Search Results (529)

The precursor-derived ceramic route is recognized as an advanced and efficient technique for fabricating ceramic matrix composites, particularly suitable for the development and microstructural tailoring of continuous fiber-reinforced ceramic matrix composites. In this work, octamethylcyclotetrasiloxane and tetravinylcyclotetrasiloxane were employed as monomers to synthesize a branched siloxane via ring-opening polymerization. A subsequent hydrosilylation reaction led to the formation of polyvinylsiloxane with a three-dimensional crosslinked structure. The precursor exhibited excellent fluidity, adjustable viscosity, and superior thermosetting characteristics, enabling efficient impregnation and densification of reinforcements through the polymer infiltration and pyrolysis process. Upon pyrolysis, the polyvinylsiloxane gradually converted from an organic polymer to an amorphous inorganic ceramic phase, yielding silicon oxycarbide ceramics with a high ceramic yield of 81.3%. Elemental analysis indicated that the resulting ceramic mainly comprised silicon and oxygen, with a low carbon content. Furthermore, the material demonstrated a stable dielectric constant (~2.5) and low dielectric loss (<0.01), which are beneficial for enhanced thermal stability and dielectric performance. These findings offer a promising precursor system and process reference for the low-cost production of high-performance, multifunctional ceramic matrix composites with strong potential for engineering applications. Full article

Agricultural nondestructive testing technology is pivotal in safeguarding food quality assurance, safety monitoring, and supply chain transparency. While conventional optical methods such as near-infrared spectroscopy and hyperspectral imaging demonstrate proficiency in surface composition analysis, their constrained penetration depth and environmental sensitivity limit effectiveness in dynamic agricultural inspections. This review highlights the transformative potential of microwave technologies, systematically examining their operational principles, current implementations, and developmental trajectories for agricultural quality control. Microwave technology leverages dielectric response mechanisms to overcome traditional limitations, such as low-frequency penetration for grain silo moisture testing and high-frequency multi-parameter analysis, enabling simultaneous detection of moisture gradients, density variations, and foreign contaminants. Established applications span moisture quantification in cereal grains, oilseed crops, and plant tissues, while emerging implementations address storage condition monitoring, mycotoxin detection, and adulteration screening. The high-frequency branch of the microwave–millimeter wave systems enhances analytical precision through molecular resonance effects and sub-millimeter spatial resolution, achieving trace-level contaminant identification. Current challenges focus on three areas: excessive absorption of low-frequency microwaves by high-moisture agricultural products, significant path loss of microwave high-frequency signals in complex environments, and the lack of a standardized dielectric database. In the future, it is essential to develop low-cost, highly sensitive, and portable systems based on solid-state microelectronics and metamaterials, and to utilize IoT and 6G communications to enable dynamic monitoring. This review not only consolidates the state-of-the-art but also identifies future innovation pathways, providing a roadmap for scalable deployment of next-generation agricultural NDT systems. Full article

Benzoxazine resins are gaining attention for their impressive thermal stability, low water uptake, and strong mechanical properties. In this work, two new bio-based benzoxazine monomers were developed using renewable arbutin: one combined with 3-(2-aminoethylamino) propyltrimethoxysilane (AB), and the other with furfurylamine (AF). Both were synthesized using a simple Mannich-type reaction and verified through FT-IR and ¹H-NMR spectroscopy. By blending these monomers in different ratios, copolymers with adjustable thermal, dielectric, and surface characteristics were produced. Thermal analysis showed that the materials had broad processing windows and cured effectively, while thermogravimetric testing confirmed excellent heat resistance—especially in AF-rich blends, which left behind more char. The structural changes obtained during curing process were monitored using FT-IR, and XPS verified the presence of key elements like carbon, oxygen, nitrogen, and silicon. SEM imaging revealed that AB-based materials had smoother surfaces, while AF-based ones were rougher; the copolymers fell in between. Dielectric testing showed that increasing AF content raised both permittivity and loss, and contact angle measurements confirmed that surfaces ranged from water-repellent (AB) to water-attracting (AF). Overall, these biopolymers (AB/AF copolymers) synthesized from arbutin combine environmental sustainability with customizability, making them strong candidates for use in electronics, protective coatings, and flame-resistant composite materials. Full article

Pyrochlore Bi_1.8Mn_0.5Ni_0.5Ta₂O_9-Δ (sp.gr. Fd-3m, a = 10.5038(9) Å) was synthesized by the solid-phase reaction method and characterized by vibrational and X-ray spectroscopy. According to scanning electron microscopy, the ceramics are characterized by a porous microstructure formed by randomly oriented oblong grains. The average crystallite size determined by X-ray diffraction is 65 nm. The charge state of transition element cations in the pyrochlore was analyzed by soft X-ray spectroscopy using synchrotron radiation. For mixed pyrochlore, a characteristic shift of Bi4f and Ta4f and Ta5p spectra to the region of lower energies by 0.25 and 0.90 eV is observed compared to the binding energy in Bi₂O₃ and Ta₂O₅ oxides. XPS Mn2p spectrum of pyrochlore has an intermediate energy position compared to the binding energy in MnO and Mn₂O₃, which indicates a mixed charge state of manganese (II, III) cations. Judging by the nature of the Ni2p spectrum of the complex oxide, nickel ions are in the charge state of +(2+ζ). The relative permittivity of the sample in a wide temperature (up to 350 °C) and frequency range (25–10⁶ Hz) does not depend on the frequency and exhibits a constant low value of 25. The minimum value of 4 × 10⁻³ dielectric loss tangent is exhibited by the sample at a frequency of 10⁶ Hz. The activation energy of conductivity is 0.7 eV. The electrical behavior of the sample is modeled by an equivalent circuit containing a Warburg diffusion element. Full article

The escalating consumption of fossil fuels and the rapid development of portable electronics have increased interest in alternative energy solutions that can sustainably self-power wearable devices. Triboelectric nanogenerators (TENGs), which convert mechanical energy into electricity through contact electrification and electrostatic induction, have emerged as a promising technology due to their high voltage output, lightweight design, and simple fabrication. However, the performance of TENGs is often limited by a low surface charge density, inadequate dielectric properties, and poor charge retention of triboelectric materials. To address these challenges, recent research has focused on the use of polymer composites that incorporate various functional fillers. The filler materials play roles in improving dielectric performance and enhancing mechanical durability, thereby boosting triboelectric output even in harsh environments, while also diminishing charge loss. This review comprehensively examines the role of polymer composite design in TENG performance, with particular emphasis on materials categorized by their triboelectric polarity. Tribo-negative polymers, such as PDMS and PVDF, benefit from filler incorporation and phase engineering to enhance surface charge density and charge retention. By contrast, tribo-positive materials like nylon and cellulose have demonstrated notable improvements in mechanical robustness and environmental stability through composite strategies. The interplay between material selection, surface engineering, and filler design is highlighted as a critical path toward developing high-performance, self-powered TENG systems. Finally, this review discusses the current challenges and future opportunities for advancing TENG technology toward practical and scalable applications. Full article

Linear passive electrical devices/components are usually characterized in the frequency domain by their impedance, i.e., the ratio of the voltage and current phasors. The use of the impedance concept does not raise particular concerns in low-frequency regimes; however, things become more complicated when it comes to rapid time-varying phenomena, mainly because the voltage depends not only on the position of the points between which it is defined but also on the choice of the integration path that connects them. In this article, based on first principles (Maxwell equations and Poynting vector flow considerations), we discuss the concept of impedance and define it unequivocally for a class of electrical devices/components with rotational symmetry. Two application examples are presented and discussed. One simple example concerns the per-unit-length impedance of a homogeneous cylindrical wire subject to the skin effect. The other, which is more elaborate, concerns a heterogeneous structure that consists of a dielectric disk sandwiched between two metal plates. For the lossless situation, the high-frequency impedance of this device (circular parallel plate capacitor) reaches zero when the frequency reaches a certain critical frequency f_c; then, it becomes inductive and increases enormously when the frequency reaches another critical frequency at 1.6 f_c. The influence of losses on the impedance of the device is thoroughly investigated and evaluated. Impedance corrections due to dielectric losses are analyzed using a frequency-dependent Debye permittivity model. The impedance corrections due to plate losses are analyzed by considering radial current distributions on the outer and inner surfaces of the plates, the latter exhibiting significant variations near the critical frequencies of the device. Full article

This paper proposes a broadband and high-efficiency anomalous reflection device based on a dielectric catenary metasurface, addressing the bottleneck problems of low efficiency and narrow bandwidth in traditional discrete metasurfaces. By designing a silicon-based equal-strength catenary structure, the efficient control of circularly polarized light beams within a wide angular range in the infrared band has been achieved. Simulation results show that the designed metasurface exhibits excellent beam steering performance when the deflection angle reaches 65°. Furthermore, to characterize the diffraction efficiency of the metasurface within a large angular range, the results indicate that under oblique incidence (0–60°), the diffraction efficiency of the ±1st order exceeds 80%, and the undesired higher-order diffractions are significantly suppressed. This ultrahigh working efficiency is attributed to the nearly perfect polarization conversion and continuous phase profile of the dielectric catenary structure. By combining catenary optics with the low-loss properties of the dielectric material, this design provides a new solution for the design of efficient, broadband, and wide-angle planar optical devices. Full article

Low-permittivity microwave dielectric ceramics are essential for high-frequency communication and radar systems, as they minimize signal delay and interference, thereby enabling compact and high-performance devices. In this study, LiAl_5−xNi_xO_8−0.5x (x = 0.1–0.5) ceramics were synthesized via a solid-state reaction method to investigate the effects of Ni²⁺ substitution on crystal structure, microstructure, and dielectric properties. X-ray diffraction and Rietveld refinement reveal a phase transition from the P4₃32 to the Fd$\stackrel{-}{3}$m spinel structure at x ≈ 0.3, accompanied by a systematic increase in the lattice parameter (7.909–7.975 Å), attributed to the larger ionic radius of Ni²⁺ compared to Al³⁺. SEM analysis confirms dense microstructures with relative densities exceeding 95% and grain size increases from less than 1 μm at x = 0.1 to approximately 2 μm at x = 0.5. Dielectric measurements show a decrease in permittivity (ε_r) from 8.24 to 7.77 and in quality factor (Q × f) from 34,605 GHz to 20,529 GHz with increasing Ni content, while the temperature coefficient of the resonant frequency (τ_f) shifts negatively from −44.8 to −69.1 ppm/°C. Impedance spectroscopy indicates increased conduction losses and reduced activation energy with higher Ni²⁺ concentrations. Full article

Microwave dielectric ceramics are indispensable in modern communication technologies, playing a pivotal role in components such as filters, oscillators, and antennas. Among these materials, ZnAl₂O₄ ceramics have garnered attention for their excellent quality factor (Q × f) and low dielectric constant (ε_r). However, their high sintering temperature (~1650 °C) limits practical applications. This study investigates ZnAl_2-x(Zn_0.5Si_0.5)_xO₄ (ZAZS) (x = 0.1–0.9) ceramics, where [Zn_0.5Si_0.5]³⁺ substitutes Al³⁺, to reduce sintering temperature while maintaining high-performance microwave dielectric properties. ZAZS ceramics were synthesized via the solid-state reaction method and characterized for their structural, morphological, and dielectric properties. X-ray diffraction analysis confirmed the formation of a single-phase solid solution up to x = 0.8, with minor secondary phases appearing at x = 0.9. The substitution increased lattice parameters and enhanced material densification, as observed through SEM and relative density calculations. Microwave dielectric measurements showed that ZAZS ceramics achieved a maximum Q × f of 20,200 GHz and a τ_f value reduced to −62 ppm/°C at x = 0.8, while ε_r decreased from 7.90 to 6.98. Bond-valence calculations reveal that the reduction of the average Al/Zn/Si–O bond valence weakens octahedral rigidity, systematically tuning τ_f toward zero. These results demonstrate that ZAZS ceramics, with a reduced sintering temperature of 1400 °C, exhibit excellent potential for application in low-loss microwave devices. Full article

Polymer composites with high dielectric permittivity (>10) and low dielectric loss are critical for energy storage and microelectronic applications. This study reports on a semi-transparent composite of a PVDF copolymer filled with Cu₇S₄ nanoparticles synthesized via a wet chemical route. Only a small content (6%) of copper sulfide increases the dielectric permittivity of the material from 10.4 to 15.9 (1 kHz), maintaining a low dielectric loss coefficient (less than 0.1). The incorporated nanoparticles affect the morphology of the composite film surface and crystalline phases in the whole volume, which was studied with FTIR spectroscopy, differential scanning calorimetry and scanning probe microscopy. Full article

This study presents a novel, eco-friendly synthesis route for zinc oxide (ZnO) nanoparticles using cladode extracts of Hylocereus undatus acting simultaneously as reducing and improving agents, in alignment with green chemistry principles. The synthesis involved the reaction of zinc sulfate heptahydrate with the plant extract, with the medium pH adjusted using sodium hydroxide (NaOH), followed by calcination at 300 °C, 400 °C, and 500 °C, and then by a washing step to enhance purity. Comprehensive characterization was performed using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrical impedance spectroscopy to investigate the structural, morphological, and dielectric properties of the nanoparticles. The sample calcined at 400 °C, followed by washing (HT400W), exhibits highly crystalline ZnO nanoparticles with a predominant wurtzite structure (93.15 wt% ZnO) and minimal impurities (6.85 wt% Na₂SO₄). SEM analysis indicated a flake-like morphology with nanoscale features (50–100 nm), while Raman spectroscopy confirmed enhanced crystallinity and purity post-washing. Additionally, the HT400W sample exhibited a dielectric constant (ε′) of 16.96 and a low loss tangent (tan δ) of 0.14 at 1 MHz, suggesting superior energy efficiency for high-frequency applications. This green synthesis approach not only eliminates hazardous reagents but also delivers ZnO nanoparticles with good dielectric performance. Furthermore, this work demonstrates the efficacy of a sustainable biotemplate, offering an environmentally friendly approach for synthesizing ZnO nanoparticles with tailored physicochemical properties. Full article

Polytetrafluoroethylene (PTFE) has been widely used as a high-frequency dielectric substrate due to its excellent dielectric properties and thermal stability. However, with its low intrinsic thermal conductivity, PTFE falls short in meeting the escalating heat dissipation demands of high-power density, high-frequency communication systems. Although the thermal conductivity of PTFE composites can be effectively improved by the high thermal conductivity fillers, it is always accompanied by a decline in dielectric properties. Molecular chain ordering is regarded as an effective strategy to improve the intrinsic thermal conductivity of polymers while maintaining dielectric properties. Unfortunately, the conventional preparation methods for ordered molecular chains, such as electrostatic spinning and uniaxial stretching, are not applicable to the preparation of PTFE substrates. In this work, fluorinated graphite (FGi) is employed to induce the in-plane orientation of PTFE molecular chains. As a result, the PTFE composite with 0.5 wt% FGi loading exhibits an in-plane thermal conductivity of 1.21 W·m⁻¹·K⁻¹, six times higher than the in-plane thermal conductivity of pure PTFE. In addition, this composite exhibits a superior dielectric constant of 2.06 and dielectric loss of 0.0021 at 40 GHz. This work introduces a facile method to achieve improved thermal conductivity of PTFE while maintaining its excellent dielectric properties. Full article

In this paper, the optical properties and lattice thermal conductivity of Ti₂AlB₂ were studied by first-principles calculations. The real part of the dielectric constant, ε₁, attains a significant value of 47.26 at 0.12 eV, indicating strong polarization capabilities and energy storage capacity. Regarding optical properties, Ti₂AlB₂ exhibits significant absorption peaks at photon energies of 4.19 eV, 6.78 eV, and 10.61 eV, and 14.32 eV, with absorption coefficients of 184,168.1 cm⁻¹, 228,860.8 cm⁻¹, 366,350.8 and 303,440.6 cm⁻¹, indicating a strong absorption capacity. The loss function exhibits peaks at 19.80 eV and the refractive index reaches a maximum of 8.30 at 0.01 eV. Reflectivity is notably higher in the 0–5 eV range, exceeding 44%, which demonstrates excellent reflective properties. This suggests that Ti₂AlB₂ has potential as an optical coating material across certain frequency bands. The lattice thermal conductivity of Ti₂AlB₂ is obtained at 27.2 W/(m·K). The phonon relaxation time is greater in the low-frequency region, suggesting that phonons have a longer duration of action during the heat transport process, which may contribute to higher thermal conductivity. Although the phonon group velocity is generally low, several factors influence thermal conductivity, including phonon relaxation time and Grüneisen parameters. The high Grüneisen parameter of Ti₂AlB₂ indicates strong anharmonic vibrations, which may enhance phonon scattering and consequently reduce thermal conductivity. However, Ti₂AlB₂ still exhibits some lattice thermal conductivity, suggesting that the contributions of phonon relaxation time and group velocity to its thermal conductivity may be more significant. The unique optical properties and thermal conductivity of Ti₂AlB₂ indicate its potential applications in optical coatings and high-temperature structural materials. Full article

Cross-linked polyethylene (XLPE) cables will gradually experience aging under various stresses during long-term operation, which may lead to faults and seriously affect the safe and stable operation of the power system. This article prepares aged cable samples by accelerating the thermal aging of XLPE cables, and combines frequency-domain dielectric spectroscopy (FDS) and the polarization–depolarization current method (PDC) for detection and analysis. By measuring the dielectric loss of aged cables using frequency-domain dielectric spectroscopy, it was found that the dielectric loss value in the low-frequency region significantly increases with aging time, indicating that aging leads to an increase in polarity groups and polarization loss. The high-frequency dielectric loss also significantly increases with the strengthening of dipole polarization. At the same time, using the polarization–depolarization current method to measure the polarization current and depolarization current of cables, it was found that the stable value of polarization current increases with aging time, further verifying the changes in the conductivity and polarization characteristics of insulation materials. Combining the broadband dielectric response characteristics of FDS (0.001 Hz–1 kHz) with the time-domain charge transfer analysis of PDC, the molecular structure degradation (dipole polarization enhancement) and interface defect accumulation (space charge effect) of cable aging are revealed from both frequency- and time-domain perspectives. The experimental results show that the integral value of the low-frequency region of the frequency-domain dielectric spectrum and the stable value of the polarization depolarization current are positively correlated with the aging time, and can make use of effective indicators to evaluate the aging state of XLPE cables. Full article

Highly heat-resistant and low-dielectric materials are crucial for achieving high-frequency communication, high-density integration, and high-temperature stability in modern electronics. In this work, surface modification of hollow silica microspheres (HGMs) using a silane coupling agent ((3-aminopropyl)triethoxysilane, KH550) yielded KHGM particles with a coating content of approximately 9.3 wt%, which were subsequently incorporated into high-performance polyarylene ether nitrile (PEN) polymers to fabricate composite films. The modified nanoparticles demonstrated significantly enhanced compatibility with the polymer matrix, while their hollow structure effectively reduced the dielectric constant of the composite film. When loaded with 50 wt% KHGM particles, the PEN-based composite film exhibited an elevated glass transition temperature of 198 °C and achieved a dielectric constant as low as 2.32 at 1 MHz frequency, coupled with dielectric loss below 0.016; compared with pure PEN, the dielectric constant of PEN/KHGM-50% decreased by 26.47%. Additionally, the composite demonstrated excellent water repellency. These advancements provide high-performance material support for applications in electronic communications, aerospace, and related fields. Full article