 6504 protein-coding sequences. It contains abundant functional genes related to nutrient conversion (phosphate solubilization, sulfur metabolism, zinc solubilization, siderophore production), plant hormone regulation (indole-3-acetic acid secretion, ACC deaminase production), phenolic acid degradation, root colonization, heavy metal tolerance, pathogen antagonism, and the production of antagonistic secondary metabolites. Additionally, strain YIM B08401 can specifically bind to Cd²⁺ through various functional groups on the cell surface, such as C-O-C, P=O, and O-H, enabling biosorption. In conclusion, strain YIM B08401 is an excellent strain with plant-growth-promoting, disease-resistant, and bioremediation capabilities, warranting further development as a biofertilizer for agricultural applications to promote green and sustainable agricultural development. Full article

According to Victor Ernest Shelford’s ‘Law of Tolerance,’ organisms within ecosystems thrive optimally when environmental conditions are favorable. Applying this principle to ecosystems and agro-ecosystems facing water scarcity or environmental challenges can significantly enhance their productivity. In these ecosystems, phytocenosis adjusts its conditions by utilizing water with varying salinity levels. Moreover, establishing optimal drinking water conditions for human populations within an ecosystem can help mitigate future negative succession processes. The purpose of this study is to evaluate the quality of two distinct water sources in the Amudarya district of the Republic of Karakalpakstan, Uzbekistan: collector-drainage water and groundwater at depths of 10 to 25 m. This research is highly relevant in the context of climate change, as improper management of water salinity, particularly in collector-drainage water, may exacerbate soil salinization and degrade drinking water quality. The primary methodology of this study is as follows: The Food and Agriculture Organization of the United Nations (FAO) standard for collector-drainage water is applied, and the water quality index is assessed using the CCME WQI model. The Canadian Council of Ministers of the Environment (CCME) model is adapted to assess groundwater quality using Uzbekistan’s national drinking water quality standards. The results of two years of collected data, i.e., 2021 and 2023, show that the water quality index of collector-drainage water indicates that it has limited potential for use as secondary water for the irrigation of sensitive crops and has been classified as ‘Poor’. As a result, salinity increased by 8.33% by 2023. In contrast, groundwater quality was rated as ‘Fair’ in 2021, showing a slight deterioration by 2023. Moreover, a comparative analysis of CCME WQI values for collector-drainage and groundwater in the region, in conjunction with findings from Ethiopia, India, Iraq, and Turkey, indicates a consistent decline in water quality, primarily due to agriculture and various other anthropogenic pollution sources, underscoring the critical need for sustainable water resource management. This study highlights the need to use organic fertilizers in agriculture to protect drinking water quality, improve crop yields, and promote soil health, while reducing reliance on chemical inputs. Furthermore, adopting WQI models under changing climatic conditions can improve agricultural productivity, enhance groundwater quality, and provide better environmental monitoring systems. Full article

In this study, the BPTCD/g-C₃N₄ heterojunction photocatalyst was successfully prepared by the hydrothermal method. BPTCD (3,3′,4,4′-benzophenone tetracarboxylic dianhydride) is immobilised on the surface of g-C₃N₄ by non-covalent π-π stacking. The BPTCD/g-C₃N₄ heterojunction photocatalyst is an all-organic photocatalyst with significantly improved photocatalytic performance compared with g-C₃N₄. BPTCD/g-C₃N₄-60% was able to effectively degrade MO solution (10 mg/L) to 99.9% and 82.8% in 60 min under full spectrum and visible light. The TOC measurement results indicate that MO can ultimately be decomposed into H₂O and CO₂ through photocatalytic action. The photodegradation of methyl orange by BPTCD/g-C₃N₄ composite materials under sunlight is mainly attributed to the successful construction of the heterojunction structure and its excellent π-π stacking effect. Superoxide radicals (^•O₂⁻) were found to be the main active species, while ^•OH and h⁺ played a secondary role. The synthesised BPTCD/g-C₃N₄ also showed excellent stability in the activity of photodegradation of MO in wastewater, with the performance remaining above 90% after three cycles. The mechanism of the photocatalytic removal of MO dyes was also investigated by the trap agent experiments. Additionally, BPTCD/g-C₃N₄-60% demonstrated exceptional photodegradation performance in the degradation of methylene blue (MB). BPTCD/g-C₃N₄ heterojunctions have great potential to degrade organic pollutants in wastewater under solar irradiation conditions. Full article