Search Results (142)

This study investigates the influence of rear setback geometry and façade design parameters on microclimatic conditions, indoor thermal comfort, and energy performance in multi-story residential buildings in hot arid climates, addressing the growing need for climate-responsive design in regions with extreme temperatures and high solar radiation. Despite increasing interest in sustainable strategies, the combined effects of urban geometry and building envelope design remain underexplored in these environments. A coupled simulation framework was developed, integrating ENVI-met for outdoor microclimate modeling with Design Builder and EnergyPlus for dynamic building performance analysis. A total of 270 simulation scenarios were examined, combining three rear setback aspect ratios (1.5, 1.87, and 2.25), three window-to-wall ratios (10%, 20%, and 30%), three glazing types (single-, double-, and triple-pane), and two wall insulation states, using customized weather files derived from microclimate simulations. Global sensitivity analysis using rank regression and multivariate adaptive regression splines identified the glazing type as the most influential parameter (sensitivity index ≈ 0.99), especially for upper floors. At the same time, higher aspect ratios reduced peak Physiological Equivalent Temperature (PET) by up to 5 °C and decreased upper-floor cooling loads by 37%, albeit with a 9.3% increase in ground-floor cooling demand. Larger window-to-wall ratios lowered lighting energy consumption by up to 35% but had minimal impact on cooling loads, whereas wall insulation reduced annual cooling demand by up to 29,441 kWh. The results emphasize that integrating urban morphology with optimized façade components, particularly high-performance glazing and suitable aspect ratios, can significantly improve thermal comfort and reduce cooling energy consumption in hot arid residential contexts. Full article

Sea breezes alleviate coastal heat stress via cooling and humidifying. Sendai, Japan, in 2015 had a population of 1.08 million and an area of 786 km². Integrating the WRF model with RayMan, this study employs the PET index to assess spatiotemporal distributions of thermal comfort and heat stress, and their influencing factors, on typical summer sea-breeze days in Sendai, Japan. Results indicate that in the coastal zone, PET was primarily regulated by air temperature (Ta) and relative humidity (RH). In contrast, wind speed was the dominant influence on urban/inland zones, with Ta and RH contributing more during the evening. Sea breezes markedly improved the thermal environment in the coastal zone, suppressing PET increases. PET in urban and inland zones exhibited an initial rise followed by a decline, with the inland zone experiencing sustained extreme heat stress for 3 h. Among regions experiencing extreme heat stress, inland zones showed the highest proportion (17.75%), while coastal zones had the lowest (2.14%). Proportions across the three zones were similar under nighttime conditions with no thermal stress, with the urban zone exhibiting a slightly lower proportion. This study provides a theoretical basis for climate-adaptive urban planning leveraging sea breezes as a resource. Full article

Extreme high-temperature environments pose challenges for human thermal comfort and safety. This study introduces a compact portable liquid cooling garment weighing 3.6 kg in total with an integrated 1.99 kg vapor compression refrigeration unit (172 mm × 80 mm × 130 mm). This system innovatively integrates a patented evaporator-pump module and an optimized miniature rotary compressor, achieving a 151 W cooling capacity at 55 °C ambient temperature, surpassing existing portable systems in compactness and performance. Human trials with eight male participants at 35 °C (walking) and 40 °C (sitting) demonstrated that the liquid cooling garment system significantly improved thermal comfort. The mean thermal comfort vote decreased from 2.63 (uncomfortable) to 1.13 (slightly uncomfortable) while walking and from 3.88 (very uncomfortable) to 1.25 (slightly uncomfortable) while sitting. The mean skin temperature in the final stable state was reduced by 0.34 °C in walking trials and 1.09 °C in sitting trials, and heart rate decreased by up to 10.2 bpm in sedentary conditions. Comprehensive human trials under extreme heat further validate this system’s efficacy. This lightweight, efficient system offers a practical solution for personal thermal management in extreme high-temperature environments, with potential applications in industrial safety, military operations, and emergency response. Full article

The urban heat island (UHI) effect has emerged as a growing ecological challenge in compact urban environments. Although urban vegetation plays a vital role in mitigating thermal extremes, its cooling performance varies depending on vegetation type and urban morphological context. This study explores the extent to which compact urban development—quantified using the Mixed-use and Intensive Development (MIXD) index—modulates the cooling responses of different vegetation types in Nanjing, China. A combination of landscape metrics, regression-based interaction models, and XGBoost with SHAP analysis is employed to uncover vegetation-specific and structure-sensitive cooling effects. The results indicate that densely planted trees exhibit reduced cooling effectiveness in compact areas, where spatial clustering and fragmentation tend to intensify UHI effects, particularly during nighttime. In contrast, scattered trees are found to maintain more stable cooling performance across varying degrees of urban compactness, while low-lying vegetation demonstrates limited thermal regulation capacity. Critical thresholds of MIXD (approximately 28 for UHI area and 37 for UHI intensity) are identified, indicating a nonlinear modulation of green space performance. These findings underscore the importance of vegetation structure and spatial configuration in shaping urban microclimates and offer mechanistic insights into plant–environment interactions under conditions of increasing urban density. Full article

Introduction: Extrinsic skin damage is often a result of oxidative stress caused by exposure to environmental factors such as ultraviolet (UV) radiation, ozone (O₃), and various pollutants. As a result, topical antioxidants have been evaluated for their effectiveness in mitigating or reversing skin damage caused by environmental factors. Topical antioxidants containing a combination of l-ascorbic acid, tocopherol, and ferulic acid have significantly improved markers of skin health after exposure to environment-induced skin damage. However, research suggests that l-ascorbic acid and tocopherol tend to be relatively unstable, possibly affecting their efficacy against outdoor stressor damage. It has been shown that ferulic acid significantly improves the stability of both l-ascorbic acid and tocopherol, but its long-term stabilization effects on these antioxidants are relatively unknown. Material and Methods: This study evaluated the time-dependent effectiveness of a topical antioxidant mix containing 15% l-ascorbic acid, 1% tocopherol, and 0.5% ferulic acid (AOX) on UV-induced skin damage. Skin biopsies (12 mm, n = 60) were placed in a 6-well plate with medium and incubated at 37 °C and 5% CO₂ overnight. The day after, skin samples were pretreated with 10 µL of differently aged AOX (0-, 6-, 12-, and 36-month-old) and then exposed to different doses of UV light (100, 200, 400 mJ/cm²) daily over four days. AOX formulations were stored in a cool, dry, and dark place at approximately 20–22 °C during the whole study. This study evaluated 4-hydroxynonenal (4-HNE) and 8-hydroxy-2′-deoxyguanosine (8-OHdG) as oxidative damage and skin DNA damage markers, Collagen1 and Filaggrin as skin structure, and IL-8 and Nrf2 as inflammatory and defensive response. Results: UV exposure significantly increased oxidative and inflammatory markers in human skin explants affecting also filaggrin and collagen levels. However, pre-treatment with the antioxidant formulation, particularly in its younger formulations (0-, 6-, and 12-month-old), significantly reduced the damaging effect of UV. Additionally, all antioxidant formulations effectively mitigated UV-induced damage across all doses. Conclusions: Our results indicate that pre-treatment with this formulation consistently reduces UV-induced oxidative damage and DNA damage in human skin explants, regardless of the formulation age and the discoloration state. Although effective, the protective capacity of aged formulations may be reduced only when extreme UV exposure is tested, a condition that is unlikely to occur under typical environmental conditions. These results support ferulic acid as a stabilization agent for topical antioxidant mixtures. Full article

Improving outdoor thermal comfort is a critical objective in urban design, particularly in densely built urban environments. Elevated semi-open spaces—outdoor areas located beneath raised building structures—have been recognized for enhancing pedestrian comfort by improving airflow and shading. However, previous studies primarily focused on warm or temperate climates, leaving a significant research gap regarding their thermal performance in cold climate zones characterized by extreme seasonal variations. Specifically, few studies have investigated how these spaces perform under conditions typical of northern Chinese cities like Xi’an, which is explicitly classified within the Cold Climate Zone according to China’s national standard GB 50176-2016 and experiences both severe summer heat and cold winter conditions. To address this gap, we conducted field measurements and numerical simulations using the ENVI-met model (v5.0) to systematically evaluate the microclimatic performance of elevated ground-floor spaces in Xi’an. Key microclimatic parameters—including air temperature, mean radiant temperature, relative humidity, and wind velocity—were assessed during representative summer and winter conditions. Our findings indicate that the height of the elevated structure significantly affects outdoor thermal comfort, identifying an optimal elevated height range of 3.6–4.3 m to effectively balance summer cooling and winter sheltering needs. These results provide valuable design guidance for architects and planners aiming to enhance outdoor thermal environments in cold climate regions facing distinct seasonal extremes. Full article

The process of urbanization has intensified the urban heat environment, with the degradation of thermal conditions closely linked to the morphological characteristics of different functional zones. This study delineated urban functional areas using a multivariate dataset and investigated the seasonal and threshold effects of landscape and architectural features on land surface temperature (LST) through boosted regression tree (BRT) modeling and Spearman correlation analysis. The key findings are as follows: (1) LST exhibits significant seasonal variation, with the strongest urban heat island effect occurring in summer, particularly within industry, business, and public service zones; residence zones experience the greatest temperature fluctuations, with a seasonal difference of 24.71 °C between spring and summer and a peak temperature of 50.18 °C in summer. (2) Fractional vegetation cover (FVC) consistently demonstrates the most pronounced cooling effect across all zones and seasons. Landscape indicators generally dominate the regulation of LST, with their relative contribution exceeding 45% in green land zones. (3) Population density (PD) exerts a significant, seasonally dependent dual effect on LST, where strategic population distribution can effectively mitigate extreme heat events. (4) Mean building height (MBH) plays a vital role in temperature regulation, showing a marked cooling influence particularly in residence and business zones. Both the perimeter-to-area ratio (LSI) and frontal area index (FAI) exhibit distinct seasonal variations in their impacts on LST. (5) This study establishes specific indicator thresholds to optimize thermal comfort across five functional zones; for instance, FVC should exceed 13% in spring and 31.6% in summer in residence zones to enhance comfort, while maintaining MBH above 24 m further aids temperature regulation. These findings offer a scientific foundation for mitigating urban heat waves and advancing sustainable urban development. Full article

This study assessed the effectiveness of stress-based cognitive-behavioral training compared to standard training in firefighters, emphasizing their ability to distribute extinguishing water and cool environments evenly during enclosure fires. Experiments took place at the Zbiroh training facility with two firefighter teams (Team A with stress-based training and Team B with standard training) under realistic conditions. Using 58 thermocouples and 4 radiometers, temperature distribution and radiant heat flux were measured to evaluate water distribution efficiency and cooling performance during interventions. Team A consistently achieved temperature reductions of approximately 320 °C in the upper layers and 250–400 °C in the middle layers, maintaining stable conditions, whereas Team B only achieved partial cooling, with upper-layer temperatures remaining at 750–800 °C. Additionally, Team A recorded lower radiant heat flux densities (e.g., 20.74 kW/m² at 0°) compared to Team B (21.81 kW/m²), indicating more effective water application and adaptability. The findings confirm that stress-based training enhances firefighters’ operational readiness and their ability to distribute water effectively during interventions. This skill is essential for safer and effective management of indoor fires under extreme conditions. This study supports the inclusion of stress-based and scenario-based training in firefighter education to enhance safety and operational performance. Full article

Transpiration cooling that utilizes the phase change of a liquid coolant is recognized as an effective thermal protection technique for extreme environments. However, the introduction of phase change within the porous structure brings about challenges, such as vapor blockage, pressure fluctuations, and temperature inversion, which critically influence system reliability. This study conducts numerical analyses of coupled processes of heat transfer, flow, and phase change in transpiration cooling using a Two-Phase Mixture Model. The simulation incorporates a Local Thermal Non-Equilibrium approach to capture the distinct temperature fields of the solid and fluid phases, enabling accurate prediction of the thermal response within two-phase and single-phase regions. The results reveal that under low heat flux, dominant capillary action suppresses dry-out and expands the two-phase region. Conversely, high heat flux causes vaporization to overwhelm the capillary supply, forming a superheated vapor layer and constricting the two-phase zone. The analysis also explains a paradoxical pressure drop, where an initial increase in flow rate reduces pressure loss by suppressing the high-viscosity vapor phase. Furthermore, a local temperature inversion, where the fluid becomes hotter than the solid matrix, is identified and attributed to vapor counterflow and its subsequent condensation. Full article

Improving photovoltaic (PV) panel performance under extreme climatic conditions is critical for advancing sustainable energy systems. In hyper-arid regions, elevated operating temperatures significantly reduce panel efficiency. This study investigates and compares three cooling techniques—air cooling, water cooling, and porous media cooling—using thermal and electrical modeling based on CFD simulations in ANSYS. The numerical model replicates a PV system operating under peak solar irradiance (900 W/m²) and realistic ambient conditions in Adrar, Algeria. Simulation results show that air cooling leads to a modest temperature reduction of 6 °C and a marginal efficiency gain of 0.25%. Water cooling, employing a top-down laminar flow, reduces cell temperature by over 35 °C and improves net electrical output by 30.9%, despite pump energy consumption. Porous media cooling, leveraging passive evaporation through gravel, decreases panel temperature by around 30 °C and achieves a net output gain of 26.3%. Mesh sensitivity and validation against experimental data support the accuracy of the model. These findings highlight the significant potential of water and porous material cooling strategies to enhance PV performance in hyper-arid environments. The study also demonstrates that porous media can deliver high thermal effectiveness with minimal energy input, making it a suitable low-cost option for off-grid applications. Future work will integrate long-term climate data, real diffuser geometries, and experimental validation to further refine these models. Full article

This study compares high-frequency mobile observation data collected in the same area of Kunming under two different meteorological conditions—15 January 2020, and 8 January 2023—to analyze changes in the micro-scale urban thermal environment. Vehicle-mounted temperature and humidity sensors, combined with GPS tracking, were used to conduct real-time, high-resolution data collection across various urban functional areas. The results show that in the two tests, the maximum temperature differences were 10.4 °C and 16.5 °C, respectively, and the maximum standard deviations were 0.34 °C and 2.43 °C, indicating a significant intensification in thermal fluctuations. Industrial and commercial zones experienced the most pronounced cooling, while green spaces and water bodies exhibited greater thermal stability. The study reveals the sensitivity of densely built-up areas to cold extremes and highlights the important role of green infrastructure in mitigating urban thermal instability. Furthermore, this research demonstrates the advantages of mobile observation over conventional remote sensing methods in capturing fine-scale, dynamic thermal distributions, offering valuable insights for climate-resilient urban planning. Full article

Advancements in thermoregulating textiles have been propelled by innovations in nanotechnology, composite materials, and smart fiber engineering. This article reviews recent scholarly papers on experimental passive and active thermoregulating textiles to present the latest advancements in these fabrics, their mechanisms of thermoregulation, and their feasibility for use. The review underscores that phase-change materials enhanced with graphene, boron nitride, and carbon nanofibers offer superior thermal conductivity, phase stability, and flexibility, making them ideal for wearable applications. Shape-stabilized phase-change materials and aerogel-infused fibers have shown promising results in outdoor, industrial, and emergency settings due to their durability and high insulation efficiency. Radiative cooling textiles, engineered with hierarchical nanostructures and Janus wettability, demonstrate passive temperature regulation through selective solar reflection and infrared emission, achieving substantial cooling effects without external energy input. Thermo-responsive, shape-memory materials, and moisture-sensitive polymers enable dynamic insulation and actuation. Liquid-cooling garments and thermoelectric hybrids deliver precise temperature control but face challenges in portability and power consumption. While thermoregulating textiles show promise, the main challenges include achieving scalable manufacturing, ensuring material flexibility, and integrating multiple functions without sacrificing comfort. Future research should focus on hybrid systems combining passive and active mechanisms, user-centric wearability studies, and cost-effective fabrication methods. These innovations hold significant potential for applications in extreme environments, athletic wear, military uniforms, and smart clothing, contributing to energy efficiency, health, and comfort in a warming climate. Full article

In response to the performance requirements of ship conductive rings in the coupled environment of high salt spray, high humidity, and mechanical wear in the ocean, a Cu-TiC composite coating was prepared on the surface of 7075 aluminum alloy by using the high-speed laser cladding (HLC) technology. The influence laws of the scanning speed (86.4–149.7 mm/s) on the microstructure, tribological properties, and corrosion resistance of the coating were explored. The results show that the scanning speed significantly changes the phase composition and grain morphology of the coating by regulating the thermodynamic behavior of the molten pool. At a low scanning speed (86.4 mm/s), the CuAl₂ phase is dominant, and the grains are mainly columnar crystals. As the scanning speed increases to 149.7 mm/s, the accelerated cooling rate promotes an increase in the proportion of Cu₂Al₃ phase, refines the grains to a coexisting structure of equiaxed crystals and cellular crystals, and improves the uniformity of TiC particle distribution. Tribological property analysis shows that the high scanning speed (149.7 mm/s) coating has a 17.9% lower wear rate than the substrate due to grain refinement and TiC interface strengthening. The wear mechanism is mainly abrasive wear and adhesive wear, accompanied by slight oxidative wear. Electrochemical tests show that the corrosion current density of the high-speed cladding coating is as low as 7.36 × 10⁻⁷ A·cm⁻², and the polarization resistance reaches 23,813 Ω·cm². The improvement in corrosion resistance is attributed to the formation of a dense passivation film and the blocking of the Cl diffusion path. The coating with a scanning speed of 149.7 mm/s exhibits optimal wear-resistant and corrosion-resistant synergistic performance and is suitable for the surface strengthening of conductive rings in extreme marine environments. This research provides theoretical support for the process performance regulation and engineering application of copper-based composite coatings. Full article

The intensification of extreme temperature events driven by climate change has heightened the vulnerability of urban areas to heatwaves, making it a critical environmental challenge. In this study, we investigate the spatial characteristics of urban heatwave vulnerability in Jungang-dong, Gangneung—a representative mid-sized coastal city in South Korea that experiences a strong urban heat island (UHI) effect due to the prevalent land–sea breeze dynamics, high building density, and low green-space ratio. A representative heatwave day (22 August 2024) was selected using AWS data from the Korea Meteorological Administration (KMA), and hourly meteorological conditions were applied to Computational Fluid Dynamics (CFD) simulations to model the urban microclimates. The thermal stress levels were quantitatively assessed using the Universal Thermal Climate Index (UTCI). The results indicated that, at 13:00, the surface temperatures reached 40 °C and the UTCI values peaked at 43 °C, corresponding to a “Very Strong Heat Stress” level. Approximately 17.4% of the study area was identified as being under extreme thermal stress, particularly in densely built-up zones, roadside corridors with high traffic, and pedestrian commercial areas. Based on these findings, we present spatial analysis results that reflect urban morphological characteristics to guide the optimal allocation of urban cooling strategies, including green (e.g., street trees, urban parks, and vegetated roofs), smart, and engineered infrastructure. These insights are expected to provide a practical foundation for climate adaptation planning and thermal environment improvement in mid-sized urban contexts. Full article

Heat pipes are highly efficient heat transfer devices relying on phase-change mechanisms, with performance heavily influenced by working fluids and operational dynamics. This review article comprehensively examines hydrodynamics and heat transfer in heat pipes, contrasting conventional working fluids with nanofluid-enhanced systems. In the present work we discuss mathematical models governing fluid flow and heat transfer, emphasizing continuum and porous media approaches for wick structures. Functional dependencies of thermophysical properties (e.g., viscosity, surface tension, thermal conductivity) are reviewed, highlighting temperature-driven correlations and nanofluid modifications. Transport mechanisms within wicks are analyzed, addressing capillary-driven flow, permeability, and challenges posed by nanoparticle integration. Fourth, interfacial phase-change conditions—evaporation and condensation—are modeled, focusing on kinetic theory and empirical correlations. Also, numerical and experimental results are synthesized to quantify performance enhancements from nanofluids, including thermal resistance reduction and capillary limit extension, while addressing inconsistencies in stability and pressure drop trade-offs. Finally, applications spanning electronics cooling, aero-space, and renewable energy systems are evaluated, underscoring nanofluids’ potential to expand heat pipe usability in extreme environments. The review identifies critical gaps, such as long-term nanoparticle stability and scalability of lab-scale models, while advocating for unified frameworks to optimize nanofluid selection and wick design. This work serves as a foundational reference for researchers and engineers aiming to advance heat pipe technology through nanofluid integration, balancing theoretical rigor with practical feasibility. Full article