Search Results (684)

Chlorobenzoic acids (CBAs) are a group of chlorinated persistent environmental pollutants with hard biodegradability, high water solubility, and well-documented carcinogenic and endocrine-disrupting properties. Electrocatalytic hydrodechlorination (ECH) is a highly efficient method under mild conditions without harmful by-products, but the ECH process commonly requires adding precious metal catalysts such as palladium (Pd). To address the economic constraints and more effective utilization of Pd, a palladium/manganese dioxide (Pd/MnO₂) composite catalyst was developed in this study by chemical deposition. This method utilized the excellent electrochemical activity of MnO₂ as a carrier as well as the hydrogen storage and activation capacity of Pd. The test showed the optimal Pd loading was 7.5%, and the removal percent of 2,4-dichlorobenzoic acid (2,4-DCBA), a typical CBA, reached 97.3% using 0.5 g/L of Pd/MnO₂ after 120 min of electrochemical reaction. Under these conditions, the dechlorination percent can also be as high as 89.6%. A higher current density enhanced the dechlorination efficiency but showed the lower current utilization efficiency. In practical applications, current density should be minimized on the premise of compliance with the water treatment requirement. Mechanistic studies showed that MnO₂ synergistically promoted hydrolysis dissociation and hydrogen spillover and facilitated Pd-mediated adsorption of atomic hydrogen (H*) for dehydrogenation of 2,4-DCBA. The presence of MnO₂ can effectively disperse the loaded Pd and reduce the amount of Pd via the above process. The catalyst exhibited excellent stability over multiple cycles, and the 2,4-DCBA removal could still reach more than 80% after the five cycles. This work establishes electrocatalytic strategies for effectively reducing Pd usage and maintaining high removal of typical CBAs to support CBA-related water treatment. Full article

The design of sustainable nanomaterials for catalysis is a key challenge in green chemistry. Herein, we report the synthesis of halloysite nanotube (Hal)-based nanomaterials selectively functionalized with a bio-inspired polydopamine (PDA) coating, which enables the controlled anchoring of palladium and copper nanoparticles (PdNPs and CuNPs). This mild and ecofriendly strategy yields highly dispersed and ultrasmall (<5 nm) metal nanoparticles without the need for surfactants or harsh reagents. The resulting materials, Hal@PDA/PdNPs and Hal@PDA/CuNPs, were evaluated in two well-established model reactions commonly employed to probe catalytic performance: cinnamaldehyde hydrogenation and 4-nitrophenol reduction. Hal@PDA/PdNPs displayed complete conversion and >90% selectivity toward hydrocinnamaldehyde at low Pd loading (0.8 wt%) and maintained its efficiency over six catalytic cycles (TOF up to 0.1 s⁻¹), while Hal@PDA/CuNPs retained high activity through eight consecutive runs in the reduction of 4-nitrophenol. Hal@PDA/CuNPs proved to be an excellent recyclable catalyst for the reduction of 4-nitrophenol, retaining high activity through eight consecutive runs. Overall, this study introduces a robust and modular approach to fabricating halloysite-based nanocatalysts, demonstrating their potential as green platforms for metal nanoparticle-mediated transformation. Full article

The oxygen evolution reaction (OER) is a kinetic bottleneck in electrochemical water splitting, creating an urgent need for the development of efficient electrocatalysts. Prussian blue analogues (PBAs), a significant class of inorganic coordination polymers, have emerged as excellent precursors and pre-catalysts for preparing various OER nanocatalysts, owing to their numerous advantages such as tunable composition, controllable morphology, and structural derivability. This review systematically summarizes recent advances in PBA-based OER electrocatalysts, beginning with two core strategies: enhancing active site accessibility and utilization, and improving the intrinsic activity of each active site. We provide an in-depth discussion of the design principles for enhancing active site accessibility and utilization through constructing porous architectures, creating hierarchical porosity, and improving electrical conductivity. The review also details key approaches for improving intrinsic activity, including regulating electronic structure via elemental doping and optimizing active sites via defect engineering, while examining the underlying mechanisms for performance enhancement. Finally, current challenges and future research directions are outlined, offering a perspective on the potential applications of PBA-based catalysts in sustainable energy conversion systems. Full article

The growing demand for sustainable and efficient synthetic methodologies has brought nanocatalysis to the forefront of modern organic chemistry, particularly in the construction of heterocyclic compounds through multicomponent reactions (MCRs). Among various nanocatalysts, calcium oxide nanoparticles (CaO NPs) have gained significant attention because of their strong basicity, thermal stability, low toxicity, and cost-effectiveness. This review provides a comprehensive account of the recent strategies using CaO NPs as heterogeneous catalysts for the green synthesis of nitrogen- and oxygen-containing heterocycles through MCRs. Key reactions such as Biginelli, Hantzsch, and pyran annulations are discussed in detail, with emphasis on atom economy, reaction conditions, product yields, and catalyst reusability. In many instances, CaO NPs have enabled solvent-free or aqueous protocols with high efficiency and reduced reaction times, often under mild conditions. Mechanistic aspects are analyzed to highlight the catalytic role of surface basic sites in facilitating condensation and cyclization steps. The performance of CaO NPs is also compared with other oxide nanocatalysts, showcasing their benefits from green metrics evaluation like E-factor and turnover frequency. Despite significant progress, challenges remain in areas such as asymmetric catalysis, industrial scalability, and catalytic stability under continuous use. To address these gaps, future directions involving doped CaO nanomaterials, hybrid composites, and mechanochemical approaches are proposed. This review aims to provide a focused and critical perspective on CaO NP-catalyzed MCRs, offering insights that may guide further innovations in sustainable heterocyclic synthesis. Full article

Binary metallic nickel–copper nanocatalysts were anchored onto a polyvinylidene fluoride-co-hexafluoropropylene membrane [NiCu/PVdF–HFP] using the electrospinning technique, followed by the chemical reduction of the relevant precursor salts by introducing sodium borohydride to the synthesis mixture. A series of varied Ni:Cu weight % proportions was developed in order to optimize the electroactivity of this binary nanocomposite towards the investigated oxidation process. A number of physicochemical tools were used to ascertain the morphology and chemical structure of the formed metallic species on polymeric films. Cyclic voltammetric studies revealed a satisfactory performance of altered NiCu/PVdF–HFP membranes in alkaline solution. Ethylene glycol molecules were successfully electro-oxidized at their surfaces, showing the highest current intensity [564.88 μA cm⁻²] at the one with Ni:Cu weight ratios of 5:5. The dependence of these metallic membranes’ behavior on the added alcohol concentration to the reaction electrolyte and the adjusted scan rate during the electrochemical measurement was carefully investigated. One hundred repeated scans did not significantly deteriorate the NiCu/PVdF–HFP nanostructures’ durability. Decay percentages of 76.90–87.95% were monitored at their surfaces, supporting the stabilized performance for prolonged periods. A much-decreased R_ct value was estimated at Ni₅Cu₅/PVdF–HFP [392.6 Ohm cm²] as a consequence of the feasibility of the electron transfer step for the electro-catalyzing oxidation process of alcohol molecules. These enhanced study results will hopefully motivate the interested workers to explore the behavior of many binary and ternary combinations of metallic nanomaterials after their deposition onto convenient polymeric films for vital electrochemical reactions. Full article

Achieving ultra-low-sulfur diesel is a crucial objective in modern fuel refining, driven by increasingly stringent environmental regulations. This study presents the development of a highly efficient oxidative–adsorptive desulfurization process utilizing a nanocatalyst synthesized from biowaste eggshell-extracted calcite. The oxidation reaction was conducted in a digital basket reactor (DBR), an advanced reactor system designed to enhance mass transfer and catalytic efficiency. To further augment the catalyst’s performance, the calcite was modified with eco-friendly MnO₂, while activated carbon was employed as an adsorbent to effectively capture oxidized sulfur compounds, ensuring compliance with ultra-low-sulfur fuel standards. The synthesized nanocatalyst underwent comprehensive physicochemical characterization using SEM, EDX, BET, and FTIR, confirming its high surface area, structural integrity, and superior catalytic activity. The MnO₂/P–calcite catalyst achieved a sulfur removal efficiency of 96.5% at 90 °C, 80 min, and 600 rpm, demonstrating excellent oxidative–adsorptive performance for real diesel fuel. The integration of this innovative nanocatalyst with the DBR system presents a sustainable, cost-effective, and industrially viable approach for deep desulfurization, offering significant advancements in clean fuel production and environmental sustainability. Full article

The growing accumulation of waste lubricating oil presents serious environmental issues, calling for sustainable management solutions. This research discusses the creation of FeNi/TiO₂ nanocatalysts that were synthesized through an eco-friendly method utilizing grape seed extract (GSE) as a natural reducing agent for the catalytic pyrolysis of waste lubricating oil. The nanocatalyst was produced using the microemulsion technique and refined via Response Surface Methodology (RSM) to optimize its catalytic performance. Pyrolysis was carried out at 400 °C, leading to a significant conversion of waste oil into valuable fuel. The FeNi/TiO₂ nanocatalyst exhibited exceptional capabilities in facilitating the breakdown of heavy hydrocarbons into lighter fuel fractions while reducing unwanted byproducts. GC-MS analysis demonstrated the prevalence of C6–C20 hydrocarbons in the pyrolysis oil, underscoring its potential as a high-quality alternative fuel similar to traditional diesel. This study aids in the progress of environmentally sustainable waste-to-energy technologies, offering a promising pathway for effective fuel production and hazardous waste management. Full article

In industrial processes, catalysts—materials that speed up chemical reactions without being consumed—are essential. The goal of this research was to create two new rhenium-based nanocomposite catalysts that can effectively and sustainably reduce nitroaromatic compounds to aromatic amines in continuous-flow systems. Nitroaromatic hydrocarbons (NACs), widely used in manufacturing pharmaceuticals, insecticides, and herbicides, often contaminate soil and water, posing significant environmental and health risks. However, their reduction to aromatic amines enables potential industrial reuse. In this study, we synthesized two nanocomposite catalysts based on a copolymer functionalized with N-methyl-D-glucamine, embedded with rhenium (Re)-based apparent nanoparticles, and used them to reduce the NACs in continuous-flow mode to their aromatic amines using newly designed and stereolithographic (SLA) 3D-printed reactors. Advanced characterization techniques were employed to evaluate their structure, morphology, and catalytical performance. Catalyst 1, prepared from a self-modified Purolite D4869 resin and characterized by higher Re loading, exhibited superior conversion rates in batch mode (k₁ up to 1.406 s⁻¹). In contrast, Catalyst 2, based on a commercial NMDG-functionalized Dowex resin with a mesoporous structure, demonstrated remarkable stability and catalytic capacity under continuous flow (up to 1.383 mmol_NAC mL_cat⁻¹). Overall, Catalyst 1 was found to be better suited for rapid batch reactions, whereas Catalyst 2 was found to be more appropriate for long-term flow applications, offering a sustainable route for the efficient conversion of nitroaromatic compounds into valuable aromatic amines. The reactors enabled the efficient conversion of NACs into aromatic amines while enhancing process sustainability and efficiency. Full article

The development of effective catalysts for the oxygen reduction reaction (ORR) is crucial for improving the performance of fuel cells. Efficient carbon-supported Pt-Co nanocatalysts were successfully prepared by a generic two-step method: (i) electroless deposition of a Co-P coating on Vulcan XC72R carbon powder and (ii) subsequent spontaneous partial galvanic replacement of Co by Pt, upon immersion of the Co/C precursor in a chloroplatinate solution. The prepared Pt-Co particles (of a core-shell structure) are dispersed on a Vulcan XC-72 support, forming agglomerates made of nanoparticles smaller than 10 nm. The composition and surface morphology of the samples were characterized by scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM/EDS) as well as transmission electron microscopy (TEM). The crystal structures of the Co-P/C precursor and Pt-Co/C catalyst were investigated by X-ray diffraction (XRD). XPS analysis was performed to study the chemical state of the surface layers of the precursor and catalyst. The electrochemical behavior of the Pt-Co/C composites was evaluated by cyclic voltammetry (CV). Linear sweep voltammetry (LSV) experiments were used to assess the catalytic activity towards the ORR and compared with that of a commercial Pt/C catalyst. The Pt-Co/C catalysts exhibit mass-specific and surface-specific activities (of j_m = 133 mA mg⁻¹ and j_esa = 0.661 mA cm⁻², respectively) at a typical overpotential value of 380 mV (+0.85 V vs. RHE); these are superior to those of similar electrodes made of a commercial Pt/C catalyst (j_m = 50.6 mA mg⁻¹; j_esa = 0.165 mA cm⁻²). The beneficial effect of even small (<1% wt.%) quantities of Co in the catalyst on Pt ORR activity may be attributed to an optimum catalyst composition and particle size resulting from the proposed preparation method. Full article

This study explores the use of a novel heterogeneous CoZnFe₄O₈ nanocatalyst for biodiesel production from a sustainable and innovative blend of waste cooking oil and neem oil feedstock. Utilizing waste cooking oil and inedible neem oil feedstock to produce biodiesel provides a green and economical way to produce renewable and environmentally friendly fuel while simultaneously reducing waste and valorizing inedible oils. Additionally, this feedstock blend does not threaten food or land resources as opposed to feedstocks obtained from edible resources. To fulfill the rising demand for biodiesel and address issues related to lower ester yields, particularly when utilizing waste cooking oils with high free fatty acid concentration, there is an urgent need for more effective processes, including two-stage transesterification. The novel CoZnFe₄O₈ nanocatalyst employed in this study demonstrated high efficiency in biodiesel production thanks to its high surface area, mesoporous structure, and catalytic properties. The effect of key process parameters, including catalyst concentration, reaction time, alcohol-to-oil molar ratio, and oil blend ratio, was investigated to evaluate the performance of the nanocatalyst and optimize the biodiesel yield with the help of Response Surface Methodology (RSM). The optimized process achieved a yield of 94.23% under optimum parameters of 2.13 wt% catalyst, 6.80:1 methanol-to-oil ratio, 4 h, and a ratio of waste cooking oil to neem oil of 98.32:1.68. The predicted and experimental values were in close agreement, indicating that the model was adequate. Additionally, detailed catalyst characterization, including analysis of the surface area, structure, and thermal stability, was carried out. Similarly, the biodiesel was characterized to assess its quality through heating value, density, Fourier Transform Infrared (FTIR) spectroscopy, and ultimate analysis. The recovery and reusability of the nanocatalyst were also investigated, highlighting its potential for multiple reaction cycles. The novel CoZnFe₄O₈ nanocatalyst and innovative feedstock blend demonstrated high efficiency in biodiesel production comparable to other nanocatalysts and feedstocks reported in the literature, highlighting their potential as an efficient and sustainable method to produce biofuels. Full article

In response to the ongoing challenges associated with natural enzymes, their high production costs, low stability and limited functionality; nanozymes have rapidly emerged as versatile alternative. Such nanocatalysts, based on nanomaterials and nanostructures, offer remarkable tunability of physicochemical properties and excellent durability, and adapt themselves effectively to the requirements of modern biotechnological applications. This review article aims to provide a comprehensive overview of recent advances in the use of naturally occurring iron oxide nanoparticles, produced by magnetotactic bacteria, and to highlight their emerging role as key elements in the development of the new generation of nano-guided biosensors. It provides a comprehensive and systematic analysis of publications in the Web of Science database between 2022 and August 2025, conducted in accordance with PRISMA guidelines. The aim was to assess the current state of the art and identify knowledge gaps in the exploration and application of magnetotactic bacteria as natural and sustainable sources in the design of next-generation biosensors. The natural nanoparticles, formed through biological processes, represent a unique and sustainable alternative to synthetic nanoparticles, offering naturally mimetic enzymatic activity, high biocompatibility, and exceptional stability. This approach opens up revolutionary perspectives in the field of biosensors, proposing a new class of functional materials, iron nanoparticles of biological origin, capable of fundamentally changing the performance, sustainability and reliability of future nanoenzymatic sensing platforms. Full article

The sustainable development of our society faces significant challenges, including the need for environmentally friendly energy storage devices. Our work is concerned with the conversion of Mo-based recycled industrial waste into active nanocatalysts for energy storage applications. To reach this goal, we employed hydrothermal synthesis, a low-cost and temperature-scalable method. The proposed synthesis produces MoO₃ nanobelts (50–200 nm in width and 2–5 µm in length) with a high yield, about 74%. The synthesized nanostructures were characterized in 1 M KOH and 1 M NH₄OH, as alkaline environments are a promising choice for the development of eco-friendly devices. To investigate the material’s behaviour cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), and electrochemical impedance spectroscopy (EIS) measurements were carried out. From CV curves, it was possible to evaluate the specific capacitance values of 290 and 100 Fg⁻¹ at 5 mVs⁻¹ in 1 M KOH and 1 M NH₄OH, respectively. Also, GCD was employed to evaluate the specific capacitance of the material, resulting in 75 and 60 Fg⁻¹ in 1 M KOH and 1 M NH₄OH, respectively. CV and GCD analyses revealed that MoO₃ nanobelts act as two different types of energy storage devices: supercapacitors and pseudocapacitors. Additionally, EIS allowed us to distinguish between the resistive and capacitive behaviour contributions depending on the electrolyte. Furthermore, it provided a comprehensive electrochemical characterization in different alkaline electrolytes, with the intention of conjugating waste management and sustainable energy storage device production. Full article

The development of heterogeneous nanocatalysts with high performance is essential for improving hydrogen production through formic acid dehydrogenation, but challenging. Herein, highly dispersed Pd nanoparticles (NPs) were successfully immobilized on porous nitrogen-doped carbon cages (PNCCs) derived from zeolitic imidazole frameworks. By virtue of the synergistic effect, the optimized Pd/PNCC nanocatalytic systems exhibit an excellent catalytic kinetics toward catalyzing FA dehydrogenation with a turnover frequency (TOF) value as high as 3174 h⁻¹ at 323 K, which is 59 times relative to that of Pd nanoparticles. The exceptional activity may be ascribed to the PNCC solid support may induce a strong electronic metal–support interaction to optimize the electron configuration of Pd active sites and accelerate the kinetics of O-H bond cleavage, resulting in an enhanced catalytic performance toward FA dehydrogenation. This work will supply a novel strategy for the development of supported nanocatalysts with high performance for tremendous catalytic applications in the future. Full article

This work focuses on the sustainable green synthesis of magnetic iron oxide nanoparticles (Fe₃O₄NPs) using bioreductants derived from orange peel extracts for application in the efficient oxygen evolution reactions (OER). The synthesized catalysts were characterized using X-ray diffraction analysis, field emission scanning electron microscopy (FESEM), energy dispersive X-ray analysis (EDS), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), and UV–visible spectroscopy. The Fe₃O₄NPs exhibit a well-defined spherical morphology with a larger Brunauer–Emmett–Teller surface area and a significant electrochemically active surface area. The green synthesis using orange peel extracts leads to an excellent electrocatalytic activity of the apparent spherical Fe₃O₄NPs (diameter of 9.62 ± 0.07 nm), which is explored for OER in an alkaline medium (1.0 M KOH) using linear-sweep and cyclic voltammetry techniques. These nanoparticles achieved a benchmark current density of 10 mA cm⁻² at a low overpotential of 0.3 V versus RHE, along with notable durability and stability. The outstanding OER electrocatalytic activity is attributed to their unique morphology, which offers large surface area and an ideal porous structure that enhances the adsorption and activation of reactive species. Furthermore, structural defects within the nanoparticles facilitate efficient electron transfer and migration of these species, further accelerating the OER process. Full article

The development of highly efficient catalysts for the hydrogenation of dicyclopentadiene (DCPD) remains a critical challenge. In this study, we designed a series of bimetallic Ce–Ni metal–organic framework (MOF)-derived nanocatalysts by precisely tuning the Ce/Ni ratio and calcination temperatures. The optimized catalyst, Ni–CeO_2(7:3) @C–400 °C, featuring highly dispersed carbon-coated Ni nanoparticles, achieved complete hydrogenation of DCPD to tetrahydrodicyclopentadiene (THDCPD) with 100% conversion and nearly 100% selectivity within 2 h under 100 °C and 2 MPa. The porous carbon framework significantly facilitated the diffusion and accessibility of DCPD molecules, combined with Ce species reconstructing the electronic structure of Ni active centers through electronic interactions, synergistically enhancing the hydrogenation efficiency. Furthermore, the catalyst demonstrated good structural stability. This work not only provides a robust strategy for the rational design of bimetallic MOF-derived catalysts but also highlights their potential for practical applications in industrial hydrogenation processes. Full article