Search Results (146)

This study presents a microfluidic chip platform designed using a multiscale 3D printing strategy for fabricating microfluidic chips with integrated, high-resolution, and customizable membrane structures. By combining two-photon polymerization (2PP) for submicron membrane fabrication with liquid crystal display printing for rapid production of larger components, this approach addresses key challenges in membrane integration, including sealing reliability and the use of transparent materials. Compared to fully 2PP-based fabrication, the multiscale method achieved a 56-fold reduction in production time, reducing total fabrication time to approximately 7.2 h per chip and offering a highly efficient solution for integrating complex structures into fluidic chips. The fabricated chips demonstrated excellent mechanical integrity. Burst pressure testing showed that all samples withstood internal pressures averaging 1.27 ± 0.099 MPa, with some reaching up to 1.4 MPa. Flow testing from ~35 $\mathsf{\mu }$L/min to ~345 $\mathsf{\mu }$L/min confirmed stable operation in 75 $\mathsf{\mu }$m square channels, with no leakage and minimal flow resistance up to ~175 $\mathsf{\mu }$L/min without deviation from the predicted behavior in the 75 $\mathsf{\mu }$m. Membrane-integrated chips exhibited outlet flow asymmetries greater than 10%, indicating active fluid transfer across the membrane and highlighting flow-dependent permeability. Overall, this multiscale 3D printing approach offers a scalable and versatile solution for microfluidic device manufacturing. The method’s ability to integrate precise membrane structures enable advanced functionalities such as diffusion-driven particle sorting and molecular filtration, supporting a wide range of biomedical, environmental, and industrial lab-on-a-chip applications. Full article

Measuring pH is a critical parameter in environmental monitoring, biomedical diagnostics, food safety, and industrial processes. Optical fiber sensors have proven highly effective for pH detection due to their exceptional sensitivity, rapid response, and resistance to electromagnetic interference, making them well suited for real-time monitoring. This review offers a comprehensive analysis of recent advances in optical fiber-based pH sensors, covering key techniques such as fluorescence-based, absorbance-based, evanescent wave, and interferometric methods. Innovations in Fiber Bragg Grating and Surface Plasmon Resonance technologies are also examined. The discussion extends to the impact of pH-sensitive coatings—ranging from nanomaterials and polymeric films to graphene-based compounds—on enhancing sensor performance. Recent advancements have also enabled automation in data analysis and improvements in remote sensing capabilities. The review further compares the economic viability of optical fiber sensors with traditional electrochemical methods, while acknowledging persistent issues such as temperature cross-sensitivity, long-term stability, and fabrication costs. Overall, recent developments have broadened the functionality and application scope of these sensors by improving efficiency, accuracy, and scalability. Future research directions are outlined, including advanced optical interrogation techniques, such as Addressed Fiber Bragg Structures (AFBSs), microwave photonic integration, and optimized material selection. These approaches aim to enhance performance, reduce costs, and enable the broader adoption of optical fiber pH sensors. Full article

As three-dimensional (3D) printing becomes increasingly prevalent in microfluidic system fabrication, the demand for high precision has become critical. Among various 3D printing technologies, light-curing-based methods offer superior resolution and are particularly well suited for fabricating microfluidic channels and associated micron-scale components. Two-photon polymerization (TPP), one such method, can achieve ultra-high resolution at the submicron level. However, its severely limited printable volume and high operational costs significantly constrain its practicality for real-world applications. In contrast, digital light processing (DLP) 3D printing provides a more balanced alternative, offering operational convenience, lower cost, and print dimensions that are more compatible with practical microfluidic needs. Despite these advantages, most commercial DLP systems still struggle to fabricate intricate, high-resolution structures—particularly curve, thin-walled, or hollow ones—due to over-curing and interlayer adhesion issues. In this study, we developed a DLP-based projection micro-stereolithography (PμSL) system with a simple optical reconfiguration and fine-tuned its parameters to overcome limitations in printing precise and intricate structures. For demonstration, we selected an Archimedes microscrew as the target structure, as it serves as a key component in microfluidic micromixers. Based on our previous study, the most effective design was selected and fabricated in accordance with practical microfluidic dimensions. The PμSL system developed in this study, along with optimized parameters, provides a reference for applying DLP 3D printing in high-precision microfabrication and advancing microfluidic component development. Full article

The rapid evolution of optoelectronic devices necessitates innovative fabrication techniques to improve their performance and functionality. This review explores the advancements in laser processing as a versatile method for creating micro- and nanostructured surfaces, tailored to enhance the efficiency of optoelectronic applications. We begin by elucidating the fundamental mechanisms underlying laser interactions with materials, which facilitate the precise engineering of surface topographies. Following this, we systematically review various micro/nanostructures fabricated by laser techniques, such as laser ablation, laser-induced periodic surface structures (LIPSS), and two-photon polymerization, highlighting their unique properties and fabrication parameters. The review also delves into the significant applications of these laser-fabricated surfaces in optoelectronic devices, including photovoltaics, photodetectors, and sensors, emphasizing how tailored surface structures can lead to improved light absorption, enhanced charge carrier dynamics, and optimized device performance. By synthesizing current knowledge and identifying emerging trends, this work aims to inspire future research directions in the design and application of laser-fabricated micro/nanostructures within the field of optoelectronics. Our findings underscore the critical role of laser technology in advancing the capabilities of next-generation optoelectronic devices, aligning with the scope of emerging trends in device engineering. Full article

The optical and radiation shielding of PVA have been enhanced through embedding with ZnO/CuO/SWCNT (ZCS) nanocomposites. ZCS polymeric nanocomposites (PNCs) were prepared with the solution casting method. Scanning electron, optical microscopy and FT-IR procedures were performed to examine the surfaces’ morphology and structures’ modifications. UV–visible measurements were carried out to investigate the linear/nonlinear optical properties. The optical investigations show significant alterations in the optical parameters of PVA due to ZCS embedding. The UV–visible analysis shows that the optical parameters, including the transmittance, energy bandgap, refractive index, dielectric constants and optical conductivity of PVA, are tuned through ZCS embedding. The direct and indirect bandgap of PVA shrank from 5.42 eV and 4.99 eV (neat PVA) to 3.20 eV and 2.26 eV (10 wt.% ZCS PNCs). The nonlinear optical (NLO) constants (first order susceptibility (χ⁽¹⁾), third susceptibility (χ⁽³⁾) and refractive index (n₂)) of PVA were improved. Phy-X/PSD software was used to investigate the radiation shielding parameters of all samples. The linear attenuation coefficient (LAC), mean free path (MFP), half value layer (HVL), tenth value layer (TVL) and effective atomic number (Z_eff) of PVA were enhanced through ZCS embedding. It is found that the mass attenuation coefficient (MAC) of the neat PVA increased from 1.14 cm²/g to 7.96 cm²/g at 0.015 MeV. The HVL of PVA decreased from 30.2 cm to 20.6 cm, the TVL decreased from 100.3 cm to 68.5 cm and the MFP decreased from 43.6 cm to 29.8 cm upon embedding 10 wt.% of ZCS NCs at 15 MeV. The samples’ exposure buildup factor (EBF) and energy absorption buildup factor (EABF) in the photon energy range from 0.015 MeV to 15 MeV at 0.5 to 40 MFP values. This study proves that ZCS PNCs are advantageous for applications in optical and radiation shielding fields. Full article

This work demonstrates the fabrication of microstructures with formulations containing bio-based prepolymers derived from itaconic acid, commercial reactive diluents, photo initiators, and inhibitors, through two-photon polymerization. Lateral and vertical resolutions within the micron range can be achieved by the adjustment of laser scanning speed and pulse energy, and through the use of microscope objectives with high magnification and numerical aperture. The fabrication throughput can be slightly increased by simultaneously increasing the laser pulse energy and scanning speed, with special care to keep the resolution of the features that can be written via two-photon polymerization. Feasibility for the fabrication of 3D microstructures is demonstrated, through the fabrication of benchmark structures like woodpiles and pyramidal structures. Thus, this work proves that resins based on biobased formulations, originally designed for UV-curing 3D printing, can be adapted for two-photon polymerization, obtaining 3D microstructures with resolutions within the micron range. Full article

Recent developments in the synthesis of substituted polyacetylenes have considerably benefitted from advancements in organometallic catalysis; however, most important developments rely on the advent of Rh-catalyzed living polymerizations. The latter not only allow the tailoring of well-defined degrees of polymerization with low and narrow polydispersity but also enable access to stereochemical well-defined cis-transoidal polymers with a helical structure. These novel polymers open new avenues for application in photonics and electronics. Rh-catalyzed living polymerizations are mild and concise metal-catalyzed polymer syntheses that not only allow for the decoration of sidechains with multiple functionalities, including chiral units, but also enable enantioselective induction of helical chirality, memory of chirality, well-defined copolymerization, and end-group functionalization at both termini. This review summarizes recent developments in metal-catalyzed syntheses of substituted polyacetylenes, with a special focus on Rh-catalyzed living polymerizations. Full article

In this work, we investigated the influence of the synthetic conditions of core/shell particles on physico–chemical properties of their shells, the process of self-assembly of particles into 3D-ordered structures, and the sensitivity of films based on these particles to the presence of ethanol and temperature changes. The core/shell particles were prepared by two methods: seed emulsion copolymerization and semi-batch emulsion copolymerization. The cores consisted of polystyrene or its copolymer with methyl methacrylate. Polymer shells of the particles were obtained by copolymerization of methyl methacrylate with several acrylate comonomers: butyl acrylate, butyl methacrylate, propyl acrylate, and ethyl acrylate. The photonic crystal films with the highest sensitivity to ethanol vapors were obtained on the basis of the core/shell particles synthesized by semi-batch emulsion polymerization. It was also established that introducing butyl acrylate or propyl acrylate units into shell copolymers led to an increase in the sensitivity of the resulting photonic crystal films. The films demonstrated a pronounced thermosensitivity only when the corresponding core/shell particles were synthesized as follows: the shell comonomers (methyl methacrylate and butyl acrylate) were introduced into the reaction system during the semi-batch emulsion process in a single step. The intensity of the photonic band gap (PBG) peak for these films decreased by 100% at around 42 °C. Full article

Currently, tissue engineering technologies are promising for the restoration of damaged organs and tissues. For regeneration of electrically conductive tissues or neural interfaces, it is necessary to provide electrical conductivity for the transmission of electrophysiological signals. The developed biocomposite structures presented in this article possess such properties. Their composition includes bovine serum albumin (BSA), gelatin, eosin-Y and single-walled carbon nanotubes (SWCNTs). For the first time, a biocomposite structure was formed from the proposed hydrogel using a nanosecond laser, and a two-photon absorption cross section value of 580 GM was achieved. Increased viscosity over 3 mPa∙s and self-focusing with a nonlinear refractive index of 42 × 10⁻¹² cm²/W make it possible to create a biocomposite structure over the entire specified area. The obtained electrical conductivity value was 19 mS∙cm⁻¹, due to the formation of effective electrically conductive networks. For a biocomposite with a concentration of gelatin 3 wt. %, formed by low-energy near-IR pulses, the survival of Neuro 2A nerve tissue cells was confirmed. The obtained results are important for the creation of new tissue engineering structures and neural interfaces from a biopolymer hydrogel based on the organic dye eosin-Y and carbon nanotubes by two-photon polymerization. Full article

Femtosecond laser two-photon polymerization (TPP) technology, known for its high precision and its ability to fabricate arbitrary 3D structures, has been widely applied in the production of various micro/nano optical devices, achieving significant advancements, particularly in the field of photonic wire bonding (PWB) for optical interconnects. Currently, research on optimizing both the optical loss and production reliability of polymeric photonic wires is still in its early stages. One of the key challenges is that inadequate metrology methods cannot meet the demand for multiphysical measurements in practical scenarios. This study utilizes novel in situ scanning electron microscopy (SEM) to monitor the working PWBs fabricated by TPP technology at the microscale. Optical and mechanical measurements are made simultaneously to evaluate the production qualities and to study the multiphysical coupling effects of PWBs. The results reveal that photonic wires with larger local curvature radii are more prone to plastic failure, while those with smaller local curvature radii recover elastically. Furthermore, larger cross-sectional dimensions contribute dominantly to the improved mechanical robustness. The optical-loss deterioration of the elastically deformed photonic wire is only temporary, and can be fully recovered when the load is removed. After further optimization based on the results of multiphysical metrology, the PWBs fabricated in this work achieve a minimum insertion loss of 0.6 dB. In this study, the multiphysical analysis of PWBs carried out by in situ SEM metrology offers a novel perspective for optimizing the design and performance of microscale polymeric waveguides, which could potentially promote the mass production reliability of TPP technology in the field of chip-level optical interconnection. Full article

Three-dimensional cancer cell cultures have been a valuable research model for developing new drug targets in the preclinical stage. However, there are still limitations to these in vitro models. Scaffold-based systems offer a promising approach to overcoming these challenges in cancer research. In this study, we show that two-photon polymerization (TPP)-assisted printing of scaffolds enhances 3D tumor cell culture formation without additional modifications. TPP is a perfect fit for this task, as it is an advanced 3D-printing technique combining a μm-level resolution with complete freedom in the design of the final structure. Additionally, it can use a wide array of materials, including biocompatible ones. We exploit these capabilities to fabricate scaffolds from two different biocompatible materials—PEGDA and OrmoClear. Cubic spheroid scaffolds with a more complex architecture were produced and tested. The biological evaluation showed that the human ovarian cancer cell lines SKOV3 and A2780 formed 3D cultures on printed scaffolds without a preference for the material. The gene expression evaluation showed that the A2780 cell line exhibited substantial changes in CDH1, CDH2, TWIST, COL1A1, and SMAD3 gene expression, while the SKOV3 cell line had slight changes in said gene expression. Our findings show how the scaffold architecture design impacts tumor cell culture 3D spheroid formation, especially for the A2780 cancer cell line. Full article

A comprehensive study was performed on the supramolecular ordering and optical properties of thin nanostructured glycerohydrogel sol-gel plates based on chitosan L- and D-aspartate and their individual components in the X-ray, UV, visible, and IR ranges. Our comparative analysis of chiroptical characteristics, optical collimated transmittance, the average cosine of the scattering angle, microrelief and surface asymmetry, and the level of structuring shows a significant influence of the wavelength range of electromagnetic radiation and the enantiomeric form of aspartic acid on the functional characteristics of the sol-gel materials. At the macrolevel of the supramolecular organization, a complex topography of the surface layer and a dense amorphous–crystalline ordering of polymeric substances were revealed, while at the nanolevel, there were two forms of voluminous scattering domains: nanospheres with diameters of 60–120 nm (L-) and 45–55 nm (D-), anisometric particles of lengths within ~100–160 (L-) and ~85–125 nm (D-), and widths within ~10–20 (L-) and ~20–30 nm (D-). The effect of optical clearing on glass coated with a thin layer of chitosan L-(D-)aspartate in the near-UV region was discovered (observed for the first time for chitosan-based materials). The resulting nanocomposite shape-stable glycerohydrogels seem promising for sensorics and photonics. Full article

Magnetic soft microrobots have a wide range of applications in targeted drug therapy, cell manipulation, and other aspects. Currently, the research on magnetic soft microrobots is still in the exploratory stage, and most of the research focuses on a single helical structure, which has limited space to perform drug-carrying tasks efficiently and cannot satisfy specific medical goals in terms of propulsion speed. Therefore, balancing the motion speed and drug-carrying performance is a current challenge to overcome. In this paper, a magnetically controlled cone-helix soft microrobot structure with a drug-carrying function is proposed, its helical propulsion mechanism is deduced, a dynamical model is constructed, and the microrobot structure is prepared using femtosecond laser two-photon polymerization three-dimensional printing technology for magnetic drive control experiments. The results show that under the premise of ensuring sufficient drug-carrying space, the microrobot structure proposed in this paper can realize helical propulsion quickly and stably, and the speed of motion increases with increases in the frequency of the rotating magnetic field. The microrobot with a larger cavity diameter and a larger helical pitch exhibits faster rotary advancement speed, while the microrobot with a smaller helical height and a smaller helical cone angle outperforms other structures with the same feature sizes. The microrobot with a cone angle of 0.2 rad, a helical pitch of 100 µm, a helical height of 220 µm, and a cavity diameter of 80 µm achieves a maximum longitudinal motion speed of 390 µm/s. Full article

This research focuses on developing a 2D thin film comprising a monolayer of silica nanoparticles functionalized with polyethyleneimine (PEI), achieved through a novel integration of Langmuir–Blodgett (L-B) and Pickering emulsion techniques. The primary aim was to create a nanostructured film that exhibits dual functionality: iridescence and efficient metal ion adsorption, specifically Cu(II) ions. The methodology combined L-B and Pickering emulsion polymerization to assemble and stabilize a nanoparticle monolayer at an oil/water interface, which was then polymerized under UV radiation to form an asymmetrically structured film. The results demonstrate that the film possesses a high adsorption efficiency for Cu(II) ions, with the enhanced mechanical durability provided by a reinforcing layer of polyvinyl alcohol/glycerol. The advantage of combining L-B and Pickering emulsion technology is the ability to generate 2D films from functional nanoparticle monolayers that are sufficiently sturdy to be deployed in applications. The 2D film’s practical applications in environmental remediation were confirmed through its ability to adsorb and recover Cu(II) ions from aqueous solutions effectively. We thus demonstrate the film’s potential as a versatile tool in water treatment applications owing to its combined photonic and adsorptive properties. This work paves the way for future research on the use of nanoengineered films in environmental and possibly photonic applications focusing on enhancing the film’s structural robustness and exploring its broader applicability to other pollutants and metal ions. Full article

Soft optomechanical sensors have the ability to combine the high tunability and elasticity of soft polymers with the distinctive optical properties of photonic structures, thus offering unprecedented opportunities for the development high-performance colorimetric sensors. Herein, we demonstrate for the first time the use of optomechanical devices made of off-stoichiometry thiol-ene (OSTE), a polymeric material that features intrinsic redox activity, overcoming some limitations of conventional materials (e.g., polydimethylsiloxane or silicon). Remarkably, this work provides the foundation for a new generation of highly tunable and versatile optomechanical sensors, enabling unexplored functionalities. Full article