Search Results (230)

This paper presents a low-power data acquisition (DAQ) chip tailored for impulsive charge sensing, featuring a comparator-gated dynamic acquisition (CG-DAQ) architecture. A dynamic comparator triggers both the gain stage and a 12-bit successive-approximation register (SAR) analog-to-digital converter (ADC) through a shared timing path, enabling event-driven amplification and digitization. Programmable conversion gain ranging from 5 to 40 mV/pC is achieved by switching the sampling capacitance. Fabricated in TSMC 65 nm CMOS, the chip detects input charges from 0.01 to 36 pC, supports a signal bandwidth of 10 kHz to 100 kHz, and enables sampling rates up to 1 MS/s. It achieves an input-referred noise of 5.5 fC_rms and a peak signal-to-noise ratio (SNR) of 67 dB, all within a 54 μW power envelope and a compact 0.03 mm² core area. The proposed architecture facilitates accurate and energy-efficient charge-domain sensing for capacitive and piezoelectric sensor applications. Full article

This study presents an analytical and experimental approach to enhance cantilever-based piezoelectric energy harvesters by optimizing thickness distribution. Using a gradient projection algorithm within a state-space framework, the unimorph beam’s geometry is tailored while constraining the first natural frequency. The objective is to amplify axial strain within the piezoelectric layers, thereby increasing electric polarization and maximizing the conversion efficiency of mechanical vibrations into electrical energy. The steady-state response under harmonic base excitation at resonance was modeled to evaluate the harvester’s dynamic behavior against uniform-thickness counterparts. Results show that the optimized beam achieves significantly higher output voltage and energy harvesting efficiency. Simulations reveal effective strain concentration in regions of high piezoelectric sensitivity, enhancing power generation under resonant conditions. Two independent experimental setups were employed for empirical validation: a non-contact laser vibrometry system (Polytec 3D) and a first resonant base excitation setup. Eigenfrequencies matched within 5% using a Polytec multipath interferometry system, and constant excitation tests showed approximately 30% higher in optimal shapes electrical potential value generation. The outcome of this study highlights the efficacy of geometric tailoring—specifically, non-linear thickness shaping—as a key strategy in achieving enhanced energy output from piezoelectric harvesters operating at their fundamental frequency. This work establishes a practical route for optimizing unimorph structures in real-world applications requiring efficient energy capture from low-frequency ambient vibrations. Full article

This paper presents a comprehensive summary of recent advances in circuit topologies for piezoelectric energy harvesting, leading to self-powered systems (SPSs), covering the full-bridge rectifier (FBR) and half-bridge rectifier (HBR), AC-DC converters, and maximum power point tracking (MPPT) techniques. These approaches are analyzed with respect to their advantages, limitations, and overall impact on energy harvesting efficiency. Th work explores alternative methods that leverage phase shifting between voltage and current waveform components to enhance conversion performance. Additionally, it provides detailed insights into advanced design strategies, including adaptive power management algorithms, low-power control techniques, and complex impedance matching. The paper also addresses the fundamental principles and challenges of converting mechanical vibrations into electrical energy. Experimental results and performance metrics are reviewed, particularly in relation to hybrid approaches, load impedance, vibration frequency, and power conditioning requirements in energy harvesting systems. This review aims to provide researchers and engineers with a critical understanding of the current state of the art, key challenges, and emerging opportunities in piezoelectric energy harvesting. By examining recent developments, it offers valuable insights into optimizing interface circuit design for the development of efficient and self-sustaining piezoelectric energy harvesting systems. Full article

This study presents a high-order shear deformation theory (HSDT)-based model for evaluating the energy harvesting performance of functionally graded material (FGM) beams integrated with a piezoelectric layer and subjected to a moving concentrated load at constant velocity. The governing equations are derived using Hamilton’s principle, and the dynamic response is obtained through the State Function Method with trigonometric mode shapes. The output voltage and harvested power are calculated based on piezoelectric constitutive relations. A comparative analysis with homogeneous isotropic beams demonstrates that HSDT yields more accurate predictions than the Classical Beam Theory (CBT), especially for thick beams; for instance, at a span-to-thickness ratio of h/L = 12.5, HSDT predicts increases of approximately 6%, 7%, and 12% in displacement, voltage, and harvested power, respectively, compared to CBT. Parametric studies further reveal that increasing the load velocity significantly enhances the strain rate in the piezoelectric layer, resulting in higher voltage and power output, with the latter exhibiting quadratic growth. Moreover, increasing the material gradation index n reduces the beam’s effective stiffness, which amplifies vibration amplitudes and improves energy conversion efficiency. These findings underscore the importance of incorporating shear deformation and material gradation effects in the design and optimization of piezoelectric energy harvesting systems using FGM beams subjected to dynamic loading. Full article

Piezoelectric energy harvesting in roadways can power distributed sensors and electronics by capturing underutilized mechanical energy from traffic. In this research, 1-3 stacked piezocomposites were developed and evaluated to determine optimal designs for multiple applications. The design of these transducers aimed at operating in a multitude of scenarios, under compressive loads (1–10 kN) at low-frequency (10 Hz) applications, intended to simulate vehicular forces. Power comparison was utilized between numerous transducers to determine the most efficient configuration for electromechanical energy conversion. Design guidelines were based on mechanical integrity, output power, active piezoelectric volume percentage, aspect ratio, and geometric factors. The forces applied in this study were reliant on the average vehicle weight. An intermediate PZT volume fraction and moderate pillar aspect ratios were found to yield the highest power output, with the stacked 1-3 composite significantly outperforming a monolithic PZT of a similar size. Full article

With the rapid rise in Internet of Things (IoT) and artificial intelligence (AI) technologies, there is an increasing need for portable, wearable, and self-powered flexible sensing devices. In such scenarios, self-powered nanogenerators have emerged as promising energy harvesters capable of converting ambient mechanical stimuli into electrical energy, enabling the development of autonomous flexible sensors and sustainable systems. This review highlights recent advances in nanogenerator technologies—particularly those based on piezoelectric and triboelectric effects—with a focus on soft, flexible, and gel-based polymer materials. Key mechanisms of energy conversion are discussed alongside strategies to enhance performance through material innovation, structural design, and device integration. Special attention is given to the role of gel-type composites, which offer unique advantages such as mechanical tunability, self-healing ability, and biocompatibility, making them highly suitable for next-generation wearable, biomedical, and environmental sensing applications. We also explore the evolving landscape of energy applications, from microscale sensors to large-area systems, and identify critical challenges and opportunities for future research. By synthesizing progress across materials, mechanisms, and application domains, this review aims to guide the rational design of high-performance, sustainable nanogenerators for the next era of energy technologies. Full article

The currently used electrical energy devices for portable applications are in limited life and need of frequent recharging, it is a big bottleneck for wireless and transportation systems. The scientific community is motivated to find innovative and efficient devices to convert environmental energy into useful forms. Nanogenerator can mitigate this issue by harvesting ambient energy of different forms into useful electrical energy. Particularly flexible nanogenerators can efficiently convert ambient mechanical energy into electrical energy which can be fruitfully used for self-powered sensors and electronic appliances. Zinc oxide is an interesting photosensitive and piezoelectric material that is expected to play a vital role in the synergetic harvesting of environmental thermal, sound, mechanical, and solar energies. As ZnO can be synthesized using easy methods and materials at low cost, the conversion efficiencies of solar and other energy forms can increase considerably. ZnO is a versatile material with interesting semiconducting, optical, and piezoelectric properties; it can be used advantageously to harvest more than one type of ambient energy. The coupled semiconducting and piezoelectric properties of ZnO are attractive for fabricating nanogenerators capable of harvesting both ambient optical and mechanical energies simultaneously. These nanolevel conversion devices are much required to power remote and implantable devices without the need for additional power sources. The present review briefly discusses the principles and mechanisms of different energy harvesting abilities of ZnO nanorods and their composites by consolidating available literature. In addition, the developments taking place in nanogenerators of different kinds—such as photovoltaic, piezoelectric, pyroelectric, and triboelectrics for self-powered technology—and their progress in hybrid energy harvesting application is reviewed. Full article

Nanogenerators have garnered significant scholarly interest as a groundbreaking approach to energy harvesting, encompassing applications in self-sustaining electronics, biomedical devices, and environmental monitoring. The rise of additive manufacturing has fundamentally transformed the production processes of nanocomposites, allowing for the detailed design and refinement of materials aimed at optimizing energy generation. This review presents a comprehensive analysis of 3D-printed nanocomposites in the context of nanogenerator applications. By employing layer-by-layer deposition, multi-material integration, and custom microstructural architectures, 3D-printed nanocomposites exhibit improved mechanical properties, superior energy conversion efficiency, and increased structural complexity when compared to their conventionally manufactured counterparts. Polymers, particularly those with inherent dielectric, piezoelectric, or triboelectric characteristics, serve as critical functional matrices in these composites, offering mechanical flexibility, processability, and compatibility with diverse nanoparticles. In particular, the careful regulation of the nanoparticle distribution in 3D printing significantly enhances piezoelectric and triboelectric functionalities, resulting in a higher energy output and greater consistency. Recent investigations into three-dimensional-printed nanogenerators reveal extraordinary outputs, encompassing peak voltages of as much as 120 V for BaTiO₃-PVDF composites, energy densities surpassing 3.5 mJ/cm², and effective d₃₃ values attaining 35 pC/N, thereby emphasizing the transformative influence of additive manufacturing on the performance of energy harvesting. Furthermore, the scalability and cost-effectiveness inherent in additive manufacturing provide substantial benefits by reducing material waste and streamlining multi-phase processing. Nonetheless, despite these advantages, challenges such as environmental resilience, long-term durability, and the fine-tuning of printing parameters remain critical hurdles for widespread adoption. This assessment highlights the transformative potential of 3D printing in advancing nanogenerator technology and offers valuable insights into future research directions for developing high-efficiency, sustainable, and scalable energy-harvesting systems. Full article

The technological advances in internet of things (IoT) devices have raised the demand for cost-efficient and sustainable energy sources. Piezoelectric energy harvesters (PEHs) are promising low-cost and eco-friendly energy sources but require robust power management circuits (PMCs) for voltage conversion and regulation. This work presents a complementary metal–oxide–semiconductor (CMOS)-based PMC, integrating a reconfigurable AC-DC rectifier and a low-dropout (LDO) voltage regulator designed using 0.18 µm Taiwan semiconductor manufacturing company (TSMC) CMOS technology. This design includes an intermediate coupling stage to reduce voltage drop and improve the transfer efficiency of the PMC. In addition, we develop numerical simulations of the PMC performance, achieving a voltage conversion efficiency (VCE) between 72.8% and 43.21% using input voltages from 0.7 V to 2.8 V with a 50 kΩ load resistance. Compared to previous designs, the proposed circuit demonstrates improved stability, reduced area (66.28 mm²), and extended operating voltage range, allowing its potential application for ultra-low-power IoT nodes. This PMC contributes to the development of autonomous systems with reduced battery dependency and enhanced sustainability. Full article

Wave energy is a widely distributed, abundant, and clean renewable energy source with tremendous potential for development. This study presents a multi-unit coupled motion hybrid generator (MCM-HG) based on a pendulum structure for harvesting low-frequency wave energy. The device integrates eight power generation units, including triboelectric nanogenerators (TENGs), electromagnetic generators (EMGs), and piezoelectric nanogenerators (PENGs), enhancing space utilization and energy conversion efficiency through coupled motion. Experiments show that at a frequency of 0.5 Hz and a swing angle of 15°, the MCM-HG achieves an output power of 22.07 mW and a power density of 7.36 Wm⁻³. The device successfully powers microelectronic devices, demonstrating its potential application value in the marine Internet of Things. Full article

Fluid–structure interaction-based energy-harvesting technology has gained significant attention due to its potential for energy conversion. However, most existing studies primarily focus on energy capture, resulting in incomplete systems with limited portability and a lack of integrated circuitry. To address these limitations, this study presents a portable, integrated piezoelectric flag energy-harvesting system that achieves a complete closed-loop conversion from fluid kinetic energy, through structural strain energy, to electrical energy. The system utilizes an upstream bluff body to generate vortex-induced vibrations, a downstream support structure that maintains operational stability, and an internally integrated wiring channel that enables overall energy conversion. Charge–discharge experiments on the energy storage unit enable a comprehensive evaluation of system performance, marking the first efficiency measurement of a fully integrated energy-harvesting system. Experimental results demonstrate the first quantified map of losses across all conversion stages in a portable piezo-flag platform, highlighting the system’s potential for powering small-scale, low-power self-sustaining devices. This work establishes a reference framework and provides a novel technological pathway for advancing practical applications of fluid-induced energy harvesting, contributing to the development of autonomous power sources in various engineering fields. Full article

This study proposes a membrane-type metamaterial with digitally controlled piezoelectric actuation for low-frequency sound absorption applications. The hybrid structure integrates an aluminum membrane functionally bonded with programmable piezoelectric patches (PZTs) and a sealed air cavity. Two innovative control strategies—Resistance Enhancement and Resonance Enhancement—dynamically adjust circuit impedance to maximize electromechanical energy conversion efficiency, thereby optimizing absorption at targeted frequencies. These strategies are implemented via a real-time digital feedback system. A coupled piezoelectric-structural-acoustic model is established to characterize the system’s transfer function, with validation through both finite element simulations and impedance tube experiments. Numerical and experimental results demonstrate nearly complete absorption around the resonant frequency, and the bandwidth can be further broadened through multi-resonance superposition. Theoretical analysis confirms that the active control strategies simultaneously modulate the acoustic impedance components (resistance and reactance), thereby optimizing electromechanical energy conversion efficiency. This work establishes a novel active-control methodology for low-frequency and high-efficiency noise mitigation. Full article

The growing demand for sustainable and self-powered technologies in automotive applications has led to increased interest in energy harvesting from vehicle suspensions. Recovering mechanical energy from road-induced vibrations offers a viable solution for powering wireless sensors and autonomous electronic systems, reducing dependence on external power sources. This study presents the design, modeling, and experimental validation of a hybrid energy-harvesting system that integrates piezoelectric and magnetoelectric effects to efficiently convert mechanical vibrations into electrical energy. A model-based systems engineering (MBSE) approach was used to optimize the system architecture, ensuring high energy conversion efficiency, durability, and seamless integration into suspension systems. The theoretical modeling of both piezoelectric and magnetoelectric energy harvesting mechanisms was developed, providing analytical expressions for the harvested power as a function of system parameters. The designed system was then fabricated and tested under controlled mechanical excitations to validate the theoretical models. Experimental results demonstrate that the hybrid system achieves a maximum power output of 16 µW/cm² from the piezoelectric effect and 3.5 µW/cm² from the magnetoelectric effect. The strong correlation between theoretical predictions and experimental measurements confirms the feasibility of this hybrid approach for self-powered automotive applications. Full article

The growing global demand for sustainable energy solutions has led to increased interest in kinetic energy harvesting as a viable alternative to traditional power sources. High-foot-traffic environments, such as public spaces and religious sites, generate significant mechanical energy that often remains untapped. This study explores energy-harvesting technologies applicable to public areas with heavy foot traffic, focusing on Al-Haram Mosque in Saudi Arabia—one of the most densely populated religious sites in the world. The research investigates the potential of piezoelectric, triboelectric, and hybrid systems to convert pedestrian foot traffic into electrical energy, addressing challenges such as efficiency, durability, scalability, and integration with existing infrastructure. Piezoelectric materials, including PVDF and BaTiO₃, effectively convert mechanical stress from footsteps into electricity, while triboelectric nanogenerators (TENGs) utilize contact electrification for lightweight, flexible energy capture. In addition, this study examines material innovations such as 3D-printed biomimetic structures, MXene-based composites (MXene is a two-dimensional material made from transition metal carbides, nitrides, and carbonitrides), and hybrid nanogenerators to improve the longevity and scalability of energy-harvesting systems in high-density footfall environments. Proposed applications for Al-Haram Mosque include energy-harvesting mats embedded with piezoelectric and triboelectric elements to power IoT devices, LED lighting, and environmental sensors. While challenges remain in material degradation, scalability, and cost, emerging hybrid systems and advanced composites present a promising pathway toward sustainable, self-powered infrastructure in large-scale, high-foot-traffic settings. These findings offer a transformative approach to energy sustainability, reducing reliance on traditional energy sources and contributing to Saudi Arabia’s Vision 2030 for renewable energy adoption. Full article

Energy harvesting in the automotive sector is a rapidly growing field aimed at improving vehicle efficiency and sustainability by recovering wasted energy. Various technologies have been developed to convert mechanical, thermal, and environmental energy into electrical power, reducing dependency on traditional energy sources. This manuscript provides a comprehensive review of energy harvesting applications/methodologies, aiming to trace the research lines and future developments. This work identifies the main categories of harvesting solutions, namely mechanical, thermal, and hybrid/environmental solar–wind systems; each section includes a detailed review of the technical and scientific state of the art and a comparative analysis with detailed tables, allowing the state of the art to be mapped for identification of the strengths of each solution, as well as the challenges and future developments needed to enhance the technological level. These improvements focus on energy conversion efficiency, material innovation, vehicle integration, energy savings, and environmental sustainability. The mechanical harvesting section focuses on energy recovery from vehicle vibrations, with emphasis on regenerative suspensions and piezoelectric-based solutions. Specifically, solutions applied to suspensions with electric generators can achieve power outputs of around 1 kW, while piezoelectric-based suspension systems can generate up to tens of watts. The thermal harvesting section, instead, explores methods for converting waste heat from an internal combustion engine (ICE) into electrical power, including thermoelectric generators (TEGs) and organic Rankine cycle systems (ORC). Notably, ICEs with TEGs can recover above 1 kW of power, while ICE-based ORC systems can generate tens of watts. On the other hand, TEGs integrated into braking systems can harvest a few watts of power. Then, hybrid solutions are discussed, focusing on integrated mechanical and thermal energy recovery systems, as well as solar and wind energy harvesting. Hybrid solutions can achieve power outputs above 1 kW, with the main contribution from TEGs (≈1 kW), compared to piezoelectric systems (hundreds of W). Lastly, a section on commercial solutions highlights how current scientific research meets the automotive sector’s needs, providing significant insights for future development. For these reasons, the research results aim to be guidelines for a better understanding of where future studies should focus to improve the technological level and efficiency of energy harvesting solutions in the automotive sector. Full article