Search Results (105)

High-ash coal slime water, characterized by its stable colloidal suspension of fine kaolinite particles, poses a significant challenge in the coal preparation industry because it is hard to achieve efficient solid–liquid separation. While traditional coagulants and flocculants often suffer from limited bridging capabilities and distinct pH sensitivity, novel molecular architectures offer potential solutions. In this study, a star-shaped inorganic–organic hybrid flocculant (Al-PAM) was synthesized via in situ polymerization. Its flocculation performance and interfacial adsorption mechanism on the specifically targeted aluminol basal plane of kaolinite were systematically investigated and compared with Polyaluminum Chloride (PAC), Non-ionic Polyacrylamide (NPAM), and their combination (PAC + NPAM). Settling tests revealed that Al-PAM exhibited superior performance at a significantly lower dosage (10 mg∙L⁻¹) compared to the PAC + NPAM binary reagent system. It achieved a rapid initial settling velocity and reduced the supernatant turbidity to 48.45 NTU, while maintaining a near-neutral pH favorable for water recycling. Furthermore, Quartz Crystal Microbalance with Dissipation (QCM-D) monitoring confirmed that Al-PAM forms a thick, viscoelastic, and irreversible adsorption layer on the Al₂O₃ substrate. The dissipation shifts (ΔD) revealed that the star-shaped architecture promotes distinct bridging and electrostatic adsorption, overcoming the limitation of linear polymers. This work elucidates the specific contribution of the alumina-surface interaction with flocculants and proposes an efficient strategy for treating refractory coal slime water. Full article

Effective treatment of coal slime water is essential for sustainable coal preparation plant operation but hindered by the stable suspension of fine, negatively charged particles. To address this, a novel star-shaped inorganic–organic hybrid polymer (aluminum hydroxide-polyacrylamide, Al-PAM) was synthesized via in situ polymerization. Its performance was systematically compared with well-established coagulants/flocculants—polyaluminum chloride (PAC), non-ionic polyacrylamide (NPAM), and their binary combination through settling tests and quartz crystal microbalance with dissipation monitoring (QCM-D). The results showed a positive correlation between the molecular weight of Al-PAM and its flocculation efficiency. The optimal variant, Al-PAM-442, achieved an exceptionally high initial settling rate (50.4 m/h) and low supernatant turbidity (45.77 NTU) at an ultralow dosage of 6 mg/L. QCM-D analysis elucidated the mechanism: Al-PAM forms a thick, soft, and irreversibly adsorbed hydrated layer on silica, enabling strong electrostatic anchoring and effective polymer bridging. In contrast, PAC adsorption was reversible, while NPAM formed a thin, compact film with poor bridging capacity. Although the combined PAC/NPAM system showed synergistic performance, it required a significantly higher dosage (70 mg/L). This study demonstrates that the star-shaped Al-PAM architecture successfully integrates charge neutralization and bridging into a single molecule, offering a highly efficient and practical solution for industrial coal slurry dewatering. Full article

Quartz Crystal Microbalance with Dissipation monitoring (QCM-D) systems are widely used for the real-time analysis of mass changes and viscoelastic properties in biological samples, enabling applications such as biomolecular interaction studies, biosensing, and fluid characterization. However, their accessibility has been limited by high acquisition costs. To address this limitation, a low-cost, open-source QCM-D system was developed. Unlike other affordable, open-hardware alternatives, this system is specifically optimized for potential biomedical applications by integrating active thermal control to preserve the physical properties of the samples and dissipation monitoring to characterize their viscoelastic behavior. A 10 MHz quartz crystal with a sensor module and a control and acquisition unit were integrated. The full system was built at a total cost below USD 500. Performance validation showed a temperature stability of ±0.13 °C, a frequency stability of ±2 Hz in air, and a limit of detection (LOD) of 0.46% polyethylene glycol (PEG), thereby enabling stable, reproducible measurements and the sensitive detection of small mass and interfacial changes in low-concentration samples. These results demonstrate that key QCM-D sensing capabilities can be achieved at a fraction of the cost, providing an accessible and reliable platform for potential biomedical research. Full article

The combination of supported lipid bilayers (SLBs) with the Quartz Crystal Microbalance with Dissipation monitoring (QCM-D) has been proven to be a powerful tool to simultaneously monitor mass and viscoelastic changes related to membrane binding-events. In this work, the above methodology is employed for the study of the interaction of the Early Endosomal Antigen 1 (EEA1) to a model lipid bilayer that mimics the early endosome (EE) membrane, focusing on the membrane composition. Starting with the formation of a lipid bilayer through the vesicles fusion technique, we investigated the formation of SLBs that incorporate phosphatidylinositol 3-phosphate (PI(3)P), a key component for EEA1 binding, in combination with other lipids, e.g., (1,2-dioleoyl-sn-glycero-3)-phosphocholine (DOPC), -phosphoserine (DOPS), -phosphoethanolamine (DOPE), and cholesterol (Chol). The interaction of the full-length coiled-coil EEA1 to the formed SLBs was further studied in real time with the QCM-D and characterized with respect to the lipid composition and pH. Our findings confirm that PI(3)P is essential for the EEA1–membrane interaction, while it was shown that Chol and phosphatidylserine greatly influence the binding event. In fact, including 30% Chol in a PI(3)P (3%):PS (6%) SLB resulted in almost double EEA1 binding than in the absence of Chol. Moreover, we employed the QCM-viscoelastic model available to analyze the QCM-D data with emphasis on the study of the protein conformation. Our results showed that, in our in vitro system, EEA1 is not fully extended and/or highly packed, but is mainly in a bent, distorted conformation with an average size close to 100 nm. This study complements previous works employing in vitro assays, also demonstrating the ability to reconstitute more complex biomimetic EE membranes containing inositol phospholipids on a QCM surface for the study of EEA1 binding. Full article

This study investigates how molecular weight, ionic strength, and ionic composition influence the performance of sodium lignosulfonate as a dispersant for titanium dioxide (TiO₂) suspensions. Adsorption behavior was quantified using a quartz crystal microbalance with dissipation monitoring (QCM-D), while dispersion efficiency was assessed in concentrated suspensions via particle analysis (LUMiSizer) and in pastes through rheological measurements. In salt-free conditions, no adsorption occurs; however, the observed low particle size and viscosity can be attributed to depletion stabilization by non-adsorbing lignosulfonates. Both low- and high-molecular-weight fractions exhibit dispersing performance, but high-molecular-weight lignosulfonate provides the greatest stability across electrolyte variations. Increasing ionic strength enhances adsorption, leading to elastic particle network formation and higher viscosity due to reduced Debye length. With divalent ions, this effect is stronger and promoted by divalent cation bridging. These findings underscore the importance of tailoring lignosulfonate molecular weight and dosage to operating conditions, supporting formulation strategies for mineral-rich suspensions and industrial effluents. Future work should address long-term stability, temperature effects, and behavior on hydrophobic surfaces. Full article

The study of the conformational stability of protein layers at the interface between gold surfaces and lipid membranes is crucial for determining the biological activity of these systems and understanding their interactions. The surfaces differ significantly in hardness: gold is a rigid substrate, while the POPC/POPS liposome layer is highly flexible. A quartz crystal microbalance with dissipation (QCM-D) monitoring method and multi-parametric surface plasmon resonance (MP-SPR) were used to determine the adsorption efficiency of lysozymes, the level of layer hydration, and changes occurring within the secondary structure and the thickness of the formed protein layer. In both methods, lysozyme adsorption on the gold surface was more effective at pH 4.0 than at pH 7.4. The lysozyme adsorption efficiency on the surface of the lipid layer was the same for both measurement conditions. In contrast, the affinity of lysozyme molecules to the lipid surface was higher than that of the gold surface. The composition of the secondary structure of lysozymes was monitored using the FT-IR method. Deconvolution of the Amide I band confirms the existence of different mechanisms underlying lysozyme molecule immobilization depending on the type of adsorption surface. Along with the change in the surface, there is a transition from the dominance of electrostatic to hydrophobic interactions, which significantly affects the structure of the interphase layer. High content of random structures on the lipid surface is evident, while, in the case of the gold surface, there is a decrease in random structures and the presence of antiparallel β-sheets. Interaction with the surface induces the transition of amyloidogenic domains of the protein to conformations, which are particularly susceptible to aggregation, consequently leading to oligomerization. Full article

This study investigates the formation, physicochemical properties, and interfacial behavior of interpolyelectrolyte complexes (IPECs) composed of chitosan (CS) and sodium alginate (ALG) in aqueous media at pH 4.5. Using a combination of turbidity, ζ-potential, conductivity, and interfacial tension measurements, we explore how mixing protocols and solution composition influence complex formation and stability. The results reveal that while ζ-potential remains largely unaffected by polymer concentration, turbidity and interfacial tension exhibit strong dependence, particularly near the stoichiometric charge equivalence point (Z ≈ 1). These findings suggest that neutral complexes formed at Z ≈ 1 display enhanced aggregation and surface activity, especially when ALG is in excess. Additionally, we extend the study to layer-by-layer (LbL) films assembled from CS and ALG, monitored via Quartz Crystal Microbalance with dissipation (QCM-D). The films exhibit quasi-linear growth and increasing elastic modulus with layer number, indicating uniform deposition and strong interlayer interactions. The viscoelastic properties of the multilayers further confirm the structural integrity and potential applicability of these systems in surface engineering and encapsulation technologies. Overall, this work provides a comprehensive understanding of CS–ALG complexation from bulk to interfacial assemblies. Full article

Penicillin G (PEN) is a widely used antibiotic for treating microbial infections. However, its extensive use in veterinary medicine can lead to accumulation in animal-derived products, particularly milk and meat. This highlights the urgent need for rapid and sensitive antibiotic detection methods. In this study, we employed DNA aptamers for the detection of PEN and for the analysis of aptamer specificity using a combined approach based on quartz crystal microbalance with dissipation monitoring (QCM-D) and localized surface plasmon resonance (LSPR). QCM-D measures changes in resonant frequency, Δf, and dissipation, ΔD, while LSPR monitors wavelength shifts in the extinction spectra corresponding to changes at the surface of gold nanoparticles (AuNPs). Thiolated aptamers were chemisorbed onto the surface of AuNPs with a diameter of 80 nm. In the presence of PEN, a redshift in the extinction spectra and a decrease in resonant frequency were observed, accompanied by an increase in dissipation due to surface viscosity effects. Significant changes in both acoustic and LSPR signals were observed at PEN concentrations as low as 1 nM. The limits of detection (LOD) for PEN, determined by QCM-D (3.0 nM, or 1.05 ng/mL)) and LSPR (3.1 nM, or 1.09 ng/mL), were similar and both were lower than the maximum residue limit (MRL) for PEN established by the EU (4 ng/mL). Full article

The prevalence of food allergies has been steadily increasing in recent years. β-lactoglobulin (β-LG), the main allergenic protein of milk and dairy allergies, is more commonly observed in infants and children. In this study, a β-LG-specific aptamer was selected using the combinatorial chemistry process known as systematic evolution of ligands by exponential enrichment (SELEX), and a quartz crystal microbalance with dissipation monitoring (QCM-D)-based aptasensor was developed using a novel surface functionalization technique, which mimics an artificial cell membrane on the QCM-D sensor surface, creating a physiologically relevant environment for the binding of the target to the sensor. Through SELEX combined with next-generation sequencing (NGS), the aptamer Apt 356 was identified. Its binding to β-LG was confirmed via dot blot analysis. The selected Apt 356 was then used for the development of a QCM-D-based sensor. To fabricate the sensor, the quartz surface was functionalized with a supported lipid bilayer (SLB). The β-LG-specific aptamer was immobilized onto this SLB. The results demonstrated that the QCM-D system allows real-time observation and evaluation of the binding of β-LG. While there have been some studies on aptasensors for the β-LG protein, to the best of our knowledge, this is the first QCM-D-based aptasensor developed specifically for β-LG protein detection. Full article

The solid electrolyte interphase (SEI) on the anode of lithium-ion batteries (LIBs) has been studied thoroughly due to its crucial importance to the battery’s long-term performance. At the same time, most studies of the SEI apply ex situ characterization methods, which may introduce artifacts or misinterpretations as they do not investigate the SEI in its unaltered state immersed in liquid battery electrolyte. Thus, in this work, we focus on using the non-destructive combination of electrochemical quartz crystal microbalance with dissipation monitoring (EQCM-D) and impedance spectroscopy (EIS) in the same electrochemical cell. EQCM-D can not only probe the solidified products of the SEI but also allows for the monitoring of viscoelastic layers and viscosity changes of the electrolyte at the interphase during the SEI formation. EIS complements those results by providing electrochemical properties of the formed interphase. Our results highlight substantial differences in the physical and electrochemical properties between the SEI formed on copper and on amorphous carbon and show how formation parameters and the additive vinylene carbonate (VC) influence their growth. The EQCM-D results show consistently that much thicker SEIs are formed on carbon substrates in comparison to copper substrates. Full article

Two recombinant cutinases, AfCutA and AfCutB, derived from Aspergillus fumigatus, were heterologously expressed in Pichia pastoris and systematically characterized for their biochemical properties and polyester-degrading capabilities. AfCutA demonstrated superior catalytic performance compared with AfCutB, displaying higher optimal pH (8.0–9.0 vs. 7.0–8.0), higher optimal temperature (60 °C vs. 50 °C), and greater thermostability. AfCutA exhibited increased hydrolytic activity toward p-nitrophenyl esters (C4–C16) and synthetic polyesters. Additionally, AfCutA released approximately 3.2-fold more acetic acid from polyvinyl acetate (PVAc) hydrolysis than AfCutB. Quartz crystal microbalance with dissipation monitoring (QCM-D) revealed rapid adsorption of both enzymes onto polyester films. However, their adsorption capacity on poly (ε-caprolactone) (PCL) films was significantly higher than on polybutylene succinate (PBS) films, and was influenced by pH. Comparative modeling of catalytic domains identified distinct structural differences between the two cutinases. AfCutA possesses a shallower substrate-binding cleft, fewer acidic residues, and more extensive hydrophobic regions around the active site, potentially explaining its enhanced interfacial activation and catalytic efficiency toward synthetic polyester substrates. The notably superior performance of AfCutA suggests its potential as a biocatalyst in industrial applications, particularly in polyester waste bioremediation and sustainable polymer processing. Full article

Its crucial importance to the long-term operation of lithium-ion batteries has made the solid electrolyte interphase (SEI) the subject of intensive research efforts. These investigations are challenging, however, due to the very complex and fragile nature of this layer. With its typical thickness being in the range of some 10 nm and its chemical make-up being highly sensitive to even the smallest amounts of impurities, it becomes clear that artifacts are easily introduced in investigations of the SEI, especially if the measurements are performed ex situ. To help ameliorate these issues, we herein report a combination of non-destructive operando techniques that can be employed simultaneously in the same electrochemical cell to provide a plethora of physical, morphological, and electrochemical data on the macroscopic and microscopic scale. These techniques encompass atomic force microscopy (AFM), electrochemical quartz crystal microbalance with dissipation monitoring (EQCM-D), and impedance spectroscopy (EIS). This work focuses on how to combine these techniques in a single electrochemical cell, which is suitable to study SEI formation while avoiding noise, crosstalk, inhomogeneous SEI formation, and other pitfalls. Full article

By monitoring the solidification of droplets of plant latices with a fast quartz crystal microbalance with dissipation monitoring (QCM-D), droplets from Campanula glomerata were found to solidify much faster than droplets from Euphorbia characias and also faster than droplets from all technical latices tested. A similar conclusion was drawn from optical videos, where the plants were injured and the milky fluid was stretched (sometimes forming fibers) after the cut. Rapid solidification cannot be explained with physical drying because physical drying is transport-limited and therefore is inherently slow. It can, however, be explained with coagulation being triggered by a sudden decrease in hydrostatic pressure. A mechanism based on a pressure drop is corroborated by optical videos of both plants being injured under water. While the liquid exuded by E. characias keeps streaming away, the liquid exuded by C. glomerata quickly forms a plug even under water. Presumably, the pressure drop causes an influx of serum into the laticifers. The serum, in turn, triggers a transition from a liquid–liquid phase separated state (an LLPS state) of a resin and hardener to a single-phase state. QCM measurements, optical videos, and cryo-SEM images suggest that LLPS plays a role in the solidification of C. glomerata. Full article

Supported lipid bilayers (SLBs) that model neuronal membranes are needed to explore the role of membrane lipids in the misfolding and aggregation of amyloid proteins associated with neurodegenerative diseases, including Parkinson’s and Alzheimer’s disease. The neuronal membranes include not only phospholipids, but also significant amounts of cholesterol, sphingomyelin, and gangliosides, which are critical to its biological function. In this study, we explored the conditions for the formation of an SLB, for the five-component lipid mixture composed of zwitterionic 1,2-Dioleoyl-sn-glycero-3-phosphocholine (DOPC), anionic 1,2-dioleoyl- sn-glycero-3-phospho-L-serine (DOPS), nonionic cholesterol (Chol), zwitterionic sphingomyelin (SM), and anionic ganglioside (GM), using the quartz crystal microbalance with dissipation monitoring (QCM-D) technique, by varying experimental parameters such as pH, buffer type, temperature, vesicle size, and osmotic stress. SLB formation from this multicomponent lipid system was found challenging because the vesicles adsorbed intact on the quartz crystal and failed to rupture. For most of the variables tested, other than osmotic stress, we found no or only partial vesicle rupture leading to either a supported layer of vesicles or a partial SLB that included unruptured vesicles. When osmotic stress was applied to the vesicles already adsorbed on the surface, by having a different salt concentration in the rinse buffer that follows vesicle flow compared to that of the dilution buffer during vesicle flow and adsorption, vesicle rupture increased, but it remained incomplete. In contrast, when osmotic stress was applied during vesicle flow and adsorption on the surface, by having different salt concentrations in the dilution buffer in which vesicles flowed compared to the hydration buffer in which vesicles were prepared, complete vesicle rupture and successful formation of a rigid SLB was demonstrated. The robustness of this approach to form SLBs by applying osmotic stress during vesicle adsorption was found to be independent of the number of lipid components, as shown by SLB formation from the 1-, 2-, 3-, 4-, and 5-component lipid systems. Full article

This study examines the adsorption and bulk assembly behaviour of quaternized hydroxyethylcellulose ethoxylate (QHECE)–sodium dodecyl sulphate (SDS) complexes on negatively charged substrates. Due to its quaternized structure, QHECE, which is used in several industries, including cosmetics, exhibits enhanced electrostatic interactions. The phase behaviour and adsorption mechanisms of QHECE–SDS complexes are investigated using model substrates that mimic the wettability and surface charge of damaged hair fibres. Two preparation methodologies, high-concentration mixing and gradient-free mixing, were employed to examine their impact on the complex equilibrium, phase behaviour, and adsorption properties of the complexes. The measurements of turbidity, electrophoretic mobility, and conductivity demonstrate the existence of nonequilibrium dynamics during the mixing process, which exert a significant influence on the structural and functional characteristics of the complexes. The quartz crystal microbalance with dissipation monitoring (QCM-D) was employed to investigate the adsorption of the complexes onto the substrates. The results demonstrated the critical role of intermediate SDS concentrations in enhancing deposition. The findings emphasise the importance of formulation and preparation protocols in designing stable, high-performance cosmetic products. This research advances our understanding of polyelectrolyte–surfactant interactions and provides insights into optimising QHECE-based formulations. Full article