Search Results (72)

Though the pursuit of sustainable desalination processes with high water recovery has intensified the research interest in membrane distillation (MD), the influence of module connection configuration on performance stability remains poorly explored. The current study provided a comprehensive multiparameter assessment of hollow fibre membrane modules connected in parallel and series in direct contact membrane distillation (DCMD) for the first time. The configurations were evaluated under varying process parameters such as temperature (50–70 °C), flow rates (22.1–32.3 mL·s⁻¹), magnesium concentration as scalant (1.0–4.0 g·L⁻¹), and flow direction (co-current and counter-current), assessing their influence on temperature gradients (∆T), flux and pH stability, salt rejection, and crystallisation. Interestingly, the parallel module configuration maintained high operational stability with uniform flux and temperature differences (∆T) even at high recovery factors (>75%). On one hand, the serial configuration experienced fluctuating ∆T caused by thermal and concentration polarisation, causing an early crystallisation (abrupt drop in feed conductivity). Intensified polarisation effects with accelerated crystallisation increased the membrane risk of wetting, particularly at high recovery factors. Despite these changes, the salt rejection remained relatively high (99.9%) for both configurations across all tested conditions. The findings revealed that acidification trends caused by MgSO₄ were configuration-dependent, where the parallel setup-controlled rate of pH collapse. This study presented a novel framework connecting membrane module architecture to mass and heat transfer phenomena, providing a transformative DCMD module configuration design in water desalination. These findings not only provide the critical knowledge gaps in DCMD module configurations but also inform optimisation of MD water desalination to achieve high recovery and stable operation conditions under realistic brine composition. Full article

This study examines the effects of natural organic matter (NOM) and dissolved solids on fluoride (F⁻) retention in polyelectrolyte multilayer-based hollow-fiber nanofiltration membranes (dNF40). Lab-scale filtration experiments were conducted under varying operating conditions (initial salt concentration, NOM concentration, permeate flux, crossflow velocity, and recovery rate). dNF40 membranes exhibited F⁻ retention above 70% ± 1.2 in the absence of NOM and competing ions. However, when filtering synthetic model water (SMW) designed to simulate groundwater contaminated with high total dissolved solids (TDSs) and NOM, F⁻ retention decreased to approximately 60% ± 0.7, which was generally attributed to ion competition. Furthermore, despite limited declines in normalized permeability, the addition of NOM to SMW notably deceased F⁻ retention in the steady state to~20% due to fouling effects. The facilitated transport of the divalent cations Ca²⁺ and Mg²⁺ could be observed, as they accumulated in the organic fouling layer. While SO₄²⁻ retention remained relatively stable, the retention of monovalent anions (NO₃⁻, Cl⁻, and F⁻) decreased substantially due to drag effects. Na⁺ retention improved slightly to maintain electroneutrality. Feed salinity was shown to significantly affect separation efficiency, with PEC layers undergoing swelling and certain structural changes as the ionic strength increased. During batch filtration experiments at varying recovery rates, the retention of monovalent anions further decreased, with F⁻ retention reducing to just ~10% at a 90% recovery rate. This study provides valuable insights into better understanding and optimizing the performance of PEC-based NF membranes across diverse water treatment scenarios. Full article

The fields of catalysis and energy storage nowadays quote the use of nanomaterials with well-defined size, morphology, chemical composition, and thermal stability in the high-temperature range and under harsh conditions of reactions. We present herein an approach based on in situ environmental scanning transmission electron microscopy (STEM), combined with analytical STEM and electron tomography (ET), for the evaluation of the thermal stability of hollow Pt nanospheres under vacuum and high-pressure hydrogen environments. Spherical Pt hollow nanospheres (HNSs) with an average diameter of 15 and 34 nm were synthesized by a galvanic replacement-based procedure using either steep or continuous addition of Pt salts during synthesis. The as-synthesized HNSs exhibit complex 3D structures with shells of a few nm constituted by small Pt nanoparticles and marked by the presence of open channels. The thermal stability of Pt-based HNSs under TEM vacuum and 1 bar of hydrogen flow is reported by considering microstructural changes, e.g., the build-up of a continuous shell and its evolution until HNSs collapse at elevated temperatures (>500 °C). Experimental findings are discussed considering fundamental phenomenological issues, i.e., NP faceting, NP diffusion, and subsequent NP sintering, with respect to the behavior of the systems investigated. Full article

We systematically investigated the morphology-controlled synthesis of Cu₂O micro-nano crystals, especially under surfactant-free conditions, targeting a simple, rapid, and morphologically controllable preparation strategy for polyhedral Cu₂O micro-nano crystals. By systematically investigating the effects of NaOH concentration, types of reducing agents, and copper salt precursors on crystal growth, precise control over the morphology of Cu₂O crystals under surfactant-free conditions was achieved. This method can rapidly prepare variously faceted Cu₂O crystals under mild conditions (70 °C, 7 min), including regular polyhedra with low-index facets exposure including cubes, octahedra and rhombic dodecahedra, as well as more complex polyhedra with high-index facets exposure such as 18-faceted, 26-faceted, 50-faceted and 74-faceted crystals. NaOH concentration is found to be the key factor in controlling Cu₂O crystal morphology: as the concentration of NaOH increases, the morphology of Cu₂O crystals gradually transforms from cubes that fully expose the {100} faces to regular polyhedra that expose the {110}, {111} faces, and even other high-index faces, ultimately presenting octahedra that fully expose the {111} faces. Additionally, Cu₂O crystals with unique morphologies such as hollow cubes and 18-faceted with {110} face etched can be obtained by introducing surfactants or prolonging reaction durations. This work provides new insights into the morphology control of Cu₂O crystals and establishes foundation in acquiring distinct Cu₂O polyhedra in a facile manner for their application in catalysis, optoelectronics, sensing, and energy conversion fields. Full article

Treatment of extremely saline water such as the brine rejected from reverse osmosis water desalination plants, and produced water from shale oil and non-conventional gas extraction, is considered a global problem. Consequently, in this work, hollow fiber membrane distillation (HFMD) is experimentally evaluated for desalinating extremely saline water of a salinity ranging from 40,000 to 130,000 ppm. For the purpose of comparison, the HFMD is also tested for desalinating brackish (3000–12,000 ppm) and sea (25,000–40,000 ppm) water. Firstly, the HFMD is tested at two values of feed water temperature (65 and 76 °C) and flow rate (600 and 850 L/h). The experimental results showed that the HFMD productivity significantly increases when the temperature of feed water increases. Increasing the feed water flow rate also has a positive effect on the productivity of HFMD. It is also concluded that the productivity of the HFMD is not significantly affected by increasing the salt concentration when brackish and sea water are used. The productivity also slightly decreases with increasing the salt concentration when extremely saline water is used. The decrement in the productivity reaches 27%, when the salt concentration increases from 40,000 to 130,000 ppm. Based on the conducted economic analysis, the HFMD shows a good potential for desalinating extremely saline water especially when the solar collector is used as a heat source. In this case, the cost per liter of freshwater is reduced by 21.7–23.1% when the evacuated tube solar collectors are used compared to the system using electrical heaters. More reduction in the cost per liter of freshwater is expected when a high capacity solar-powered HFMD plant is installed. Full article

Currently, high-salt diets have become one of the world’s biggest dietary crisis and long-term high-salt diets are seriously detrimental to human health. In response to this situation, the present study proposed a saltiness enhancement strategy using alginate, which is a dietary fibre from brown algae and has many health benefits, such as regulating intestinal microbiota, anti-hypertension and anti-obesity. The comparison of alginates with different viscosities showed that alginate of 1000–1500 cps at a concentration of 1.25 g/L could enhance the saltiness of NaCl solution by 11.5%. Then, a solid salt was prepared through spray drying with 4.83% of this alginate, and its structure was characterised by X-Ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy and energy dispersive spectroscopy to confirm its hollow structure with a particle size of 6.25 ± 2.26 μm as well as its crystal structure similar to original NaCl. Moreover, the conductivity monition revealed that the hollow salt exhibited a more rapid dissolution in water and its alginate component increased the adhesive retention of sodium ions on the tongue surface, which both effectively enhanced the sensory perception. Finally, as revealed by the sensory evaluation, the prepared hollow salt showed higher saltiness than that of original table salt and it could reduce sodium intake by 29%. Thus, the hollow salt prepared with alginate in the present study has potential for salt reduction. Full article

This study explores the layer-by-layer (LBL) modification of polyacrylonitrile (PAN) hollow fibers for effective Mg²⁺/Li⁺ separation. It employs an LBL method of surface modification using polyelectrolytes, specifically aiming to enhance ion selectivity and improve the efficiency of lithium extraction from brines or lithium battery wastes, which is critical for battery recycling and other industrial applications. The modification process involves coating the hydrolyzed PAN fibers with alternating layers of positively charged polyelectrolytes, such as poly(allylamine hydrochloride) (PAH), polyethyleneimine (PEI), or poly(diallyldimethylammonium chloride) (PDADMAC) and negatively charged polyelectrolytes, such as poly(styrene sulfonate) (PSS), to form polyelectrolyte multilayers (PEMs). This study evaluates the modified membranes in Mg²⁺ and Li⁺ salt solutions, demonstrating significant improvements in selectivity for Mg²⁺/Li⁺ separation. PAH was identified as the optimal positively charged polyelectrolyte. PAN hollow fibers modified with ten bilayers of PAH/PSS achieved rejection rates of 95.4% for Mg²⁺ ions and 34.8% for Li⁺ ions, and a permeance of 0.39 LMH/bar. This highlights the potential of LBL techniques for effectively addressing the challenges of ion separation across a variety of applications. Full article

The steady rheological behavior of suspensions of solid particles thickened by cellulose nanocrystals is investigated. Two different types and sizes of particles are used in the preparation of suspensions, namely, TG hollow spheres of 69 µm in Sauter mean diameter and solospheres S-32 of 14 µm in Sauter mean diameter. The nanocrystal concentration varies from 0 to 3.5 wt% and the particle concentration varies from 0 to 57.2 vol%. The influence of salt (NaCl) concentration and pH on the rheology of suspensions is also investigated. The suspensions generally exhibit shear-thinning behavior. The degree of shear-thinning is stronger in suspensions of smaller size particles. The experimental viscosity data are adequately described by a power-law model. The variations in power-law parameters (consistency index and flow behavior index) under different conditions are determined and discussed in detail. Full article

In the pursuit of high energy density batteries beyond lithium, room-temperature (RT) sodium–sulfur (Na-S) batteries are studied, combining sulfur, as a high energy density active cathode material and a sodium anode considered to offer high energy density and very good standard potential. Different liquid electrolyte systems, including three different salts and two different solvents, are investigated in RT Na-S battery cells, on the basis of the solubility of sulfur and sulfides, specific capacity, and cyclability of the cells at different C-rates. Two alternative cathode host materials are explored: A bimodal pore size distribution activated carbon host AC MSC30 and a highly conductive carbon host of hollow particles with porous particle walls. An Na-S cell with a cathode coating with 44 wt% sulfur in the AC MSC30 host and the electrolyte 1M NaFSI in DOL/DME exhibited a specific capacity of 435 mAh/g_S but poor cyclability. An Na-S cell with a cathode coating with 44 wt% sulfur in the host of hollow porous particles and the electrolyte 1M NaTFSI in TEGDME exhibited a specific capacity of 688 mAh/g_S. Full article

The current work introduces the synthesis of inorganic salt nano/micro-crystals during the reduction of hydrogen tetrachloroaurate(III) by Pluronic triblock copolymers (P123, PEO₂₀–PPO₇₀–PEO₂₀). The morphologies and component were confirmed using an electron microscope with an electronic differential system (EDS), and the crystal structures were determined with X-ray diffraction (XRD). The morphologies highly depend on the concentrations of Pluronic and pH values. The mean size of the nanocrystal and hollow micro-crystal were controlled typically in the range of 32–150 nm (side length) and 1.4 μm, respectively. Different from the electrospray–ionization (EI) method, a model in which KCl forms a supersaturated solution in the micellar core of Pluronic is used to explain the formation process. This work provides the new insight that inorganic salt nanocrystals could be synthesized with the template of micelles in pure aqueous solutions. Full article

We describe the creation of a conductive microcavity based on the assembly of two pieces of carbon nanotube buckypaper for the entrapment of two enzymes, horseradish peroxidase (HRP) and glucose oxidase (GOx), as well as a redox mediator: 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid diammonium salt (ABTS). The hollow electrode, employing GOx, HRP, and the mediator, as an electrochemical enzyme cascade model, is utilized for glucose sensing at a potential of 50 mV vs. Ag/AgCl. This bienzyme electrode demonstrates the ability to oxidize glucose by GOx and subsequently convert H₂O₂ to water via the electrical wiring of HRP by ABTS. Different redox mediators (ABTS, potassium hexacyanoferrate (III), and hydroquinone) are tested for HRP wiring, with ABTS being the best candidate for the electroenzymatic reduction of H₂O₂. To demonstrate the possibility to optimize the enzyme cascade configuration, the enzyme ratio is studied with 1 mg HRP combined with variable amounts of GOx (1–4 mg) and 2 mg GOx combined with variable amounts of HRP (0.5–2 mg). The bienzyme electrode shows continuous operational stability for over a week and an excellent storage stability in phosphate buffer, with a decay of catalytic current by only 29% for 1 mM glucose after 100 days. Full article

Pollen grains, with their resilient sporopollenin exine and defined morphologies, have been explored as bio-templates for the synthesis of calcium phosphate minerals, particularly hydroxyapatite (HAp) and β-tricalcium phosphate (TCP). Various pollen morphologies from different plant species (black alder, dandelion, lamb’s quarters, ragweed, and stargazer lily) were evaluated. Pollen grains underwent acid washing to remove allergenic material and facilitate subsequent calcification. Ragweed and lamb’s quarter pollen grains were chosen as templates for calcium phosphate salts deposition due to their distinct morphologies. The calcification process yielded well-defined spherical hollow particles. The washing step, intended to reduce the protein content, did not significantly affect the final product; thus, justifying the removal of this low-yield step from the synthesis process. Characterisation techniques, including X-ray diffraction, scanning electron microscopy, Fourier-transform infrared spectroscopy, and thermal gravimetric analysis, confirmed the successful calcification of pollen-derived materials, revealing that calcified grains were principally composed of calcium deficient HAp. After calcination, biphasic calcium phosphate composed of HAp and TPC was obtained. This study demonstrated the feasibility of using pollen grains as green and sustainable bio-templates for synthesizing biomaterials with controlled morphology, showcasing their potential in biomedical applications such as drug delivery and bone regeneration. Full article

In recent years, there has been a growing interest in developing smart drug delivery systems based on natural resources combined with stimulus-sensitive elements. This trend aims to formulate innovative and sustainable delivery platforms tailored for topical applications. This work proposed the use of layer-by-layer (LbL) methodology to fabricate biocompatible photo-responsive multilayer systems. These systems are composed of a polyoxometalate inorganic salt (POM) ([NaP₅W₃₀O₁₁₀]¹⁴⁻) and a natural origin polymer, chitosan (CHT). Curcumin (CUR), a natural bioactive compound, was incorporated to enhance the functionality of these systems during the formation of hollow capsules. The capsules produced, with sizes between 2–5µm (SEM), were further dispersed into CHT/VCO (virgin coconut oil) emulsion solutions that were casted into molds and dried at 37 °C for 48 h. The system presented a higher water uptake in PBS than in acidic conditions, still significantly lower than that earlier reported to other CHT/VCO-based systems. The drug release profile is not significantly influenced by the medium pH reaching a maximum of 37% ± 1% after 48 h. The antioxidant performance of the designed structures was further studied, suggesting a synergistic beneficial effect resulting from CUR, POM, and VCO individual bioactivities. The increased amount of those excipients released to the media over time promoted an increase in the antioxidant activity of the system, reaching a maximum of 38.1% ± 0.1% after 48 h. This work represents a promising step towards developing advanced, sustainable drug delivery systems for topical applications. Full article

This paper presents an original and sustainable method for producing ZnO nanoparticles (NPs) in response to global challenges (low energy requirements, low environmental impact, short production times, and high production yield). The method is based on an ion exchange process between an anionic resin and an aqueous ZnCl₂ solution; it operates in one step at room temperature/ambient pressure without the need for complex apparatus or purification steps. From the kinetics, we observed the formation of pure simonkolleite, a zinc-layered hydroxide salt (Zn₅(OH)₈Cl₂·H₂O), after only 5 min of reaction. This compound, used elsewhere as a ZnO precursor after calcination at high temperatures, here decomposes at room temperature into ZnO, allowing extraordinary savings of time and energy. Finally, in only 90 min, pure and crystalline ZnO NPs are obtained, with a production yield > 99%. Several types of aggregates resulting from the self-assembly of small hexagonal platelets (solid or hollow in shape) were observed. Using our revolutionary method, we produced almost 10 kg of ZnO NPs per week without any toxic waste, significantly reducing energy consumption; this method allows transferring the use of these unique NPs from the laboratory environment to the real world. Full article

Reverse osmosis (RO) membrane materials play a key role in determining energy consumption. Currently, CTA is regarded as having one of the highest degrees of chlorine resistance among materials in the RO process. The hollow fiber membrane has the advantages of a large membrane surface area and a preparation process without any redundant processes. Herein, response surface methodology with Box–Behnken Design (BBD) was applied for optimizing the preparation conditions of the cellulose triacetate (CTA) hollow fiber RO membrane. There were four preparation parameters, including solid content, spinning temperature, post-treatment temperature, and post-treatment time, which could affect the permeability of the membrane significantly. In this study, the interaction between preparation parameters and permeability (permeate flux and salt rejection) was evaluated by regression equations. Regression equations can be applied to obtain the optimized preparation parameters of hollow fiber RO membranes and reasonably predict and optimize the permeability of the RO membranes. Finally, the optimized preparation conditions were solid content (44%), spinning temperature (167 °C), post-treatment temperature (79 °C), and post-treatment time (23 min), leading to a permeability of 12.029 (L·m⁻²·h⁻¹) and salt rejection of 90.132%. This study of reinforced that CTA hollow fiber membrane may promote the transformation of the RO membrane industry. Full article