Search Results (543)

Pseudo-persistent organic pollutants, such as pharmaceuticals, personal care products (PPCPs), and organic dyes, are a major issue in current environmental engineering. Considering the limitations of traditional wastewater treatment plant methods and degradation technologies for organic pollutants, the search for new technologies more suitable for treating these new types of pollutants has become a research hotspot in recent years. Membrane filtration, adsorption, advanced oxidation, and electrochemical advanced oxidation technologies can effectively treat new organic pollutants. The electro-advanced oxidation process based on sulfate radicals is renowned for its non-selectivity, high efficiency, and environmental friendliness, and it can improve the dewatering performance of sludge after wastewater treatment. Therefore, in this study, octyl methoxycinnamate (OMC) was selected as the target pollutant. A new type of electrochemical filtration device based on the advanced oxidation process of sulfate radicals was designed, and a new type of modified carbon nanotube material electrode was synthesized to enhance its degradation effect. In a mixed system of water and acetonitrile, the efficiency of the electrochemical filtration device loaded with the modified electrode for degrading OMC is 1.54 times that at room temperature. The experimental results confirmed the superiority and application prospects of the self-designed treatment scheme for organic pollutants, providing experience and a reference for the future treatment of PPCP pollution. Full article

The discharge of oily wastewater threatens the ecosystem and human health, and the efficient treatment of oily wastewater is confronted with problems of high mass transfer resistance at the oil-water-solid multiphase interface, significant light shielding effect, and easy deactivation of photocatalysts. Although traditional physical separation methods avoid secondary pollution by chemicals and can effectively separate floating oil and dispersed oil, they are ineffective in removing emulsified oil with small particle sizes. To address these complex challenges, photocatalytic technology and photocatalysis-based improved technologies have emerged, offering significant application prospects in degrading organic pollutants in oily wastewater as an environmentally friendly oxidation technology. In this paper, the degradation mechanism, kinetic mechanism, and limitations of conventional photocatalysis technology are briefly discussed. Subsequently, the surface interface modulation functions of metal doping and heterojunction energy band engineering, along with their applications in enhancing the light absorption range and carrier separation efficiency, are reviewed. Focus on typical studies on the separation and degradation of aqueous and oily phases using photocatalytic membrane technology, and illustrate the advantages and mechanisms of photocatalysts loaded on the membranes. Finally, other new approaches and converging technologies in the field are outlined, and the challenges and prospects for the future treatment of oily wastewater are presented. Full article

Winery wastewater (WWW), if released untreated, poses a serious environmental threat due to its high organic load. In this study, Chlorella vulgaris was cultivated in diluted WWW to assess its suitability as a culture medium. Two outdoor cultivation systems—a 270 L raceway and a 40 L bubble column—were operated over 33 days using synthetic medium (control) and WWW. A flow cytometry (FC) protocol was implemented to monitor key physiological parameters in near-real time, including cell concentration, membrane integrity, chlorophyll content, cell size, and internal complexity. At the end of cultivation, the bubble column yielded the highest cell concentrations: 2.85 × 10⁶ cells/mL (control) and 2.30 × 10⁶ cells/mL (WWW), though with lower proportions of intact cells (25% and 31%, respectively). Raceway cultures showed lower cell concentrations: 1.64 × 10⁶ (control) and 1.54 × 10⁶ cells/mL (WWW), but higher membrane integrity (76% and 36% for control and WWW cultures, respectively). On average, cells grown in the bubble column had a 22% larger radius than those in the raceway, favouring sedimentation. Heterotrophic cells were more abundant in WWW cultures, due to the presence of organic carbon, indicating its potential for use as animal feed. This study demonstrates that FC is a powerful, real-time tool for monitoring microalgae physiology and optimising cultivation in complex effluents like WWW. Full article

Ag-doped ZnO is a promising photocatalyst. However, the combined influence of the Ag doping concentration and furnace temperature has not been adequately explored, hindering the optimization of ZnO/Ag materials for practical applications. In this study, ZnO/Ag materials were synthesized via ultrasonic spray pyrolysis by systematically varying both the furnace calcination temperature and the Ag doping concentration. The synthesized materials were analyzed through a range of spectroscopic methods to investigate their structural, morphological, and surface characteristics. Their photocatalytic activity was assessed by monitoring the degradation of methylene blue (MB) under ultraviolet light exposure. The findings indicate that the ZnO sample that was calcined at 400 °C exhibited the highest degradation efficiency among the undoped samples, which can be attributed to its submicron particle size, moderate crystallinity, and high surface hydroxylation. The sample with 5-wt% Ag doping achieved enhanced performance, demonstrating the best photocatalytic activity (65% MB degradation). This improvement was attributed to the synergistic effects of surface plasmon resonance and optimized interaction between the Ag nanoparticles and surface hydroxyl groups. Excessive Ag loading (10 wt%) led to reduced activity owing to potential agglomeration and recombination centers. These results highlight the critical role of both the thermal and chemical parameters in tailoring ZnO-based photocatalysts for wastewater treatment applications. Full article

The seismicity levels in Oklahoma and southern Kansas have increased dramatically over the last 15 years. Past studies have identified the massive disposal of wastewater co-produced during oil and gas extraction as the driving force behind some earthquake clusters, with a small number of events directly linked to hydraulic fracturing (HF) stimulations. The present investigation is the first one to examine the role both of these activities played throughout the two states, under the same framework. Our findings confirm that wastewater disposal is the main causal factor, while also identifying several previously undocumented clusters of seismicity that were triggered by HF. We were able to identify areas where both causal factors spatially coincide, even though they act at distinct depth intervals. Overall, oil and gas operations are probabilistically linked at high confidence levels with more than 7000 felt earthquakes (M ≥ 2.5), including 46 events with M ≥ 4.0 and 4 events with M ≥ 5. Our analysis utilized newly compiled regional earthquake catalogs and established physics-based principles. It first hindcasts the seismicity rates after 2012 on a spatial grid using either real or randomized HF and wastewater data as the input, and then compares them against the null hypothesis of purely tectonic loading. In the end, each block is assigned a p-value, reflecting the statistical confidence in its causal association with either HF stimulations or wastewater disposal. Full article

In this work, a glassy carbon electrode (GCE) modified with reduced graphene oxide and β-cyclodextrin (rGO/β-CD) nanocomposite was developed for the electrochemical detection of nitrofurantoin (NFT). The structural and morphological characteristics of the synthesized nanocomposite were determined using scanning electron microscopy (SEM), Raman spectroscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Moreover, the electrochemical behavior of the modified electrodes was thoroughly examined using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), with the rGO/β-CD-modified glassy carbon electrode (GCE) demonstrating superior electron transfer capability. Key experimental parameters, including scan rate, material loading, and solution pH, were systematically optimized. After optimizing the experimental conditions, the modified sensor showed excellent electrocatalytic performance and selectivity toward NFT, achieving a broad linear detection range from 0.5 to 120 μM, a low limit of detection (LOD) of 0.048 μM, and a high sensitivity of 12.1 µA µM^–1 cm^–2 using differential pulse voltammetry (DPV). Furthermore, the fabricated electrode exhibited good anti-interference ability, stability, precision, and real-time applicability for NFT detection in a wastewater sample. These results highlight the potential of the rGO/β-CD nanocomposite as a high-performance platform for electrochemical sensing applications. Full article

The disposal of wastewater resulting from petroleum industries presents a major environmental challenge due to the presence of hard-to-degrade organic pollutants, such as oils and hydrocarbons, and high chemical oxygen demand (COD). In this study, an efficient and eco-friendly method was developed to treat such wastewater using a photocatalyst composed of biochar derived from pistachio shells and loaded with zinc oxide (ZnO) nanoparticles. The biochar-ZnO composite was prepared via a co-precipitation-assisted pyrolysis method to evaluate its efficiency in the photocatalytic degradation of petroleum wastewater (PW). The synthesized material was characterized using various techniques, including scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR) spectroscopy, to determine surface morphology, crystal structure, and functional groups present on the catalyst surface. Photocatalytic degradation experiments were conducted under UV and sunlight for 90 h of irradiation to evaluate the performance of the proposed system in removing oil and reducing COD levels. Key operational parameters, such as pH (2–10), catalyst dosage (0–0.1) g/50 mL, and oil and COD concentrations (50–500) ppm and (125–1252) ppm, were optimized by response surface methodology (RSM) to obtain the maximum oil and COD removal efficiency. The oil and COD were removed from PW (90.20% and 88.80%) at 0.1 g/50 mL of PS/ZnO, a pH of 2, and 50 ppm oil concentration (125 ppm of COD concentration) under UV light. The results show that pollutant removal is slightly better when using sunlight (80.00% oil removal, 78.28% COD removal) than when using four lamps of UV light (77.50% oil removal, 75.52% COD removal) at 0.055 g/50 mL of PS/ZnO, a pH of 6.8, and 100 ppm of oil concentration (290 ppm of COD concentration). The degradation rates of the PS/ZnO supported a pseudo-first-order kinetic model with R² values of 0.9960 and 0.9922 for oil and COD. This work indicates the potential use of agricultural waste, such as pistachio shells, as a sustainable source for producing effective catalysts for industrial wastewater treatment, opening broad prospects in the field of green and nanotechnology-based environmental solutions in the development of eco-friendly and effective wastewater treatment technologies under solar light. Full article

Microbial fuel cells (MFCs) generate electricity through the microbial oxidation of organic waste. However, the inherent electrochemical performance of carbon felt (CF) electrodes is relatively poor and requires enhancement. In this study, nickel oxide (NiO) was successfully loaded onto CF to improve its electrode performance, thereby enhancing the electricity generation capacity of MFCs during the degradation of treated wastewater. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy diffusion spectrometer (EDS) analyses confirmed the successful deposition of NiO on the CF surface. The modification enhanced both the conductivity and capacitance of the electrode and increased the number of microbial attachment sites on the carbon fiber filaments. The prepared CF–NiO electrode was employed as the anode in an MFC, and its electrochemical and energy storage performance were evaluated. The maximum power density of the MFC with the CF–NiO anode reached 0.22 W/m², compared to 0.08 W/m² for the unmodified CF anode. Under the C1000-D1000 condition, the charge storage capacity and total charge output of the CF–NiO anode were 1290.03 C/m² and 14,150.03 C/m², respectively, which are significantly higher than the 452.9 C/m² and 6742.67 C/m² observed for the CF anode. These results indicate notable improvements in both power generation and energy storage performance. High-throughput gene sequencing of the anodic biofilm following MFC acclimation revealed that the CF–NiO anode surface hosted a higher proportion of electroactive bacteria. This suggests that the NiO modification enhances the biodegradation of organic matter and improves electricity generation efficiency. Full article

The rapid expansion of shrimp aquaculture has led to the generation of nutrient-rich effluents, which contribute to environmental degradation if inadequately managed. This study evaluated the potential of Dunaliella salina for the reuse of shrimp aquaculture wastewater (SAW) in biofloc production systems under varying dilution levels (0%, 25%, and 50%) and the simultaneous production of high-value biomass. Growth kinetics were modeled using a four-parameter logistic model, and nutrient removal, biochemical composition, and fatty acid profile were assessed. D. salina exhibited substantial growth in undiluted SAW, achieving over 80% removal of total nitrogen and reducing the organic load, as measured by a chemical oxygen demand reduction of more than 79%. In SAW treatments, the protein content ranged from 24.7% to 26.3%, while the lipid content reached up to 67.1% in a 25% SAW dilution. Chlorophyll a and total carotenoids were measured at 5.3–7 µg/mL and 4.1–5.7 µg/mL, respectively, in SAW treatments. The polyunsaturated fatty acid content in undiluted SAW was 34.5%, with α-linolenic acid (C18:3n3) and linoleic acid (C18:2n6) comprising 12% and 7.5%, respectively. This study demonstrates the ability of D. salina to valorize shrimp aquaculture wastewater in biofloc systems into lipid-rich, bioactive biomass, supporting its use in integrated aquaculture biotechnology systems for sustainable wastewater management and bioproduct generation. Full article

The recirculating aquaculture system (RAS) has been rapidly adopted worldwide in recent years due to its high productivity, good stability, and good environmental controllability (and therefore friendliness to environment and ecology). Nevertheless, the effluent from seawater RAS contains a high level of ammonia nitrogen which is toxic to fish, so it is necessary to overcome the salinity conditions to achieve rapid and efficient nitrification for recycling. The moving bed biofilm reactor (MBBR) has been widely applied often by using PE fillers for efficient wastewater treatment. However, the start-up of MBBR in seawater environments has remained a challenge due to salinity stress and harsh inoculation conditions. This study investigated a new PE-filler surface modification method towards the enhanced start-up of mariculture MBBR by combining liquid-phase oxidation and maifanstone powder. The aim was to obtain a higher porous surface and roughness and a strong adsorption and alkalinity adjustment for the MBBR PE filler. The hydrophilic properties, surface morphology, and chemical structure of a raw polyethylene filler (an unmodified PE filler), liquid-phase oxidation modified filler (LO-PE), and liquid-phase oxidation combined with a coating of a maifanstone-powder-surface-modified filler (LO-SCPE) were first investigated and compared. The results showed that the contact angle was reduced to 45.5° after the optimal liquid-phase oxidation modification for LO-PE, 49.8% lower than that before modification, while SEM showed increased roughness and surface area by modification. Moreover, EDS presented the relative content of carbon (22.75%) and oxygen (42.36%) on the LO-SCPE surface with an O/C ratio of 186.10%, which is 177.7% higher than that of the unmodified filler. The start-up experiment on MBBRs treating simulated marine RAS wastewater (HRT = 24 h) showed that the start-up period was shortened by 10 days for LO-SCPE compared to the PE reactor, with better ammonia nitrogen removal observed for LO-SCPE (95.8%) than the PE reactor (91.7%). Meanwhile, the bacterial community composition showed that the LO-SCPE reactor had a more diverse and abundant AOB and NOB. The Nitrospira has a more significant impact on nitrification because it would directly oxidize NH₄⁺-N to NO₃⁻-N (comammox pathway) as mediated by AOB and NOB. Further, the LO-SCPE reactor showed a higher NH₄⁺-N removal rate (>99%), less NO₂⁻-N accumulation, and a shorter adaption period than the PE reactor. Eventually, the NH₄⁺-N concentrations of the three reactors (R1, R2, and R3) reached <0.1 mg/L within 3 days, and their NH₄⁺-N removal efficiencies achieved 99.53%, 99.61%, and 99.69%, respectively, under ammonia shock load. Hence, the LO-SCPE media have a higher marine wastewater treatment efficiency. Full article

Hypoxia in river estuaries poses significant ecological and water safety risks, yet long-term high-frequency monitoring data for comprehensive analysis remain scarce. This study investigates hypoxia dynamics in the Shenzhen River Estuary (southern China) using two-year high-frequency monitoring data. A hybrid anomaly detection method integrating wavelet analysis and temporal information entropy was developed to identify hypoxia events. The drivers of hypoxia were also identified with correlation coefficients and transfer entropy (TE). The results reveal frequent spring–summer hypoxia. Turbidity and total nitrogen (TN) exhibited significant negative correlations and time-lagged effects on dissolved oxygen (DO), where TE reaches a peak of 0.05 with lags of 36 and 72 h, respectively. Wastewater treatment plant (WWTP) loads, particularly suspended solids (SSs), showed a linear negative correlation with estuarine DO. Notably, the 2022 data showed minimal correlations (except SSs) due to high baseline pollution, whereas the post-remediation 2023 data revealed stronger linear linkages (especially r = −0.81 for SSs). The proposed “high-frequency localization–low-frequency assessment” detection method demonstrated robust accuracy in identifying hypoxia events, and mechanistic analysis corroborated the time-lagged pollutant impacts. These findings advance hypoxia identification frameworks and highlight the critical role of Turbidity and SSs in driving estuarine oxygen depletion, offering actionable insights for adaptive water quality management. Full article

Olive mill wastewater (OMWW) has high energetic potential due to its organic load, but its complex composition and toxicity limit efficient energy recovery. This study proposes an innovative integrated process combining continuous resin adsorption with anaerobic digestion to detoxify OMWW and recover renewable energy simultaneously. It studies the recovery of polyphenols, methane production, and substrate degradation efficiency using resin column bed heights (C1: 5.7 cm, C2: 12.1 cm, C3: 18.5 cm), as well as kinetic modeling of organic matter degradation. Adsorption reduced chemical oxygen demand (COD) by up to 80% and polyphenols by up to 64%, which significantly improved substrate biodegradability from 34% to 82%, corresponding to a methane yield of 287 mL CH₄/g COD. Organic matter was fractioned into rapid (S₁), moderate (S₂), and slow (S₃) biodegradable fractions. The highest degradation kinetics was C3, with methane production rates of K₁ = 23.86, K₂ = 2.47, and K₃ = 2.92 mL CH₄/d. However, this condition produced the lowest volumetric methane production due to excessive COD removal, including readily biodegradable matter. These results highlight the importance of optimizing the adsorption step in order to find to a balance between detoxification and energy recovery from OMWW, thus supporting the principles of circular economy and promoting renewable energy production. Full article

With the rapid development of the livestock farming industry, the treatment of livestock farming wastewater has become increasingly important. The microbial-algal biofilm method has gained widespread attention for cattle wastewater treatment owing to its non-toxic nature, resistance to shock loading, and high treatment efficiency. In this study, three types of substrates—polyurethane sponge, ceramic material, and moving bed biofilm reactor media—were evaluated. The formation of biofilms was assessed through variations in chlorophyll content, microscopic observations, and measurements of biofilm dry weight and attachment rate. Biofilm characterization on the different substrates was conducted via Fourier transform infrared spectroscopy, confocal laser scanning microscopy, and scanning electron microscopy. The results demonstrated that polyurethane sponge was the most effective substrate. Furthermore, a single-factor experiment was conducted to optimize the cultivation conditions for the microbial-algal biofilms and identify the optimal parameters based on the ability of the biofilm to remove COD, TN, TP, and NH₄⁺-N. The optimal conditions were as follows: an illumination intensity of 8000 lux, red light, a temperature of 20 °C, a pH of 7, and an aeration intensity of 8 L/min. Under these conditions, the pollutant removal rates were exceptionally high: ~73.4% for COD, 51.8% for TP, 57.0% for TN, and 75.1% for NH₄⁺-N. Full article

This study evaluated the pollutant removal efficiency of two decentralized wastewater treatment plants (WWTPs) located in the high-altitude southern Andes of Ecuador, Acchayacu and Churuguzo, from 2015 to 2024. Acchayacu previously operated using an upflow anaerobic filter (UAF), and from 2021, it transitioned to using vertical-subsurface-flow constructed wetlands (VSSF-CWs). In contrast, Churuguzo employs surface-flow constructed wetlands (SF-CWs). These systems were assessed based on parameters such as the five-day biochemical oxygen demand (BOD₅), chemical oxygen demand (COD), total phosphorus, organic nitrogen, ammonia nitrogen, total solids, fecal coliforms (TTCs), and total coliforms (TCs). The data were divided into two subperiods to account for the change in technology in Acchayacu. Statistical analysis was conducted to determine whether significant differences existed between the treatment efficiencies of these technologies, and the SF-CW was found to consistently outperform both the UAF and VSSF-CW in removing organic matter and microbial pollutants. This difference is likely attributed to the longer hydraulic retention time, lower hydraulic loading rate, and vegetation type. The findings highlight the environmental implications of treatment technology selection in WWTPs, particularly regarding the quality of receiving water bodies and their potential applications for public health, proper water resource management, and the design of decentralized systems in high-altitude regions, especially in developing countries. Full article

Against the backdrop of China’s “dual carbon” strategy, investigating the carbon emission characteristics and low-carbon operational status of wastewater treatment plants (WWTPs) across regions is pivotal for achieving synergistic pollution reduction and carbon mitigation. Leveraging 2024 operational data from 98 WWTPs in eastern China—encompassing treatment volume, energy consumption, sludge production, and chemical dosages—this study refined the Assessment Standard for Carbon Mitigation in Municipal WWTPs and Technical Specification for Low-Carbon Operation of WWTPs. A novel carbon accounting framework and low-carbon performance evaluation system were subsequently developed to analyze the impacts of treatment scale, technological configuration, and load rate on carbon footprints. Key findings revealed an average carbon intensity of 0.399 kg CO₂-eq/m³ for the region, with small-scale facilities (0.582 kg CO₂-eq/m³) exhibiting significantly higher emissions compared to their large-scale counterparts (0.392 kg CO₂-eq/m³). Indirect emissions constituted 62.1% of the total footprint, while chemical dosing contributed 14.2%, primarily driven by carbon sources and phosphorus removal agents. Fossil-derived CO₂ accounted for 4.6% of emissions. Notably, the AAO process demonstrated the lowest carbon intensity (0.370 kg CO₂-eq/m³), whereas SBR systems registered the highest (0.617 kg CO₂-eq/m³). Furthermore, 25% of the assessed facilities were classified as high-emission plants. Strategic recommendations are proposed, including prioritizing AAO process optimization, implementing intelligent chemical dosing control, utilizing food wastewater as an alternative carbon source, and enhancing operational load rates, to advance synergistic environmental and carbon mitigation goals in eastern China’s wastewater sector. Full article