Search Results (55)

Based on Digital Beamforming (DBF) technology, spaceborne SAR systems can achieve high-resolution and wide-swath (HRWS) imaging. When combined with reflector antennas, the DBF-SCORE (Digital Beamforming-SCan On REceive) system also features light weight and low cost, making it an important choice for spaceborne HRWS SAR. This paper firstly proposes an advanced Full-chain Real-time Internal Calibration (FRIC) scheme, where the calibration path covers the entire receive chain from the antenna feed port to the input port of the Analog-to-Digital Converter (ADC) and achieves high-precision internal calibration concurrently with data acquisition. Secondly, based on the L-band reflector antenna DBF-SCORE system architecture, the design of radio frequency (RF) front end, namely the Transmit-Receive-Calibration Module (TRCM), is carried out. We propose the implementation of azimuth encoding modulation of the calibration signal through periodic switch control within the TRCM. Subsequently, the calibration signal is extracted using waveform diversity technology and its Signal-to-Noise Ratio (SNR) is improved through azimuth coherent integration technology. In addition, a ground verification system is established using the TRCM to evaluate the comprehensive performance of transmitting, receiving, and real-time internal calibration. Experimental results verify the effectiveness of the FRIC scheme and provide valuable insights for future spaceborne DBF SAR systems. Full article

Sparse Synthetic Aperture Radar (SAR) imaging has garnered significant attention due to its ability to suppress azimuth ambiguity in under-sampled conditions, making it particularly useful for high-resolution wide-swath (HRWS) SAR systems. Traditional compressed sensing-based sparse SAR imaging algorithms are hindered by range–azimuth coupling induced by range cell migration (RCM), which results in high computational cost and limits their applicability to large-scale imaging scenarios. To address this challenge, the approximated observation-based sparse SAR imaging algorithm was developed, which decouples the range and azimuth directions, significantly reducing computational and temporal complexities to match the performance of conventional matched filtering algorithms. However, this method requires iterative processing and manual adjustment of parameters. In this paper, we propose a novel deep neural network-based sparse SAR imaging method, namely the Self-supervised Azimuth Ambiguity Suppression Network (SAAS-Net). Unlike traditional iterative algorithms, SAAS-Net directly learns the parameters from data, eliminating the need for manual tuning. This approach not only improves imaging quality but also accelerates the imaging process. Additionally, SAAS-Net retains the core advantage of sparse SAR imaging—azimuth ambiguity suppression in under-sampling conditions. The method introduces self-supervision to achieve orientation ambiguity suppression without altering the hardware architecture. Simulations and real data experiments using Gaofen-3 validate the effectiveness and superiority of the proposed approach. Full article

Traditional single-channel Synthetic Aperture Radar (SAR) cannot achieve high-resolution and wide-swath (HRWS) imaging due to the constraint of the minimum antenna area. Distributed HRWS SAR can realize HRWS imaging and also possesses the resolution ability in the height dimension by arranging multiple satellites in the elevation direction. Nevertheless, due to the excessively high pulse repetition frequency (PRF) of the distributed SAR system, range ambiguity will occur in large detection scenarios. When directly performing 3D-imaging processing on SAR images with range ambiguity, both focused point clouds and blurred point clouds will exist simultaneously in the generated 3D point clouds, which affects the quality of the generated 3D-imaging point clouds. To address this problem, this paper proposes a 3D blur suppression method for HRWS blurred images, which estimates and eliminates defocused point clouds based on focused targets. The echoes with range ambiguity are focused in the near area and the far area, respectively. Then, through image registration, amplitude and phase correction, and height-direction focusing, the point clouds in the near area and the far area are obtained. The strongest points in the two sets of point clouds are iteratively selected to estimate and eliminate the defocused point clouds in the other set of point clouds until all the ambiguity is eliminated. Simulation experiments based on airborne measured data verified the capability to achieve HRWS 3D blur suppression of this method. Full article

Azimuth multi-channel techniques show great promise in high-resolution, wide-swath synthetic aperture radar systems. However, in practical engineering applications, errors between channels can significantly affect the reconstruction of multi-channel echo data, leading to a degraded synthetic aperture radar image. To address this issue, this article derives the formula expression in the two-dimensional time domain after single-channel processing under the assumption of an insufficient azimuth sampling rate and proposes a novel algorithm based on the statistical treatment of characteristic clusters. In this algorithm, channel imaging is first performed separately; then, the image is divided into a predefined number of sub-images. The characteristic clusters and points within each sub-image are identified, and their positions, amplitude, and phase information are used to obtain the range synchronization errors, amplitude errors, and phase errors between channels. Compared with traditional methods, the proposed method does not require iteration or the complex eigenvalue decomposition of the covariance matrix. Furthermore, it can utilize existing imaging tools and software in single-channel synthetic aperture radar systems. The effectiveness of the proposed method is validated through simulation experiments and real-world data processing. Full article

Multiple-input multiple-output (MIMO) synthetic aperture radar (SAR) is a promising scheme for high-resolution wide-swath (HRWS) imaging. After echo separation processing, a MIMO-SAR system can provide many equivalent phase centers (EPCs) in azimuth. However, EPC duplication occurs for traditional monostatic systems with uniform antenna arrays, leading to system resource waste. Moreover, range ambiguity suppression is a necessary process for wide-swath SAR systems. In this paper, a novel MIMO-SAR echo separation and range ambiguity suppression processing framework is proposed for HRWS imaging. A set of transmission delays is introduced to the transmit channels to displace the repetitive EPCs. The transmission delays can also be used to flexibly control the performance of echo separation. A wide-null beamformer is employed to accomplish echo separation and ambiguity suppression simultaneously. The proposed framework is designed for real-time processing and therefore does not require frequency-domain operations. Finally, the proposed framework is verified through point target and distributed scene simulation experiments. Full article

The multichannel synthetic aperture radar (SAR) possesses the capability to acquire high-resolution, wide-swath SAR imagery, which has great potential for application. However, similar to traditional single-channel SAR systems, it suffers from imaging quality degradation due to motion errors. Many motion compensation algorithms have been used to improve the quality of single-channel SAR images, while fewer studies have been conducted on multichannel SAR motion compensation methods. The sub-image motion compensation method utilizes the single channel motion errors to perform multichannel motion errors compensation, considering that multiple channels have the same phase errors. To improve the quality of multichannel SAR imaging when multiple channel motion errors are inconsistent, this paper proposes a motion compensation method with multichannel phase correction for HRWS SAR. First, the method derives the phase errors estimation model via maximum sharpness to simultaneously estimate multichannel phase. Then, it compensates for the motion errors of all channels during backprojection imaging. The inconsistent motion errors of multiple channels can be compensated by estimating the phase errors of all channels, improving the image quality. The channel phase errors can be corrected while compensating for the motion errors. Moreover, the experimental results of point targets and complex scenes validate the effectiveness of the proposed method. Full article

Azimuth resolution and swath width are two crucial parameters in spaceborne synthetic aperture radar (SAR) systems. However, it is difficult for conventional spaceborne SAR to simultaneously achieve high-resolution wide-swath (HRWS) due to the minimum antenna area constraint. To mitigate this limitation, some representative HRWS SAR imaging techniques have been investigated, e.g., the azimuth multichannel technique, digital beamforming (DBF) technique, and pulse repetition interval (PRI) variation technique. This paper focus on a comprehensive review of the three techniques with respect to their latest developments. First, some key parameters of HRWS SAR are presented and analyzed to help the reader establish the general concept of SAR. Second, three techniques are introduced in detail, roughly following a simple-to-complex approach, i.e., start with the basic concept, then move to the core principles and classic technical details, and finally report the technical challenges and corresponding solutions. Third, some in-depth insights on the comparison among the three techniques are given. The purpose of this paper is to provide a review and brief perspective on the development of HRWS SAR. Full article

Multichannel Synthetic Aperture Radar (MC-SAR) systems, such as Azimuth Multi-Phase Centre (AMPC) SAR, provide an effective solution for achieving high-resolution wide-swath (HRWS) imaging by reducing the pulse repetition frequency (PRF) to increase the swath width. However, in an Electronic Countermeasures (ECM) environment, the image quality of multichannel SAR systems can be significantly degraded by electromagnetic interference. Previous research into interference and counter-interference techniques has predominantly focused on single-channel SAR systems, with relatively few studies addressing the specific challenges faced by MC-SAR systems. This paper uses the classical spatial filtering technique of adaptive digital beamforming (DBF). Considering the Doppler ambiguity present in the echoes, two schemes—Interference Reconstruction And Cancellation (IRC) and Channel Grouping Nulling (CGN)—are designed to effectively eliminate suppressive interference. The IRC method eliminates the effects of interference without losing spatial degrees of freedom, ensuring effective suppression of Doppler ambiguity in subsequent processing. This method shows significant advantages under conditions of strong Doppler ambiguity and low jammer-to-signal ratio. Conversely, the CGN method mitigates the effect of interference on multichannel imaging at the expense of degrees of freedom redundant to Doppler ambiguity suppression. It shows remarkable interference suppression performance under weak-Doppler-ambiguity conditions, allowing for better image recovery. Simulations performed on point and distributed targets have validated that the proposed methods can effectively remove interfering signals and achieve high-resolution wide-swath (HRWS) SAR images. Full article

Azimuth multi-channel synthetic aperture radar (SAR) has always been an important technical means to achieve high-resolution wide-swath (HRWS) SAR imaging. However, in the space-borne azimuth multi-channel SAR system, random phase noise will be produced during the operation of each channel receiver. The phase noise of each channel is superimposed on the SAR echo signal of the corresponding channel, which will cause the phase imbalance between the channels and lead to the generation of false targets. In view of the above problems, this paper proposes a random phase noise compensation method for space-borne azimuth multi-channel SAR. This method performs feature decomposition by calculating the covariance matrix of the echo signal and converts the random phase noise estimation into the optimal solution of the cost function. Considering that the phase noise in the receiver has frequency-dependent and time-varying characteristics, this method calculates the phase noise estimation value corresponding to each range-frequency point in the range direction and obtains the phase noise estimation value by expectation in the azimuth direction. The proposed random phase noise compensation method can suppress false targets well and make the radar present a well-focused SAR image. Finally, the usefulness of the suggested method is verified by simulation experiments. Full article

The spaceborne high-resolution and wide-swath synthetic aperture radar (HRWS-SAR) system combined with the ground moving target indication (GMTI) mode provides a promising prospect in the realization of wide-area target surveying and high-resolution target imaging. In this paper, a system design method is proposed for an HRWS-SAR-GMTI system with ideal reconstruction configuration. In the proposed method, the whole azimuth receiving channels are uniformly divided into multiple groups, where HRWS-SAR imaging is implemented in each sub-group and then GMTI processing is performed based on the reconstructed SAR images. Then, an optimal candidate PRF is properly selected with respect to the optimal reconstruction configuration. After that, the digital beam forming scanning on receive (DBF-SCORE) technique is applied to further enlarge the range swath and improve the noise equivalent scattering coefficient (NESZ). Based on the predesigned system, HRWS-SAR image-based GMTI processing can finally be accomplished. The effectiveness of the proposed method is validated by simulated experiments. Full article

High-resolution and wide-swath (HRWS) synthetic aperture radar (SAR) imaging with azimuth multi-channel always suffers from channel phase and amplitude errors. Compared with spatial-invariant error, the range-dependent channel phase error is intractable due to its spatial dependency characteristic. This paper proposes a novel parameterized channel equalization approach to reconstruct the unambiguous SAR imagery. First, a linear model is established for the range-dependent channel phase error, and the sharpness of the reconstructed Doppler spectrum is used to measure the unambiguity quality. Furthermore, the intrinsic relationship between the channel phase errors and the sharpness is revealed, which allows us to estimate the optimal parameters by maximizing the sharpness of the reconstructed Doppler spectrum. Finally, the results from real-measured data show that the suggested method performs exceptionally for ambiguity suppression in HRWS SAR imaging. Full article

Single-phase center multiple azimuth beam (SPC MAB) mode is an effective method for high-resolution wide-swath (HRWS) SAR imaging. The traditional azimuth spectrum reconstruction method for SPC MAB mode is based on the combination scheme from which fake targets along the azimuth direction arise because the inter-beam interference is not considered. When the real antenna mode is inconsistent with the ideal one, the disadvantages of the combination scheme become more serious. In this paper, based on the basic theory of the low-pass, band-limited, multiple-channel under-sampling and reconstruction, a novel digital beam-forming method is proposed for the SPC MAB imaging mode with ideal antenna mode first. The method analyzes the system functions of the sub-beams, based on which digital beam-forming filters are designed for all the sub-beams. The designed filters can reconstruct the correct wide-bandwidth azimuth spectrum and suppress the inter-beam interference simultaneously. Furthermore, the proposed method is extended to SPC MAB mode with the non-ideal antenna mode. The simulation experiments prove the validities of the proposed method both for azimuth spectral reconstruction and the inter-beams interfering suppressing, no matter that the SPC MAB’s antenna mode is ideal or non-ideal. Full article

Imaging maritime targets requires a high resolution and wide swath (HWRS) in a synthetic aperture radar (SAR). When operated with a variable pulse repetition interval (PRI), a staggered SAR can realize HRWS imaging, which needs to be reconstructed due to echo pulse loss and a nonuniformly sampled signal along the azimuth. The existing reconstruction algorithms are designed for stationary scenes in a staggered SAR mode, and thus, produce evident image defocusing caused by complex target motion for moving targets. Typically, the nonuniform sampling and complex motion of maritime targets aggravate the spectrum aliasing in a staggered SAR mode, causing inevitable ambiguity and degradation in its reconstruction performance. To this end, this study analyzed the spectrum of maritime targets in a staggered SAR system through theoretical derivation. After this, a reconstruction method named MBLCFD (Modified Best Linear Unbaised and Complex-Lag Time-Frequency Distribution) is proposed to refocus the blurred maritime target. First, the signal model of the maritime target with 3D rotation accompanying roll–pitch–yaw movement was established under the curved orbit of the satellite. The best linear unbiased (BLU) method was modified to alleviate the coupling of nonuniform sampling and target motion. A precise SAR algorithm was performed based on the method of inverse reversion to counteract the effect of a curved orbit and wide swath. Based on the hybrid SAR/ISAR technique, the complex-lag time-frequency distribution was exploited to refocus the maritime target images. Simulations and experiments were carried out to verify the effectiveness of the proposed method, providing precise refocusing performance in staggered mode. Full article

High-resolution wide-swath (HRWS) imaging is the research focus of the modern spaceborne synthetic-aperture radar (SAR) imaging field, with significant relevance and vast application potential. Staggered SAR, as an innovative imaging system, mitigates blind areas across the entire swath by periodically altering the radar pulse repetition interval (PRI), thereby extending the swath width to multiples of that achievable by conventional systems. However, the staggered mode introduces inherent challenges, such as nonuniform azimuth sampling and echo data loss, leading to azimuth ambiguities and substantially impacting image quality. This paper proposes a sparse SAR imaging method for the low-oversampled staggered mode via compound regularization. The proposed method not only effectively suppresses azimuth ambiguities arising from nonuniform sampling without necessitating the restoration of missing echo data, but also incorporates total variation (TV) regularization into the sparse reconstruction model. This enhances the accurate reconstruction of distributed targets within the scene. The efficacy of the proposed method is substantiated through simulations and real data experiments from spaceborne missions. Full article

The displaced phase center multiple azimuth beams (DPCMAB) technique can help spaceborne synthetic aperture radar (SAR) systems obtain the high-resolution wide-swath (HRWS) imaging capacity, and azimuth multichannel reconstruction is usually required due to azimuth non-uniform sampling. Compared with stationary and moving targets, the range history and azimuth signal model of the moving target with an acceleration are obviously different. The azimuth multichannel signal model of an accelerated moving target is established, and the relationship between acceleration and Doppler parameters is analyzed. Furthermore, the impact of the acceleration on azimuth multichannel reconstruction and imaging results is simulated and analyzed. According to the azimuth multichannel signal model, an azimuth multichannel reconstruction approach for accelerated moving targets is proposed. The key point of the proposed reconstruction approach is the modified azimuth multichannel matrix, which is related not only to azimuth and slant velocities but also accelerations. The target’s velocities and accelerations are obtained using multiple Doppler parameter estimations. Compared with the conventional method of processing the raw data of accelerated moving targets, this proposed method could distinctly suppress image defocusing and pairs of false targets. Simulation results on point targets validate the proposed azimuth multichannel reconstruction approach. Full article