Search Results (171)

Scandate cathodes have garnered significant attention for their exceptional low-temperature, high-current-density emission characteristics. However, their widespread deployment in vacuum electronic devices is currently hindered by stringent vacuum requirements and susceptibility to ion bombardment. To enhance the engineering applicability of scandate cathodes, this study employs first-principles density functional theory (DFT) to model the surface microstructures of strontium (Sr)–scandium (Sc) co-doped systems. Guided by simulation predictions regarding surface elemental ratios, corresponding emission active materials and cathode samples were fabricated. A systematic comparison between theoretical calculations and experimental measurements reveals a critical trade-off: while increasing Sr content enhances structural stability (indicated by lower formation energies), it concurrently increases the work function. Consequently, an optimal Sr doping level of approximately 2 wt% is identified, which significantly improves emission current density without compromising stability. Cathodes fabricated with this optimized composition were tested in a practical electron gun configuration. Results demonstrate that under low-temperature conditions (1000 °C) and wide-pulse operation (2 ms), the cathode achieves an emission current density of 21.57 A/cm². These findings validate the efficacy of simulation-guided material design and highlight the potential of Sr-doped scandate cathodes for high-power microwave applications. Full article

Shooting activities offer educational and recreational value; however, their application in school physical education and recreational settings remains limited due to safety concerns, high costs, and restricted access to specialized facilities and equipment. To address these constraints, this study designed and implemented a low-cost laser shooting system suitable for school physical education and recreational use. The proposed system comprises a laser-gun module, a physical electronic target providing immediate on-site feedback using an illuminance sensor, a Fresnel lens, and RGB LEDs, and a web-based electronic target that enables real-time scoring, logging, and visualization via smartphone or tablet cameras and browser-based processing. By adopting a low-power, projectile-free laser structure with pulse-limited emission, the system enhances operational safety, while the use of general-purpose components and web standards reduces cost and lowers barriers to adoption. Technical verification conducted under controlled indoor conditions demonstrated stable single-shot operation, reliable hit detection, and accurate score calculation for both the physical and web-based targets. Expert validation involving specialists in physical education, educational technology, and sports technology yielded consistently high evaluations across safety, cost efficiency, functional completeness, and field applicability. These findings suggest that the proposed system represents a practical and scalable alternative for school physical education classes and recreational programs. Future research should examine user-level usability, learning outcomes, system robustness under diverse environmental conditions, and structured expert consensus processes. Full article

Yersinia enterocolitica is a foodborne pathogen that forms biofilms on surfaces, enhancing its survivability and increasing bacterial resistance, which poses a significant challenge to public health. Therefore, developing effective strategies to inhibit biofilm formation is crucial. Lipoic acid (LA) is a compound with antibiofilm properties. This study investigates the effects of LA on biofilm formation by Y. enterocolitica BNCC 108930 (a standard strain from the BeNa Culture Collection). Biofilm formation, maturation, removal, and cell viability were evaluated by crystal violet staining, extracellular polysaccharide assay, Methylthiazolyldiphenyl-tetrazolium bromide assays, motility, and quorum sensing (QS) assays. The results indicate that LA interferes with the early stages of biofilm formation by compromising cell membrane integrity and reducing cellular adhesion. Furthermore, 2.5 mg/mL of LA reduced biofilm biomass (with a 48 h treatment inhibition rate of 51.46 ± 1.29%) and extracellular polysaccharide production (with a relative inhibition rate of 30.09 ± 1.8%), while significantly reducing the metabolic activity of bacteria within the biofilm (inhibition rate over 85%) compared to the untreated group. Confocal laser scanning microscopy and field emission gun scanning electron microscopy confirm that LA induces a sparse biofilm structure, reduced aggregation, and decreased biofilm thickness to 21.33 ± 2.27 μm. Motility and QS assays demonstrate that LA affects flagellar motility and the secretion of N-acyl homoserine lactones. Transcriptome analysis revealed downregulation of genes involved in the QS system and biofilm formation (e.g., lsrA, lsrC, lsrD, lsrR, and oppA), as well as upregulation of genes related to bacterial chemotaxis and flagellar assembly (e.g., RS19655, RS15590, fliE, fliJ, fliP, fliA, and fliK). These alterations suggest that LA inhibits Y. enterocolitica biofilm formation by affecting intercellular communication and flagellar motility. This study highlights the antibiofilm properties of LA, providing a theoretical basis for potential applications in microbial and biofilm control. Full article

The influence of electron beam treatment parameters (electron gun speed, electron beam current, scanning frequency, and sweep type) on the structure and properties of the surface layer of the composite material AlMg3-5SiC has been investigated. Composite specimens of AlMg₃ alloy reinforced with 5 wt.% silicon carbide particles were manufactured via the stir casting process. Experimentally, processing modes with heat input from 120 to 240 J/mm yield a modified layer thickness from 74 to 1705 µm. Heat input should not exceed 150 J/mm to ensure a smooth and defect-free surface layer. The macro- and microstructure were examined using optical microscopy. Brinell hardness was measured. Friction and wear tests were performed under dry sliding friction conditions using the “bushing on plate” scheme. This evaluated the tribological properties of the composite material in its original cast state and after modifying treatment. Due to the matrix alloy structure refinement by 5–10 times, the surface layer’s hardness increases by 11% after treatment. The modified specimens have superior tribological properties to the initial ones. Wear rate reduces by 17.5%, the average friction coefficient reduces by 32%, and the root mean squared error of the friction coefficient, which measures friction process stability, reduces by 50% at a specific load of 2.5 MPa. Therefore, the electron beam treatment process is a useful method for producing high-quality and uniform wear-resistant aluminum matrix composite surface layers. Full article

The increasing threat posed by micrometeoroids and orbital debris to in-orbit spacecraft necessitates the development of lightweight and deformable shielding systems capable of withstanding hypervelocity impacts. Ultra-high-molecular-weight polyethylene (UHMWPE) films, owing to their high specific strength and energy-absorption capacity, present a promising candidate for such applications. However, the hypervelocity impact response of thin, highly oriented UHMWPE films—distinct from bulk plates or composites—remains poorly understood, particularly for micron-scale particles at velocities relevant to space debris (≥8 km/s). In this study, we systematically investigate the impact resistance of 0.1 mm UHMWPE films using a plasma-driven microparticle accelerator and a hypervelocity dust gun to simulate impacts by micron-sized Al₂O₃ and Fe particles at velocities up to ~8.5 km/s. Through detailed analysis of crater morphology via scanning electron microscopy, we identify three distinct damage modes: plastic-dominated craters (Type I), fracture-melting craters (Type II), and perforations (Type III). These modes are correlated with impact energy and particle size, revealing the material’s transition from large-scale plastic deformation to localized thermal softening and eventual penetration. Crucially, we provide quantitative penetration thresholds (e.g., 2.25 μm Al₂O₃ at 8.5 km/s) and establish a microstructure-informed damage classification that advances the fundamental understanding of UHMWPE film behavior under extreme strain rates. Our findings not only elucidate the energy-dissipation mechanisms in oriented polymer films but also offer practical guidelines for the design of next-generation, flexible spacecraft shielding systems. Full article

ZnO thin films were deposited on soda–lime glass substrates using the chemical spray pyrolysis method at a temperature of 500 °C. After the deposition, the substrates were irradiated with 10 keV H⁺ and Ar⁺ ions using a Colutron ion gun. We investigated the optical, structural, and morphological properties of the irradiated samples using Rutherford Backscattering Spectrometry, Ultraviolet and Visible Spectroscopy, X-ray diffraction, and Scanning Electron Microscopy. Our results showed a slight decrease in the optical band gap of the irradiated samples, which can be attributed to the quantum confinement effect caused by changes in the crystallite size. The diffractograms displayed diffraction peaks corresponding to the characteristic planes of the hexagonal wurtzite phase of ZnO, indicating that the films were polycrystalline with a preferential orientation along the c-axis. We also observed a reduction in the average crystallite size of the samples after ion irradiation. The morphological study showed that the average grain size increased and the shape changed from spherical in the pristine sample to flake-like after irradiation. Additionally, the samples irradiated with Ar⁺ ions exhibited a bimodal distribution in grain size, which is attributed to the defects and nucleation centers generated during the irradiation process. Full article

Field emission (FE) cold-cathodes have some important characteristics, including instant turn-on, room temperature operation, miniaturization, low power consumption, and nonlinearity. As emitters, Carbon nanotubes (CNTs) exhibit a high field enhancement factor, low turn-on voltage, high current density, high thermal conductivity, and temporal stability. These properties make them highly suitable for applications in FE cold-cathodes. In addition, Carbon nanotube (CNT) cold cathodes have specialized applications in electron beams, which are modulated by high-frequency electric fields and exhibit low energy dispersion. There have been substantial studies on CNT-based cold cathode electron guns with diverse structural configurations. These studies have laid the foundation for the applications of microwave vacuum electron devices, X-ray equipments, flat-panel displays, and scanning electron microscopes. The review primarily introduces cold cathode electron guns based on CNT emitters with diverse morphologies, including disordered CNTs, aligned CNTs, CNT paste, and other CNTs with special surface morphologies. Additionally, the research results of microwave electron guns based on CNT cathodes are also mentioned. Finally, the problems that need to be resolved in the practical applications of CNT cold cathode electron guns are summarized, and some suggestions for future development are provided. Full article

Marking techniques are employed to guarantee the identification and traceability of biomedical materials. This study investigated the impact of laser and mechanical marking processes on the tribological performance of ISO 5832-1 austenitic stainless steel (SS), specifically examining corrosion resistance, the coefficient of friction, and wear volume in ball-cratering wear tests. The laser marking was performed using a nanosecond Q-switched Nd:YAG laser. Cytotoxicity tests assessed the biocompatibility of the biomaterial. Non-marked surfaces were also evaluated for comparison. A phosphate-buffered saline solution (PBS) served as both the lubricant and corrosion medium. The surface finishing was analyzed using optical microscopy and scanning electron microscopy coupled with a field-emission gun (SEM-FEG), combined with an energy-dispersive X-ray spectrometer. The oxide film was examined through X-ray photoelectron spectroscopy (XPS). Wear tests lasted 10 min, with PBS drops applied every 10 s at 75 rpm; solid balls of AISI 316L stainless steel (SS) and polypropylene (PP), each 1 inch in diameter, were used as counter-bodies. Corrosion resistance was assessed using electrochemical methods. Results showed variations in roughness and microstructure due to laser marking. The tribological behaviour was influenced by the type of marking process, and the wear amount depended on the normal force and ball nature. None of the samples was considered cytotoxic, although laser-marked surfaces exhibited the lowest cellular viability among the tested surfaces and the lowest corrosion resistance. Full article

An electron optic system (EOS) consisting of a sheet electron beam gun (SEB) and a pole offset periodic cusped magnet (PO-PCM) is reported for 340-GHz frequency. A sheet electron beam with a voltage of 29 kV, beam compression ratio of 16, and a beam waist of size 0.17 mm × 0.044 mm was designed and optimized using computer simulation technology (CST). The EOS was capable of transmitting the beam with a current of 6.9 mA through a beam tunnel of size 0.516 mm × 0.091 mm, having a length of 60 mm with the help of a pole offset periodic cusped magnet. The axial magnetic field generated by the PCM was 0.32 T. The EOS was efficient enough to transmit the beam stably through the beam tunnel with a transmission rate of 100%. Full article

This paper serves as a comprehensive and practical resource to guide researchers in selecting suitable metals for use as photocathodes in radio-frequency (RF) and superconducting radio-frequency (SRF) electron guns. It offers an in-depth review of bulk and thin-film metals commonly employed in many applications. The investigation includes the photoemission, optical, chemical, mechanical, and physical properties of metallic materials used in photocathodes, with a particular focus on key performance parameters such as quantum efficiency, operational lifetime, chemical inertness, thermal emittance, response time, dark current, and work function. In addition to these primary attributes, this study examines essential parameters such as surface roughness, morphology, injector compatibility, manufacturing techniques, and the impact of chemical environmental factors on overall performance. The aim is to provide researchers with detailed insights to make well-informed decisions on materials and device selection. The holistic approach of this work associates, in tabular format, all photo-emissive, optical, mechanical, physical, and chemical properties of bulk and thin-film metallic photocathodes with experimental data, aspiring to provide unique tools for maximizing the effectiveness of laser cleaning treatment. Full article

High-current electron beams can significantly enhance the productivity of variety of applications including medical radioisotope (RI) production and wastewater purification. High-power superconducting radio frequency (SRF) linacs are capable of producing such high-current electron beams due to the key advantage to operate in continuous wave (CW) mode. However, this requires an injector capable of generating electron bunches with high repetition rate and in CW mode, while minimizing beam losses to avoid damage to SRF cavities due to quenching. RF gating to the grid of a thermionic electron gun is a promising solution, as it ensures CW bunch generation at the repetition rate same as the fundamental or sub-harmonics of the accelerating RF frequency, with minimal beam loss. This paper presents detailed beam dynamics simulations demonstrating that an RF-gated gun operating at 1.3 GHz can generate bunches with 148 ps full width with 8.96 pC charge. Full article

The Polish Free-Electron Laser (PolFEL), which is currently under construction in the National Centre for Nuclear Research in Świerk near Warsaw, will comprise an electron gun and from four to six cryomodules, each accommodating two nine-cell TESLA RF superconducting resonant cavities. To cool the superconducting resonant cavities, the cryomodules will be supplied with superfluid helium at a temperature of 2 K. Other requirements regarding the cooling power of PolFEL result from the need to cool the power couplers for the accelerating cryomodules (5 K) and thermal shields, which limit the heat inleaks due to radiation (40–80 K). The machine will utilize several thermodynamic states of helium, including two-phase superfluid helium, supercritical helium, and low-pressure helium vapours. Supercritical helium will be supplied from a cryoplant by a cryogenic distribution system (CDS)—transfer line and valve boxes—where it will be thermodynamically transformed into a superfluid state. This article presents the architecture of the CDS, discusses several design solutions that could have been decided on with the use of second law analysis, and presents the design methodology of the chosen CDS elements. Full article

Pressure drop processes, such as dissolved inorganic carbon and gun-puffing, have shown utility in the food industry, but their reliance on heat remains a limiting factor. This study involved the development of a processor capable of performing nonthermal pressure drop treatment, which minimizes thermal changes in food. In addition, its effects on the structure and soaking efficiency of adzuki beans were analyzed. Two improved pressure drop processes were tested: PDA, which applied 1 kgf/cm² of pressure before release, and PDB, which applied a higher pressure and gradually decreased it in steps of 1 kgf/cm². Both the PDA and PDB pretreatments enhanced soaking more effectively than heat treatments at 60 °C and 100 °C, whereas no significant effect was observed at 25 °C, indicating a minimal heat requirement for moisture and gas release. Notably, repeated PDB application (more than 40 times) further increased the moisture absorption without thermal influence. Scanning electron microscopy revealed that the PDA, PDB, and heat treatments caused cracks in the hilum region and increased surface wrinkling and mesh structure deformation. These findings demonstrate the potential of pressure drop treatment to improve soaking efficiency through structural modification, supporting its use as an effective nonthermal pretreatment method. Full article

Linear conjugated polymer photocatalysts are still hampered by challenges involving low charge separation efficiency and poor water dispersibility, which are crucial factors during the photocatalytic water splitting process. Herein, we synthesized Poly thieno[3,2-b]thiophene (PTT) nanoparticles with excellent visible light response characteristic. Subsequently, we constructed the gun–bullet model PTT/graphitic carbon nitride (PTT/g-C₃N₄) heterojunctions for photocatalytic hydrogen production, where PTT with good visible light response characteristic serves as the bullets and g-C₃N₄ with good water dispersibility serves as the guns. The as-prepared PTT/g-C₃N₄ heterojunctions show greatly accelerated charge separation and excellent photocatalytic hydrogen production performance. Specifically, 10PTT/g-C₃N₄ demonstrates extraordinary hydrogen production performance, reaching 6.56 mmol g⁻¹ h⁻¹ (2 wt% Pt loading, 0.1 M AA as sacrificial agent, λ > 420 nm), calculated to be 15.3 and 22.6 times those of PTT and g-C₃N₄, respectively. Mechanistic studies reveal that the significantly improved performance of PTT/g-C₃N₄ heterojunctions is ascribed to the accelerated charge transfer, which originates from the C…S/N…S noncovalent interactions among PTT and g-C₃N₄. The C…S/N…S noncovalent interactions act as an efficient interface charge transmission channel (ICTC), accelerating the steady stream of excited electron transfer from the lowest unoccupied molecular orbital (LUMO) of PTT to that of g-C₃N₄. The gun–bullet model heterojunctions proposed here provide a practical strategy for achieving exceptional visible light photocatalytic hydrogen production by combining charge separation with water dispersibility in polymer/polymer heterojunctions via noncovalent interactions. Full article

We present a corrosion-resistant quadrupole ion trap mass spectrometer (QIT-MS) for the direct detection of biosignature gasses in chemically reactive planetary atmospheres, such as Venusian clouds. The system employs a Paul trap with hyperbolic titanium alloy electrodes and alumina spacers for chemical durability and precise ion confinement. An yttria-coated iridium filament serves as the thermionic emitter within a modular electron gun capable of axial and radial ionization. Analytes are introduced through fused silica capillaries and crescent inlets into a miniature pressure cell. The testbed integrates high-voltage RF electronics, pressure-regulated sample delivery, and FPGA-based control for real-time tuning. Continuous operation in 98% sulfuric acid vapor for over three months demonstrated no degradation in emitter or sensor performance. Mass spectra revealed H₂SO₄ fragmentation and thermally induced decomposition up to 425 K. Spectral variations with filament current and electron energy highlight thermal and electron-induced dissociation dynamics. Operational modes include high-resolution scans and selective ion ejection (e.g., CO₂⁺, N₂⁺) to enhance the detection of PH₃⁺, H₂S⁺, and daughter ions. The compact QIT-MS platform is validated for future missions targeting corrosive atmospheres, enabling in situ astrobiological investigations through the detection of biosignature gasses such as phosphine and hydrogen sulfide. Full article