Search Results (1,061)

Traditional forced-air cooling systems suffer from excessive energy consumption and noise pollution. This study proposes an innovative passive cooling strategy through developing aqueous radiative cooling coatings made from a combination of TiO₂-decorated carbon nanotube (TiO₂-CNT) hybrids and polyacrylic acid (PAA), designed to simultaneously enhance the heat dissipation and improve the mechanical strength of the coating films. Based on CNTs’ exceptional thermal conductivity and record-high infrared emissivity, bead-like TiO₂-CNT architectures have been prepared as the filler in PAA. The TiO₂ nanoparticles were in situ grown on CNTs, forming a rough surface that can produce asperity contacts and enhance the strength of the TiO₂-CNT/PAA composite. Moreover, this composite enhanced heat dissipation and achieved remarkable cooling efficiency at a small fraction of the filler (0.1 wt%). The optimized coating demonstrated a temperature reduction of 23.8 °C at an operation temperature of 180.7 °C, coupled with obvious mechanical reinforcement (tensile strength from 13.7 MPa of pure PAA to 17.1 MPa). This work achieves the combination of CNT and TiO₂ nanoparticles for strong radiative cooling coating, important for energy-efficient thermal management. Full article

Heavy metal contamination in natural waters and soils poses a significant environmental challenge, necessitating efficient and sustainable water treatment solutions. This study presents the computational design of low-density polyethylene (LDPE) films functionalized with iron oxide (Fe₃O₄) nanoparticles (NPs) for enhanced water purification applications. Composite materials containing 5%, 10%, and 15% were synthesized and characterized in terms of adsorption efficiency, surface morphology, and reusability. Advanced molecular modeling using BIOVIA Pipeline was employed to investigate charge distribution, functional group behaviour, and atomic-scale interactions between polymer chains and metal ions. The computational results revealed structure–property relationships crucial for optimizing adsorption performance and understanding geochemically driven interaction mechanisms. The LDPE/Fe₃O₄ composites demonstrated significant removal efficiency of Cu²⁺ and Ni²⁺ ions, along with favourable mechanical properties and regeneration potential. These findings highlight the synergistic role of mineral–polymer interfaces in water remediation, presenting a scalable approach to designing multifunctional polymeric materials for environmental applications. This study contributes to the growing field of polymer-based adsorbents, reinforcing their value in sustainable water treatment technologies and environmental protection efforts. Full article

Polymeric composite thin films have emerged as promising antimicrobial materials, particularly in response to rising antibiotic resistance. This review highlights the development and application of such films produced by laser-based deposition techniques, notably pulsed laser deposition and matrix-assisted pulsed laser evaporation. These methods offer precise control over film composition, structure, and thickness, making them ideal for embedding antimicrobial agents such as metal nanoparticles, antibiotics, and natural compounds into polymeric matrices. The resulting composite coatings exhibit enhanced antimicrobial properties against a wide range of pathogens, including antibiotic-resistant strains, by leveraging mechanisms such as ion release, reactive oxygen species generation, and membrane disruption. The review also discusses critical parameters influencing antimicrobial efficacy, including film morphology, composition, and substrate interactions. Applications include biomedical devices, implants, wound dressings, and surfaces in the healthcare and food industries. Full article

Hydrogel films receive significant attention among researchers because they combine increased stimuli responsiveness and faster responses to the already excellent properties of their component materials. However, their preparation is complex and requires that many difficulties are overcome. The present work presents a new study regarding the preparation of pure and nanoparticle-loaded alginate-based films by spin-coating. Two-microliter solutions of sodium alginate and calcium chloride with different concentrations were deposited on a glass substrate and subjected to rapid rotations of between 100 and 1000 RPM. Film formation can be achieved by optimizing the ratio between the viscosity of the solutions, depending on their concentrations and the rotation speed. When these conditions are in the right range, a homogeneous film is obtained, showing good adherence to the substrate and uniform thickness. Films containing silver nanoparticles were prepared, exploiting the reaction between sodium borohydride and silver nitrate. The two reagents were added to the sodium alginate and calcium nitrate solution, respectively. Their concentration is the driving force for the formation of a uniform film: particles of about 50 nm that are well-dispersed throughout the film are obtained using AgNO₃ at 4 mM and NaBH₄ at 2 or 0.2 mM; meanwhile, at higher concentrations, one can also obtain the precipitation of inorganic crystals. Full article

Honey, propolis or royal jelly are considered natural remedies with therapeutic properties since antiquity. Many papers explore the development of antimicrobial biomaterials based on individual bee products, but there is a lack of studies on their synergistic effects. Combining honey, propolis and royal jelly with silver nanoparticles in a biopolymer matrix offers a synergistic strategy to combat antibiotic-resistant bacterial infections. This approach supports progress in wound healing, soft tissue engineering and other domains where elimination of the microorganisms is needed like food packaging. In this study we have obtained antimicrobial films based on bee products and silver nanoparticles (AgNPs) incorporated in an alginate–chitosan blend. The novel biomaterials were analyzed by UV-Vis, fluorescence and FTIR spectroscopy or microscopy, SEM and thermal analysis. Antibacterial tests were conducted against both Gram-positive and Gram-negative bacteria, while the antifungal properties were tested against Candida albicans. The diameters for growth inhibition zones were up to 10 mm for bacterial strains and 8 mm for the fungal strain. Additionally, cytotoxicity assays were performed to evaluate the biocompatibility of the materials, the results indicating that the combination of honey, propolis, royal jelly and AgNPs does not produce synergistic toxicity. Full article

Fruit and vegetable production is often impacted by microbial pathogens that compromise the quality of produce and lead to significant economic losses at the postharvest stages. Due to their efficacy, agrochemicals are widely applied in disease management; nevertheless, this practice has led to the appearance of microbial strains resistant to these types of agrochemicals. Additionally, there is growing concern among consumers about the presence of these chemical residues in fruits and the negative impacts they cause on multiple ecosystems. In response, there is a growing need for safe, effective, green, and sustainable disease control technologies. Bionanocomposites, with their unique ability to combine nanomaterials and biopolymers that have attractive properties, represents a promising alternative for postharvest disease control. These technologies allow for the development of functional coatings and films with antimicrobial, antioxidant, and barrier properties, which are critical for extending shelf life and preserving fruit quality. Recent advances have demonstrated that integrating nanoparticles, such as ZnO, TiO₂, Ag, and chitosan-based nanosystems, into biopolymeric matrices, like alginate, pectin, starch, or cellulose, can enhance mechanical strength, regulate gas exchange, and control the release of active agents. This review presents systematized information that is focused on the creation of coatings and films based on bionanocomposites for the management of disease in fruits and vegetables. It also discusses the use of diverse biopolymers and nanomaterials and their impact on the quality and shelf life of fruits and vegetables. Full article

This study developed cholesteric liquid crystal broadband reflective films using zinc oxide nanoparticles (ZnO NPs) and homotriazine UV-absorbing dye (UV-1577) to enhance infrared shielding. Unlike benzotriazole-based UV absorber UV-327, which suffers from volatility and contamination, UV-1577 exhibits superior compatibility with liquid crystals, higher UV absorption efficiency, and enhanced processing stability due to its larger molecular structure. By synergizing UV-1577 with ZnO NPs, we achieved a gradient UV intensity distribution across the film thickness, inducing a pitch gradient that broadened the reflection bandwidth to 915 nm and surpassing the performance of previous systems using UV-327/ZnO NPs (<900 nm). We conducted a detailed examination of the factors influencing the reflective bandwidth. These included the UV-1577/ZnO NP ratio, the concentrations of the polymerizable monomer (RM257) and chiral dopant (R5011), along with polymerization temperature, UV irradiation intensity, and irradiation time. The resultant films demonstrated efficient ultraviolet shielding via the UV-1577/ZnO NPs collaboration and infrared shielding through the induced pitch gradient. This work presents a scalable strategy for energy-saving smart windows. Full article

Inkjet printing has become a primary technique for manufacturing flexible and conformal electronics due to its digital control, design flexibility, and material compatibility. However, its direct deposition nature results in weak adhesion between metal films and substrates, as it mainly relies on van der Waals or capillary forces, which severely limits its broader application in these fields. To address this limitation, we proposed an additive–subtractive manufacturing method based on a water-soluble sacrificial layer. First, the sacrificial material is inkjet-printed onto the substrate. Then, ion sputtering is employed to bombard the surface with high-energy ions, enabling metal atoms to embed into the substrate and form a strongly adhered conductive layer. Finally, the substrate is immersed in water, dissolving the sacrificial layer and detaching the undesired metal, thereby achieving selective retention of the conductive pattern. Experimental results demonstrate that the optimized water-soluble material, with tailored viscosity and surface tension, enables a patterning resolution of ±10 μm. The adhesion strength of the sputtered metal layer is 5.2 times greater than that of inkjet-printed silver nanoparticles. This method was further applied to fabricate conductive patterns on a curved surface with a 91 mm radius confirming its feasibility and adaptability for complex 3D surfaces. Full article

This study reports a gate-tunable three-terminal optoelectronic synaptic device based on an Al/ZnO nanoparticles (NPs)/SiO₂/Si structure for neuromorphic in-sensor memory applications. The ZnO NP film, fabricated via spin coating, exhibited strong UV-induced excitatory post-synaptic current (EPSC) responses that were modulated by gate voltage through charge injection across the SiO₂ dielectric rather than by conventional field effect. Optical stimulation enabled short-term synaptic plasticity, with paired-pulse facilitation (PPF) values reaching 185% at a gate voltage of −5.0 V and decreasing to 180% at +5.0 V, confirming gate-dependent modulation of synaptic weight. Repeated stimulation enhanced learning efficiency and memory retention, as demonstrated by reduced pulse numbers for relearning and slower EPSC decay. Wickelgren’s power law analysis further revealed a decrease in the forgetting rate under negative gate bias, indicating improved long-term memory characteristics. A 3 × 3 synaptic device array visualized visual memory formation through EPSC-based color mapping, with darker intensities and slower fading observed under −5.0 V bias. These results highlight the critical role of gate-voltage-induced charge injection through the SiO₂ dielectric in controlling optical potentiation and electrical depression, establishing ZnO NP-based optoelectronic synaptic devices as promising platforms for energy-efficient, light-driven neuromorphic computing. Full article

Highly heat-resistant and low-dielectric materials are crucial for achieving high-frequency communication, high-density integration, and high-temperature stability in modern electronics. In this work, surface modification of hollow silica microspheres (HGMs) using a silane coupling agent ((3-aminopropyl)triethoxysilane, KH550) yielded KHGM particles with a coating content of approximately 9.3 wt%, which were subsequently incorporated into high-performance polyarylene ether nitrile (PEN) polymers to fabricate composite films. The modified nanoparticles demonstrated significantly enhanced compatibility with the polymer matrix, while their hollow structure effectively reduced the dielectric constant of the composite film. When loaded with 50 wt% KHGM particles, the PEN-based composite film exhibited an elevated glass transition temperature of 198 °C and achieved a dielectric constant as low as 2.32 at 1 MHz frequency, coupled with dielectric loss below 0.016; compared with pure PEN, the dielectric constant of PEN/KHGM-50% decreased by 26.47%. Additionally, the composite demonstrated excellent water repellency. These advancements provide high-performance material support for applications in electronic communications, aerospace, and related fields. Full article

In this work, κ-carrageenan (κ-C) and polyethylene oxide (PEO) were utilized to synthesize polymeric films (κ-C-PEO). A 2^k experimental design was employed to optimize the synthesis of κ-C-PEO systems by considering the content of κ-carrageenan, PEO, and glycerin and their influence on the mechanical features of the resultant films. The κ-C-PEO systems were robustly characterized by FTIR spectroscopy, thermogravimetric analyses, and scanning electron microscopy (SEM). Magnesium oxide nanoparticles (MgO-NPs) were utilized to load κ-C-PEO films as an efficient approach to enhance their biological performance. The activity of κ-C-PEO films was studied against Gram-negative bacteria through the Kirby–Bauer assay. Artemia salina nauplii were cultured to assess the possible toxicity of κ-C-PEO films. The results demonstrated that κ-C-PEO films were elongated with the heterogeneous distribution of MgO-NPs. The tensile strength, thickness, and swelling capacity of κ-C-PEO films were 129 kPa, 0.19 mm, and 52.01%, respectively. TGA and DTA analyses revealed that κ-C-PEO films are thermally stable structures presenting significant mass loss patterns at >200 °C. Treatment with κ-C-PEO films did not inhibit the growth of Escherichia coli nor Pseudomonas aeruginosa. Against A. salina nauplii, κ-C-PEO films did not decrease the survival rate nor compromise the morphology of the tested in vivo model. The retrieved data from this study expand the knowledge about integrating inorganic nanomaterials with polysaccharide-based structures and their possible application in treating chronic wounds. Even though this work provides innovative insights into the optimal design of bioactive structures, further approaches are required to improve the biological performance of the synthesized κ-C-PEO films. Full article

The growing need for sustainable packaging materials with enhanced functionality has prompted our investigation into biodegradable polymers reinforced with nanostructures. In this work, we began by extracting anthocyanins from pigmented native potatoes (Solanum tuberosum) and confirming their concentration via UV–Visible spectroscopy. The corresponding potato starch was then characterized according to its amylose and amylopectin contents. The natural pigments subsequently served as reducing and stabilizing agents in a green synthesis of silver nanoparticles (AgNPs), which were subsequently incorporated into starch matrices derived from the same tuber. To evaluate the performance of the resulting composite films, we examined their pH-responsive color behavior—demonstrating their potential as visual indicators—their molecular structure through FTIR analysis—to verify the successful integration of AgNPs—and their moisture content as a measure of barrier properties. The AgNP-containing films exhibited markedly improved color stability across varying pH levels and superior moisture retention compared to pure starch films. These results illustrate the promise of combining underutilized Andean crops with eco-friendly nanotechnology to produce advanced, biodegradable materials suitable for intelligent food-packaging applications. Full article

Synthetic opal-based photonic materials with tunable optical properties not only exhibit significant application potential but also provide valuable models in terms of understanding color formation mechanisms in natural gemstones. Inspired by natural fire opals containing small amounts of Fe₂O₃ nanoparticle inclusions (0 wt%~0.23 wt%), we fabricated short-range ordered opal films doped with low concentrations (0 wt%~2.00 wt%) of Fe₂O₃@SiO₂ core–shell nanoparticles using a modified vertical deposition method. The Fe₂O₃@SiO₂ nanoparticles were synthesized via a sol–gel process to encapsulate the Fe₂O₃ core with a 10-nm-thick SiO₂ shell, preventing agglomeration and enhancing the chemical stability. Experimental results show that even small amounts of doping significantly affect the reflection peak intensity of the films, leading to notable color appearance changes. Combined with numerical simulations, we attribute this modulation to both light absorption and backward scattering effects introduced by the doped nanoparticles. Moreover, the numerical simulation results for Fe₂O₃ nanoparticles and Fe₂O₃@SiO₂ nanoparticles (with a 10 nm silica shell and similar particle size) show comparable optical properties, suggesting that such inclusions may contribute similarly to the color formation mechanisms in natural fire opals. This work demonstrates that low-concentration Fe₂O₃@SiO₂ NP doping provides an effective strategy to tune the color appearance of opal films, with implications for both structural color material development and gemological research. Full article

Polymer coatings as thin films stand out as a commonly used strategy to modify biosensor surfaces for improving detection performance; however, nonspecific biomolecule interactions and the limited degree of ligand conjugation on the surface have necessitated the development of innovative methods for surface modification. To this end, methacrylated tethered telechelic polyethylene glycol (PEG-diMA) chains of three different molecular weights (2, 6, and 10 kDa) were synthesized herein and used for obtaining thiolated nanoparticles (NPs) upon adding excess amounts of a tetra-thiol crosslinker. Characterized according to their size, surface charge, morphology, and thiol amounts, these nanoparticles were immobilized on gold surfaces that mimicked gold-coated mass sensor platforms. The PEG-based nanoparticles, prepared especially by PEG6K-diMA polymers, were shown to result in the preparation of a monolayer and smooth coating of 80–120 nm thickness. Cysteine-modified NTS(8–13) peptide (RRPYIL) was conjugated to thiolated NP with reversible disulfide bonds and it was demonstrated that its cleavage with a reducing agent such as dithiothreitol (DTT) restores the NP-immobilized gold surface for at least two cycles. Together with its binding studies to NTSR2 antibodies, it was revealed that the peptide-conjugated NP-modified gold surface could be employed as a model for a reusable sensor surface for the detection of biomarkers of same or different types. Full article

This study reports on the fabrication of chitosan-zein films decorated with silver nanoparticles synthesized via a green and eco-friendly approach using an extract of Bergenia ciliata. The strong reducing ability and caping properties of the phytochemicals present in the extract enabled the formation of silver nanoparticles with an average diameter of ~40 nm without any external reducing agent and stabilizer. The uniformly distributed Ag nanoparticles were embedded in the chitosan-zein matrix. The structural and morphological characteristics of the film were analyzed via Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray diffractometry, scanning electron microscopy, and transmission electron microscopy. The silver nanoparticles decorated with chitosan-zein films showed thermal stability, durability, and excellent antimicrobial activities. This finding demonstrates a sustainable and green pathway for developing multifunctional nanocomposite films, contributing to the advancement of bio-based materials for prospective therapeutic applications and active food packaging. Full article