Search Results (841)

Municipal wastewaters pose a severe risk to the environment and human health when discharged untreated. This is due to their high content of pathogens, such as viruses and bacteria, which can cause diseases like cholera. Herein, the research and development of porphyrin-modified polyethersulfone (PES) ultrafiltration (UF) membranes was conducted to improve bacterial inactivation in complex municipal wastewater and enhance the fouling resistance and filtration performance. The synthesis and fabrication of porphyrin nanofillers and the resultant membrane characteristics were studied. The incorporation of porphyrin-based nanofillers improved the membrane’s hydrophilicity, morphology, and flux (247 Lm⁻² h⁻¹), with the membrane contact angle (CA) decreasing from 90° to ranging between 58° and 50°. The membrane performance was monitored for its flux, antifouling properties, reusability potential, municipal wastewater, and humic acid. The modified membranes demonstrated an effective application in wastewater treatment, achieving notable antibacterial activity, particularly under light exposure. The In-BP@SW/PES membrane demonstrated effective antimicrobial photodynamic effects against both Gram-positive S. aureus and Gram-negative E. coli. It achieved at least a 3-log reduction in bacterial viability, meeting Food and Drug Administration (FDA) standards for efficient antimicrobial materials. Among the variants tested, membranes modified with In-PB@SW nanofillers exhibited superior antifouling properties with flux recovery ratios (FRRs) of 78.9% for the humic acid (HA) solution and 85% for the municipal wastewater (MWW), suggesting a strong potential for long-term filtration use. These results highlight the promise of porphyrin-functionalized membranes as multifunctional tools in advanced water treatment technologies. Full article

This study evaluates the potential use of reclaimed sand from municipal wastewater treatment plants (WWTP), categorized as waste under code 19 08 02, as a full substitute for natural sand in cement mortars. The sand was subjected to alkaline pretreatment using sodium hydroxide (NaOH) at concentrations of 0.5%, 1% and 2% to reduce organic impurities and improve surface cleanliness. All mortar mixes were prepared using CEM I 42.5 R as the binder, maintaining a constant water-to-cement ratio of 0.5. Mechanical testing revealed that mortars produced with 100% WWTP-derived sand, pretreated with 0.5% NaOH, achieved a mean compressive strength of 51.9 MPa and flexural strength of 5.63 MPa after 28 days, nearly equivalent to reference mortars with standardized construction sand (52.7 MPa and 6.64 MPa, respectively). In contrast, untreated WWTP sand resulted in a significant performance reduction, with compressive strength averaging 30.0 MPa and flexural strength ranging from 2.55 to 2.93 MPa. The results demonstrate that low-alkaline pretreatment—particularly with 0.5% NaOH—allows for the effective reuse of WWTP waste sand (code 19 08 02) in cement mortars based on CEM I 42.5 R, achieving performance comparable to conventional materials. Although higher concentrations, such as 2% NaOH, are commonly recommended or required by standards for the removal of organic matter from fine aggregates, the results suggest that lower concentrations (e.g., 0.5%) may offer a better balance between cleaning effectiveness and mechanical performance. Nevertheless, 2% NaOH remains the obligatory reference level in some standard testing protocols for fine aggregate purification. Full article

In response to the European Union’s revised Urban Wastewater Treatment Directive, which mandates enhanced monitoring and advanced treatment of micropollutants, this study was conducted. It took place within the Coastal Landscape Park (CLP), a Natura 2000 protected area in northern Poland. The focus was on the municipal wastewater treatment plant in Jastrzębia Góra, located in a region exposed to seasonal tourist pressure and discharging effluent into the Czarna Wda River. A total of 90 wastewater samples were collected during five monitoring campaigns (July, September 2021; February, May, July 2022) and analysed for 13 pharmaceuticals and personal care products (PPCPs) using ultra-high-performance liquid chromatography tandem mass spectrometry with electrospray ionisation (UHPLC-ESI-MS/MS). The monitoring included both untreated (UTWW) and treated wastewater (TWW) to assess the PPCP removal efficiency and persistence. The highest concentrations in the treated wastewater were observed for metoprolol (up to 472.9 ng/L), diclofenac (up to 3030 ng/L), trimethoprim (up to 603.6 ng/L) and carbamazepine (up to 2221 ng/L). A risk quotient (RQ) analysis identified diclofenac and LI-CBZ as priority substances for monitoring. Multivariate analyses (PCA, HCA) revealed co-occurrence patterns and seasonal trends. The results underline the need for advanced treatment solutions and targeted monitoring, especially in sensitive coastal catchments with variable micropollutant presence. Full article

With increasing global challenges related to water scarcity and phosphorus depletion, the recovery and reuse of wastewater-derived nutrients offer a sustainable path forward. This study evaluates the dual role of lanthanides (Ce³⁺ and La³⁺) in recovering phosphorus from municipal wastewater and supporting corn (Zea mays) cultivation through lanthanide phosphate (Ln-P) and lanthanide-reclaimed wastewater (LRWW, wastewater spiked with lanthanide). High-purity precipitates of CePO₄ (98%) and LaPO₄ (92%) were successfully obtained without pH adjustment, as confirmed by X-ray photoelectron spectroscopy (XPS) and energy-dispersive spectroscopy (EDS). Germination assays revealed that lanthanides, even at concentrations up to 2000 mg/L, did not significantly alter germination rates compared to traditional coagulants, though root and shoot development declined above this threshold—likely due to reduced hydrogen peroxide (H₂O₂) production and elevated total dissolved solids (TDSs), which induced physiological drought. Greenhouse experiments using desert-like soil amended with Ln-P and irrigated with LRWW showed no statistically significant differences in corn growth parameters—including plant height, stem diameter, leaf number, leaf area, and biomass—when compared to control treatments. Photosynthetic performance, including stomatal conductance, quantum efficiency, and chlorophyll content, remained unaffected by lanthanide application. Metal uptake analysis indicated that lanthanides did not inhibit phosphorus absorption and even enhanced the uptake of calcium and magnesium. Minimal lanthanide accumulation was detected in plant tissues, with most retained in the root zone, highlighting their limited mobility. These findings suggest that lanthanides can be safely and effectively used for phosphorus recovery and agricultural reuse, contributing to sustainable nutrient cycling and aligning with the United Nations’ Sustainable Development Goals of zero hunger and sustainable cities. Full article

Ozonation and ozone-based advanced oxidation processes, including ozone/hydrogen peroxide and ozone/ultraviolet irradiation, have been extensively studied for their efficacy in treating wastewater across various industries. While sectors such as pulp and paper, textile, food and beverage, microelectronics, and municipal wastewater have successfully implemented ozone at full scale, others have yet to fully embrace these technologies’ effectiveness. This review article examines recent publications from the past two decades, exploring novel applications of ozone-based technologies in treating wastewater from diverse sectors, including food and beverage, agriculture, aquaculture, textile, pulp and paper, oil and gas, medical and pharmaceutical manufacturing, pesticides, cosmetics, cigarettes, latex, cork manufacturing, semiconductors, and electroplating industries. The review underscores ozone’s broad applicability in degrading recalcitrant synthetic and natural organics, thereby reducing toxicity and enhancing biodegradability in industrial effluents. Additionally, ozone-based treatments prove highly effective in disinfecting pathogenic microorganisms present in these effluents. Continued research and application of these ozonation and ozone-based advanced oxidation processes hold promise for addressing environmental challenges and advancing sustainable wastewater management practices globally. Full article

Societies are aiming to have a higher ecological consciousness in wastewater treatment operations and achieve a more sustainable future. With this said, global demands for larger quantities of resources and the consequent waste generated will inevitably lead to the exhaustion of current municipal wastewater treatment works. The utilization of biosolids (particularly microbial proteins) from wastewater treatment operations could generate a sustainable bio-adhesive for the wood industry, reduce carbon footprint, mitigate health concerns related to the use of carcinogenic components, and support a more circular economic option for wastewater treatment. A techno-economic analysis for three 10 MGD wastewater treatment operations producing roughly 11,300 dry pounds of biosolids per day, in conjunction with co-feedstock defatted soy flour protein at varying ratios (i.e., 0%, 15%, and 50% wet weight), was conducted. Aspen Capital Cost Estimator V12 was used to design and estimate installed equipment additions for wastewater treatment plant integration into an urban biorefinery process. Due to the mechanical attributes and market competition, the chosen selling prices of each adhesive per pound were set for analysis as USD 0.75 for Plant Option P1, USD 0.85 for Plant Option P2, and USD 1.00 for Plant Option P3. Over a 20-year life, each plant option demonstrated economic viability with high NPVs of USD 107.9M, USD 178.7M, and USD 502.2M and internal rates of return (IRRs) of 24.0%, 29.0%, and 44.2% respectively. The options examined have low production costs of USD 0.14 and USD 0.19 per pound, minimum selling prices of USD 0.42–USD 0.51 per pound, resulting in between 2- and 4-year payback periods. Sensitivity analysis shows the effects biosolid production fluctuations, raw material market price, and adhesive selling price have on economics. The results proved profitable even with large variations in the feedstock and raw material prices, requiring low market selling prices to reach the hurdle rate of examination. This technology is economically enticing, and the positive environmental impact of waste utilization encourages further development and analysis of the bio-adhesive process. Full article

Reverse osmosis (RO) concentrated water can be effectively treated with catalytic ozone oxidation technology, an effective advanced oxidation process. In order to provide a thorough reference for the safe treatment and reuse of RO concentrated water, this paper examines the properties of RO concentrated water, such as its high salt content, high levels of organic pollutants, and low biochemistry. It also examines the mechanism of its role in treating RO concentrated water and combs through its applications in municipal, petrochemical, coal chemical, industrial parks, and other industries. The study demonstrates that ozone oxidation technology can efficiently eliminate the organic matter that is difficult to break down in RO concentrated water and lower treatment energy consumption; however, issues with free radical inhibitor interference, catalyst recovery, and stability still affect its use. Future research into multi-technology synergistic processes, the development of stable and effective non-homogeneous catalysts, and the promotion of their use at the “zero discharge” scale for industrial wastewater are all imperative. Full article

In this paper, the production of biomass, pigments, lipids, and carbohydrates and the elimination of ammonium and orthophosphate by the microalgae Chlorella vulgaris, grown in synthetic wastewater (SWW), were studied under different light intensities (3000–10,000 lux), pH (7.5–9.5) and daily illumination time (8–16 h). The best conditions for the autotrophic culture of microalgae were predicted using response surface methodology (RSM). The results showed that the adaptation of the microalgae for this nutrient source was effective. The best conditions for the cultivation of Chlorella vulgaris in SWW were 8.44 pH and a light intensity of 8433 lux in the daily illumination time of 16 h. Under optimal conditions, the production of microalgal biomass, chlorophyll-a, chlorophyll-b, carotenoids, lipids and carbohydrates was 0.534 g/L, 7.46 mg/mL, 3.53 mg/mL, 2.01 mg/mL, 21.40% and 28.46%, respectively. The removal efficiencies of ammonium and orthophosphate from SWW were 97.66% and 58.78% in autotrophic cultures. This investigation introduces a new aspect by verifying the optimized cultivation conditions with real municipal wastewater, indicating that the procedure could be utilized for sustainable production of bioproducts and efficient treatment of municipal wastewater. Full article

Population growth has led to an increased volume of wastewater from industrial, domestic, and municipal sources, contaminating aquatic bodies in the state of Veracruz. This study aimed to assess the efficacy of a water treatment system incorporating a DAF stage, followed by the cultivation of a microalgal consortium to eliminate pollutants from the blended effluent. The cultivation of Nannochloropsis oculata in wastewater entailed the assessment of a single variable (operating pressure) within the DAF system, in conjunction with two supplementary variables (residence time and F:M ratio), resulting in removal efficiencies of 70% for CODt, 77.24% for CODs, 78.34% for nitrogen, and 77% for total organic carbon. The water sample was found to contain elevated levels of organic matter and pollutants, beyond the permitted limits set forth in NOM-001-SEMARNAT-2021. The obtained removal percentages indicate that the suggested physicochemical–biological process (DAF-microalgae) is a suitable method for treating mixed wastewater. This approach reduces atmospheric pollution by sequestering greenhouse gases such as carbon dioxide through the photosynthetic activity of N. oculata cells, so facilitating the production of oxygen and biomass while limiting their accumulation in the atmosphere. Full article

The co-disposal of municipal solid waste incineration fly ash (MSWI-FA) in cement kilns is an effective method for managing incineration by-products in China. However, the presence of heavy metals in MSWI-FA raises environmental concerns. This study analyzed the Cu, Zn, Cd, Pb, Cr, and Ni concentrations in MSWI-FA from 11 representative facilities across China and assessed the efficacy of a three-stage water washing process for Cl and heavy metal removal. The results revealed significant regional variations in heavy metal content that were strongly correlated with surface soil levels, with Zn, Pb, and Cu exhibiting the highest concentrations. Elemental correlations, such as Cu-Pb and Zn-Cd synergies and Cd-Ni antagonism, suggest common waste sources and temperature-dependent volatilization during incineration. The washing process (solid–liquid ratio = 1:10) achieved 97.1 ± 2.0% Cl removal, reducing residual Cl to 0.45 ± 0.32%, but demonstrated limited heavy metal elimination (10.28–19.38% efficiency), resulting in elevated concentrations (32.5–60.8% increase) due to 43.4 ± 9.2% mass loss. Notably, the washing effluents exceeded municipal wastewater discharge limits by up to 52-fold for Pb and 38-fold for Cd, underscoring the need for advanced effluent treatment. To mitigate environmental risks, the addition of washed MSWI-FA in cement kilns should be restricted to ≤0.5%, with Cd content prioritized in pre-disposal assessments. This study provides actionable insights for optimizing MSWI-FA co-processing while ensuring compliance with ecological safety standards. Full article

The use of pharmaceuticals and personal care products (PPCPs) is steadily growing as the world’s population both increases and ages. Many of these products are released into the environment via municipal wastewater treatment plants and onsite wastewater treatment systems (septic tanks). Consequently, it is essential to ascertain whether these contaminants pose any risk to aquatic organisms who live in the water bodies receiving this waste. Risk quotients (RQ) are a commonly used method to do so. For our pilot study, we undertook such analysis for three trophic levels: algae, crustaceans, and fish from two small lakes, one fed by septic tanks and the other not. This research was conducted in 2021 from the end of the dry season and through most of the wet season in west central Florida, USA. Of the 14 PPCPs measured, six had RQs that posed a risk to all three trophic levels. This risk increased during the wet season. Both lakes, regardless of whether they directly received PPCPs from septic tanks or not, had some level of risk. However, the lake without septic tanks had a smaller risk, both in elevated RQs and the occurrence to the various species. Of the PPCPs measured, DEET, caffeine, and theophylline posed the greatest risk. Full article

Implementing efficient strategies for the circular recovery and reuse of nutrients from wastewaters is mandatory to meet the Green Deal objectives and Sustainable Development Goals. In this context we investigated the use of zeolitic tuff (containing chabazite and phillipsite) in the selective recovery and reuse of N from various anaerobic liquid digestates in view of their implementation in farm-scale treatment plants. We tested the method on three livestock digestates and two municipal organic solid waste digestates. Adsorption isotherms and kinetics were assessed on each digestate, and a large set of parameters, including (i) contact time, (ii) initial NH₄⁺ concentration, (iii) presence of competing ions, (iv) total solids content, and (vi) separation methods (microfiltration and clarification), were considered in the experimental design. Our results showed that the adsorption mechanism can be explained by the Freundlich model (R² up to 0.97), indicating a multilayer and heterogeneous adsorption, while the kinetic of adsorption can be explained by the pseudo-second-order model, indicating chemical adsorption and ion exchange. The efficiency in the removal of NH₄⁺ was indirectly related to the K⁺ and total solids content of the digestate. Maximum NH₄⁺ removal exceeded 90% in MSW-derived digestates and 80% within 60 min in livestock-derived digestates at a 5% solid/liquid ratio. Thermodynamic parameters confirmed favorable and spontaneous adsorption (ΔG up to −7 kJ⋅mol⁻¹). Farm-scale projections estimate a nitrogen recovery potential of 1.2 to 16 kg N⋅day⁻¹, depending on digestate type and process conditions. These findings support the application of natural zeolitic tuffs as a low-cost, chemical-free solution for ammonium recovery, contributing to sustainable agriculture and circular economy objectives. Full article

The treatment of wastewater and the utilization of the by-products of these processes are an important part of the circular economy. The sewage sludge, a result of wastewater treatment, could be used as a material for plant nutrient supply and/or soil-improving products. The city of Nyíregyháza, Hungary, with 120,000 citizens, has a well-planned water treatment plant operated by Nyírségvíz Ltd., which, in cooperation with the Research Institute of Nyíregyháza, developed a municipal sewage sludge compost (SSC). The closed loop of sewage water treatment and the agricultural utilization of its by-product has been developed and managed. The compost product called Nyírkomposzt was planned for acidic sandy soils. Beyond the agronomic benefits, the sustainable and environmentally sound utilization of SSC reduces sewage sludge disposal. This active involvement of a water utility company demonstrates the potential of cross-sectoral cooperation in solving environmental problems. The quality of the compost fits the Hungarian legislation. To study the effects of 0, 9, 18, and 27 t ha⁻¹ doses of compost on acidic sandy soil, a long-term small plot experiment was started in 2003. The cumulative effects of the regular (every third year, last treatment before sampling in 2021) application of the SSC showed positive changes in basic soil properties, depending on the doses used. Increasing values were found in the case of pH from 4.5 to 6, plant available P₂O₅ from 240 to 690 ppm, and plant available K₂O from 180 to 200 ppm. The plant-available zinc and copper content also increased. Soil organic matter and total N content stabilized at around 0.9% and 0.08%, respectively. The grain yields of winter rye also increased in both investigated years. The yields of 18 t ha⁻¹ treatment were about two times higher compared to the control, but only in 2022 was the difference significant. Our findings underscore the potential of well-planned SSC applications to improve the fertility of ploughed, acidic sandy soil, taking into account the theory of the circular economy by utilizing wastes and decreasing landfilling. Full article

Substantial boosts in the low-energy nano-oxygenation of incoming process water were achieved at a municipal wastewater treatment plant (WWTP) upstream of activated sludge (AS) aeration lanes on a single-pass basis by means of an electric field nanobubble (NB) generation method (with unit residence times of the order of just 10–15 s). Both ambient air and O₂ cylinders were used as gas sources. In both cases, it was found that the levels of dissolved oxygen (DO) were maintained far higher for much longer than those of conventionally aerated water in the AS lane—and at DO levels in the optimal operational WWTP oxygenation zone of about 2.5–3.5 mg/L. In the AS lanes themselves, there were also excellent conversions to nitrate from nitrite, owing to reactive oxygen species (ROS) and some improvements in BOD and E. coli profiles. Nanobubble-enhanced Dissolved Air Flotation (DAF) was found to be enhanced at shorter times for batch processes: settlement dynamics were slowed slightly initially upon contact with virgin NBs, although the overall time was not particularly affected, owing to faster settlement once the recruitment of micro-particulates took place around the NBs—actually making density-filtering ultimately more facile. The development of machine learning (ML) models predictive of NB populations was carried out in laboratory work with deionised water, in addition to WWTP influent water for a second class of field-oriented ML models based on a more narrow set of more easily and quickly measured data variables in the field, and correlations were found for a more facile prediction of important parameters, such as the NB generation rate and the particular dependent variable that is required to be correlated with the efficient and effective functioning of the nanobubble generator (NBG) for the task at hand—e.g., boosting dissolved oxygen (DO) or shifting Oxidative Reductive Potential (ORP). Full article

The integration of renewable energy with circular economy strategies offers effective pathways to reduce greenhouse gas emissions while enhancing local energy independence. This study analyses three real-world projects implemented in Spain that exemplify this synergy. LIFE Smart Agromobility converts pig manure into biomethane to power farm vehicles, using anaerobic digestion and microalgae-based upgrading systems. Smart Met Value refines biogas from a wastewater treatment plant in Guadalajara to produce high-purity biomethane for the municipal fleet, demonstrating the viability of energy recovery from sewage sludge. The UNDERGY project addresses green hydrogen storage by repurposing a depleted natural gas reservoir, showing geochemical and geomechanical feasibility for seasonal underground hydrogen storage. Each project utilises regionally available resources to produce clean fuels—biomethane or hydrogen—while mitigating methane and CO₂ emissions. Results show significant energy recovery potential: biomethane production can replace a substantial portion of fossil fuel use in rural and urban settings, while hydrogen storage provides a scalable solution for surplus renewable energy. These applied cases demonstrate not only the technical feasibility but also the socio-economic benefits of integrating waste valorisation and energy transition technologies. Together, they represent replicable models for sustainable development and energy resilience across Europe and beyond. Full article