Search Results (147)

In this work, the W element, with a larger atomic radius compared to Co, Fe, and Ni, was added to modify the microstructure and enhance the yield strength of CoFeNi medium entropy alloy (MEA). A detailed study was conducted to clarify the effects of W additions and annealing temperatures on the microstructure evolution and mechanical properties of CoFeNiW_x (x = 0, 0.1, and 0.3) MEAs. CoFeNiW_0.1 retained a single FCC structure without the formation of precipitates in the FCC phase, indicating that W, with a larger atomic radius, can completely dissolve in CoFeNiW_0.1. For CoFeNiW_0.3 MEA, coarse particles with an average diameter of ~2 μm appeared after homogenizing. Nevertheless, when the alloy was annealed at 800 °C and 900 °C, fine particles formed, with the average diameters of approximately 144 nm and 225 nm, respectively. After annealing at 800 °C, the CoFeNiW_0.3 with a partially recrystallized microstructure exhibited better comprehensive mechanical properties. Full article

In order to improve the microstructure and corrosion resistance of entropy alloy in the FeCrNi system, laser melting deposition technology was used as a preparation method to study the effects of different contents of Al and Ti on the microstructure and corrosion resistance of entropy alloy in FeCrNi(AlTi)_x (x = 0.17, 0.2, and 0.24). The results show that the addition of Al and Ti elements can change the phase structure of the alloy from a single FCC phase structure to an FCC + BCC biphase structure. The BCC phase volume fraction of FeCrNi(AlTi)_0.2 is the highest among the three alloys, reaching 37.5%. With the addition of Al and Ti content, the grain of the alloy will be refined to a certain extent. In addition, the dual-phase structure will also improve the corrosion resistance of the alloy. In 3.5 wt.% NaCl solution, the increase of Al and Ti content can effectively improve the protection of the passivation film on the surface of the entropy alloy in FeCrNi(AlTi)_x, effectively inhibit the large-scale corrosion phenomenon on the alloy surface, and thus improve the corrosion resistance of the alloy. In a certain range, increasing the content of Al and Ti elements in the FeCrNi(AlTi)_x system can improve the corrosion resistance of the alloy. Full article

Medium-entropy alloys (MEAs) have attracted significant attention due to their unique structure–property relationships. In this study, we examine the effects of lattice distortion on the mechanical properties of Nb-Ti-V-Zr MEAs, focusing on two alloy series: Nb(Ti_1.5V)_xZr and Nb(TiV)_xZr (x = 1, 2, 3, 4 and 5). Experimental results show that the Nb(TiV)_xZr r alloys exhibit greater atomic size mismatches and increased lattice distortion compared to the Nb(Ti_1.5V)_xZr alloys, leading to higher yield strengths via enhanced solid-solution strengthening. However, excessive lattice distortion does not ensure an optimal strength–ductility balance, as the alloys with the highest distortion demonstrate limited plasticity. Thus, moderate reduction in lattice distortion proves beneficial in achieving an excellent compromise between strength and ductility. These findings offer valuable guidance for leveraging lattice distortion in the design of high-strength, high-ductility, body-centered cubic (BCC) MEAs for extreme environments. Full article

Based on the innovative mode driven by “data + artificial intelligence”, in this study, three methods, namely Gaussian noise (GAUSS Noise), the Generative Adversarial Network (GAN), and the optimized Generative Adversarial Network (GANPro), are adopted to expand and enhance the collected dataset of element contents and the hardness of the AlCoCrCuFeNi high-entropy alloy. Bayesian optimization with grid search is used to determine the optimal combination of hyperparameters, and two interpretability methods, SHAP and permutation importance, are employed to further explore the relationship between the element features of high-entropy alloys and hardness. The results show that the optimal data augmentation method is Gaussian noise enhancement; its accuracy reaches 97.4% under the addition of medium noise (σ = 0.003), and an optimal performance prediction model based on the existing dataset is finally constructed. Through the interpretability method, it is found that the contributions of Al and Ni are the most prominent. When the Al content exceeds 0.18 mol, it has a positive promoting effect on hardness, while Ni and Cu exhibit a critical effect of promotion–inhibition near 0.175 mol and 0.14 mol, respectively, revealing the nonlinear regulation law of element contents. This study solves the problem of revealing the mutual relationship between the element contents and hardness of high-entropy alloys in the case of a lack of alloy data and provides theoretical guidance for further improving the performance of high-entropy alloys. Full article

It is essential to develop the optimal hot-working process of the (CoCrNi)₉₄Al₃Ti₃ alloy, a recently developed precipitation-hardened medium-entropy alloy with promising mechanical properties, for its industrial application. In this study, the hot workability of the as-forged (CoCrNi)₉₄Al₃Ti₃ alloy was investigated over a temperature range of 1000 °C to 1150 °C and a strain rate ranging from 0.001 to 1 s⁻¹ using a Gleeble-1500D thermal simulation machine of Dynamic Systems Inc., USA. As a result, the constitutive relationship was established, and the hot deformation activation energy was calculated as 433.2 kJ/mol, suggesting its well-defined plastic flow behavior under low-energy-input conditions. Hot-processing maps were constructed to identify the stable hot-working regions. Microstructure analysis revealed that the hot-forged (CoCrNi)₉₄Al₃Ti₃ alloy exhibited continuous dynamic recrystallization (CDRX) behavior under optimal hot-working conditions. Considering the hot-processing maps and DRX characteristics, the optimal hot-working window of hot-forged (CoCrNi)₉₄Al₃Ti₃ alloy was identified as 1100 °C with a strain rate of 0.1 s⁻¹. This work offers valuable guidance for developing high-efficiency forming processes for (CoCrNi)₉₄Al₃Ti₃ medium-entropy alloy. Full article

This study investigates the tribocorrosion behavior of 304 stainless steel (304SS), S31254 super austenitic stainless steel (S31254 SASS), and a medium-entropy austenitic stainless steel (MEASS) in 3.5 wt.% NaCl solution under sliding conditions. The objective is to clarify the performance differences among these alloys when exposed to simultaneous mechanical wear and corrosion. Electrochemical techniques, including potentiodynamic polarization and potentiostatic sliding tests, were used to evaluate corrosion resistance and repassivation behavior. Quantitative analysis based on ASTM G119 revealed that MEASS showed a 68% lower total material loss compared to 304SS and a 55% lower loss compared to S31254. MEASS also exhibited the lowest corrosion current density (1.46 μA/cm²) under tribocorrosion conditions, representing an 83% reduction compared to 304SS. These improvements are attributed to the higher chromium and nickel contents of MEASS, which enhance passive film stability and reduce susceptibility to localized corrosion. The results demonstrate that MEASS offers superior resistance to combined mechanical and corrosive degradation in chloride-containing environments. Full article

In this study, 20 wt.% of Nb was incorporated into a CrFeNi medium-entropy alloy (MEA) powder system to prepare CrFeNi-Nb composite coatings on a Q235B mild steel substrate by laser cladding technology. The effects of Nb addition on the phase composition, microstructure, and wear resistance of CrFeNi coatings were systematically investigated. Microstructural characterization revealed that the CrFeNi coating exhibited a single face-centered cubic (FCC) phase structure, while the CrFeNi-Nb composite coating demonstrated a dual-phase structure comprising FCC phase and Laves phase. The Laves phase significantly enhanced the microhardness and wear resistance of the coating. The average microhardness of the CrFeNi-Nb coating increased by 259.62% compared to the substrate and 190.58% compared to the Nb-free CrFeNi coating. The average coefficient of friction (COF) of the coating decreased from 0.74 to 0.68; the wear rate reduced from 5.77 × 10⁻⁴ mm³ N⁻¹ m⁻¹ to 2.26 × 10⁻⁴ mm³ N⁻¹ m⁻¹; and the weight loss decreased from 10.77 mg to 4.3 mg. The experimental results demonstrated that the addition of Nb promoted the formation of the Laves phase in the CrFeNi MEA, which effectively improved the wear resistance of the coating. Full article

This study investigates the interfacial reactions of FeCoNiCr and FeCoNiMn medium-entropy alloys (MEAs) with Sn and Sn-3Ag-0.5Cu (SAC305) solders at 250 °C. The evolution of interfacial microstructures is analyzed over various aging periods. For comparison, the FeCoNiCrMn high-entropy alloy (HEA) is also examined. In the Sn/FeCoNiCr system, a faceted (Fe,Cr,Co)Sn₂ layer initially forms at the interface. Upon aging, the significant spalling of large (Fe,Cr,Co)Sn₂ particulates into the solder matrix occurs. Additionally, an extremely large, plate-like (Co,Ni)Sn₄ phase forms at a later stage. In contrast, the Sn/FeCoNiMn reaction produces a finer-grained (Fe,Co,Mn)Sn₂ phase dispersed in the solder, accompanied by the formation of the large (Co,Ni)Sn₄ phase. This observation suggests that Mn promotes the formation of finer intermetallic compounds (IMCs), while Cr facilitates the spalling of larger IMC particulates. The Sn/FeCoNiCrMn system exhibits stable interfacial behavior, with the (Fe,Cr,Co)Sn₂ layer showing no significant changes over time. The interfacial behavior and microstructure are primarily governed by the dissolution of the constituent elements and composition ratio of the HEAs, as well as their interactions with Sn. Similar trends are observed in the SAC305 solder reactions, where a larger amount of fine (Fe,Co,Cu)Sn₂ particles spall from the interface. This behavior is likely attributed to Cu doping, which enhances nucleation and stabilizes the IMC phases, promoting the formation of finer particles. The wettability of SAC305 solder on MEA/HEA substrates was further evaluated by contact angle measurements. These findings suggest that the presence of Mn in the substrate enhances the wettability of the solder. Full article

Because of their low density and excellent material properties, lightweight Ti-rich medium-entropy alloys (MEAs) have great potential for application in the aerospace and automotive industries. This study investigated the effects of B doping on the microstructure and mechanical properties of a (Ti₆₅(AlCrNbV)₃₅)_100−xB_x alloy series. The mechanical properties of the alloys were then enhanced through thermomechanical treatment, and the strengthening mechanism was explored by characterizing the alloys’ microstructure and mechanical properties. X-ray diffraction revealed that the (Ti₆₅(AlCrNbV)₃₅)_100−xB_x alloys retained their body-centered cubic structure. However, the addition of B resulted in a rightward shift in the diffraction peaks due to B having a smaller atomic radius compared with the other constituent elements. Weak diffraction peaks corresponding to TiB were discovered in the diffraction patterns for the alloys with 0.4 or 0.6% B content (named B0.4 and B0.6, respectively). The hardness of the homogenized alloys was increased from 321 Hv for the base alloy (B0) to 378 Hv for B0.6. In tensile testing, the homogenized alloy with 0.2% B content (B0.2) exhibited a yield strength of 1054 MPa and 21% elongation, which represented 17% greater strength compared with B0. Conversely, the mechanical properties of B0.4 and B0.6 were poorer due to precipitation at grain boundaries. After thermomechanical treatment, the alloys’ strength and hardness increased with increasing B content despite various heat treatment conditions. The recrystallization behavior of the alloys tended to be delayed by B doping, resulting in an increase in the recrystallization temperature. After recrystallization at 900 °C, the elongation of B0, B0.1, and B0.2 exceeded 20%. Of the (Ti₆₅(AlCrNbV)₃₅)_100−xB_x alloys in the series, B0.2 presents the optimal combination of favorable yield strength and ductility (1275 MPa and 10%, respectively). Full article

Aerospace and marine engineering impose higher requirements on mechanical properties and lightweight design of materials. In this work, combining the high mechanical properties of FeCrNi medium entropy alloy (MEA) and the lightweight advantages of lattice structure, four types of high-performance FeCrNi MEA lattice structures (BCC, BCCZ, FCC, and FCCZ) were prepared by selective laser melting (SLM) technology, and their dynamic mechanical properties were systematically characterized via split Hopkinson pressure bar (SHPB) method. The results demonstrate that the FCCZ FeCrNi MEA lattice structure exhibits superior comprehensive performance among the four lattice structures, achieving the highest specific compressive strength of 59.1 MPa·g⁻¹·cm⁻³ and specific energy absorption of 26.3 J/g, significantly outperforming conventional lattice materials including 316L and AlSi10Mg alloys. Furthermore, the finite element simulation and Johnson-Cook (J-C) constitutive model of the dynamic compression process can effectively predict the microstructural evolution and mechanical response of lattice structure, providing critical theoretical guidance for optimizing the design of high-performance lattice structure materials. Full article

Medium-entropy alloys (MEAs) exhibit properties comparable or even superior to high-entropy alloys (HEAs). Due to their very good resistance in thermomechanical conditions and corrosive environments and unique electrical and magnetic properties, medium-entropy alloys are good candidates for coating applications. One of the most economically effective methods of producing metallic coatings is electrodeposition. In this work, the structure of an electrodeposited CoFeNi medium-entropy alloy coating on a copper substrate from a metal chlorides solution (FeCl₂ ∙ 4H₂O + CoCl₂ ∙ 6H₂O + NiCl₂ ∙ 6H₂O) with the addition of boric acid (H₃BO₃) was investigated. The coating was characterized by a nanocrystalline structure identified by transmission electron microscopy examination and X-ray diffraction methods. Based on XRD and TEM, the face-centered cubic (FCC) phase of the CoFeNi MEA coating was identified. The high corrosion resistance of the MEA coating in a 3.5% NaCl environment at 25 °C was confirmed by electrochemical tests. Full article

Medium-entropy alloys (MEAs) allow the formation of different phases, generally in a solid-solution state, and compounds that favor obtaining alloys with properties superior to those of conventional alloys. In this study, medium-entropy CuNiSiCrCoTiNbx alloys were fabricated via melting in a vacuum induction furnace. The influence of the Nb addition (X = 0, 0.5 and 1 wt%) alloying elements on the microstructure, hardness, and wear resistance of the CuNiSiCrCoTiNb₀ (M1), CuNiSiCrCoTiNb_0.5 (M2), and CuNiCoCrSiTiNb₁ (M3) alloys were explored using X-ray diffraction (XRD), scanning electron microscopy (SEM), and a ball-on-disc tribometer, respectively. In general, the results indicated that the incorporation of Nb alloying element promoted the evolution of the microstructure, increased the hardness, and improvement of the wear resistance. The XRD and SEM findings demonstrate that higher Nb addition and aging heat treatment (AT) modification mainly favored the formation of dendritic regions and the precipitation of the Co₂Nb, Cr₃Si, and Ni₂Si phases, which promoted the refinement and strengthening of the microstructure. Significant increases in hardness were recorded: 11.95% increased, promoted by the addition of Nb before (E1) and after (E2, E3, and E4) the heat treatments. The maximum hardness values recorded were 92 ± 0.11 (AC) and 103 ± 0.5 HRB (AT-60 min) for the M3 alloy. The increase in hardness caused by Nb addition and aging heat treatments contributed to the dry sliding wear resistance response, decreasing material loss by 20%. This was related to the high concentration of precipitated phases rich in CoNb, CrSi, and NiSi with high hardness. Finally, the M3 alloy aged for 60 min exhibited the best specific wear rate behavior, with a material loss of 1.29 ${\mathrm{m}\mathrm{m}}^3$. The commercial Cu-Be C17510 alloy experienced a maximum hardness of 83.47 Hardness Rockwell B, HRB, and a high wear rate of 3.34 mm³. Full article

In this study, the effect of high temperature on the mechanical performance of CoCrNi medium-entropy alloy octet-truss lattice material fabricated via laser powder bed fusion (LPBF) is investigated by compressive test and numerical simulation method. The results reveal that the strength and energy absorption performance of CoCrNi octet-truss lattice material with a hollow truss are higher than those of ones with a solid truss; however, they diminish by 30% and 50%, respectively, as temperature rises from 25 °C to 600 °C. As the temperature rises, the potential barrier for dislocation slip decreases, making it easier for dislocations to move at high temperatures and thus reducing the strength. CoCrNi octet-truss lattice materials present the failure mechanism of progressive collapse at varied temperatures. Meanwhile, the mechanical performance of the experimental testing agreed well with numerical simulation results. The numerical results show that the strength and energy absorption properties of the CoCrNi lattice materials increase as the relative density, however, decreases with increasing temperature. Additionally, CoCrNi octet-truss lattice materials maintain exceptional energy absorption performance at varied temperatures. Full article

This study focuses on the cobalt-free medium-to-high-entropy alloys Al_xCrFe₂Ni₂ and Al_xTi_xCrFe₂Ni₂, investigating the influence of Al_x and Ti_x (where x = 0.2, 0.3, 0.4, 0.5, and 0.6) on the development of microstructural and mechanical properties in as-cast and annealed states. Structural changes were examined using optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) measurements, while mechanical properties were evaluated through Vickers hardness testing and compression testing. X-ray diffraction analysis of the Al_xCrFe₂Ni₂ alloys confirmed that increasing the Al content in the as-cast state leads to the formation of a BCC phase, which completely dissolves into the FCC matrix after homogenization annealing. These single-phase alloys exhibit good ductility with relatively high strain hardening, such as the Al_0.6CrFe₂Ni₂ alloy, which achieved a maximum compressive strength of ${\sigma }_{max}=1511 \mathrm{M}\mathrm{P}\mathrm{a}$ at 50% deformation. A significant strengthening effect of Ti was observed in the Al_xTi_xCrFe₂Ni₂ alloys, the mechanical properties of which are closely linked to the higher BCC phase content in the homogenized structure. The highest compressive strength, ${\sigma }_{max}=2239 \mathrm{M}\mathrm{P}\mathrm{a}$, was achieved by the Al_0.5Ti_0.5CrFe₂Ni₂ alloy, which fractured via a transcrystalline brittle fracture at 43% deformation. All alloys investigated offer an excellent balance between strength and ductility, which could meet the requirements of demanding structural applications. Full article

CoCrNi medium-entropy alloy (MEA) coatings prepared using laser cladding (LC) with unique properties have aroused great interest in recent years and have been widely studied. However, limited studies have been conducted on the effect of adding Al/Fe on the wear properties of CoCrNi MEA coatings prepared on the surface of stainless steel. In this study, AlCoCrFeNi, CoCrFeNi, and CoCrNi MEA LC coatings were prepared on a stainless steel substrate. The grain structures and microscopic morphologies of coatings were characterized, and the wear mechanisms were analyzed using the nano-indentation and wear tests. The hardness-strengthening mechanism was theoretically investigated using phase diagrams and molecular dynamics (MD). The phase diagram results show that the addition of Al lowered the nucleation initiation temperature, thereby increasing the nucleation rate and forming more grains. Moreover, according to the Voronoi volumes and mean–square atomic displacements (MASD) results using MD, the addition of Al makes the appearance of severe localized lattice distortions, while the addition of Fe tends to form short-range ordered structures. In summary, fine-grain strengthening and the hardness strengthening caused by local lattice distortion were the main strengthening mechanisms of AlCoCrFeNi. These findings are highly significant for expanding the application potential and provide profound insights into the wear properties of the CoCrNi MEA coatings. Full article