Search Results (24)

In this study, phosphogypsum waste collected from a factory dump in Kedainiai, Lithuania, was used for the first time as a starting material in the dissolution–precipitation synthesis of high-quality bioceramic calcium hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂; CHA). The CHA powders were synthesized using the dissolution–precipitation method, employing phosphogypsum in four different conditions: untreated, dried at 100 °C, dried at 150 °C, and annealed at 1000 °C. Various phosphorus sources were used in the CHA synthesis process: Na₂HPO₄; a mixture of Na₂HPO₄ and NaH₂PO₄; or a combination of Na₂HPO₄, NaH₂PO₄, and NaHCO₃. These mixtures were allowed to react at 80 °C for 48 h, 96 h, 144 h, and 192 h. X-ray diffraction (XRD) analysis revealed slight variations in the synthesized products depending on the specific starting materials used. Fourier transform infrared spectroscopy (FTIR) was conducted to confirm the structural characteristics of the synthesized CHA samples. The surface microstructure of the synthesized CHA samples differed notably from that of the raw phosphogypsum. All synthesized CHA samples exhibited Type IV nitrogen adsorption–desorption isotherms with H3-type hysteresis loops, indicating the presence of mesoporous structures, typically associated with slit-like pores or aggregates of plate-like particles. To the best of our knowledge, an almost monophasic CHA has been fabricated from phosphogypsum waste for the first time using a newly developed dissolution–precipitation synthesis method. A key challenge in the high-end market is the development of alternative synthesis technologies that are not only more environmentally friendly but also highly efficient. These findings demonstrate that phosphogypsum is a viable and sustainable raw material for CHA synthesis, with promising applications in the medical field, including the production of artificial bone implants. Full article

Processing of meat waste into meat and bone meal generates wastewater that must be properly treated to minimize its environmental impact. In addition to its high organic load, it contains microorganisms, including pathogens, that pose a threat to human health. In this study, wastewater from meat and bone meal production was treated using the Fenton process with a variable Fe²⁺/H₂O₂ mass ratio ranging from 1:2 to 1:10, followed by neutralization with lime milk. A microbiological analysis was performed on both the raw wastewater and the liquid fractions obtained after treatment, along with additional analyses of selected physicochemical parameters. The identification of isolated microorganisms was carried out using the MALDI-TOF MS technique. Qualitative analysis of the treated wastewater samples showed the presence of microorganisms belonging to the genera Staphylococcus, Enterococcus, Alcaligenes, and Pseudomonas. Staphylococcus aureus and Alcaligenes faecalis were present in each of the treated samples. The Fenton process effectively reduced the total number of microorganisms, with the lowest counts of 1.3 × 10² CFU/mL and 3.2 × 10² CFU/mL found in wastewater samples treated with Fe²⁺/H₂O₂ mass ratios of 1:8 and 1:10, which correlated with higher doses of hydrogen peroxide. Full article

The aim of the circular economy is to treat waste as a valuable raw material, reintegrating it into the industrial economy and extending the lifecycle of subsequent products. Efforts to reduce the production of hard-to-recycle waste are becoming increasingly important to manufacturers, not only of consumer goods but also of specialized items that are difficult to manufacture, such as medical supplies, which have now become a priority for the European Union. The purpose of the study is to manufacture a novel human-purified type I collagen membrane from bone remnants typically discarded during the processing of cortico-cancellous bones in tissue banks and to evaluate its mechanical properties and effectiveness in regenerating bone-critical mandibular defects in rabbits. To prepare the novel membrane, cortico-cancellous bone chip samples from a local tissue bank were processed to isolate collagen by demineralization under agitation in HCl, cast into a silicone mold, and air-dried at room temperature and UV irradiation. The average thickness of the four batches analyzed by SEM was 37.3 μm. The average value of Young’s modulus and tensile strength obtained from the specimens was 2.56 GPa and 65.43 Mpa, respectively. The membrane’s efficacy was tested by creating a critical bicortical and bilateral osteoperiosteal defect in rabbit mandibles. The right-side defects were covered with the collagen membrane, while the left-side defects were left untreated as a control. Nine weeks post-surgery, clinical, radiological, and histological analyses demonstrated new bone formation in the treated areas, whereas the control sites showed no bone regeneration. This innovative approach not only contributes to sustainability in healthcare by optimizing biological waste but also exemplifies efficient resource use in line with the circular economy, offering a cost-effective, biocompatible option that could benefit national health systems. Full article

The present study aimed at converting meat industry waste, particularly waste bones and chicken feathers, into biochar to recycle valuable nutrients present in it, which ultimately become part of the municipal waste. The bone biochar (BB) and feathers biochar (FB) were prepared at 550 °C, and their potential was evaluated as an organic amendment for the growth of sunflower. The ash content (AC) and fixed carbon (FC) improved significantly in prepared biochars as compared to raw feedstock. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analyses signaled the occurrence of various functional groups viz. amide group and hydroxyapatite, porosity, and multiple nutrients. Application of BB and FB in potted soil alone as well as in composites (1:1, 1:2, 2:1) at 1%, 3%, and 5% (w/w) and synthetic fertilizer significantly increased soil pH, electrical conductivity (EC_e), organic matter (OM) and water holding capacity (WHC), while reducing the bulk density (BD). The growth of plants grown in soil treated with a 2:1 composite of feathers and bone biochar at 5% application rate showed significantly greater differences in plant height, total chlorophyll content, and plant dry weight than the control but was comparable to growth with chemical fertilizer, rendering it a potential alternative to chemical-based synthetic fertilizer. Full article

Recycling and reusing phosphorus in agriculture can reduce the consumption of natural phosphorus resources, which are continuing to shrink. Phosphorus fertilizers made from renewable raw materials (sewage sludge ash, animal bones, dried animal blood) and activated with phosphorus solubilizing microorganisms (Bacillus megaterium, Acidithiobacillus ferrooxidans) offer an alternative to conventional fertilizers. These products should meet consumer and environmental safety standards. In this paper, based on field experiments conducted in northeast Poland, the effects of waste-derived biofertilizers on selected parameters of wheat yield quality are discussed. The study focuses on the technological properties of the grain (hectoliter weight, hardness index, Zeleny index, starch, wet gluten, and protein content), the content of proteogenic amino acids, macro- and micronutrients, and selected toxic elements in the grain. The quality parameters of wheat grain were not affected by the tested biofertilizers applied in P doses up to 35.2 kg ha⁻¹, nor by conventional fertilizers. Full article

Natural and renewable sources of calcium carbonate (CaCO₃), also referred to as “biogenic” sources, are being increasingly investigated, as they are generated from a number of waste sources, in particular those from the food industry. The first and obvious application of biogenic calcium carbonate is in the production of cement, where CaCO₃ represents the raw material for clinker. Overtime, other more added-value applications have been developed in the filling and modification of the properties of polymer composites, or in the development of biomaterials, where it is possible to transform calcium carbonate into calcium phosphate for the substitution of natural hydroxyapatite. In the majority of cases, the biological structure that is used for obtaining calcium carbonate is reduced to a powder, in which instance the granulometry distribution and the shape of the fragments represent a factor capable of influencing the effect of addition. As a result of this consideration, a number of studies also reflect on the specific characteristics of the different sources of the calcium carbonate obtained, while also referring to the species-dependent biological self-assembly process, which can be defined as a more “biomimetic” approach. In particular, a number of case studies are investigated in more depth, more specifically those involving snail shells, clam shells, mussel shells, oyster shells, eggshells, and cuttlefish bones. Full article

This paper studies the thermal, morphological, and mechanical properties of 3D-printed polylactic acid (PLA) blends of virgin and recycled material in the following proportions: 100/0, 25/75, 50/50, and 75/25, respectively. Real waste, used as recycled content, was shredded and sorted by size without a washing step. Regular dog-bone specimens were 3D printed from filaments, manufactured in a single screw extruder. Thermogravimetric analysis indicated that adding PLA debris to raw material did not significantly impact the thermal stability of the 3D-printed samples and showed that virgin and recycled PLA degraded at almost the same temperature. Differential scanning calorimetry revealed a significant reduction in crystallinity with increasing recycled content. Scanning electron microscopy showed a more homogenous structure for specimens from 100% pure PLA, as well as a more heterogeneous one for PLA blends. The tensile strength of the PLA blends increased by adding more recycled material, from 44.20 ± 2.18 MPa for primary PLA to 52.61 ± 2.28 MPa for the blend with the highest secondary PLA content. However, this study suggests that the mechanical properties of the reprocessed parts and their basic association are unique compared with those made up of virgin material. Full article

Fishery residues are abundant raw materials that also provide numerous metabolites with high added value. Their classic valorization includes energy recovery, composting, animal feed, and direct deposits in landfills or oceans along with the environmental impacts that this entails. However, through extraction processes, they can be transformed into new compounds with high added value, offering a more sustainable solution. The aim of this study was to optimize the extraction process of chitosan and fish gelatin from fishery waste and their revalorization as active biopolymers. We successfully optimized the chitosan extraction process, achieving a yield of 20.45% and a deacetylation degree of 69.25%. For the fish gelatin extraction process, yields of 11.82% for the skin and 2.31% for the bone residues were achieved. In addition, it was demonstrated that simple purification steps using activated carbon improve the gelatin’s quality significantly. Finally, biopolymers based on fish gelatin and chitosan showed excellent bactericidal capabilities against Escherichia coli and Listeria innocua. For this reason, these active biopolymers can stop or decrease bacterial growth in their potential food packaging applications. In view of the low technological transfer and the lack of information about the revalorization of fishery waste, this work offers extraction conditions with good yields that can be easily implemented in the existing industrial fabric, reducing costs and supporting the economic development of the fish processing sector and the creation of value from its waste. Full article

This study presents the developing process of the Śmiłowo Eco-Park, located in the Noteć valley region (Poland), is a part of the biggest Polish agri-food consortium, from its initial small waste management company to its final structure as an eco-industrial park using industrial symbiosis methods. The industrial symbiosis applied in the Eco-park promotes a business model which covers the whole life cycle of the products starting from the plant growing by animal feed preparation, livestock breeding, meat preparations, meat-bone meal production from animal waste, and the use of pig slurry as a fertilizer. The Eco-park model is presented in the form of a system of connected stream flows of materials and energy covering the full lifecycle of products, from cereal cultivation, through the production of industrial feed, and poultry and pig breeding for the production of meat products. The solutions used include the prevention of environmental pollution through the modernization of existing processes, implementation of new technologies, reduction of waste and its reuse, recycling, and recovery of materials and energy, the substitution of raw materials with waste, and thermal treatment of waste and its use as biofuel. This case study allows for analyses of the organizational and technical key strategic activities which enable waste, including hazardous waste, to be transformed into valuable materials and energy. These activities have modified the system of material and energy flows through the value chain to realize the goal of allowing profitable management of waste according to circular economy methods and also indicates methods of supporting modifications of supply chains in terms of implementation of the industrial symbiosis business model according to its relationship with sustainable development, cleaner production, and circular economy models. EIP Śmiłowo annually utilizes 300,000 t meat waste, produces 110,000 t meat bone meal biofuel, uses 120,000 t of pig manure as fertilizers, produces 460,000 GJ bioenergy, eliminates 92,000 t CO₂ emissions. Full article

Animal waste can serve as a raw material source for feed preparation, and can also be used, after appropriate processing, as fuel, fertilizer, biogas, and other useful products. In addition, the practical use of these wastes eliminates their mandatory disposal. Recycling animal waste is a feature of the circular economy, leading to environmental sustainability. In this regard, we conducted a search and review of contemporary scientific publications from open sources, including publications and data from Internet portals, Web of Science, Scopus scientometric databases, websites of patent offices, libraries, and reading rooms. It has been found that animal by-products are desirable for use in combination with vegetable protein sources. The 15 most relevant types of animal waste and their use are indicated based on current scientific publications. Moreover, 13 types of feed of animal origin, along with their purposes and descriptions, are also identified. Current scientific publications and research on the processing of insects into feed; the use of bird droppings, meat, and bone and bone meal; and the processing of seafood waste, bird waste, and eggshells are reviewed. As a result, firstly, the most important types of technological equipment involved in animal waste processing technologies, particularly devices for drying, grinding, and mixing, are analyzed and discussed. Secondly, technologies for processing waste into useful products of animal origin are analyzed and discussed. Full article

This paper puts forward the use of “low-cost/low-end” hydroxyapatite-based adsorbing materials prepared from Tambaqui fish cleaning residues (i.e., bones) by grinding and/or thermal annealing. The nature of raw materials and treatments practically resulted in a “zero-cost” adsorbent for atrazine pesticide and Co²⁺ ion remediation in an aqueous solution. Despite the distinctive character of the two contaminants, all adsorptions were found to follow pseudo-second order kinetics and Freundlich isotherm models. Pristine hydroxyapatite proved to be more effective in adsorbing atrazine at low concentrations due to interactions with collagen residues. Conversely, heat-treated materials demonstrated better adsorption performances for cobalt due to the removal of organic residues hindering access to the surface. On the other hand, lower adsorption affinities resulted into a faster and more efficient Co²⁺ release into water. The different behavior in terms of phosphate and cobalt release shown by the three hydroxyapatite-based absorbents can be exploited for differential liberation of targeted nutrients, with high seed germination rates. Considering circular economic principles, waste-derived hydroxyapatites may be potentially attractive for removing ionic species, minimizing water pollution stemming from heavy industry, and for their subsequent targeted release to edible plants, enhancing agricultural availability of mineral nutrients for soil fertilization. Full article

Milkfish (Chanos chanos) is an abundant fish commodity in the Philippines that generates a large number of wastes such as skin, scales, viscera, and bones, which, upon disposal, cause environmental pollution. The abundance of these wastes, such as fish skin, rich in bioactive natural products such as collagen, elicits interest in their conversion into high-market-value products. The decellularization of milkfish skin waste can extract its extracellular matrix (ECM), a potential raw material for biomedical applications such as the repair of damaged skin tissues. In particular, this study characterized the developed decellularized ECM with different concentrations (0.1%, 1.0%) of the decellularizing agents (Triton X-100, SDS) and temperature (4 °C, room temperature) using milkfish skin. The decellularized ECM structure was better preserved using Triton X-100, while SDS was more effective in cell component removal, especially at 1% concentration and 4 °C temperature. There were significant effects of varying the temperatures and concentrations on the physical and mechanical properties of the decellularized ECM. Future studies could explore more variables to further establish protocols and more analyses to better characterize the decellularized milkfish skin. Full article

This study follows a circular economy approach through the preliminary implementation of a coated porous inorganic material (PIM), studied as sustainable controlled release fertilizer, and its application for lettuce Lactuca sativa L. cultivar Chiara growth. The PIM was made of pumice scraps that partially replaced clay as a natural raw material, spent coffee grounds as a porous agent, bovine bone ash and potassium carbonate to provide phosphorus (P) and potassium (K) nutrients, respectively. A coating made with defatted black soldier fly prepupae biomass was used as a nitrogen (N) source. Most of the ingredients used were industrial residues, with the aim of valorizing the raw waste materials present locally. The suitability of PIMs as a fertilizer was investigated with an interdisciplinary approach, which included the first chemical and physical characterization of the material, the evaluation of its antibacterial properties and of its use in horticulture through lettuce growth tests. As tests were carried out indoors, a specific LED lighting device was used to grow the lettuce. The release of nutrients into the soil was estimated by measuring the main elements in the fertilizers before and after their use in the soil. The first results from this characterization study support PIMs’ suitability for agronomic applications. The use of the PIMs suggested average higher dry weight (49%), fresh weight (112%), and leaf area (48%), compared to those with the use of a standard fertilizer soil, without the release of any dangerous element for the plant in the soil. These results are a promising beginning for the development of further studies already in progress on sustainable controlled-release fertilizers. Full article

The nontoxicity, worldwide availability and low production cost of cuttlefish bone products qualify them an excellent biocoagulant to treat food industry wastewater. In this study, cuttlefish bone liquid waste from the deproteinization step was used as a biocoagulant to treat food industry wastewater. This work concerns a waste that has never before been investigated. The objectives of this work were: the recovery of waste resulting from cuttlefish bone deproteinization, the replacementof chemical coagulants with natural ones to preserve the environment, and the enhancement ofthe value of fishery byproducts. A quantitative characterization of the industrial effluents of a Moroccan food processing plant was performed. The physicochemical properties of the raw cuttlefish bone powder and the deproteinization liquid extract were determined using specific analysis techniques: SEM/EDX, FTIR, XRD and ¹H-NMR. The protein content of the deproteinization liquid was determined by OPA fluorescent assay. The zeta potential of the liquid extract was also determined. The obtained analytical results showed that the deproteinization liquid waste contained an adequate amount of soluble chitin fractions that could be used in food wastewater treatment. The effects of the coagulant dose and pH on the food industrial effluents were studied to confirm the effectiveness of the deproteinization liquid extract. Under optimal conditions, the coagulant showed satisfactory results. Process optimization was performed using the Box–Behnken design and response surface methodology. Thus, the optimal removal efficiencies predicted using this model for turbidity (99.68%), BOD₅ (97.76%), and COD (82.92%) were obtained at a dosage of 8 mL biocoagulant in 0.5 L of food processing wastewater at an alkaline pH of 11. Full article

The meat industry generates a large amount of animal by-products not only derived from the slaughter process but also due to the losses and waste of meat products along the supply chain, contributing to the world’s food loss and waste problem. Yearly, 1.7 Mt of meat in the European retail sector and 20% of meat for consumption is wasted in this sector of the supply chain. Therefore, the aim of this paper was to find and evaluate alternatives for the valorisation of agri-food residues, more specifically the meat waste from the food retail sector, through a technological perspective. Thus, we delve into the industrial processes already implemented and the emerging procedures that use muscle, bones and fats by-products from poultry, cattle and pork as the main raw materials in order to identify and characterise them. The results indicate that in addition to the current destinations—landfill, incineration and the rendering process—these animal by-products can be incorporated in the production of biodiesel, food formulations, pharmaceuticals, fertilisers and biogas through an industrial symbiosis approach. Consequently, the several valorisation processes and procedures identified not only suggest an increase in concern about the impacts of the disposal of these materials, but also highlight the potential associated with the use of animal by-products as raw material to obtain added-value products. Full article