Search Results (1,332)

To reveal the influence mechanisms of seasonal climatic factors (wind speed, wind direction, temperature) and leakage direction on hydrogen dispersion and explosion behavior from single-source leaks at typical risk locations (hydrogen storage tanks, compressors, dispensers) in hydrogen refueling stations (HRSs), this work established a full-scale 1:1 three-dimensional numerical model using the FLACS v22.2 software based on the actual layout of an HRS in Xichang, Sichuan Province. Through systematic simulations of 72 leakage scenarios (3 equipment types × 4 seasons × 6 leakage directions), the coupled effects of climatic conditions, equipment layout, and leakage direction on hydrogen dispersion patterns and explosion risks were quantitatively analyzed. The key findings indicate the following: (1) Downward leaks (−Z direction) from storage tanks tend to form large-area ground-hugging hydrogen clouds, representing the highest explosion risk (overpressure peak: 0.25 barg; flame temperature: >2500 K). Leakage from compressors (±X/−Z directions) readily affects adjacent equipment. Dispenser leaks pose relatively lower risks, but specific directions (−Y direction) coupled with wind fields may drive significant hydrogen dispersion toward station buildings. (2) Southeast/south winds during spring/summer promote outward migration of hydrogen clouds, reducing overall station risk but causing localized accumulation near storage tanks. Conversely, north/northwest winds in autumn/winter intensify hydrogen concentrations in compressor and station building areas. (3) An empirical formula integrating climatic parameters, leakage conditions, and spatial coordinates was proposed to predict hydrogen concentration (error < 20%). This model provides theoretical and data support for optimizing sensor placement, dynamically adjusting ventilation strategies, and enhancing safety design in HRSs. Full article

In tunnel blasting, an analytical solution for dynamic stress in the surrounding rock of adjacent tunnels is critical for dynamic response analysis, mechanical evaluations, and crack propagation control. Previous studies on stress field analytical solutions primarily modeled rock as a linear elastic material, focusing mainly on the P-wave effects from instantaneous detonation. Based on Heelan’s short cylindrical cavity model, this paper derives an analytical solution for blast-induced dynamic stresses in adjacent tunnel rock, incorporating both induced SV-waves and a rock mass damage factor through rigorous theoretical analysis. Numerical case studies and field measurements were used to analyze stress propagation during tunnel blasting, and theoretical results were compared with measured data. The key findings were as follows: Radial stress > axial stress > hoop stress. All three stresses decay with increasing distance and damage factor, following an inversely proportional relationship with distance. Radial stress decays faster than axial and hoop stresses. Stress also decays exponentially over time, with the peak occurring after the transverse wave arrival. The theoretical results show approximately 10% deviation from the existing empirical formulas, while field measurements closely match the theoretical model, showing consistent stress trends and an average error of 7.02% (radial), 7.56% (axial) and 7.05% (hoop), confirming the reliability of the proposed analytical solution. Full article

To solve the limitations of these models for submicron materials like electrospun nanofiber membranes, a numerical simulation was used to construct a three-dimensional model closer to the actual structure to explore the filtration resistance and efficiency of these membranes. Based on the actual polydisperse electrospun nanofiber filter, the three-dimensional structure (fiber diameter 280 nm–1300 nm, thickness 0.0150 mm–0.0240 mm, and solid volume fraction 11.3–17.7%) was reconstructed by GeoDict software. The filtration resistance was simulated with the FlowDict module (surface velocity 6.89 cm/s, 20 °C), and the filtration efficiency was calculated with the FilterDict module (2.5 μm particles, tracking 20,000). The results are compared with the experimental values, Davids empirical formula, Happel model, and Kuwabara model. The results show that the simulated values of filtration resistance are generally higher than the experimental values (deviation ≤ 20%), among which the simulation and experiment have the highest consistency, followed by the Davids formula (such as the relative error of 41.62% at 9% spinning solution concentration), and the Kuwabara model has the largest error (59.86%). The simulated value of filtration efficiency is higher than the experimental value (deviation ≤ 7%), because the model assumes that the particles adhere directly after contacting the fiber, and the actual sliding off is not considered. This study confirms that numerical simulation can efficiently predict the filtration performance of electrospun nanofiber membranes. Therefore, it provides a basis for optimizing material structure by adjusting spinning parameters and promoting the engineering application of submicron filter materials. Full article

This paper develops an analytical pricing formula for vulnerable options with stochastic volatility under a two-factor stochastic interest rate model. We consider the underlying asset price following the Heston stochastic volatility model, while the interest rate is modeled as the sum of two processes. Using the joint characteristic function approach and measure change techniques, we derive an explicit pricing formula for a vulnerable European option. We also conduct numerical experiments to examine the effects of various model parameters on option values. This study provides a more realistic framework for pricing OTC derivatives by incorporating credit risk, stochastic volatility, and stochastic interest rates simultaneously. Full article

Background/Objectives: Maxillofacial silicone prostheses’ long-term color stability remains a challenge. This study aimed to evaluate and compare the color stability of conventional and digital maxillofacial silicone elastomers mixed with nano-sized antimicrobial additives (ZnO nanoparticles and chlorhexidine salt-CHX) at various concentrations over a 10-week period. Methods: A total of nine groups (n = 10) of maxillofacial silicone elastomers were prepared. These included a control group (no additives), conventionally pigmented silicone, digitally pigmented silicone (Spectromatch system), and silicone mixed with ZnO or CHX at 1%, 3%, and 5% by weight. Specimens were fabricated in steel molds and cured at 100 °C for 1 h. Color measurements were performed at baseline and after 1, 4, 6, and 10 weeks using a Minolta Chroma Meter (CIELAB system, ΔE₀₀ formula). Data were analyzed using two-way ANOVA and Tukey HSD post hoc tests (α = 0.05). Results: Color changes (ΔE₀₀) ranged from 0.74 to 2.83 across all groups. The conventional pigmented silicone group showed the highest color difference (ΔE₀₀ = 2.83), while the lowest was observed in the ZnO 1% group (ΔE₀₀ = 0.74). Digital silicone and all antimicrobial-modified groups exhibited acceptable color stability (ΔE₀₀ < 3.1). Time significantly affected color difference, with the largest change occurring during the first four weeks (p < 0.05), followed by stabilization. Regression analysis confirmed high color stability over time for all groups except the conventional pigmented group. Conclusions: This is one of the first studies to directly compare digital and conventional pigmentation methods combined with nano-antimicrobials in maxillofacial silicones. Maxillofacial silicone elastomers mixed with up to 5% ZnO or CHX maintained acceptable color stability over 10 weeks. Digital pigmentation is similar to conventional methods. The incorporation of nano-antimicrobials offers significant microbial resistance and improved color retention. Full article

Background: Pleural mesothelioma (PM) is a type of cancer that is difficult to diagnose and treat. Patients may have vastly varying prognoses, and prognostic factors may help guide the clinical approach. As a recently identified biomarker, the pan-Immune-Inflammation-Value (PIV) is a simple, comprehensive, and peripheral blood cell-based biomarker. Methods: The present study represents a retrospective observational analysis carried out within a single-center setting. Ninety-five patients with PM stages I–IV were enrolled in the study. We analyzed the correlation between patients’ demographic characteristics, clinicopathological factors such as histological subtypes, surgery status, tumor thickness, blood-based parameters, and treatment options with their prognoses. PIV was calculated by the following formula: (neutrophil count × monocyte count × platelet count)/lymphocyte count. Additionally, blood-based parameters were used to calculate the platelet-to-lymphocyte ratio (PLR), neutrophil-to-lymphocyte ratio (NLR), and systemic immune inflammation index (SII). Results: We categorized the patients into two groups, low PIV group (PIV ≤ 732.3) and high PIV group (PIV > 732.3) according to the determined cut-off value, which was defined as the median. It was revealed that high PIV was associated with poor survival outcomes. The median follow-up period was 15.8 months (interquartile range, IQR, 7.1 to 29.8 months). The median overall survival (OS) was significantly longer in patients in the low PIV group (median 29.8 months, 95% confidence interval (CI), 15.6 to 44) than the high PIV group (median 14.7 months, 95% CI, 10.8 to 18.6 p < 0.001). Furthermore, the study revealed that patients with low PIV, NLR, and SII values were more likely to be eligible for surgery and were diagnosed at earlier stages. Additionally, these markers were identified as potential predictors of disease-free survival (DFS) in the surgical cohort and of treatment response across the entire patient population. Conclusions: In addition to well-established clinical factors such as stage, histologic subtype, resectability, and Eastern Cooperative Oncology Group (ECOG) performance status (PS), PIV emerged as an independent and significant prognostic factor of overall survival (OS) in patients with PM. Moreover, PIV also demonstrated a remarkable independent prognostic value for disease-free survival (DFS) in this patient population. Additionally, some clues are provided for conditions such as treatment responses, staging, and suitability for surgery. As such, in this cohort, it has outperformed the other blood-based markers based on our findings. Given its ease of calculation and cost-effectiveness, PIV represents a promising and practical prognostic tool in the clinical management of pleural mesothelioma. It can be easily calculated using routinely available laboratory parameters for every cancer patient, requiring no additional cost or complex procedures, thus facilitating its integration into everyday clinical practice. Full article

Background: Neonatal jaundice is common and can cause severe hyperbilirubinemia if untreated. The early identification of at-risk newborns is challenging despite the existing guidelines. Objective: This study aimed to identify the key maternal and neonatal risk factors for jaundice requiring phototherapy using machine learning. Methods: In this study hospital, phototherapy was administered following the American Academy of Pediatrics (AAP) guidelines when a neonate’s transcutaneous bilirubin level was in the high-risk zone. To identify the risk factors for phototherapy, we retrospectively analyzed the electronic medical records of 8242 neonates admitted between 2017 and 2022. Predictive models were trained using maternal and neonatal data. XGBoost showed the best performance (AUROC = 0.911). SHAP values interpreted the model. Results: Mode of delivery, neonatal feeding indicators (including daily formula intake and breastfeeding frequency), maternal BMI, and maternal white blood cell count were strong predictors. Cesarean delivery and lower birth weight were linked to treatment need. Conclusions: Machine learning models using perinatal data accurately predict the risk of neonatal jaundice requiring phototherapy, potentially aiding early clinical decisions and improving outcomes. Full article

Leishmaniasis is an infectious disease common in tropical and subtropical regions worldwide. This study aimed to develop a topical meglumine antimoniate gel (MA-gel) for the treatment of cutaneous leishmaniasis. The MA-gel was characterized in terms of morphology, pH, swelling, porosity, rheology, and thermal properties by differential scanning calorimetry (DSC). Biopharmaceutical evaluation included in vitro drug release and ex vivo skin permeation. Safety was evaluated through biomechanical skin property measurements and cytotoxicity in HaCaT and RAW 267 cells. Leishmanicidal activity was tested against promastigotes and amastigotes of Leishmania infantum, and in silico studies were conducted to explore possible mechanisms of action. The composition of the MA-gel included 30% MA, 20% Pluronic^® F127 (P407), and 50% water. Scanning electron microscopy revealed a sponge-like and porous internal structure of the MA-gel. This formula exhibited a pH of 5.45, swelling at approximately 12 min, and a porosity of 85.07%. The DSC showed that there was no incompatibility between MA and P407. Drug release followed a first-order kinetic profile, with 22.11 µg/g/cm² of the drug retained in the skin and no permeation into the receptor compartment. The MA-gel showed no microbial growth, no cytotoxicity in keratinocytes, and no skin damage. The IC₅₀ for promastigotes and amastigotes of L. infantum were 3.56 and 23.11 µg/mL, respectively. In silico studies suggested that MA could act on three potential therapeutic targets according to its binding mode. The MA-gel demonstrated promising physicochemical, safety, and antiparasitic properties, supporting its potential as a topical treatment for cutaneous leishmaniasis. Full article

In 2071, the Hydraulic community will commemorate the second centenary of the Baré de Saint-Venant equations, also known as the Shallow Water Equations (SWE). These equations are fundamental to the study of open-channel flow. As non-linear partial differential equations, their solutions were largely unattainable until the development of computers and numerical methods. Following 1960, various numerical schemes emerged, with Preissmann’s scheme becoming the most widely employed in many software applications. In the 1990s, some researchers identified a significant limitation in existing software and codes: the inability to simulate transcritical flow. At that time, Preissmann’s scheme was the dominant method employed in hydraulics tools, leading the research community to conclude that this scheme could not handle transcritical flow due to suspected instability. In response to this concern, several researchers suggested modifications to Preissmann’s scheme to enable the simulation of transcritical flow. This paper will demonstrate that these accusations against the Preissmann scheme are unfounded and that the proposed improvements are unnecessary. The observed instability is not due to the numerical method itself, but rather a mathematical instability inherent to the SWE, which can lead to ill-posed conditions if a specific derived condition is not met. In the context of a friction slope formula based on Manning or Chézy types, the condition for ill-posedness of the 1D shallow water equations simplifies to the Vedernikov number condition, which is necessary for roll waves to develop in uniform flow. This derived condition is also relevant for the formation of roll waves in unsteady flow when the 1D shallow water equations become ill-posed. Full article

This study assesses the quality of fat in conventional and specialist infant formulas (IFs) available in Poland. The IFs studied were characterized in terms of fatty acid profiles and lipid quality indices. The study material consisted of eight types of conventional and specialist IFs. The determination of fatty acids was carried out using gas chromatography (GC). Lipid quality indices were estimated based on established formulas. Goat milk-based formulas showed significantly higher levels of caproic acid (C6:0) and capric acid (C10:0) than cow milk-based formulas of the same category (initial or follow-on) (p < 0.05). In addition, these IFs stood out in terms of conjugated linoleic acid (CLA) content (0.30%) compared to cow and specialist formulas (about 0.20%). It was shown that the average ratio of n6/n3 fatty acids was significantly lower in conventional IFs (6.07:1) compared to specialist IFs (8.10:1). The goat’s milk-based IFs had the most favorable values for individual lipid quality indices (index of desirable fatty acids (DFAs) = 62.46; index of hypercholesterolemic fatty acids (OFAs) = 25.94; index of atherogenicity (AI) = 0.71; index of thrombogenicity (TI) = 0.88; hypocholesterolemic/hypercholesterolemic ratio (H/H) = 2.05), while the specialist S-PH formula was characterized by the lowest DFA value (49.17) and the highest AI and TI indices (1.48 and 1.68). Multivariate analysis clearly classified the division of formulas into two groups—conventional and specialist—based on lipid quality indices. The results obtained provide new information on the variation in the lipid profile of IFs depending on the intended use of the formula and may serve as a basis for further research in this area. Full article

Research on the grouting reinforcement mechanism of overburden is constrained by the concealed and heterogeneous nature of geotechnical media, posing dual challenges in theoretical analysis and process visualization. Based on discrete element numerical simulations and laboratory tests, an analytical model for grouting reinforcement in overburden layers is developed, revealing the influence of grouting pressure on slurry diffusion shape and distance. The results indicate the following: (1) Contact parameters of overburden and cement particles were obtained through laboratory tests. A grouting model for the overburden layer was established using the discrete element method. After optimizing particle coarsening and the contact model, the simulation more accurately represented slurry diffusion characteristics such as compaction, splitting, and permeability. (2) By monitoring porosity and coordination number distributions near grouting holes before and after injection using circular measurement, the discrete element simulation clearly visualizes the slurry reinforcement range. The reinforcement mechanism is attributed to the combined effects of pore structure compaction (reduced porosity) and cementation within the overburden (increased coordination number). (3) Based on slurry diffusion results, a functional relationship between slurry diffusion radius and grouting pressure is established. Error analysis shows that the modified formula improves the goodness of fit by 34–39% compared to the classical formula (Maag, cylindrical diffusion). The discrete element analysis method proposed in this study elucidates the mechanical mechanisms of overburden grouting reinforcement at the particle scale and provides theoretical support for visual evaluation of concealed structures and optimization of grouting design. Full article

The mesoscopic-scale discrete element method (DEM) modeling approach demonstrated high compatibility with macroporous recycled concrete (MRC). However, existing DEM models failed to adequately balance modeling accuracy and computational efficiency for recycled aggregate (RA), replicate the three distinct interfacial transition zone (ITZ) types and pore structure of MRC, or establish a systematic calibration methodology. In this study, PFC 3D was employed to establish a randomly polyhedral RA composite model and an MRC model. A systematic methodology for parameter testing and calibration was proposed, and compressive test simulations were conducted on the MRC model. The model incorporated all components of MRC, including three types of ITZs, achieving an aggregate volume fraction of 57.7%. Errors in simulating compressive strength and elastic modulus were 3.8% and 18.2%, respectively. Compared to conventional concrete, MRC exhibits larger strain and a steeper post-peak descending portion in stress–strain curves. At peak stress, stress is concentrated in the central region and the surrounding arc-shaped zones. After peak stress, significant localized residual stress persists within specimens; both toughness and toughness retention capacity increase with rising porosity and declining compressive strength. Failure of MRC is dominated by tension rather than shear, with critical bonds determining strength accounting for only 1.4% of the total. The influence ranking of components on compressive strength is as follows: ITZ (new paste–old paste) > ITZ (new paste–natural aggregates) > new paste > old paste > ITZ (old paste–natural aggregates). The Poisson’s ratio of MRC (0.12–0.17) demonstrates a negative correlation with porosity. Predictive formulas for peak strain and elastic modulus of MRC were established, with errors of 2.6% and 3.9%, respectively. Full article

Calcium microcapsules were developed by spray-drying using mannoproteins (MPs) extracted from brewer’s spent yeast, xanthan gum (XG), and maltodextrin as encapsulating materials. The formulas included 11 g of calcium, 24 g of MP, and 0, 2, 4, or 8 g of XG 100 g⁻¹ solids, obtaining C1, C2, C3, and C4 microcapsules, respectively. Maltodextrin was added to complete 100 g of solids. Calcium intestinal (IB), colonic (CB), and total bioaccessibility (TB) were estimated after a simulated gastrointestinal digestion followed by in vitro colonic fermentation. The macromolecules of microcapsules interacted by ionic and hydrophobic forces. Microcapsules C1 and C2 showed a spherical shape. However, the addition of XG to the formulation contributed to the formation of concavities in the microcapsules. All microcapsules had higher IB than the control (CaCl₂), probably due to the calcium-chelating peptides dialyzed from MP. Moreover, C1 and C2 showed the highest IB values (≈23%). However, C3 and C4 showed the highest CB values (≈11%), attributing this effect to the short-chain fatty acids produced during colonic fermentation. Finally, C1 and C2 showed the highest TB (31.8 ± 0.1 and 32.0 ± 0.4%, respectively). The use of MP allowed for obtaining a supplement with high calcium bioaccessibility. Full article

Research on ecosystem carbon sequestration services and ecological compensation is crucial for advancing carbon neutrality. As a public good, ecosystem carbon sequestration services inherently lead to externalities. Therefore, it is essential to consider externalities in the flow of sequestration services. However, few studies have examined intra- and inter-regional ecosystem carbon sequestration flows, making regional ecosystem carbon sequestration flows less comprehensive. Against this background, the research objectives of this paper are as follows. The flow of carbon sequestration services between Henan Province and out-of-province regions is studied. In addition, this study clarifies the beneficiary and supply areas of carbon sink services in Henan Province and the neighboring regions at the prefecture-level city scale to obtain a more systematic, comprehensive, and actual flow of carbon sequestration services for scientific and effective eco-compensation and to promote regional synergistic emission reductions. The research methodologies used in this paper are as follows. First, this study adopts a meta-coupling framework, designating Henan Province as the focal system, the Central Urban Agglomeration as the adjacent system, and eight surrounding provinces as remote systems. Regional carbon sequestration was assessed using net primary productivity (NEP), while carbon emissions were evaluated based on per capita carbon emissions and population density. A carbon balance analysis integrated carbon sequestration and emissions. Hotspot analysis identified areas of carbon sequestration service supply and associated benefits. Ecological radiation force formulas were used to quantify service flows, and compensation values were estimated considering the government’s payment capacity and willingness. A three-dimensional evaluation system—incorporating technology, talent, and fiscal capacity—was developed to propose a diversified ecological compensation scheme by comparing supply and beneficiary areas. By modeling the ecosystem carbon sequestration service flow, the main results of this paper are as follows: (1) Within Henan Province, Luoyang and Nanyang provided 521,300 tons and 515,600 tons of carbon sinks to eight cities (e.g., Jiaozuo, Zhengzhou, and Kaifeng), warranting an ecological compensation of CNY 262.817 million and CNY 263.259 million, respectively. (2) Henan exported 3.0739 million tons of carbon sinks to external provinces, corresponding to a compensation value of CNY 1756.079 million. Conversely, regions such as Changzhi, Xiangyang, and Jinzhong contributed 657,200 tons of carbon sinks to Henan, requiring a compensation of CNY 189.921 million. (3) Henan thus achieved a net ecological compensation of CNY 1566.158 million through carbon sink flows. (4) In addition to monetary compensation, beneficiary areas may also contribute through technology transfer, financial investment, and talent support. The findings support the following conclusions: (1) it is necessary to consider the externalities of ecosystem services, and (2) the meta-coupling framework enables a comprehensive assessment of carbon sequestration service flows, providing actionable insights for improving ecosystem governance in Henan Province and comparable regions. Full article

To explore the dyeing technique and karyotype analysis of winter turnip rape (Brassica rape L.), the root tip of winter turnip rape Longyou 7 was used as the experimental material. Chromosome preparation technology was optimized, and karyotype analysis was carried out by changing the conditions of material collection time, pretreatment, fixation, and dissociation. The results showed that the optimal conditions for the preparation of dyeing winter turnip rape were as follows: the sampling time was 8:00–10:00, the ice–water mixture was pretreated at 4 °C for 20 h, the Carnot’s fixative solution I and 4 °C were fixed for 12 h, and the 1 mol/L HCl solution was bathed in a water bath at 60 °C for 10~15 min. Karyotype analysis showed that the number of chromosomes in winter turnip rape cells was 2n = 20, and the karyotype analysis formula was 2n = 2x = 20 = 16m + 4sm. The karyotype asymmetry coefficient was 58.85%, and the karyotype type belonged to type 2A, which may belong to the primitive type in terms of evolution. The results of this study provide a theoretical basis for further in-depth study of the phylogenetic evolution and genetic trend of Brassica rapa. Full article