Search Results (111)

In this study, oil sludge was utilized as a carbon source to prepare a carbon-based catalyst. By leveraging the oil sludge’s inherent iron content and subsequently introducing exogenous copper, a CuO/Fe₂O₃/carbon composite material (OSC-0.75Cu) was synthesized for the activation of peroxymonosulfate (PMS) to degrade p-nitrophenol. The OSC-0.75Cu/PMS system achieved a degradation efficiency of 92.19%, which was 2.91 times that of the OSC/PMS system (31.71%), and its reaction rate constant (k_obs) was 8.9 times greater. Furthermore, in simulated water matrices (containing anions and fulvic acid) and three real water matrices (rainwater, moat water, and Yangtze River water), the OSC-0.75Cu/PMS systemachieved PNP degradation efficiencies ranging from 71.63% to 76.36%. The degradation of p-nitrophenol in this system involves three primary reactive species: hydroxyl radicals (•OH), sulfate radicals (•SO₄⁻), and singlet oxygen (¹O₂), among which ¹O₂ plays the dominant role. The coexistence of Cu and Fe species may facilitate surface redox reactions during PMS activation, while defect-related oxygen sites may contribute to PMS adsorption and activation and the generation of ¹O₂. This study provides a novel strategy that enables the resource utilization of oil sludge while simultaneously addressing environmental remediation challenges. Full article

This work presents a sustainable strategy for the fabrication of multifunctional silver nanoparticles (Ag-NPs) and Ag/jute nanocomposites using Erythroxylum coca tea waste extract as a bioreducing and stabilizing agent, combined with picosecond pulsed laser irradiation. UV–Vis spectroscopy and transmission electron microscopy revealed the formation of Ag-NPs with diverse morphologies and broad size distributions, which became significantly more uniform after laser post-treatment without the need for additional chemical reagents. Following laser irradiation, the initially broad Ag surface plasmon resonance (SPR) peak transformed into a symmetric Gaussian-shaped band, centered at 407 ± 3 nm for all the Ag-NPs systems. The catalytic performance of unsupported Ag-NPs and Ag-NPs supported on jute fibers was comparatively evaluated by degrading Congo red (CR) dye, revealing that the supported nanocomposites exhibited enhanced catalytic stability, higher pollutant removal efficiency, and improved catalyst recovery. Furthermore, multicomponent catalytic reduction experiments involving CR and 4-nitrophenol (4-NP) in the presence of NaBH₄ revealed simultaneous degradation and reduction pathways mediated by the Ag/jute nanocomposites, as evidenced by the emergence of new absorption bands during the reaction. In parallel, the synthesized Ag-NPs demonstrated pronounced antimicrobial activity against Escherichia coli, generating well-defined inhibition zones. Beyond conventional approaches centered on nanoparticle synthesis and morphology optimization, this study establishes a platform that combines agricultural waste valorization, laser-assisted nanoparticle engineering, and natural-fiber-supported nanocomposite fabrication, enabling efficient remediation of both single- and multicomponent pollutant systems while promoting catalyst reusability and environmental sustainability. These findings demonstrate the Ag/jute nanocomposites as sustainable and scalable catalytic materials for wastewater remediation and antimicrobial applications. Full article

Using density functional theory (DFT) and the Gaussian 09 program, the study calculated Gibbs free energy to understand how easily each NP can transform. Results showed that only 2,6-dinitrophenol (2,6-DNP) and 2-chloro-6-nitrophenol (2-Cl-6-NP) had Gibbs free energies above 0 kJ/mol. The study also evaluated the toxicity of the NPs, leading to the identification of trinitrophenol (TNP), 2-chloro-4-nitrophenol (2-Cl-4-NP), and 2-nitrophenol (2-NP) with the highest risk scores. In the present study, binding energies were used only as comparative indicators of enzyme–substrate interaction favorability within a screening framework, rather than direct measures of catalytic degradation efficiency. The enzyme 1,2-dioxygenase from Acinetobacter baylyi ADP1 showed strong degradation effects on catechol, with significant binding energies for 2-NP, 2-Cl-4-NP, and TNP. The PS-AOP changed the degradation environment, which reduced enzymatic efficiency. The study also modified specific amino acids in enzymes to improve their performance. For example, the enzyme 1DLT-6 had a degradation increase of nearly 27% compared to the reference enzyme. Finally, we tried to measure the impact of different forces on the breakdown of nitrophenols by enzymes. We used a two-dimensional amino acid map based on enzyme–ligand interactions and a visualization of non-covalent interactions. Our findings show that van der Waals forces and electrostatic forces are the main factors affecting how well the material breaks down. From a sustainability perspective, the study highlights a promising strategy for mitigating secondary pollution, improving the environmental compatibility of PS-AOP-based remediation, and supporting safer and more sustainable restoration of petroleum hydrocarbon-contaminated soil and groundwater. These findings help strengthen the theoretical basis for developing greener post-oxidation remediation pathways. Full article

Nitrophenol (NP) and methylene blue (MB) are considered among the most hazardous organic contaminants frequently released from pharmaceutical, textile, and paper industries, posing significant risks to both human health and the environment. The conventional treatment involves adsorption, oxidation, biological, filtration, and other photochemical degradation methods, which often suffer from low efficiency, limited reusability, and the production of secondary toxic by-products. In this context, the nanomaterials (NMs) mediated catalytic reduction of MB into leucomethylene blue and p-NP into p-aminophenol (p-AP) has emerged as a promising approach, due to its high efficiency and effectiveness. This review emphasizes the green synthesis of NMs for catalytic applications, which align with the principles of the circular economy and the Sustainable Development Goals (SDGs). This thorough review systematically examines the mechanistic understanding of the reduction of both p-NP and MB via different green synthesized NMs and evaluating their catalytic efficiencies. Furthermore, a detailed discussion of the reduction of pollutants (p-NP and MB) is provided, along with their mechanistic insights. In addition, this paper also provides a comparative table highlighting the effects of using different precursors, experimental conditions on the conversion catalytic efficiency and reusability potency. Thus, this work provides the insights into recent research on the catalytic reduction of p-NP and MB into valuable products, highlighting the significance of green synthesized nanocatalysts for effective wastewater treatment. Full article

p-Nitrophenol (PNP), a highly toxic and recalcitrant organic pollutant prevalent in industrial wastewater, poses severe challenges to traditional Fenton treatment technologies. In this study, a novel nanoporous catalyst is synthesized via a combined annealing–dealloying strategy. Annealing at 550 °C and 600 °C induces partial crystallization, generating α-Fe and Fe₂B phases that serve as preferential corrosion sites during chemical dealloying. This process results in a three-dimensionally interconnected nanoporous structure, which significantly increases the specific surface area of the catalyst to 2.642 m²/g. The optimized nanoporous catalyst exhibits excellent degradation performance, achieving complete removal of PNP within 30 min under room temperature reaction conditions. Notably, kinetic analysis reveals a degradation mechanism involving adsorption and Fenton-like catalysis. The high specific surface area provides abundant active sites for PNP adsorption, while the enhanced Fe²⁺ dissolution synergistically accelerates the degradation. The adsorption kinetic follows a pseudo-second-order model, and the degradation kinetic conforms to a first-order model, with activation energy analysis further confirming a surface-reaction-controlled process. This work provides a feasible approach and technical reference for designing efficient porous catalysts based on amorphous alloys for advanced treatment of refractory organic wastewater. Full article

Understanding how the surface charge environment governs pollutant–catalyst interactions is essential for designing efficient photocatalysts. In this study, ZnO–CeO₂–WO₃ composite materials were synthesized through a simplex-centroid mixture design to evaluate their photocatalytic activity toward the degradation of 4-nitrophenol (4-NPOH) under UV irradiation. The materials were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), UV–Vis diffuse reflectance spectroscopy (DRS), photoluminescence (PL), nitrogen adsorption–desorption (BET/DFT) and scanning electron microscopy (SEM). Photocatalytic experiments were conducted without pH adjustment to analyze the intrinsic behavior of each oxide and their mixtures. The acid–base equilibrium of 4-NPOH (pK_a = 7.2) allowed evaluating its deprotonation to 4-nitrophenolate (4-NP⁻) and its interaction with the catalyst surface, which depends on the point of zero charge (pH_Pzc) of ZnO, CeO₂, and WO₃. The Zn–W binary system (ZnWO₄ phase) exhibited the highest activity, achieving 81% degradation efficiency and the largest apparent rate constant (k = 5.1 × 10⁻³ min⁻¹). However, a 51% decrease in activity was observed after three reuse cycles, attributed to WO₃ leaching induced by the interaction between 4-NPO⁻ and zinc tungstate hydroxide (Zn[W(OH)₈]). This work establishes a direct correlation between surface charge, pollutant speciation, and photocatalytic performance, providing a mechanistic framework for understanding pH-dependent degradation processes over multicomponent oxide composites. Full article

This study quantifies radical pathways and the influence of process variables in a 425 kHz sonoreactor through a coupled calorimetric and multidosimetric approach during Sunset Yellow FCF degradation. Reactive oxygen species were mapped with four complementary dosimeters. Potassium iodide (KI) tracked interfacial hydroxyl radicals (^•OH). KI with ammonium heptamolybdate (AHM) captured ^•OH radicals together with hydrogen peroxide (H₂O₂). Bulk H₂O₂ accumulation integrated the recombination branch. Hydroxylation of 4-nitrophenol to 4-nitrocatechol acted as a selective near-interface ^•OH probe. Calorimetry showed that acoustic power density increased with set power and decreased with liquid height. All four dosimeters rose coherently with this variable, indicating that stronger driving elevated ^•OH generation while channeling a larger fraction into H₂O₂ through recombination. Process studies linked energy delivery to performance across operating conditions. Higher power accelerated pseudo-first order dye decay. Increasing initial dye concentration reduced fractional removal at fixed power, consistent with a radical-limited regime. Acidic media enhanced degradation by maintaining a stronger hydroxyl radical to water redox couple and by improving H₂O₂ persistence. Near neutral and alkaline media exhibited carbonate and bicarbonate scavenging of hydroxyl radicals and faster peroxide loss. Dissolved gas identity strongly modulated activity. Oxygen and argon outperformed air and carbon dioxide due to the combined thermophysical and chemical roles of the bubble gas. The calorimetry anchored and multidosimetric protocol provides a general route to compare reactors, optimize conditions, and support scale-up based on delivered energy density. Ultrasonication-driven degradation is a robust, practical technology for advanced treatment of dye-laden waters. Full article

The pervasive discharge of synthetic dyes into aquatic ecosystems poses a significant threat due to their chemical stability, low biodegradability, and carcinogenicity. Conventional dye remediation methods—such as biological treatments, coagulation, and adsorption—have demonstrated limited efficiency and poor reusability, particularly against resilient azo dyes. Cerium oxide (CeO₂) nanoparticles have gained traction as photocatalysts owing to their redox-active surfaces and oxygen storage capabilities; however, issues like particle agglomeration and rapid charge recombination restrict their catalytic performance. To address these challenges, this study presents the novel synthesis of a graphene oxide–cerium oxide (GO-CeO₂) nanocomposite via a facile in situ hydrothermal approach, using graphite from lead pencils as a sustainable precursor. The composite was structurally characterized using UV–visible spectroscopy, XRD, FTIR, and TEM. The GO matrix not only facilitates uniform dispersion of CeO₂ nanoparticles but also enhances interfacial electron mobility and active site availability. The nanocomposite demonstrated exceptional photocatalytic degradation efficiencies for methyl orange (94%), methyl red (98%), congo red (96%), and 4-nitrophenol (85.6%) under sunlight irradiation, with first-order rate constants significantly exceeding those of pure CeO₂. Notably, GO–CeO₂ retained strong catalytic activity over four degradation cycles, confirming its recyclability and structural stability. Total organic carbon (TOC) analysis revealed 79% mineralization of methyl orange, outperforming CeO₂ (45%), indicating near-complete conversion into benign byproducts. This work contributes a scalable, low-cost, and highly active heterogeneous photocatalyst for wastewater treatment, combining green synthesis principles with improved photodegradation kinetics. Its modular architecture and reusability make it a promising candidate for future environmental remediation technologies and integrated photocatalytic systems. Full article

Environmental pollution and sustainability issues require environmentally friendly solutions. In this study, we synthesized copper oxide nanoparticles (CuO NPs) using a sol––gel method with Croton macrostachyus bark extract for application in environmental remediation and as an antimicrobial agent. The uncalcined CuO NPs (200 mg/mL) demonstrated strong antimicrobial activity, with inhibition zones of 22 ± 1.3 mm against Staphylococcus aureus and 11 ± 0.7 mm against Escherichia coli. Moreover, the nanoparticles efficiently catalyzed the reduction of 4-nitrophenol, achieving 98.79% degradation within 8 min (K_app = 0.507 min⁻¹). These findings show that CuO NPs synthesized from the extract of Croton macrostachyus provide a sustainable and efficient approach for addressing both environmental pollution and antibacterial resistance. Full article

This study explores the green synthesis of silver-doped lanthanum oxide (La/Ag), silver-doped yttrium oxide (Y/Ag), and silver-doped lanthanum–yttrium oxide (La/Y/Ag) nanocomposites using Catharanthus roseus extract as a natural reducing and stabilizing agent. The nanocomposites were characterized using various spectroscopic techniques to confirm their morphology, composition, crystallinity, and functional groups. La/Ag, Y/Ag, and La/Y/Ag exhibited significant catalytic activity in the reduction and degradation of methylene blue (MB), methyl orange (MO), acridine orange (AO), and 4-nitrophenol (4-NP). Optimization studies showed that La/Ag achieved complete MB reduction within 3 min, while La/Y/Ag reduced MO in 90 s. Both catalysts maintained high activity over multiple cycles, with only slight efficiency loss. In real water media, La/Ag and La/Y/Ag achieved reduction efficiencies of 98% and 97%, respectively. La/Ag also demonstrated excellent photocatalytic degradation of AO under UV light, achieving complete degradation in 80 min, and 98% degradation in tap and seawater samples. Additionally, the nanocomposites demonstrated broad-spectrum antimicrobial activity against bacterial and fungal pathogens, with varying inhibition levels across species. Full article

This study presents a statistical modelling and optimization of an argon-activated electrohydraulic plasma discharge (EHPD) process for the degradation and mineralization of p-nitrophenol (p-NP) in water. The EHPD reactor design incorporated dual dielectric plates to initiate plasma discharge through a central orifice. A fractional factorial design (FFD) was first employed to screen four operating variables, including argon flow rate, pH, applied power, and persulfate dosage, on the p-NP degradation efficiency and energy yield, revealing argon flow rate and applied power as two identified, significant process factors. These were then further optimized using a central composite design (CCD) and response surface methodology (RSM), with the optimal operating condition found to be 2.73 L/min and 128.6 W for argon flow rate and applied power, respectively. Under the optimal operating conditions, 10 min treatment of 50 mg/L p-NP achieved a degradation efficiency of 94.2% and 75.8% total organic carbon (TOC) removal, along with a first-order reaction rate constant of 0.296 min⁻¹ and an energy efficiency of 0.22 g/kWh. The reaction mechanism for p-NP degradation by EHPD was proposed and confirmed with optical emission spectroscopy and radical scavengers. The optimized EHPD process proved both effective and energy-efficient in treating p-nitrophenol, highlighting its potential as a scalable and sustainable plasma-based technology for eliminating persistent organic pollutants and promoting greener water treatment practices. Full article

To mitigate the consumption of active sites on co-catalysts by H₂O₂ and to enhance the efficiency and stability of co-catalytic Fenton reactions, an external circulation two-stage packed-bed reactor (ECTPBR) was developed using DPW (diatomite plate@polydopamine@WC) as a co-catalyst to degrade 4-nitrophenol (4-NP). Under suitable conditions, the ECTPBR could achieve over 91.97% 4-NP degradation, with low iron sludge production (11.97 mg/L) and minimal tungsten leaching (3.6363 mg/L). The two-stage strategy enabled spatial separation of Fe³⁺ reduction and Fenton reactions, minimizing the loss of active sites on DPW, ensuring long-term system stability, and reducing the toxicity of 4-NPdegradation products. In addition, external circulation enhanced mass transfer and improved resistance to shock loads. These advantages suggest that the ECTPBR may serve as an effective strategy for applying co-catalytic Fenton reactions in the treatment of toxic and refractory organic wastewater. Full article

Canvas paintings are prone to biodeterioration due to their complex chemical composition, which can support fungal growth even under controlled conditions. This study evaluated the susceptibility of common synthetic restoration materials—Lascaux glues (303 HV, 498 HV), Acrylharz P550, BEVA 371, Laropal A81, and Regalrez 1094—to degradation by fourteen xerotolerant/xerophilic fungal strains. All tested Aspergillus and Penicillium species extensively colonized, especially artificially aged materials. FTIR-PAS analysis revealed chemical changes in carbonyl and C–H bonds in Laropal A81 and Regalrez 1094 colonized by Aspergillus spp. Scanning electron microscopy (SEM) imaging showed thinning of Lascaux glues and deformation of Regalrez 1094. Transcriptomic profiling of A. puulaauensis grown on Lascaux 498 HV and Regalrez 1094 identified altered expression of genes coding for esterases and oxidases, enzymes involved in synthetic polymer degradation. Esterase activity assays using 4-nitrophenol-based substrates confirmed significant enzymatic activity correlating with the presence of ester bonds. These findings highlight the vulnerability of synthetic restoration materials, specifically Laropal A81, Regalrez 1094, and Lascaux glues, to extremophilic fungi thriving in environments with low water activity. The results emphasize the urgent need for specific knowledge on fungi and their metabolic pathways to use/develop more durable conservation materials and strategies to protect cultural heritage objects from biodeterioration. Full article

The green-chemical preparation of silver nanoparticles (AgNPs) offers a sustainable and environmentally friendly alternative to conventional synthesis methods, thereby representing a paradigm shift in the field of nanotechnology. The biological synthesis process, which involves the synthesis, characterization, and management of materials, as well as their further development at the nanoscale, is the most economical, environmentally friendly, and rapid synthesis process compared to physical and chemical processes. Ligustrum ovalifolium flower extract was used for the preparation of AgNPs. The synthesized AgNPs were examined by using UV–visible spectroscopy, XRD, SEM, and TEM analysis. It indicates that AgNPs were formed in good size. AgNPs were applied as a catalyst for the degradation of pollutants, such as methyl orange, Congo red, and methylene blue, which were degraded within 8–16 min. Additionally, the reduction of para-nitrophenol (PNP) to para-aminophenol (PAP) was achieved within 2 min. This work demonstrates a practical, reproducible, and efficient method for synthesizing cost-effective and stable AgNPs, which serve as active catalysts for the rapid degradation of hazardous organic dyes in an aqueous environment. Full article

To successfully prepare cellulose hydrogels through a dissolution–regeneration process, 60 wt% LiBr aqueous solution was used as a green solvent. Carboxyl groups were precisely introduced onto the surface of the cellulose hydrogels through a TEMPO-mediated oxidation reaction, while the three-dimensional network structure and open pore morphology were completely retained. This modification strategy significantly enhanced the loading capacity of the hydrogels with copper nanoparticles (Cu NPs). The experimental results show that the LiBr aqueous solution can efficiently dissolve cellulose, and the TEMPO oxidation introduces carboxyl groups without destroying the stability of the hydrogels. Cu NPs are uniformly dispersed and highly loaded on the surface of the hydrogel because of the anchoring effect of the carboxyl groups. Cu NP-loaded hydrogels exhibit excellent catalytic activity in the NaBH₄ reduction of 4-nitrophenol (4-NP). Cu NP-loaded hydrogels maintain their complete structure and good catalytic performance after five consecutive cycles. Moreover, Cu NP-loaded hydrogels demonstrate high efficiency in degrading organic dyes such as methyl orange and Congo red. This study successfully developed efficient, low-cost, and environmentally friendly Cu NP-loaded hydrogel catalysts through the synergistic effect of LiBr green solvent and TEMPO oxidation modification, providing a feasible alternative to noble metal catalysts. Full article