Search Results (26)

The lateral flow immunoassay (LFIA) is a widely utilized, rapid diagnostic technique characterized by its short analysis duration, cost efficiency, visual result interpretation, portability and suitability for point-of-care applications. However, conventional LFIAs have limited sensitivity, a challenge that can be overcome by the introduction of gold nanoparticles, which provide enhanced sensitivity and selectivity (compared, for example, to latex beads or carbon nanoparticles) for the detection of target analytes, due to their optical properties, chemical stability and ease of functionalization. In this work, gold nanoparticle-based LFIAs are developed for the detection of aflatoxin B1, and the relative performance of different morphology particles is evaluated. LFIA using gold nano-labels allowed for aflatoxin B1 detection over a range of 0.01 ng/mL–100 ng/mL. Compared to spherical gold nanoparticles and gold nano-flowers, star-shaped gold nanoparticles show increased antibody binding efficiency of 86% due to their greater surface area. Gold nano-stars demonstrated the highest sensitivity, achieving a limit of detection of 0.01ng/mL, surpassing the performance of both spherical gold nanoparticles and gold nano-flowers. The use of star-shaped particles as nano-labels has demonstrated a five-fold improvement in sensitivity, underscoring the potential of integrating diverse nanostructures into LFIA for significantly improving analyte detection. Moreover, the robustness and feasibility of gold nano-stars employed as labels in LFIA was assessed in detecting aflatoxin B1 in a wheat matrix. Improved sensitivity with gold nano-stars holds promise for applications in food safety monitoring, public health diagnostics and rapid point-of-care diagnostics. This work opens the pathway for further development of LFIA utilizing novel nanostructures to achieve unparallel precision in diagnostics and sensing. Full article

Direct ink writing (DIW) is an economical, straightforward, and relatively energy-efficient 3D printing technique that has been used in various domains. However, the utilization of rubber latex for DIW remains limited due to its high fluidity and inadequate support, which makes it challenging to meet the required ink rheological characteristics for DIW. In this study, a concentrated pre-vulcanized natural rubber latex (CPNRL) ink with a high solid content of 73% without additives is developed for DIW 3D printing. The CPNRL ink is concentrated using superabsorbent polymer (SAP) beads, which demonstrates good colloidal stability, favorable rheological properties, and superior printability. The impact of printing angles on the mechanical properties of the rubber specimens based on the CPNRL-73 ink is explored in detail, wherein the tensile strength of the specimen printed at a 90° angle reaches an impressive 26 MPa and a strain of approximately 800%, which surpasses the majority of 3D-printed rubber latex specimens. Additionally, the CPNRL ink can be used to print a wide range of intricate shapes, demonstrating its advantages in excellent formability. The preparation of 3D printable ink using the absorption method will expand the application of elastomers in fields such as customized flexible sensing and personalized rubber products. Full article

The photochemical degradation of natural rubber (NR) is a prevalent method used to modify its inherent properties. Natural rubber, predominantly derived from the Hevea Brasiliensis tree, exhibits an exceptionally high molecular weight (MW), often reaching a million daltons (Da). This high MW restricts its solubility in various solvents and its reactivity with polar compounds, thereby constraining its versatile applications. In our previous work, we employed TiO₂ in its powdered form as a photocatalyst for the functionalization of NR latex. However, the post-process separation and reuse of this powder present substantial challenges. In this present study, we aimed to functionalize deproteinized NR (DPNR) latex. We systematically reduced its MW via photochemical degradation under UVA irradiation facilitated by H₂O₂. To enhance the efficiency of the degradation process, we introduced TiO₂-coated hollow glass beads (TiO₂-HGBs) as photocatalysts. This approach offers the advantage of easy collection and repeated reuse. The modified DPNR showed a reduction in its number-average MW from 9.48 × 10⁵ to 0.28 × 10⁵ Da and incorporated functional groups, including hydroxyl, carbonyl, and epoxide. Remarkably, the TiO₂-HGBs maintained their performance over seven cycles of reuse. Due to their superior efficacy, TiO₂-HGBs stand out as promising photocatalysts for the advanced functionalization of NR across various practical applications. Full article

Surveillance of viral pathogens in both point-of-care and clinical settings is imperative to preventing the widespread propagation of disease—undetected viral outbreaks can pose dire health risks on a large scale. Thus, portable, accessible, and reliable biosensors are necessary for proactive measures. Polymeric microparticles have recently gained popularity for their size, surface area, and versatility, which make them ideal biosensing tools. This review cataloged recent investigations on polymeric microparticle-based detection platforms across eight virus families. These microparticles were used as labels for detection (often with fluorescent microparticles) and for capturing viruses for isolation or purification (often with magnetic microparticles). We also categorized all methods by the characteristics, materials, conjugated receptors, and size of microparticles. Current approaches were compared, addressing strengths and weaknesses in the context of virus detection. In-depth analyses were conducted for each virus family, categorizing whether the polymeric microparticles were used as labels, for capturing, or both. We also summarized the types of receptors conjugated to polymeric microparticles for each virus family. Full article

Autophagy is a process that promotes the lysosomal degradation of cytoplasmic proteins and is highly conserved in eukaryotic organisms. Autophagy maintains homeostasis in organisms and regulates multiple developmental processes, and autophagy disruption is related to human diseases. However, the functional roles of autophagy in mediating innate immune responses are largely unknown. In this study, we sought to understand how Atg2, an autophagy-related gene, functions in the innate immunity of Drosophila melanogaster. The results showed that a large number of melanotic nodules were produced upon inhibition of Atg2. In addition, inhibiting Atg2 suppressed the phagocytosis of latex beads, Staphylococcus aureus and Escherichia coli; the proportion of Nimrod C1 (one of the phagocytosis receptors)-positive hemocytes also decreased. Moreover, inhibiting Atg2 altered actin cytoskeleton patterns, showing longer filopodia but with decreased numbers of filopodia. The expression of AMP-encoding genes was altered by inhibiting Atg2. Drosomycin was upregulated, and the transcript levels of Attacin-A, Diptericin and Metchnikowin were decreased. Finally, the above alterations caused by the inhibition of Atg2 prevented flies from resisting invading pathogens, showing that flies with low expression of Atg2 were highly susceptible to Staphylococcus aureus and Erwinia carotovora carotovora 15 infections. In conclusion, Atg2 regulated both cellular and humoral innate immunity in Drosophila. We have identified Atg2 as a crucial regulator in mediating the homeostasis of immunity, which further established the interactions between autophagy and innate immunity. Full article

Producing specific antibodies in chickens is an attractive approach for diagnosis or therapeutic applications. Besides the high immunoglobulin Y (IgY) yield transferred to the egg yolk and its suitability for large-scale production, such an approach is more bioethical for animal maintenance. The IgY technology offers new possibilities for application in human and veterinary diagnostics and therapeutics, including strategies for treating severe intestinal diseases in children, particularly in emerging countries. Herein, we describe the production and purification of polyclonal antibodies against rotavirus group A (RVA) in immunised hens aiming at its application in prophylaxis and treatment of rotavirus-induced diarrhoea. For this purpose, we inoculated Rhodia laying chickens (Gallus gallus domesticus) with two or three doses of RVA combined with adjuvants or only adjuvants (control group). As the egg-laying period began, the yolk protein purification processes yielded a high concentration of specific IgY, the highest titre resulting from the group of hens that received three doses of the immunogen. The purified IgY blocked the functional activity of RVA in MA-104 cells, thus confirming the neutralisation ability. Therefore, anti-RVA IgY could be a promising candidate for pre- and post-exposure prevention or treatment of rotavirus-induced diarrhoea. Full article

Hemophagocytic lymphohistiocytosis (HLH) is a life-threatening hyperinflammatory syndrome characterized by prolonged fever, cytopenia, hepatosplenomegaly, and hemophagocytosis. This occurs as a result of activated macrophages and impaired function of natural killer cells and/or cytotoxic T lymphocytes. The NF-κB pathway plays a crucial role in hyperinflammation. Matrin3 (MATR3) is a nuclear RNA/DNA-binding protein that plays multiple roles in the regulation of gene expression. We enroll 62 patients diagnosed with secondary HLH and hemophagocytosis. Peripheral blood (PB) from 25 patients and 30 healthy volunteers and good quality bone marrow (BM) samples from 47 patients are collected and used for analysis. Clinical parameters, including age, sex, etiology, ferritin, fibrinogen, triglyceride, and viral infection status, had no association with survival prediction. Patients with downregulation of NF-κB and MATR3mRNA expression in the BM had a higher mortality rate. MATR3mRNA expression in PB was lower in patients compared to that in healthy volunteers. We use shRNA-MATR3-KD-THP1 cells to determine the efficacy of phagocytosis. We note that shRNA-MATR3-KD-THP1 cells had a higher phagocytic effect on necrotic Jurkat E6 cells and carboxylate modified polystyrene latex beads. Herein, we provide evidence of a new marker for clinical translation that can serve as a potential treatment target for secondary HLH. Full article

Coronary stenosis has been one of the most common heart diseases that drastically increases the risk of fatal disorders such as heart attack. Angioplasty using drug coated balloons (DCB) has been one of the most safe and promising treatments. To minimize the risk of thrombosis of such DCBs during intervention, a different approach that can secure high hemocompatibility under blood flow is necessary. Here we report a method of improving the photoresponsive platform’s hemocompatibility by conjugating polyethylene glycol (PEG), onto the functional groups located at the balloon surface. In this study, latex microbeads were used as models for balloons to enable precise observation of its surface under microscopy. These beads were decorated with PEG polymers of a variety of lengths and grafting densities, along with the Cy5-Photoclevable (PC) linker conjugate to mimic drugs to be loaded onto the platform. Results showed that PEG length and grafting density are both critical factors that alter not only its hemocompatibility, but also the drug load and release efficiency of such platform. Thus, although further investigation is necessary to optimize the tradeoff between hemocompatibility, drug load, and release efficiency, it is safe to conclude that PEGylation of DCB surface is an effective method of enhancing and maintaining high hemocompatibility to minimize the risk of thrombosis during angioplasty. Full article

The present work describes the phenomenological approach to automatically determine the frequency range for positive and negative dielectrophoresis (DEP)—an electrokinetic force that can be used for massively parallel micro- and nano-assembly. An experimental setup consists of the microfabricated chip with gold microelectrode array connected to a function generator capable of digitally controlling an AC signal of 1 V (peak-to-peak) and of various frequencies in the range between 10 kHz and 1 MHz. The suspension of latex microbeads (3-μm diameter) is either attracted or repelled from the microelectrodes under the influence of DEP force as a function of the applied frequency. The video of the bead movement is captured via a digital camera attached to the microscope. The OpenCV software package is used to digitally analyze the images and identify the beads. Positions of the identified beads are compared for successive frames via Artificial Intelligence (AI) algorithm that determines the cloud behavior of the microbeads and algorithmically determines if the beads experience attraction or repulsion from the electrodes. Based on the determined behavior of the beads, algorithm will either increase or decrease the applied frequency and implement the digital command of the function generator that is controlled by the computer. Thus, the operation of the study platform is fully automated. The AI-guided platform has determined that positive DEP (pDEP) is active below 500 kHz frequency, negative DEP (nDEP) is evidenced above 1 MHz frequency and the crossover frequency is between 500 kHz and 1 MHz. These results are in line with previously published experimentally determined frequency-dependent DEP behavior of the latex microbeads. The phenomenological approach assisted by live AI-guided feedback loop described in the present study will assist the active manipulation of the system towards the desired phenomenological outcome such as, for example, collection of the particles at the electrodes, even if, due to the complexity and plurality of the interactive forces, model-based predictions are not available. Full article

The detection limit of lateral flow immunoassay (LFIA) is largely determined by the properties of the label used. We compared four nanoparticle labels differing in their chemical composition and colour: (1) gold nanoparticles (Au NPs), red; (2) Au-core/Pt-shell nanoparticles (Au@Pt NPs), black; (3) latex nanoparticles (LPs), green; and (4) magnetic nanoparticles (MPs), brown. The comparison was carried out using one target analyte—Erwinia amylovora, the causal bacterial agent of fire blight. All nanoparticles were conjugated with antibodies through methods that provide maximum functional coverage like physical adsorption (Au NPs, Au@Pt NPs) and covalent bonding (LPs, MPs). All conjugates demonstrated the same ability to bind with E. amylovora through enzyme-linked immunosorbent assay where optical properties of the nanoparticles do not determine the registered signal. However, half-maximal binding was achieved at different numbers of nanoparticles because they differ in size. All conjugates based on four nanoparticle labels were used for lateral flow assays. As a result, Au@Pt NPs provided the minimal detection limit that corresponded to 10³ CFU/mL. Au NPs and LPs detected 10⁴ CFU/mL, and MPs detected 10⁵ CFU/mL. The results highlight that simply choosing a coloured label can significantly affect the detection limit of LFIA. Full article

It is well known that living cells interact mechanically with their microenvironment. Many basic cell functions, like migration, proliferation, gene expression, and differentiation, are influenced by external forces exerted on the cell. That is why it is extremely important to study how mechanical properties of the culture substrate influence the cellular molecular regulatory pathways. Optical microscopy is one of the most common experimental method used to visualize and study cellular processes. Confocal microscopy allows to observe changes in the 3D organization of the cytoskeleton in response to a precise mechanical stimulus applied with, for example, a bead trapped with optical tweezers. Optical tweezers-based method (OT) is a microrheological technique which employs a focused laser beam and polystyrene or latex beads to study mechanical properties of biological systems. Latex beads, functionalized with a specific protein, can interact with proteins located on the surface of the cellular membrane. Such interaction can significantly affect the cell’s behavior. In this work, we demonstrate that beads alone, placed on the cell surface, significantly change the architecture of actin, microtubule, and intermediate filaments. We also show that the observed molecular response to such stimulus depends on the duration of the cell–bead interaction. Application of cytoskeletal drugs: cytochalasin D, jasplakinolide, and docetaxel, abrogates remodeling effects of the cytoskeleton. More important, when cells are plated on elastic substrates, which mimic the mechanical properties of physiological cellular environment, we observe formation of novel, “cup-like” structures formed by the microtubule cytoskeleton upon interaction with latex beads. These results provide new insights into the function of the microtubule cytoskeleton. Based on these results, we conclude that rigidity of the substrate significantly affects the cellular processes related to every component of the cytoskeleton, especially their architecture. Full article

This review describes and appraises a novel protein-based antigen detection test for visceral leishmaniasis (VL). The test detects in patient’s urine six proteins from Leishmania infantum (chagasi) and Leishmania donovani, the etiological agents of VL. The gold standard test for VL is microscopic observation of the parasites in aspirates from spleen, liver, or bone marrow (and lymph node for dogs). Culture of the parasites or detection of their DNA in these aspirates are also commonly used. Serological tests are available but they cannot distinguish patients with active VL from either healthy subjects exposed to the parasites or from subjects who had a successful VL treatment. An antigen detection test based on the agglutination of anti-leishmania carbohydrates antibody coated latex beads has been described. However, the results obtained with this carbohydrate-based test have been conflicting. Using mass spectrometry, we discovered six L. infantum/L. donovani proteins excreted in the urine of VL patients and used them as markers for the development of a robust mAb-based antigen (protein) detection test. The test is assembled in a multiplexed format to simultaneously detect all six markers. Its initial clinical validation showed a sensitivity of 93% and specificity of 100% for VL diagnosis. Full article

Viral infections in humans cause a huge burden in worldwide healthcare that has increased due to the emergence of new pathogenic viruses, such as in the recent Ebola virus (EBOV) outbreaks. Viral particles in body fluids are often at very low levels, making diagnosis difficult. In order to address this problem, we have developed a new detection platform to isolate and detect different enveloped viruses. We have recently identified that sialic acid-binding Ig‑like lectin 1 (Siglec-1/CD169) is one cellular receptor used by EBOV and HIV-1 to enter myeloid cells, key target cells for infection and pathogenesis. For viral uptake, the V-set domain of this myeloid cell receptor recognizes the gangliosides of viral membranes that were dragged during viral budding from the plasma membrane of infected cells. We took advantage of this specific interaction between Siglec‑1 and viral gangliosides to develop a new detection methodology. We have generated a recombinant protein that contains the V-set domain of Siglec-1 fused to the human IgG Fc domain for anchoring in latex beads. These coated beads allow the isolation of viral particles and their measurement by flow cytometry. We have tested its efficacy to detect HIV-1 and EBOV and its specificity by using anti-Siglec‑1 antibodies that prevent the interaction and serve as a negative control. To test the capacity of our method, we used synthetic liposomes to assess the effect of ganglioside concentration in membranes as well as the size of viral particles. This methodology would facilitate the diagnosis of infections by concentrating viral particles in a fast and direct method. At a time when global human mobility facilitates the dissemination of infectious agents, our approach represents a rapid and effective method to maximize the identification of both known and emerging enveloped viruses as part of public health viral surveillance strategies. Full article

We evaluated two concentrating techniques that could be used to improve bioaerosol detection and quantification: A BioChromato Smart Evaporator C1 (BioChromato, Inc.) and two Concentrating Pipette (CP) models (CP-150 and CP-Select) (InnovaPrep, LLC). We determined the concentration factor (CF) (the concentration of particles in the final solution compared to the concentration in the initial solution) and the particle losses when processing the samples with polystyrene latex (PSL) beads and different species of bacteria. When processing total particles, regardless of the culturability status, the losses for the Evaporator were 3.70–23.89%; for the CP-models, the losses ranged from 0.20% to 67.22%. For the culturable particles processed with the CP devices, the losses ranged from 42.85% to 90.19% and were higher for Gram-negative pseudomonads compared to Gram-positive B. subtilis. Despite the loss of particles, both devices yielded more concentrated final solutions. The CF for the Evaporator was 3.59–10.92; the CF values for the CP devices ranged from 55.77 to 184.64 for total particles and from 6.29 to 96.52 for culturable bacteria. This higher CF was mainly achieved due to lower final suspension volumes. The study demonstrated that the two concentrators can improve particle detection, but that one should take particle losses into account. Full article

A new generation of magnetic lateral flow immunoassays is emerging as powerful tool for diagnostics. They rely on the use of magnetic nanoparticles (MNP) as detecting label, replacing conventional gold or latex beads. MNPs can be sensed and quantified by means of external devices, allowing the development of immunochromatographic tests with a quantitative capability. Moreover, they have an added advantage because they can be used for immunomagnetic separation (IMS), with improvements in selectivity and sensitivity. In this paper, we have reviewed the current knowledge on magnetic-lateral flow immunoassay (LFIA), coupled with both research and commercially available instruments. The work in the literature has been classified in two categories: optical and magnetic sensing. We have analysed the type of magnetic nanoparticles used in each case, their size, coating, crystal structure and the functional groups for their conjugation with biomolecules. We have also taken into account the analytical characteristics and the type of transduction. Magnetic LFIA have been used for the determination of biomarkers, pathogens, toxins, allergens and drugs. Nanocomposites have been developed as alternative to MNP with the purpose of sensitivity enhancement. Moreover, IMS in combination with other detection principles could also improve sensitivity and limit of detection. The critical analysis in this review could have an impact for the future development of magnetic LFIA in fields requiring both rapid separation and quantification. Full article