Search Results (216)

The practice in agriculture of spreading polyethylene (PE) film over the soil surface as mulch is a common, global practice that aids in conserving water, increasing crop yields, suppressing weed growth, and decreasing growing time. However, these films are typically only used for a single growing season, and thus, their use and non-biodegradability come with some serious environmental consequences due to their persistence in the soil and potential for microplastic pollution, particularly when retrieval and disposal options are poor. On the microscale, particles < 5 mm from degraded films have been observed to disrupt soil structure, impede water and nutrient cycling, and affect soil organisms and plant health. On the macroscale, there are obvious and serious environmental consequences associated with the burning of plastic film and its leakage from poorly managed landfills. To maintain the crop productivity afforded by mulching with PE film while avoiding the environmental downsides, the development and use of biodegradable polymer technologies is being explored. Here, the efficacy of a newly developed, water-dispersible, sprayable, and biodegradable polyester–urethane–urea (PEUU)-based polymer was compared with two commercial PE mulches, non-degradable polyethylene (NPE) and OPE (ox-degradable polyethylene), in a greenhouse tomato growth trial. Water savings and the effects on plant growth and soil characteristics were studied. It was found that PEUU provided similar water savings to the commercial PE-based mulches, up to 30–35%, while showing no deleterious effects on plant growth. The results should be taken as preliminary indications that the sprayable, biodegradable PEUU shows promise as a replacement for PE mulch, with further studies under outside field conditions warranted to assess its cost effectiveness in improving crop yields and, importantly, its longer-term impacts on soil and terrestrial fauna. Full article

Microplastic particles (MPs) are an emerging global pollutant of increasing concern due to their widespread occurrence, persistence, and multifaceted impact on aquatic ecosystems. This study provides a comprehensive review of peer-reviewed literature from 2011 to 2025, analysing the presence, distribution, and microbiological associations of MPs in surface waters across five continents. The findings confirm that MPs are present in both marine and freshwater systems, with concentrations varying by region, hydrology, and proximity to anthropogenic sources. Polyethylene and polypropylene were identified as the most common polymers, often enriched in river mouths, estuaries, and aquaculture zones. A key focus of this review is the plastisphere—microbial biofilms colonizing MPs—which includes both environmental and pathogenic bacteria such as Vibrio, Pseudomonas, and Acinetobacter. Notably, MPs serve as vectors for the spread of antibiotic resistance genes (ARGs), including sul1, tetA and ermF, and β-lactamase genes like blaCTX-M. This highlights their role in enhancing horizontal gene transfer and microbial dissemination. The results emphasize the need for standardized monitoring protocols and further interdisciplinary research. In light of the One Health approach, understanding the microbial dimension of MP pollution is essential for managing risks to environmental and public health. Full article

The pilot study is devoted to the assessment of both the accumulation and spatial distribution of microplastics in the snow cover of the Zhetysu region. The height of snow cover in the study area varied from 4.0 to 80.5 cm, with a volume of melt water ranging from 1.5 to 143 L. The analysis of 53 snow samples taken at different altitudes (from 350 to 1500 m above sea level) showed the presence of microplastics in 92.6% of samples in concentrations from 1 to 12 particles per square meter. In total, 170 microplastic particles were identified. The main polymers identified by Raman spectroscopy were polyethylene (PE), polypropylene (PP), and polystyrene (PS). These are typical components of plastic waste. The spatial distribution of microplastics showed elevated concentrations near settlements and roads. Notable contaminations were also recorded in remote mountainous areas, confirming the significant role of long-range atmospheric transport. Particles smaller than 0.5 mm dominated, having high aerodynamic mobility and capable of long-range atmospheric transport. Quantitative and qualitative characteristics of microplastics in snow cover have been realized for the first time both in Kazakhstan and in the Central Asian region, which contributes to the formation of primary ideas and future approaches about microplastic pollution in continental inland regions. The obtained results demonstrate the importance of atmospheric transport in the distribution of microplastics. They indicate the need for further monitoring and microplastic pollution analyses in Central Asia, taking into account its detection even in hard-to-reach and remote areas. Full article

In the environment, plastic waste degrades into small particles known as microplastics and nanoplastics (MNPLs), depending on their size. Given the potential harmful effects associated with MNPL exposure, it is crucial to develop environmentally representative particles for hazard assessment. These so-called true-to-life MNPLs are generated through in-house degradation of real-world plastic products. In this study, we produced titanium-doped nanoplastics (NPLs) from opaque polyethylene terephthalate (PET) milk bottles, which contain titanium dioxide as a filler. The resulting PET(Ti)-NPLs were thoroughly characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), mass spectrometry (MS), dynamic light scattering (DLS), ζ-potential measurements, transmission electron microscopy (TEM), and Fourier-transform infrared (FTIR) spectroscopy. Human-derived THP-1 monocytes were employed to investigate particle uptake kinetics, dosimetry, and genotoxicity. A combination of flow cytometry and inductively coupled plasma mass spectrometry (ICP-MS) enabled the quantification of internalized particles, while the comet assay assessed DNA damage. The results revealed dose- and time-dependent effects of PET(Ti)-NPLs on THP-1 cells, particularly in terms of internalization. Titanium doping facilitated detection and influenced genotoxic outcomes. This study demonstrates the relevance of using environmentally representative nanoplastic models for evaluating human health risks and underscores the importance of further mechanistic research. Full article

Microplastics (MPs) are becoming one of the most serious environmental threats worldwide. They have been shown to induce male reproductive toxicity in animal studies. However, evidence of their adverse effects on male reproductive health in human is still lacking. In this study, we evaluated the presence of MPs in human semen and explored their associations with semen quality. A total of 45 semen samples from men attending a fertility center were collected. MPs in the semen samples were analyzed by laser direct infrared (LD-IR) spectroscopy. MPs were found in 34 out of 45 semen samples, with an average abundance of 17.0 (42.0) particles/g. The size of MPs ranged from 20.3 μm to 189.7 μm and the majority (57.8%) were smaller than 50 μm. A total of 15 distinct MPs polymers were identified, and polyethylene (PET) accounted for 35.9% of the total amount of MPs, followed by butadiene rubber (BR, 26.4%) and chlorinated polyethylene (CPE, 12.2%). Analysis of the association of MP exposure with semen quality showed that participants exposed to PET MPs experienced a reduction in sperm progressive motility (20.6% ± 12.8% vs. 34.9% ± 15.9%, p = 0.056). However, no significant association was found between MP exposure and sperm concentration or total sperm count. Our findings confirmed the presence of MPs in human semen and suggested that MP exposure might have adverse impacts on male reproductive health. However, further large-scale studies are needed to confirm these findings. Full article

Soil microplastic pollution poses a significant threat to the integrity of terrestrial ecosystems and agricultural sustainability. This review provides a comprehensive synthesis of recent progress on soil microplastic (MP) sources, ecological impacts, and separation technologies. Agricultural practices (e.g., residual plastic mulch and wastewater irrigation) and atmospheric deposition serve as primary drivers of contamination accumulation, with pronounced spatial heterogeneity observed across regions. Predominant MP types such as polyethylene, polystyrene, and polypropylene disrupt soil structure and biogeochemical processes through three core mechanisms: physical interference, chemical toxicity, and biological accumulation. These particles further form carrier–pollutant complexes, exacerbating ecotoxicological impacts across trophic levels. While emerging separation techniques like magnetic separation and solvent extraction demonstrate enhanced efficiency, their implementation faces challenges stemming from soil matrix complexity and high operational costs. This article underscores the need for global collaborative efforts to accelerate innovation in biodegradable polymers, offering practical pathways for sustainable soil management. Full article

Small-particle-produced goods, such as those used in industry, medicine, cosmetics, paints, abrasives, and plastic pellets or powders, are the main sources of microplastics. It is also possible to mention tire recycling granules here. Larger components break down in the environment to generate secondary microplastics. Microplastics, or particles smaller than 5 mm, and nanoplastics, or particles smaller than 1 μm, are the products of degradation and, in particular, disintegration processes that occur in nature as a result of several physical, chemical, and biological variables. Polypropylene, polyethylene, polyvinyl chloride (PVC), polystyrene, polyurethane, and polyethylene terephthalate (PET) are among the chemicals included in this contamination in decreasing order of quantity. Micro- and nanoplastics have been detected in the air, water, and soil, confirming their ubiquitous presence in natural environments. Their widespread distribution poses significant threats to human health, including oxidative stress, inflammation, cellular damage, and potential carcinogenic effects. The aim of this article is to review the current literature on the occurrence of micro- and nanoplastics in various environmental compartments and to analyze the associated health consequences. The article also discusses existing legal regulations and highlights the urgent need for intensified research into the toxicological mechanisms of microplastics and the development of more effective strategies for their mitigation. Full article

Microplastics are an increasingly concerning environmental pollutant. Their presence in agricultural settings is particularly troubling due to their persistence and potential to infiltrate soil, groundwater, and the food chain. This study focused on analyzing fertilizer derived from stabilized sewage sludge collected in June and July. The average mass of microplastics isolated per 100 g of fertilizer was 461.28 mg in June and 458.92 mg in July. The analysis revealed a substantial quantity of microplastics, with fragments and fibers being the predominant forms. In the June samples, an average of 860 microplastic particles was detected, compared to 734 in July (507 fragments and 227 fibers). The most common particle sizes in June ranged from 1500 to 2000 µm and 2000 to 2500 µm, with a significant proportion also exceeding 4000 µm. In July, particles larger than 4000 µm were the most prevalent. Qualitative analysis using Raman microscopy identified polyethylene—a widely used, inexpensive, and chemically stable polymer—as one of the main types of plastic present. Full article

This study presents the development of a textile-based cascade filter for the removal of microplastics from an industrial laundry effluent. The cascade microfilter consists of three stages of 3D textile sandwich composite filter media, which have successively finer pores and are aimed at filtering microplastic particles down to 1.5 µm. Polypropylene fabrics with pore sizes of 100, 50 and 20 µm and 3D warp-knitted fabrics with high porosity (96%) were used. Filtration tests were carried out with polyethylene model microplastic particles at a concentration of 167 mg/L. To regenerate the filter and restore its filtration performance, backwashing with filtered water and compressed air was applied. Field trials at an industrial laundry facility and a municipal wastewater treatment plant confirmed high removal efficiencies. The 3D textile sandwich structure promotes filter cake formation, allowing extended backwash intervals and the effective recovery of filtration capacity between 89.7% and 98.5%. The innovative use of 3D textile composites enables a high level of microplastic removal while extending the filter media lifetime. This makes a significant contribution to the reduction in microplastic emissions in the aquatic environment. The system is scalable, space and cost efficient and adaptable to various industrial applications and is thus a promising solution for advanced wastewater treatment. Full article

Rivers are recognized as significant pathways and transportation for microplastics (MPs), an emerging contaminant, to aquatic environments. However, there is limited evidence on how riverine reservoirs influence MPs transport. To fill this gap and provide baseline empirical data and insights to South African context, the current study assessed the seasonal variation in MP densities from sediments collected upstream, within the reservoir, and downstream of the Vondo Reservoir along the Mutshindudi River. We hypothesised that MP densities would be highest within the reservoir, due to the lack of constant flow that would otherwise transport accumulated particles downriver. Additionally, we expected the cool–dry season to be associated with the highest MP densities. As expected, high MP densities were observed within the reservoir (117.38–277.46 particles kg⁻¹ dwt) when compared to the downstream (72.63–141.50 particles kg⁻¹ dwt) and upstream (28.81–91.63 particles kg⁻¹ dwt) sites of the reservoir. The cool–dry season (91.63–277.46 particles kg⁻¹ dwt) exhibited the highest MP densities compared to the hot–wet season (28.81–141.50 particles kg⁻¹ dwt). However, MP densities downstream the reservoir were higher during the hot–wet season (141.50 ± 24.34 particles kg⁻¹ dwt) compared to the cool–dry season (72.63 ± 48.85 particles kg⁻¹ dwt). The most dominant MP particles identified were white, transparent, and black fibres/filaments composed primarily of polypropylene (PP) and polyethylene (PE). This suggests diverse sources of MP particles. No significant correlations were found between water parameters and MP densities across sampling sites and seasons, indicating a widespread and context-independent presence of MPs. These findings contribute to MP studies in freshwater environments and further reinforce the role of sediments as sink for MPs and suggest that riverine reservoirs similar to dams can trap MPs, which may then be remobilized downstream during high-flow periods. Importantly, the results of this study can support local municipalities in implementing targeted plastic pollution mitigation strategies and public awareness campaigns, particularly because the Vondo Reservoir serves as a critical water resource for surrounding communities. Full article

In order to investigate the current pollution status and distribution characteristics of soil microplastics (MPs) in Bayinbuluk alpine swamp meadow, soil samples of different depths were collected from the study area. The physicochemical properties of the soil, as well as the abundance and morphological distribution of microplastics, were analyzed. The results showed that the microplastics’ abundance in the samples ranged from 46 to 266 microplastics/kg, with significantly higher levels (p < 0.05) in the 0–10 cm soil layer than in the other layers (10–100 cm). The shapes of microplastics mainly include fibrous, fragmented, thin film, and foamed, and the number of fibrous shapes is significantly higher than the other three types. Microplastic colors included black, yellow, red, blue, green, and clear, with black accounting for 70.16%, significantly more abundant than other colors (p < 0.05). Among the different particle sizes of microplastics, 0.5–1 mm microplastics comprised the largest proportion and were significantly more abundant than other particle sizes. Polyethylene (PE) was found to be a major component of soil microplastics in the study area through random sampling using Raman spectroscopy. Correlation analysis showed that the change in soil layer had a significant effect (p < 0.05) on the number, color, and particle size of microplastics. Meanwhile, an increase in microplastic abundance had a significant effect (p < 0.05) on the soil physicochemical properties. The results of RDA (Redundancy Analysis) and Monte Carlo testing showed that there was a significant correlation between microplastic quantity and soluble organic carbon and soil water content (p < 0.01). Full article

Microplastic (MP) particles are ubiquitous in the environment and pose a growing threat to ecosystem stability. As concern over their ecological impact increases, biotests and ecotoxicological approaches using plant species have become valuable tools for research. This study aimed to evaluate the effects of varying concentrations of low-density polyethylene (LDPE) MP on seed germination, root development, and shoot growth of white mustard (Sinapis alba L.) under controlled laboratory and pot experiment conditions. For the seven-day laboratory experiment, concentrations of 0.01% and 1% w/w were used, whereas concentrations of 1% and 5% w/w were applied in the ten-day pot experiment. Results indicated no statistically significant effects of LDPE MP on germination rate or germination speed index (GSI) in either setting. However, shoot length data suggest that the 5% LDPE treatment may have a slight stimulatory effect compared to the control, though this trend was marginally significant. These findings highlight the complex and context-dependent nature of MP–plant interactions. Further research is needed to better understand the mechanisms driving these responses and to support the development of mitigation strategies for MP contamination in terrestrial ecosystems. Full article

The concentration of microplastics [300–5000 µm] in the surface water of the Mayotte lagoon, Western Indian Ocean, was measured over two snapshot campaigns conducted during the dry and rainy seasons. The concentration in the surface water varied from 0.01 MP m⁻³ to 1.23 MP m⁻³ and was higher during the rainy season. All particles were analyzed via µFTIR, enabling systematic polymer and surface area determination. Polypropylene dominated over polyethylene and polystyrene, representing 70% of the microplastic particles observed. The microplastics, which were predominantly in the [0.3–1000 µm] fraction, presented a similar seasonal trend of distribution with respect to their occurrence, suggesting that turbulence and the subsequent settling of microplastics in the lagoon’s surface water were identical during the two campaigns. PCA was performed to deconvolute the effects of season and hydrodynamic features on the observed surface water concentrations and median size distribution. It evidenced a high degree of disparity in concentration and median area in surface water during the rainy season, while a lower concentration of smaller particles was observed during the end of the dry season. A microplastic risk assessment was performed for the surface water of the lagoon and evidenced a low pollution load index and low to high polymer risk assessment and potential ecological risk indexes. Full article

“Edible wild shrimp” play a crucial role in marine ecosystems and food chains, yet research on microplastic (MP) impacts on the dominant shrimp species of the Haizhou Bay Marine Ranch remains scarce. This study examined shrimp from Haizhou Bay, evaluating the distribution, nutritional characteristics, and health risks associated with microplastics in their tissues. Analytical techniques included Fourier transform infrared spectroscopy, the hot needle method, stable isotope analysis, and microplastic risk assessment. The results revealed that microplastics comprised 40.93% of all particles identified, with Oratosquilla oratoria exhibiting the highest intestinal contamination, followed by Alpheus distinguendus. Most MPs were fibrous (86.3%), predominantly blue (57.32%), and approximately 80% consisted of Polyethylene Terephthalate. Significant interspecies differences were observed in the gastrointestinal distribution of MPs, while individuals of the same species showed no notable differences across body-length groups due to molting. The estimated daily intake and margin of exposure for human consumers remained well below the no-observed-adverse-effect level, suggesting negligible health risks. These findings provide a theoretical and empirical basis for understanding the migration, sources, and ecological implications of microplastics in shrimp, offering valuable insights for assessing nearshore environmental pollution and food web dynamics. Full article

The widespread use of polyethylene terephthalate (PET) in bottled water packaging remains significant and is expected to increase further in the coming years. This trend raises concerns due to the generation of large amounts of waste. The degradation of PET leads to the release of low-molecular-weight substances and microplastic particles, which contaminate food products and the environment. This work highlights the significance of microplastic pollution, summarizes the mechanisms of PET degradation, and discusses methods for microplastic detection. A key section of the paper explores potential degradation management strategies, focusing on their applications and existing limitations. The study underscores the need for coordinated action among the scientific community, industry, and policymakers to mitigate this pressing environmental challenge. Full article