Search Results (20)

This study investigates the primary electromagnetic sources of acoustic noise in single-phase induction motors and proposes design-oriented strategies for noise reduction. A 370 W, four-pole, 80-frame single-phase induction motor was designed, analyzed, and experimentally validated. Finite Element Method (FEM) simulations were conducted using Ansys Maxwell 2D to examine the effects of magnetic field distortion, magnetic saturation, and rotor eccentricity on torque ripple and inductance variation. The results demonstrate that these factors significantly increase electromagnetic force harmonics acting on the stator teeth and frame, leading to vibration and acoustic noise generation. In addition, inductance fluctuations caused by interphase magnetic coupling and air-gap harmonics were found to increase current harmonic content and potentially excite structural resonances. The influence of capacitor selection and winding configuration on magnetic saturation, phase displacement, and torque ripple was systematically evaluated. Prototype motors were manufactured and acoustic noise measurements were performed to experimentally validate the simulation results. Unlike previous studies that often investigate these parameters separately, this work presents a coupled analysis that explicitly links capacitor selection, winding configuration, and rotor eccentricity to inductance variation, torque ripple, and acoustic noise generation. The findings provide practical design guidelines for the development of low-noise single-phase induction motors and contribute to reducing electromagnetic vibration and acoustic emissions in electric machine design. Full article

The rapid electrification of road vehicles has fundamentally reshaped the priorities of noise, vibration, and harshness (NVH) engineering. In the absence of combustion-related broadband masking, tonal and order-related phenomena originating from the electric machine, inverter switching, and high-speed reduction gearing have become clearly perceptible and, in many cases, acoustically dominant. Consequently, drivetrain noise in electric vehicles can no longer be assessed at component level alone; it must be understood as a coupled system response shaped by excitation mechanisms, structural dynamics, transfer paths, radiation efficiency, and ultimately human perception. This review adopts a source-to-perception perspective and consolidates the principal physical mechanisms governing vibro-acoustic behavior in integrated electric drive units. Electromagnetic force harmonics and torque ripple are discussed alongside transmission-error-driven gear mesh excitation, while bearing and shaft nonlinearities are examined in the context of high-speed operation. In addition, ancillary thermoacoustic and aerodynamic contributions are considered, reflecting the increasingly integrated packaging of modern e-axle architectures. On this mechanism-oriented basis, dominant excitation types are linked to frequency-appropriate modeling strategies, spanning electromagnetic force extraction, multibody drivetrain simulation, structural finite element analysis, transfer path analysis, and acoustic radiation prediction. Particular attention is given to workflow integration across domains. Finally, the paper identifies research challenges that predominantly arise at system level, including multi-source interaction effects, installation-dependent transfer-path variability, emergent resonances in assembled structures, manufacturing-induced tonal artifacts, and the still limited correlation between predicted vibration fields and perceived sound quality. Full article

This paper presents an efficient stand-alone photovoltaic water pumping system (PVWPS) intended for agricultural irrigation applications, operating without energy storage. The system employs a three-phase induction motor supplied by a three-level neutral point clamped (NPC) inverter. The proposed control strategy integrates the advantages of two distinct controllers to enhance both energy extraction and drive performance. On the photovoltaic side, a fuzzy logic-based maximum power point tracking (MPPT) algorithm is implemented to ensure continuous operation at the global maximum power point under rapidly varying irradiance conditions. On the motor drive side, a direct torque control (DTC) scheme is combined with the multilevel NPC inverter to regulate electromagnetic torque and stator flux. The use of a multilevel inverter significantly mitigates the inherent drawbacks of conventional DTC, notably torque and flux ripples, as well as stator current harmonic distortion. The overall control architecture maximizes power transfer from the photovoltaic generator to the pumping system, resulting in improved dynamic response and energy efficiency. The proposed system is validated through detailed MATLAB/Simulink simulations under abrupt irradiance variations and a realistic daily solar profile corresponding to August conditions in Kairouan, Tunisia. Simulation results demonstrate substantial performance improvements, including an 88% reduction in torque ripples, a 50% decrease in flux ripple, a 77.9% reduction in stator current THD, and a 33.3% enhancement in speed transient response compared to conventional DTC-based systems. Full article

Common-mode voltage (CMV) is a critical concern in motor drive applications employing multilevel inverters, as it can lead to significant issues such as high-frequency noise, electromagnetic interference, and motor bearing degradation. These effects can compromise the reliability, reduce the operational lifespan of electric machines, and introduce safety hazards. In this study, an enhanced Direct Torque Control (DTC) strategy incorporating Space Vector Modulation (SVM) is proposed to specifically address CMV-related challenges in induction motors (IM) driven by a three-level Neutral-Point-Clamped (NPC) inverter. The proposed DTC scheme utilizes a specialized modulation technique that effectively mitigates CMV while also minimizing current harmonic content, and torque and flux ripples with a constant switching frequency. The developed SVM algorithm simplifies the three-level space vector representation into six equivalent two-level diagrams, enabling more efficient control. The zero-voltage vector is synthesized virtually by combining two active vectors within a two-level hexagonal structure. The effectiveness of the proposed DTC approach is validated through both simulation and Hardware-In-the-Loop (HIL) testing. Compared to the conventional DTC method, the proposed solution demonstrates superior performance in CMV minimization and leakage current reduction. Notably, it limits the CMV amplitude to V_dc/6, a significant improvement over the V_dc/2 typically observed with the standard DTC approach. Full article

This paper proposes an event-triggered extension of duty-ratio-based model predictive direct speed control (DR-MPDSC) for permanent magnet synchronous motor (PMSM) drives in electric vehicle (EV) applications. The main contribution is the development of an event-triggered execution framework specifically tailored to DR-MPDSC, in which control updates are performed only when the speed tracking error violates a prescribed condition, rather than at every sampling instant. Unlike conventional MPDSC and time-triggered DR-MPDSC schemes, the proposed strategy achieves a significant reduction in control execution frequency while preserving fast dynamic response and closed-loop stability. An optimized duty-ratio formulation is employed to regulate the effective application duration of the selected voltage vector within each sampling interval, resulting in reduced electromagnetic torque ripple and improved stator current quality. An extended Kalman filter (EKF) is integrated to estimate rotor speed and load torque, enabling disturbance-aware predictive speed control without mechanical torque sensing. Furthermore, a unified field-weakening strategy is incorporated to ensure wide-speed-range operation under constant power constraints, which is essential for EV traction systems. Simulation and experimental results demonstrate that the proposed event-triggered DR-MPDSC achieves steady-state speed errors below 0.5%, limits electromagnetic torque ripple to approximately 2.5%, and reduces stator current total harmonic distortion (THD) to 3.84%, compared with 5.8% obtained using conventional MPDSC. Moreover, the event-triggered mechanism reduces control update executions by up to 87.73% without degrading transient performance or field-weakening capability. These results confirm the effectiveness and practical viability of the proposed control strategy for high-performance PMSM drives in EV applications. Full article

To address the significant vibration and noise problems caused by the zero-order radial electromagnetic force (REF) in integer-slot permanent magnet synchronous motors (PMSMs), while simultaneously improving the motor’s overall electromagnetic performance, this paper proposes a hierarchical iterative optimization strategy integrating Taguchi methods and genetic algorithms. The optimization objectives include minimizing the zero-order REF amplitude, cogging torque, and torque ripple, while maximizing the average torque, with efficiency and back electromotive force total harmonic distortion (back-EMF THD) treated as constraints. First, an 8-pole 48-slot double-layer embedded PMSM model is constructed. An innovative parameter selection strategy, combining theoretical analysis with finite-element analysis, is employed to investigate the spatial order and frequency characteristics of the electromagnetic force. Subsequently, a sensitivity analysis is performed to stratify parameters: highly sensitive parameters undergo first-round optimization via the Taguchi method, followed by second-round optimization using a multi-objective genetic algorithm. The results demonstrate significant reductions in both the zero-order REF amplitude and cogging torque. Specifically, the motor’s peak vibration acceleration is reduced by 32.96%, and the peak sound pressure level (SPL) drops by 9.036 dB. Vibration acceleration and sound pressure across all frequency bands are significantly reduced to varying extents, validating the effectiveness of the proposed optimization approach. Full article

Direct power control (DPC) is a widely accepted control scheme utilized in renewable energy applications owing to its several advantages over other control mechanisms, including its simplicity, ease of implementation, and faster response. However, DPC suffers from inherent drawbacks and limitations that constrain its applicability. These restrictions include notable ripples in active power and torque, as well as poor power quality brought on by the usage of a hysteresis regulator for capacity management. To address these issues and overcome the limitations of DPC, this study proposes a novel approach that incorporates artificial neural networks (ANNs) into DPC. The proposed technique focuses on doubly fed induction generators (DFIGs) and is validated through experimental testing. ANNs are employed to recompense for the deficiencies of the hysteresis controller and switching table. The intelligent DPC technique is then compared to three other strategies: classic DPC, backstepping control, and integral sliding-mode control. Various tests are conducted to compare the ripple ratio, current quality, durability, response time, and reference tracking. The validity and robustness of the proposed intelligent DPC for DFIGs are verified through both simulation and experimental results obtained from the MATLAB/Simulink environment and the Real-Time Interface (RTI) of the dSPACE DS1104 controller card. The results confirm that the intelligent DPC outperforms conventional control strategies in terms of stator current harmonic distortion, dynamic response, power ripple minimization, reference tracking accuracy, robustness, and overshoot reduction. Overall, the intelligent DPC exhibits superior performance across all evaluated criteria compared to the alternative approaches. Full article

Ripples in the electromagnetic torque of electric vehicle (EV) motors due to poor stator voltage and control cause jerky movements, equipment failure, discomfort for passengers and drivers, and damage to the associated civil works. This paper presents the implementation of Finite Control Set Model Predictive Control (FCSMPC) for a high-level modified W-type inverter (MWI) driving a three-phase induction motor (IM), along with validation of its performance. The proposed control strategy aims to minimize motor torque ripples and has been tested under various driving torque patterns. The results demonstrate a significant reduction in torque ripples—down to less than 1%—and acceptable levels of total harmonic distortion (THD), as verified through quality analysis of the stator currents. Moreover, a comparative assessment of voltage profiles for the electromagnetic torque and rotor speed curves has been presented for nine cases of simultaneous variations in multiple motor parameters; the results indicate that the MWI-fed motor has the best performance and the lowest sensitivity to the variations. Full article

Multiphase electric drives (EDs) offer important advantages for high-demand applications. However, they require appropriate high-performance control strategies. In this context, finite-control-set model predictive control (FCS-MPC) emerges as a promising strategy, offering a notable flexibility to implement multiobjective regulation schemes. When applied to multiphase EDs, standard FCS-MPC exhibits degraded current quality at low and medium control frequencies. Multivector solutions address this issue by properly combining multiple voltage vectors within a single control period to create the so-called virtual voltage vectors (VVVs). In this way, this approach achieves flux and torque regulation while minimizing current injection into the secondary subspace. For this purpose, the VVV synthesis typically prioritizes active vectors with low contribution in secondary subspaces, avoiding the average deception phenomenon. VVV solutions commonly enable an open-loop regulation of secondary currents. Nevertheless, the absence of closed-loop control in the secondary subspace hinders the compensation of nonlinearities, machine asymmetries, and unbalanced conditions in the ED. Considering this scenario, this work implements a multivector FCS-MPC recovering closed-loop control for the secondary subspace. The capability of the proposal to mitigate secondary current injection and compensate for possible dissymmetries is experimentally evaluated in a six-phase ED. Its performance is compared against a benchmark technique in which secondary current regulation is handled in open-loop mode. The proposed control solution significantly improves in current quality, achieving a reduction in harmonic distortion of 54% at medium speed. Full article

This paper presents an accurate analysis of the power losses of an interior permanent magnet synchronous motor fed by a cascaded H-bridge multilevel inverter. The main goal of this study is to investigate the impact of the cascaded h-bridge inverter, multicarrier PWM strategies, and inverter switching frequency on the synchronous motor power losses. With this aim in mind, a detailed frequency domain power analysis was carried out on motor power losses at different operating points in the frequency–torque plane. Motor power losses were further categorized into fundamental and harmonic power losses. This evaluation involved driving the power converter using six distinct multicarrier PWM strategies at four different switching frequencies. Additionally, a comparison was conducted with a conventional two-level PWM inverter to quantify the reduction in motor power losses. The experimental results show that the cascaded h-bridge inverter guarantees a notable increase in the motor efficiency, up to 7%, and losses in segregation at the fundamental frequency, if compared to the standard two-level PWM inverter, especially at low speed and with partial-load conditions. Such results mark out the cascaded H-bridge inverter as a valuable choice, also with regard to low-voltage drive applications. Full article

Variable Flux Reluctance Machines (VFRMs) face multiple interconnected challenges that limit their performance, particularly in high-performance applications such as electric vehicles (EVs), where smooth torque output and robust operation are critical. Chief among these challenges are complex inter-axis couplings, including cross-coupling in the dq-axis, differential term coupling in the d0-axis, and disturbances propagating from the 0-axis to the q-axis. Additionally, harmonic disturbances associated with torque ripple exacerbate performance issues, resulting in degraded dynamic behavior. These challenges hinder current loop controllers, preventing effective management of winding impedance voltage drops and inter-axis coupling terms without advanced decoupling strategies. To address these challenges, this paper proposes a novel integrated torque harmonic extended state observer (ITHESO) within a decoupled current control designed to ensure fast and accurate current tracking, system stability, and torque ripple reduction. The ITHESO identifies and compensates for total current disturbances, including harmonic components, through feed-forward compensation within the current loop. Furthermore, the influence of control parameters and the effects of parameter mismatches on stability, torque ripple reduction, and disturbance rejection are thoroughly analyzed. Experimental validations demonstrate that the proposed strategy significantly enhances torque dynamics and reduces torque ripple, outperforming the conventional Active Disturbance Rejection Control (ADRC), which does not explicitly address disturbances associated with torque ripple. These advancements position the VFRM with the ITHESO as a competitive option for high-performance EV propulsion systems, offering smooth operation, noise reduction, and reliable performance under varying speeds and loads. Full article

This paper presents a carrier waves phase shifting method to reduce the dc-link capacitor current for a dual three-phase permanent magnet synchronous motor drive system. Dc-link capacitors absorb the ripple current generated at the input due to the harmonics of the pulse width modulation (PWM). The size, cost, reliability, and lifetime of the dc-link capacitor are negatively affected by this ripple current flowing through it. The proposed method is especially appropriate for common dc-link capacitors for a dual inverter system driving two PMSMs. In this paper, the input current of each inverter is analyzed using Double Fourier Analysis, and the harmonic components of the dc-link capacitor current are determined. The carrier wave phase shifting method is proposed to reduce the magnitude of the harmonics and thus reduce the dc-link capacitor current. Furthermore, the optimum angle between the carrier waves for the maximum reduction in the dc-link capacitor current is analyzed and simulated for different scenarios considering the speed and load torque of the PMSMs. The proposed method is verified through experiments and PMSMs are driven by three-phase voltage source inverters (VSIs) modulated with Space Vector Pulse Width Modulation (SVPWM), which is the most common PWM strategy. The proposed method reduces the dc-link capacitor current by 60%, thereby significantly decreasing the required dc-link capacitance, the volume of the drive system, and its cost. Full article

In this work, the application of a sliding mode equivalent control for an induction motor drive based on a multi-pulse Voltage Source Converter is proposed. This is accomplished by transforming the squirrel-cage induction motor mathematical model into a block control form. The equivalent control method is applied to the sliding manifold, where the voltages are obtained in the stationary reference frame to control the angular velocity of the motor. In addition, a proportional-integral control is designed and applied to the motor represented in this form in order to make performance comparisons with the equivalent control method. Multi-pulse converters of 6, 12, and 84 pulses are used directly to feed the plant that is being controlled. The outcomes of using these power electronics devices are used to perform comparisons among the velocity tracking performance, control voltages in stationary reference frame, tracking errors, and rejection of external disturbances. Furthermore a dynamic and steady-state analysis of the velocity tracking performance is executed. The energy profiles for the startup, torque variations, and steady-state are also obtained. Additionally, total harmonic distortion values are added. All comparisons are carried out using the established plan for the motor, both with and without the use of power electronics converters, and with both control algorithms. The obtained results demonstrate that the use of a high-quality voltage source converter, along with a good control strategy, allows for a general improvement in the overall system and a significant reduction in energy usage, whilst also reducing controller complexity. Full article

The cogging torque reduction methods in permanent magnet (PM) machines are more or less FEA trial and error-based and cause undesirable side effects, such as distorted back EMF, new harmonic components, and structure asymmetry. A slot-opening grouping method can address these issues. However, it needs to model all slots in FEA design validation during practical cogging torque optimization iterations, and also leads to back-EMF reduction. In this paper, a new grouping strategy, termed in-phase unit (IPU), is introduced, together with the slot-opening angle-shift method. The slot openings with the same cogging torque distribution pattern are grouped into an IPU, and the cogging torque peaks of the slot openings within an IPU can now be interleaved. Thereby, the major harmonic components of the cogging torque are cancelled out, instead of being summed up. The IPU grouping principle, the slot-opening shift angle computation, and the selection of the harmonic order to cancel are analyzed in detail. By comparison, the proposed method not only simplifies cogging torque optimization iterations by only modeling the slots in one IPU in FEA, but also compensates for the back-EMF constant reduction. The effectiveness of the proposed methods is validated by two typical interior PM machine design cases. Full article

In this paper, a discrete skew methodology is presented to understand the effect of skewing angle on electromagnetic torque in SynRM design. A new approach is proposed to estimate the amplitude of each torque ripple component as a function of skewing angle. The reduction factor for each harmonic component is derived in general form, allowing for the determination of overall torque ripple waveform. The validity of the proposed method is evaluated through the examination of two SynRMs, resulting in a torque ripple reduction of up to 70%. The results obtained through the use of a proposed analytical ripple reduction estimator and FEA evaluation showed good agreement. The proposed skewing technique was applied on a previously optimized triple-barrier SynRM with a positive outcome: a consistent torque ripple reduction tackling relevant harmonic components. The analysis of harmonic distribution of torque ripple is mandatory for the selection of the optimal skewing strategy when following the proposed method, with two-step skewing recommended for mostly-purely-sinusoidal torque waveforms, and multi-step skewing recommended for machines with multiple higher-magnitude harmonic components. Full article