Search Results (95)

Grain moisture content is a key variable for safe storage, drying control, and quality management. Microwave sensing is attractive because water strongly modulates the complex relative permittivity (ε* = ε′ – jε″) of granular agricultural products, thereby shaping broadband scattering-parameter spectra. This study presents a meter-referenced feasibility evaluation of an interpretable S-parameter–permittivity–moisture chain using a vector network analyzer over 2–18 GHz. Wheat, maize, and mung bean were prepared at six moisture levels, and the moisture values were referenced to two commercial grain moisture meters (MC_ref) to represent rapid on-site benchmarking rather than absolute gravimetric moisture determination. Therefore, the reported errors should be interpreted as commercial-meter-referenced calibration indicators rather than absolute gravimetric moisture prediction accuracy. Two free-space configurations were compared on the same platform: a two-horn transmission setup under controlled packing and a metal-backed double-pass reflection setup intended to represent single-sided access under loose bulk packing. After SOLT calibration and empty-holder background normalization, ε′ and ε″ were retrieved via complex-domain nonlinear least-squares fitting of physics-based slab models to measured S21 spectra. The results show that moisture-dependent dielectric responses were grain- and configuration-dependent. In particular, ε″ generally provided a more robust moisture-sensitive feature in the free-space transmission configuration, whereas the optimal single-parameter predictor in the metal-backed configuration differed among grains. A mid-band frequency window of approximately 8–16 GHz provided more stable inversion by avoiding low-frequency coupling artefacts and high-frequency signal-to-noise degradation. The metal-backed configuration preserved moisture trends but yielded lower effective ε′ values, likely due to increased air fraction under loose packing. These results indicate that packing state, grain type, and frequency-window selection are critical factors for transferring microwave moisture calibration from laboratory measurements to practical grain-handling scenarios. Full article

Carbon/inorganic hybrid composites have evolved from filler-reinforced materials into design platforms for coupled electromagnetic, thermal, sensing, environmental, protective and energy-related functions. Their distinctive value lies in the possibility of combining a conductive, polarizable or porous carbon phase with an inorganic phase that contributes dielectric, magnetic, catalytic, ionic, thermally conductive or barrier behavior. This review examines carbon/inorganic hybrid multifunctional composites from the viewpoint of structure–property relationships, with emphasis on interfacial design, percolation, anisotropy, hierarchical architecture, processing and metrology. Selected graphitic composite studies are discussed as case studies for broadband dielectric spectroscopy, microwave shielding, high-frequency contact metrology, thermal diffusivity analysis and impedance-monitored graphene filters; these case studies are integrated with the broader international literature on CNT and graphene polymer composites, MXene films and foams, graphene/metal oxide photocatalysts, boron nitride/carbon thermal networks, biochar–graphene adsorbents, smart coatings, sensors, supercapacitors and water remediation systems. The central argument is that credible multifunctionality requires more than measuring several properties on the same material. It requires simultaneous or service-relevant co-optimization under constraints of thickness, density, processability, aging, humidity, corrosive media, regeneration, toxicity, economic feasibility and scalable fabrication. The review concludes with design rules and reporting recommendations intended to help move the field from impressive property demonstrations toward application-ready hybrid material systems. Full article

The development of cost-effective and resource-rich materials is crucial for the practical application of microwave absorbers. This study demonstrates the successful fabrication of core-shell Fe and TiC nanoparticles encapsulated within carbon shells using the arc discharge method. The samples are designated as Fe3Ti1 and Fe1Ti3, where the numbers indicate the Fe-to-Ti mass ratio in the precursor (e.g., Fe1Ti3 = 1:3 by mass). In the arc discharge synthesis mechanism, the mass ratio of Fe to Ti in the raw material was adjusted from 3:1 to 1:3 to optimize the Fe/TiC/C interfaces under a CH₄ forming gas atmosphere. TEM analysis reveals spherical and polyhedral nanoparticles with diameters of 30–50 nm and a uniform carbon shell thickness of 3–4 nm. Raman spectroscopy shows that the Fe1Ti3 sample has a higher defect density (I_D/I_G = 1.13) compared to Fe3Ti1 (0.87), indicating a more disordered carbon structure. Magnetic measurements yield saturation magnetization values of 87 emu/g for Fe3Ti1 and 50 emu/g for Fe1Ti3, with coercivities of 190.72 Oe and 203.65 Oe, respectively. When composited with paraffin at 50 wt% loading, the Fe1Ti3 sample exhibits superior microwave absorption performance, achieving a minimum reflection loss (RL) of −25.22 dB at 8.23 GHz and an effective absorption bandwidth (RL ≤ −10 dB) of 4 GHz (6.5–10.5 GHz) at a thickness of 2.5 mm. This enhanced performance is attributed to the synergistic effect of multiple loss mechanisms, including conduction loss within the three-dimensional core-shell architecture, interfacial polarization at the heterojunctions between the core and the carbon shell, and magnetic loss induced by ferromagnetic behavior associated with defects in both the shell and carbon atomic layers. The magnetic loss in the (Fe/TiC)@C nanocomposites primarily arises from the natural resonance (at ~6.5 GHz) and exchange resonance (at ~12 GHz) of the Fe cores. The dielectric loss is primarily attributed to dipole, interfacial, and space charge polarization from TiC and the carbon shell, as well as multiple scattering effects between nanoparticles. Furthermore, far-field radar cross-section simulations substantiate that the Fe/TiC@C nanocomposite demonstrates excellent radar wave attenuation capability. Further, first principles simulations reveal that introducing Fe at the C/TiC interface induces strong charge redistribution and orbital hybridization, transforming a localized dielectric interface into a highly conductive and electronically coupled C/Fe/TiC system. This interfacial modulation enhances both dielectric loss (via charge transport and polarization) and magnetic loss (via Fe-induced magnetic interactions), thereby enabling optimized dielectric-magnetic synergy for broadband microwave absorption in (Fe/TiC)@C nanocomposites. Full article

This study investigates the dielectric behavior and NO_x storage properties of Pt/Ba–Al₂O₃ NO_x storage materials using microwave cavity perturbation, operando DRIFTS, and impedance spectroscopy with respect to their applicability in a radio-frequency-based NO_x dosimeter-type sensor. Dielectric losses (ε″) are identified as the most sensitive indicator of NO_x storage, exhibiting a clear linear correlation with both the accumulated NO_x dose and the utilization of Ba storage sites. Approximately 35% of the available Ba sites participate in nitrite and nitrate formation, and the absolute dielectric loss response increases proportionally with the Ba content of the NOx storage catalyst. In contrast, the permittivity (ε′) shows only minor changes, which are mainly influenced by temperature. Temperature-dependent experiments reveal stable NO_x storage with negligible desorption up to 350 °C, whereas pronounced desorption processes at 400 °C significantly limit the linear dosimeter behavior. Operando DRIFTS measurements on Pt/Ba–Al₂O₃ functional films confirm temperature-dependent formation of nitrites and nitrates, with nitrates dominating the NO_x storage at elevated temperatures. Capacitance measurements show a slight increase during NO_x storage, indicating a moderate increase in permittivity. Overall, Pt/Ba–Al₂O₃ NO_x storage materials exhibit a robust, quantitatively interpretable dielectric response that is well suited for radio-frequency-based, dosimeter-type NO_x sensing. Full article

In the current study, the dielectric behavior of ternary mixtures composed of glycerol and water with various salt additives is investigated over a frequency range that extends from 0.5 to 20 GHz and at temperatures between 5 and 55 °C. The investigated mixtures consisted of glycerol and water with glycerol volume ratios of 20%, 40%, and 60%. To explore the salt addition’s effect on the dielectric properties, different moderate ionic strengths of glycerol–water mixtures were prepared with NaCl concentrations of 0.10, 0.20, and 0.30 M for the same glycerol volume ratios. The ion-specific effects on the dielectric properties were investigated for prepared mixtures with a 0.10 M concentration of Na₂SO₃, NaNO₃, and KCl for the 20% glycerol ratio to explore ions with different charge density and hydration tendencies. Using dielectric spectroscopy, the frequency dependence of the real (${\epsilon }^{\prime }$) and imaginary (${\epsilon }^{″}$) dielectric constants was measured, and the associated dielectric parameters were extracted using the Cole–Cole model. This study shows that increasing the salt concentration results in a slight decrease in ${\epsilon }^{\prime }$ while ${\epsilon }^{″}$ increases dramatically, especially at lower frequencies, due to enhanced DC conductivity. An isopermittivity behavior is observed in ${\epsilon }^{\prime }$ as the temperature changes across all mixtures, and it is found to be insensitive to the addition of salt, indicating that it is mainly dictated by the glycerol–water dipolar relaxation network. Among the tested mixtures is the 20% glycerol mixture with 0.10 M KCl, which exhibits the highest ${\epsilon }^{″}$ value in the low-frequency range, attributed to its relatively high DC conductivity. Additionally, the dielectric properties of mixtures with higher glycerol ratios are found to be less sensitive to the addition of salt due to their high viscosity and the higher structured solvent network, which collectively limit ionic mobility and suppress changes in dielectric response. Full article

As a ferrite material with excellent magnetic and dielectric properties, CoFe₂O₄ is in high demand for applications in areas such as wave absorption and magnetic storage. Effective regulation of its nanoscale morphology is central to improving application performance. Conventional synthesis methods often face challenges including poor particle dispersion and irregular morphology, which limit further optimization of material properties. In this study, a combined approach of microwave hydrothermal synthesis and annealing was employed to systematically investigate the effects of hydrothermal temperature, reaction time, and annealing parameters on the morphology and properties of CoFe₂O₄. The samples were characterized using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, and other techniques. Experimental results show that process parameters exert a notable influence on the crystallinity, particle dispersibility, magnetic and wave-absorbing properties of CoFe₂O₄: the sample prepared by microwave hydrothermal treatment at 75 °C for 30 min exhibits relatively better wave-absorbing performance, with a minimum reflection loss of less than −30 dB and an effective absorption bandwidth covering 8~16 GHz; the sample treated at 100 °C for 15 min shows a more balanced magnetic performance, with the saturation magnetization approaching 60 emu/g. The quantitative structure–property relationships of pure-phase CoFe₂O₄ across microwave hydrothermal and post-annealing processes, and achieve stable, reproducible performance enhancements under optimized mild conditions. These results supplement key experimental data for the low-temperature preparation of CoFe₂O₄ and establish a practical, energy-efficient parameter framework for future structural design and process optimization of this important magnetic material. Full article

The food processing industry is seeking new technologies to enhance product safety, extend shelf life, and optimise food quality in response to growing consumer demand for high-quality products. Since the discovery of plasma technology, its potential applications in food processing have been numerous. For most of these applications, plasma characterisation is key to successfully scaling up from laboratory to industrial settings. A highly valuable tool for plasma characterisation is optical emission spectroscopy (OES), which serves as a non-invasive diagnostic method to monitor reactive species, specifically excited atoms and molecules (reactive oxygen and nitrogen species—RONS) that are critical for food treatment. The main role of OES in food control is to enable species identification and real-time process monitoring, providing feedback on electron temperature and density to prevent thermal damage to sensitive food products. It also facilitates optimisation by adjusting voltage and gas flow rates to maximise the production of antimicrobial species. These results ensure that processes are reliable and repeatable, supporting the transition from laboratory-scale to industrial applications. The paper provides an overview of the use of optical emission spectroscopy in various applications of plasma technology in food processing, including the determination of the elemental composition of raw materials and final products, detection of contaminants, quality control, determination of characteristic plasma parameters, and ensuring compliance with food safety regulations. Full article

A water-rich muscle-equivalent tissue-mimicking phantom within a polymeric matrix was experimentally evaluated through a multimodal characterization methodology to determine whether it reproduces the coupled dielectric–thermal behavior of hydrated biological tissue under exposure to electromagnetic waves. The material was analyzed using thermogravimetric analysis, microwave dielectric spectroscopy from 1.5 to 4.0 GHz, VIS–NIR spectroscopy between 350 and 1200 nm, and terahertz time-domain reflection. The thermogravimetric results confirmed dominant water content, with primary mass loss below 200 °C, establishing hydration as the governing factor of its thermal response. Next, the microwave dielectric measurements show that the phantom exhibits a relative permittivity of 37.4 and an electrical conductivity of 2.4 S/m. On the other hand, the VIS–NIR spectra show smooth broadband absorption with limited spatial variability, and principal component analysis reveals macroscopic optical homogeneity without structural spectral distortion. In the THz regime, strong broadband attenuation characteristic of water-rich matrices is observed, and reflection-mode measurements enable robust assessment of temporal stability through time- and frequency-domain signatures. Finally, a microwave thermal validation demonstrates stable behavior under low-power excitation, whereas under hyperthermia-level irradiation, a significant thermal drift of −3.985 °C/h was reached under non-adiabatic conditions, identifying hydration-mediated moisture redistribution as the principal limitation during prolonged high-power exposure. Collectively, these results demonstrate cross-regime dielectric–thermal consistency while explicitly defining the hydration-driven constraints governing long-term stability, providing a validated reference material for broadband electromagnetic and thermal biomedical experimentation. Full article

This review article provides a systematic analysis of synthesis methods, structural characteristics, and functional properties of spinel-structured ferrite nanoparticles (MFe₂O₄). The physicochemical principles, advantages, and limitations of various synthesis techniques—including co-precipitation, combustion, sol–gel, thermal decomposition, hydrothermal, solvothermal, microwave-assisted, sonochemical, electrochemical, and solid-state reaction methods—are comparatively discussed. The influence of synthesis parameters on crystal structure, morphology, and cation distribution between tetrahedral and octahedral sites, as well as on magnetic, dielectric, and optical properties, is critically analyzed. Furthermore, the capabilities of characterization techniques such as X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive spectroscopy (SEM/EDS), Fourier-transform infrared spectroscopy (FTIR), FT-Raman spectroscopy, dielectric measurements, and magnetic measurements for investigating spinel ferrites are comprehensively summarized. Finally, the high potential of spinel ferrite nanoparticles for applications in electronics, microwave devices, water treatment, catalysis, sensors, and biomedical fields is highlighted. Full article

Many industrial sectors are concerned about microbiological contamination and the associated risk of microbiologically influenced corrosion (MIC). This applies in particular to the transmission and storage of fuels in the refining industry. Exceeding a certain level of these contaminants poses a serious risk to fuel quality and can cause storage and pipeline infrastructure corrosion. This situation requires an urgent evaluation of microorganism levels in the fuel to avert such detrimental consequences. Diesel fuels containing biofuel additives are particularly susceptible to these phenomena. Traditional detection methods are limited by low sensitivity, high costs, and long turnaround times, making them unsuitable for quick, on-site, and real-time detection and monitoring. A novel approach involves the application of microwave dielectric testing to quantify microbial load in diesel fuel. Microwave dielectric spectroscopy offers a non-destructive, label-free solution, providing rapid information on microorganism presence. Combined with chemometric techniques, it effectively estimates total microorganism counts in diesel fuel. Measurement in the X-band range (8.2–12.4 GHz) takes a few seconds. Calibration with known bacterial and fungal concentrations (10³ to 10⁷ CFU/mL) and principal component analysis (PCA) of the spectroscopic data allow for clear differentiation of contamination levels, categorizing them from acceptable to hazardous. The sensitivity limit of the proposed method corresponds to a bacterial concentration of 10³ CFU/mL. Full article

Transition metal (TM)-doped zinc oxide (ZnO) and zirconium dioxide (ZrO₂) nanocrystals exhibit complex correlations between crystal structure, defect chemistry, vibrational properties, and magnetic behavior that are strongly governed by synthesis route and dopant incorporation mechanisms. This review critically summarizes recent progress on Fe-, Mn-, and Co-doped ZnO and ZrO₂ nanocrystals synthesized by wet chemical, hydrothermal, and microwave-assisted hydrothermal methods, with emphasis on synthesis-driven phase evolution and apparent solubility limits. ZnO and ZrO₂ are treated as complementary host lattices: ZnO is a semiconducting, piezoelectric oxide with narrow solubility limits for most 3d dopants, while ZrO₂ is a dielectric, polymorphic oxide in which transition metal doping may stabilize tetragonal or cubic phases. Structural and microstructural studies using X-ray diffraction, electron microscopy, Raman spectroscopy, and Mössbauer spectroscopy demonstrate that at low dopant concentrations, TM ions may be partially incorporated into the host lattice, giving rise to diluted or defect-mediated magnetic behavior. When solubility limits are exceeded, nanoscopic secondary oxide phases emerge, leading to superparamagnetic, ferrimagnetic, or spin-glass-like responses. Magnetic measurements, including DC magnetization and AC susceptibility, reveal a continuous evolution from paramagnetism in lightly doped samples to dynamic magnetic states characteristic of nanoscale magnetic entities. Vibrational spectroscopy highlights phonon confinement, surface optical phonons, and disorder-activated modes that sensitively reflect nanocrystal size, lattice strain, and defect populations, and often correlate with magnetic dynamics. Rather than classifying these materials as diluted magnetic semiconductors, this review adopts a synthesis-driven and correlation-based framework that links dopant incorporation, local structural disorder, vibrational fingerprints, and magnetic response. By emphasizing multi-technique characterization strategies required to distinguish intrinsic from extrinsic magnetic contributions, this review provides practical guidelines for interpreting magnetism in TM-doped oxide nanocrystals and outlines implications for applications in photocatalysis, sensing, biomedicine, and electromagnetic interference (EMI) shielding. Full article

High-performance dielectric materials that can be processed at ultra-low temperatures are essential for next-generation LTCC technologies and compact RF–microwave components. In this work, a multicomponent Bi–Fe–Nb oxide system was synthesized using a modified citrate sol–gel method and thermally treated at only 400 °C to investigate its structural evolution and dielectric behavior. XRD and Raman analysis revealed the coexistence of a well-crystallized BiOCl phase embedded within a partially amorphous Bi–Fe–Nb–O matrix. SEM and EDS mapping confirmed the presence of two distinct microstructural regions, reflecting differences in local composition and crystallization kinetics. Microwave measurements at 2.7 and 5.0 GHz showed low dielectric losses and a stable dielectric response. Impedance spectroscopy in the RF range revealed strong Maxwell–Wagner polarization at low frequencies and thermally activated relaxation evidenced by the temperature shift in the modulus and impedance peaks. Arrhenius analysis of the relaxation frequencies yielded similar activation energies from both modulus and impedance formalisms, indicating a single underlying relaxation mechanism. Equivalent-circuit fitting confirmed non-Debye behavior, with nearly temperature-independent capacitance and decreasing resistance consistent with thermally activated conduction. These results demonstrate that the Bi–Fe–Nb system exhibits promising dielectric stability and functional behavior even when processed at exceptionally low temperatures. Full article

Breast tissue-mimicking phantoms are essential tools for validating microwave imaging systems designed for early breast cancer detection. In this work, we report the fabrication and comprehensive characterization of oil-in-gelatin phantoms emulating normal, benign, and malignant breast tissues. The phantoms were manufactured with controlled mixtures of kerosene, safflower oil, and gelatin, and their dielectric properties were experimentally evaluated using a free-space transmission method with a Vector Network Analyzer across the 100 MHz–10 GHz range. Results demonstrated significant contrast in permittivity and conductivity among the different tissue types, consistent with values reported in the literature. Long-term stability was confirmed for up to six months under controlled storage. Additional structural and thermal characterization was performed using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA), providing insight into molecular composition and thermal response. The proposed method enables reproducible, low-cost, and stable phantom fabrication, offering reliable tissue models to support experimental validation and optimization of microwave-based breast cancer detection systems. Full article

Agricultural nondestructive testing technology is pivotal in safeguarding food quality assurance, safety monitoring, and supply chain transparency. While conventional optical methods such as near-infrared spectroscopy and hyperspectral imaging demonstrate proficiency in surface composition analysis, their constrained penetration depth and environmental sensitivity limit effectiveness in dynamic agricultural inspections. This review highlights the transformative potential of microwave technologies, systematically examining their operational principles, current implementations, and developmental trajectories for agricultural quality control. Microwave technology leverages dielectric response mechanisms to overcome traditional limitations, such as low-frequency penetration for grain silo moisture testing and high-frequency multi-parameter analysis, enabling simultaneous detection of moisture gradients, density variations, and foreign contaminants. Established applications span moisture quantification in cereal grains, oilseed crops, and plant tissues, while emerging implementations address storage condition monitoring, mycotoxin detection, and adulteration screening. The high-frequency branch of the microwave–millimeter wave systems enhances analytical precision through molecular resonance effects and sub-millimeter spatial resolution, achieving trace-level contaminant identification. Current challenges focus on three areas: excessive absorption of low-frequency microwaves by high-moisture agricultural products, significant path loss of microwave high-frequency signals in complex environments, and the lack of a standardized dielectric database. In the future, it is essential to develop low-cost, highly sensitive, and portable systems based on solid-state microelectronics and metamaterials, and to utilize IoT and 6G communications to enable dynamic monitoring. This review not only consolidates the state-of-the-art but also identifies future innovation pathways, providing a roadmap for scalable deployment of next-generation agricultural NDT systems. Full article

Relaxation behavior of water confined in reverse micelles under temperature-induced micelle clustering is undertaken using broadband dielectric spectroscopy in frequency range 1 Hz–20 GHz. All microemulsion systems with sufficiently noticeable micelle water pool (water/surfactant molar ratio W > 10) depict three relaxation processes, in low, high and microwave frequencies, anchoring with relaxation of shell (bound) water, orientation of surfactant anions at water-surfactant interface and relaxation of bulk water confined in reverse micelles. The analysis of dielectric relaxation processes in AOT-based w/o microemulsions under temperature induced clustering of reverse micelles were made according to structural information obtained in NMR and conductometry experiments. The “wait and switch” relaxation mechanism was applied for the explanation of results for water in the bound and bulk states under spatial limitation in reverse micelles. It was shown that surfactant layer predominantly influences the bound water. The properties of water close to AOT interface are determined by strong interactions between water and ionic AOT molecules, which perturb water H-bonding network. The decrease in micelle size causes a weakening of hydrogen bonds, deformation of its steric network and reduction in co-operative relaxation effects. Full article