Search Results (824)

The complex system of high-entropy materials makes it challenging to reveal the specific function of each site for oxygen evolution reaction (OER). Here, with nickel foam (NF) as the substrate, FeCoNiCrMo/NF is designed to be prepared by metal–organic frameworks (MOF) as a precursor under an argon atmosphere. XRD analysis confirms that it retains a partial MOF crystal structure (characteristic peak at 2θ = 11.8°) with amorphous carbon (peaks at 22° and 48°). SEM-EDS mapping and XPS demonstrate uniform distribution of Fe, Co, Ni, Cr, and Mo with a molar ratio of 27:24:30:11:9. Electrochemical test results show that FeCoNiCrMo/NF has excellent OER characteristics compared with other reference prepared samples. FeCoNiCrMo/NF has an overpotential of 285 mV at 100 mA cm⁻² and performs continuously for 100 h without significant decline. The OER mechanism of FeCoNiCrMo/NF further reveal that Co and Ni are true active sites, and the dissolution of Cr and Mo promote the conversion of active sites into MOOH following the lattice oxygen mechanism (LOM). The precipitation–dissolution equilibrium of Fe also plays an important role in the OER process. The study of different reaction sites in complex systems points the way to designing efficient and robust catalysts. Full article

Industrial catalysts are accelerating the global transition toward renewable energy, serving as enablers for innovative technologies that enhance efficiency, lower costs, and improve environmental sustainability. This review explores the pivotal roles of industrial catalysts in hydrogen production, biofuel generation, and biomass conversion, highlighting their transformative impact on renewable energy systems. Precious-metal-based electrocatalysts such as ruthenium (Ru), iridium (Ir), and platinum (Pt) demonstrate high efficiency but face challenges due to their cost and stability. Alternatives like nickel-cobalt oxide (NiCo₂O₄) and Ti₃C₂ MXene materials show promise in addressing these limitations, enabling cost-effective and scalable hydrogen production. Additionally, nickel-based catalysts supported on alumina optimize SMR, reducing coke formation and improving efficiency. In biofuel production, heterogeneous catalysts play a crucial role in converting biomass into valuable fuels. Co-based bimetallic catalysts enhance hydrodeoxygenation (HDO) processes, improving the yield of biofuels like dimethylfuran (DMF) and γ-valerolactone (GVL). Innovative materials such as biochar, red mud, and metal–organic frameworks (MOFs) facilitate sustainable waste-to-fuel conversion and biodiesel production, offering environmental and economic benefits. Power-to-X technologies, which convert renewable electricity into chemical energy carriers like hydrogen and synthetic fuels, rely on advanced catalysts to improve reaction rates, selectivity, and energy efficiency. Innovations in non-precious metal catalysts, nanostructured materials, and defect-engineered catalysts provide solutions for sustainable energy systems. These advancements promise to enhance efficiency, reduce environmental footprints, and ensure the viability of renewable energy technologies. Full article

The precise synthesis of non-precious metal single-atom electrocatalysts is crucial for enhancing the yield of highly active reactive oxygen species (ROSs). Conventional oxidation methods, such as Fenton or NaClO processes, suffer from poor efficiency, high energy demand, and secondary pollution. In contrast, heterogeneous electro-Fenton systems based on cascade oxygen reduction reactions (ORRs), which require low operational voltage and cause pollutant degradation through both direct electron transfer and ROS generation, have emerged as a promising alternative. Recent studies showed that carbon cathodes decorated with atomically dispersed transition metals can effectively integrate the excellent conductivity of carbon supports with the tunable surface chemistry of metal centers. However, the electronic structure of active sites intrinsically hinders the simultaneous achievement of high activity and selectivity in cascade ORRs. This review summarizes the advances, specifically from 2020 to 2025, in understanding the mechanism of cascade ORRs and the synthesis of transition metal-based single-atom catalysts in cathode electrocatalysis for efficient wastewater treatment, and discusses the key factors affecting treatment performance. While employing atomically engineered cathodes is a promising approach for energy-efficient wastewater treatment, future efforts should overcome the barriers in active site control and long-term stability of the catalysts to fully exploit their potential in addressing water pollution challenges. Full article

The usage of fossil fuels has resulted in increasingly severe environmental problems, such as climate change, air pollution, water pollution, etc. Hydrogen energy is considered one of the most promising clean energies to replace fossil fuels due to its pollution-free and high-heat properties. However, the oxygen evolution reaction (OER) remains a critical challenge due to its high overpotential and slow kinetics during water electrolysis for hydrogen production. Electrocatalysts play an important role in lowering the overpotential of OER and promoting the kinetics. Co₃O₄-based electrocatalysts have emerged as promising candidates for the oxygen evolution reaction (OER) due to their favorable catalytic activity and good compatibility compared with precious metal-based electrocatalysts. This review presents a summary of the recent developments in the synthesis strategies and mechanisms of Co₃O₄-based electrocatalysts for the OER. Various synthesis strategies have been explored to control the size, morphology, and composition of Co₃O₄ nanoparticles. These strategies enable the fabrication of well-defined nanostructures with enhanced catalytic performance. Additionally, the mechanisms of OER catalysis on Co₃O₄-based electrocatalysts have been elucidated. Coordinatively unsaturated sites, synergistic effects with other elements, surface restructuring, and pH dependency have been identified as crucial factors influencing the catalytic activity. The understanding of these mechanisms provides insights into the design and optimization of Co₃O₄-based electrocatalysts for efficient OER applications. The recent advancements discussed in this review offer valuable perspectives for researchers working on the development of electrocatalysts for the OER, with the goal of achieving sustainable and efficient energy conversion and storage systems. Full article

The Jinbaoshan Pt-Pd deposit is China’s largest independent PGM deposit. However, the deposit has not been utilized until now because of the low grade of precious metals, the complex mineral composition, and, notably, the presence of precious metals in the microgranular material disseminated to other minerals. Its high MgO content, in particular, is regarded as a challenge for efficiently recovering precious metals via mature pyrometallurgical methods. In this research, the feasibility of a smelting process to recover precious metals from Jinbaoshan Pt-Pd concentrates at a conventional smelting temperature (1350 °C) with the addition of iron ore as a metal collector and SiO₂ and CaO as fluxes was verified on the basis of thermodynamic slag design and experimental analyses. Under the optimal conditions of 100 g of the Pt-Pd concentrates, 32.5 g of SiO₂, 7.5 g of CaO, and 30 g of iron ore at 1350 °C for 1 h, the extraction efficiencies of Au, Pt, and Pd were 94.66%, 96.75%, and 97.28%, respectively. This strategy enables the rapid collection of PGMs from Jinbaoshan Pt-Pd concentrates at the conventional temperature within a short time and minimizes the use of fluxes and collectors, contributing to energy and cost conservation. Full article

In recent years, recovering precious and base metals such as silver and copper from end-of-life products has become a fundamental factor in the sustainable development of many countries. This not only supports environmental goals but is also a profitable economic activity. Therefore, in this study, we investigate the recovery of silver and copper from an end-of-life photovoltaic panel powder using an alternative leaching system containing sulfuric acid and ferric sulfate instead of nitric acid-based leaching systems, which are susceptible to producing hazardous gases such as NO_x. To obtain this goal, a series of experiments were designed with the Central Composite Design (CCD) approach using Response Surface Methodology (RSM) to evaluate the effect of reagent concentrations on the leaching rate. The leaching results showed that high recovery rates of silver (>85%) and copper (>96%) were achieved at room temperature using a solution containing only 0.2 M sulfuric acid and 0.15 M ferric sulfate. Analysis of variance was applied to the leaching data for silver and copper recovery, resulting in two statistical models that predict the leaching efficiency based on reagent concentrations. Results indicate that the models are statistically significant due to their high R² (0.9988 and 0.9911 for Ag and Cu, respectively) and the low p-value of 0.0043 and 0.0003 for Ag and Cu, respectively. The models were optimized to maximize the dissolution of silver and copper using Design Expert software. Full article

Hydrogen energy is a pivotal carrier for achieving carbon neutrality, requiring green and efficient production via water electrolysis. However, the anodic oxygen evolution reaction (OER) involves a sluggish four-electron transfer process, resulting in high overpotentials, while the prohibitive cost and complex preparation of precious metal catalysts impede large-scale commercialization. In this study, we develop a FeCo-based bimetallic deep eutectic solvent (FeCo-DES) as a multifunctional reaction medium for engineering a three-dimensional (3D) coral-like FeOOH-Co₂(OH)₃Cl/NF composite via a mild one-step impregnation approach (70 °C, ambient pressure). The FeCo-DES simultaneously serves as the solvent, metal source, and redox agent, driving the controlled in situ assembly of FeOOH-Co₂(OH)₃Cl hybrids on Ni(OH)₂/NiOOH-coated nickel foam (NF). This hierarchical architecture induces synergistic enhancement through geometric structural effects combined with multi-component electronic interactions. Consequently, the FeOOH-Co₂(OH)₃Cl/NF catalyst achieves a remarkably low overpotential of 197 mV at 100 mA cm⁻² and a Tafel slope of 65.9 mV dec⁻¹, along with 98% current retention over 24 h chronopotentiometry. This study pioneers a DES-mediated strategy for designing robust composite catalysts, establishing a scalable blueprint for high-performance and low-cost OER systems. Full article

This review examines the research progress on non-noble-metal-based catalysts for formaldehyde (HCHO) oxidation at room temperature. It begins with an introduction to the hazards of HCHO as an indoor pollutant and the urgency of its removal, comparing several HCHO removal technologies and highlighting the advantages of room-temperature catalytic oxidation. It delves into the classification, preparation methods, and regulation strategies for non-precious metal catalysts, with a focus on manganese-based, cobalt-based, and other transition metal-based catalysts. The effects of catalyst preparation methods, morphological structure, and specific surface area on catalytic performance are discussed, and the catalytic oxidation mechanisms of HCHO, including the Eley–Rideal, Langmuir–Hinshelwood, and Mars–van Krevelen mechanisms, are analyzed. Finally, the challenges faced by non-precious metal catalysts are summarized, such as issues related to the powder form of catalysts in practical applications, lower catalytic activity at room temperature, and insufficient research in the presence of multiple VOC molecules. Suggestions for future research directions are also provided. Full article

Estuaries are excellent containers for the prehistorical and historical pollution that develops in their river basins. This paper studies the Au contents obtained by inductively coupled plasma spectrometry of two cores extracted from the Doñana National Park (Guadalquivir Estuary, SW Spain). Concentrations of this precious metal have been associated with the different prehistoric and historical stages of exploitation of the Iberian Pyritic Belt. The three detected peaks correspond to the first mining operations in the area around the park, the first systematic Tartessian mining and strong exploitation during the Roman period. Consequently, Au is an appropriate marker of the contamination phases prior to its current extraordinary biological diversity. Full article

The oxygen evolution reaction (OER) plays a central role as an anode in electrocatalytic processes such as energy conversion and storage and the generation of molecular oxygen from the electrolysis of water. Currently, precious metal oxides such as IrO₂ and RuO₂ are recognized as reference OER electrocatalysts with reasonably high activity; however, their widespread use in practical devices has been severely hindered by their high cost and scarcity. It is essential to design alternative OER electrocatalysts made of low-cost and abundant earth elements with significant activity and robustness. We report four new nanocellulose-derived Fe–zeolite nanocomposites, namely Fe/Zeolite@CCNC (1), Fe/Zeolite@CCNF (2), Fe/Zeolite/CNT@CCNC (3), and Fe/Zeolite/CNT@CCNF (4). Two different types of nanocellulose were investigated: nanocellulose nanofibrils and nanocellulose nanocrystals. Characterization with TEM, SEM-EDS, PXRD, and XPS is reported. The nanocomposites exhibited electrocatalytic activity for OER that varies based on the origin of biocarbon and the composition content. The effect of adding carbon nanotubes to the nanocomposites was studied, and an improvement in OER catalysis was observed. The electrochemical double-layer capacitance and electrochemical impedance spectroscopy of the nanocomposites are reported. The nanocomposite 3 exhibited the highest performance, with an onset potential value of 1.654 V and an overpotential of 551 mV, which exceeds the activity of RuO₂ for OER catalysis at 10 mA/cm² in the glassy carbon electrode. A 24 h chronoamperometry study revealed that the catalyst is active for ~2 h under continuous operating conditions. BET surface analysis showed that the crystalline nanocellulose-derived composite exhibited 301.47 m²/g, and the fibril nanocellulose-derived composite exhibited 120.39 m²/g, indicating that the increased nanoporosity of the former contributes to the increase in OER catalysis. Full article

The present article aims to develop a technological scheme for processing zinc ferrite residue, which typically forms during the leaching of zinc calcine. This semi-product is currently processed through the Waelz process, the main disadvantage of which is the loss of precious metals with the Waelz clinker. The experimental results of numerous experiments and analyses have verified a technological scheme including the following operations: sulfuric acid leaching of zinc ferrite residue under atmospheric conditions; autoclave purification of the resulting productive solution to obtain hematite; chloride leaching of lead and silver from the insoluble residue, which was produced in the initial operation; and cementation with zinc powder of lead and silver from the chloride solution. Utilizing such an advanced methodology, the degree of zinc leaching is 98.30% at a sulfuric acid concentration of 200 g/L, with a solid-to-liquid ratio of 1:10 and a temperature of 90 °C. Under these conditions, 96.40% Cu and 92.72% Fe form a solution. Trivalent iron in the presence of seeds at a temperature of 200 °C precipitates as hematite. In chloride extraction with 250 g/L NaCl, 1 M HCl, and a temperature of 60 °C, the leaching degree of lead is 96.79%, while that of silver is 84.55%. In the process of cementation with zinc powder, the degree of extraction of lead and silver in the cement precipitate is 98.72% and 97.27%, respectively. When implementing this scheme, approximately 15% of the insoluble residue remains, containing 1.6% Pb and 0.016% Ag. Full article

Cisplatin was the first metal-based anticancer drug introduced into clinical use. It is a “small” molecule, but it represented a very “big” discovery. Since it was introduced on the market, it has not been withdrawn, despite being not free of side effects, owing to its peculiarity of being highly effective in the treatment of cancer. Anticancer activity of the platinum-based complexes was discovered with this molecule; since then, several other platinum-based drugs have been developed and tested in preclinical studies against cancer cells; however, only a few of them reached clinical trials, and their side effects are not much less than cisplatin. Despite the constraints of drug resistance and side effects, chemotherapy remains a fundamental strategy in cancer treatment. Nowadays, cisplatin remains one of the most-used anticancer agents in treating lung, colon, ovary, testicles, bladder, cervix, and many more cancers, although cisplatin resistance represents a major hurdle in cancer treatment. Will there ever be another drug that can overcome the side effects of cisplatin but at the same time be able to block tumors as does cisplatin? Full article

Selective catalytic reduction filter (SDPF) technology constitutes a critical methodology for controlling nitrogen oxide (NOx) and particulate matter emissions from light-duty diesel vehicles. A series of SDPFs with different sulfur poisoning times and concentrations were prepared using the worldwide harmonized light vehicles test cycle (WLTC). Bench testing revealed that sulfur poisoning diminished the catalyst’s NH₃ storage capacity, impaired the transient NOx reduction efficiency, and induced premature ammonia leakage. After multiple sulfur poisoning incidents, the NOx reduction performance stabilized. Higher SO₂ concentrations accelerated catalyst deactivation and hastened the attainment of this equilibrium state. The characterization results for the catalyst indicate that the catalyst accumulated the same sulfur content after tail gas poisoning with different sulfur concentrations and that sulfur existed in the form of SO₄²⁻. The sulfur species in low-sulfur-poisoning-concentration catalysts mainly included sulfur ammonia and sulfur copper species, while high-sulfur-poisoning-concentration catalysts contained a higher proportion of sulfur copper species. Neither species type significantly altered the zeolite coating’s crystalline structure. Sulfur ammonia species could easily lead to a significant decrease in the specific surface area of the catalyst, which could be decomposed at 500 °C to achieve NOx reduction performance regeneration. In contrast, sulfur copper species required higher decomposition temperatures (600 °C), achieving only partial regeneration. Full article

Anion exchange membranes (AEMs) are vital for electrochemical energy devices such as alkaline fuel cells and water electrolyzers, enabling the use of non-precious metal catalysts despite challenges from alkaline degradation. Hyperbranched polymers (hbPs) with their globular structure, high functional group density, and simple synthesis, offer a promising platform for enhancing transport and stability. In this study, multifunctional hbPs were synthesized from 4-vinylbenzyl chloride (VBC) and 2-hydroxyethyl methacrylate (HEMA) via atom transfer radical self-condensing vinyl polymerization (ATR-SCVP) and crosslinked into polyurethane-based AEMs. Characterization confirmed successful copolymerization and crosslinking, with excellent alkaline stability. Membranes crosslinked with higher molecular weight (MW) and VBC-richer hbPs (e.g., OH-hbP1-PU) exhibited high water uptake (75%) but low ion-exchange capacity (1.54 mmol/g) and conductivity (186 µS/cm), attributed to steric hindrance and insufficient ionic network connectivity. In contrast, OH-hbP2-PU exhibited optimal properties, with the highest OH⁻ conductivity (338 µS/cm) and IEC (2.64 mmol/g), highlighting a balanced structure for efficient ion transport. This work offers a tunable strategy for high-performance AEM development through tailored hbP architecture. Full article