Search Results (409)

Ultrahigh-temperature ceramic composites based on hafnium diboride have a wide range of applications, including as components for high-speed aircraft and energy generation and storage devices. Consequently, developing methodologies for their fabrication and studying their properties are of paramount importance, in particular in using them as an electrode material for energy storage devices with increased oxidation resistance. This study investigates the behavior of ceramic composites based on the HfB₂-HfO₂-SiC system, obtained using 15 vol% Ti₂AlC MAX-phase as a sintering component, under the influence of subsonic flow of dissociated air. It was determined that incorporating the modifying component (Ti₂AlC) altered the composition of the silicate melt formed on the surface during ceramic oxidation. This modification led to the observation of a protective antioxidant function. Consequently, liquation was observed in the silicate melt layer, resulting in the formation of spherical phase inhomogeneities in its volume with increased content of titanium, aluminum, and hafnium. It is hypothesized that the increase in the high-temperature viscosity of this melt prevents it from being carried away in the form of drops, even at a surface temperature of ~1900–2000 °C. Despite the established temperature, there is no sharp increase in its values above 2400–2500 °C. This is due to the evaporation of silicate melt from the surface. In addition, the electrochemical behavior of the obtained material in a liquid electrolyte medium (KOH, 3 mol/L) was examined, and it was shown that according to the value of electrical conductivity and specific capacitance, it is a promising electrode material for supercapacitors. Full article

The motivation for increasing the efficiency of renewable energy sources is the basic problem of ongoing research. Currently, intensive research is underway in technology based on the use of dye-sensitized solar cells (DSSCs). The aim of this work is to investigate the effect of modifying the iodide electrolyte with liquid crystals (LCs) known for the self-organization of molecules into specific mesophases. The current–voltage (I-V) and power–voltage (P-V) characteristics were determined for the ruthenium-based dyes N3, Z907, and N719 to investigate the influence of their structure and concentration on the efficiency of DSSCs. The addition of a nematic LC of 4-n-pentyl-4-cyanobiphenyl (5CB) to the iodide electrolyte influences the I-V and P-V characteristics. A modification of the I-V characteristics was found, especially a change in the values of short circuit current (I_SC) and open circuit voltage (V_OC). The conversion efficiency for cells with modified electrolyte shows a complex dependence that first increases and then decreases with increasing LC concentration. It may be caused by the orientational interaction of LC molecules with the titanium dioxide (TiO₂) layer on the photoanode. A too high concentration of LC may lead to a reduction in total ionic conductivity due to the insulating effect of the elongated polar molecules. Full article

Background/Objectives: Since breast cancer (BC) survival rates have increased to 91% at 5 years and 80% at 15 years postdiagnosis, there is a growing awareness of the importance of addressing the long-term well-being of patients. Consequently, integrative oncology, which combines standard therapies with complementary approaches (nutrition, mind–body practices, and lifestyle modifications), has emerged as a patient-centred model aimed at improving symptom management, treatment adherence, and overall quality of life (QoL). This study aims to demonstrate how integrative therapies can benefit body composition, phase angle, and fluid and electrolyte balance through bioelectrical impedance analysis (BIA). Methods: This study considers a patient who underwent BC surgery and was enrolled in the AMICO clinic for anamnesis, as well as their oncological pathology data, assessment of QoL, and BIA. The breast surgeon specialising in integrative oncology therapies prescribed the patient curcumin and polydatin, moderate physical activity, a balanced diet, and Qigong sessions. The patient underwent monitoring through haematochemical analysis, BIA, and a QoL questionnaire, with follow-up every four months. Results: Between 4 and 12 months, fat mass (FM) and body mass index (BMI) markedly decreased, whereas fat-free mass (FFM), total body water (TBW), and skeletal muscle mass (SMM) increased progressively. Moreover, the improvements in the Na/K ratio and phase angle (PhA) suggest a shift toward better electrolyte and fluid balance and enhanced cellular integrity and membrane function. Equally outstanding were her psychological benefits in terms of mood, sleep, anxiety, and melancholy. Conclusions: Patient progress in body composition, metabolic function, pain management, and psychological status measured during the 12-month follow-up demonstrates the potential benefits of an integrative approach to supportive cancer care. Full article

Introduction: The sodium-to-potassium (Na:K) ratio in the diet is a critical biomarker for cardiovascular and metabolic health, yet global adherence to recommended levels remains poor. Objectives: The objective of this study was to identify dietary determinants of the dietary Na:K ratio and its associations with micronutrient intake and diet quality. Methods: An observational cross-sectional survey was conducted in a representative sample of manufacturing workers through a combined stratified proportional and two-stage probability sampling plan, with strata defined by company size and industrial sector from the state of Rio Grande do Norte, Brazil. Dietary intake was assessed using 24 h recalls via the Multiple Pass Method, with Na:K ratios calculated from quantified food composition data. Diet quality was assessed with the Diet Quality Index-International (DQI-I). Multiple linear regression was used to analyze associations of Na:K ratio with the study variables. Results: The survey was conducted in the state of Rio Grande do Norte, Brazil, in 921 randomly selected manufacturing workers. The sample mean age was 38.2 ± 10.7 years, 55.9% males, mean BMI 27.2 ± 4.80 kg/m². The mean Na:K ratio was 1.97 ± 0.86, with only 0.54% of participants meeting the WHO recommended target (<0.57). Fast food (+3.29 mg/mg per serving, p < 0.001), rice, bread, and red meat significantly increased the ratio, while fruits (−0.16 mg/mg), dairy, white meat, and coffee were protective. Higher Na:K ratios were associated with lower intake of calcium, magnesium, phosphorus, and vitamins C, D, and E, as well as poorer diet quality (DQI-I score: −0.026 per 1 mg/mg increase, p < 0.001). Conclusions: These findings highlight the critical role of processed foods in elevating Na:K ratios and the potential for dietary modifications to improve both electrolyte balance and micronutrient adequacy in industrial workers. The study underscores the need for workplace interventions that simultaneously address sodium reduction, potassium enhancement, and overall diet quality improvement tailored to socioeconomic and cultural contexts, a triple approach not previously tested in intervention studies. Future studies should further investigate nutritional consequences of imbalanced Na:K intake. Full article

This study investigates the thermal response and surface modification of low-carbon manganese-alloyed 20GL steel during electrolytic plasma hardening. The objective was to evaluate the feasibility of surface hardening 20GL steel—traditionally considered difficult to quench—by combining high-rate surface heating with rapid cooling in an electrolyte medium. To achieve this, a transient two-dimensional heat conduction model was developed to simulate temperature evolution in the steel sample under three voltage regimes. The model accounted for dynamic thermal properties and non-linear boundary conditions, focusing on temperature gradients across the thickness. Experimental temperature measurements were obtained using a K-type thermocouple embedded at a depth of 2 mm, with corrections for sensor inertia based on exponential response behavior. A comparison between simulation and experiment was conducted, focusing on peak temperatures, heating and cooling rates, and the effective thermal penetration depth. Microhardness profiling and metallographic examination confirmed surface strengthening and structural refinement, which intensified with increasing voltage. Importantly, the study identified a critical cooling rate threshold of approximately 50 °C/s required to initiate martensitic transformation in 20GL steel. These findings provide a foundation for future optimization of quenching strategies for low-carbon steels by offering insight into the interplay between thermal fluxes, surface kinetics, and process parameters. Full article

This article explores the issue of surface modification through tumbling and vaporisation of 3D-printed materials, and its impact on the electrolytic deposition of metal coatings on previously non-conductive materials. Plastic materials represent an affordable alternative, but their surface treatment, in the form of post-coating, achieves properties comparable to those of metal parts while saving expensive metal material. Samples prepared by selective laser sintering (SLS) with different surface treatments were used. Polyamide 12 (PA12) was chosen as the base material and copper (Cu) as the metallic coating. Graphite was sprayed on the samples to ensure conductivity. The Cu coating was electrodeposited from an acidic copper electrolyte. The quantitative analysis of the surface was carried out using standard ISO parameters. The thickness of the deposited copper layer was determined using destructive measurements on a digital microscope. The results show that surface modification has a significant effect on the functional properties of the surface quality and the thickness of the deposited copper layer. Full article

The sustainable valorization of electrolytic manganese residue (EMR) and fly ash (FA) presents critical environmental challenges. This study systematically investigates the performance optimization of EMR-FA ceramic composites through the coordinated regulation of raw material ratios, sintering temperatures, and additive effects. While the composite with 85 g FA exhibits the highest mechanical strength, lowest porosity, and minimal water absorption, the formulation consisting of 45 wt% EMR, 40 wt% FA, and 15 wt% kaolin is identified as a balanced composition that achieves an effective compromise between mechanical performance and solid waste utilization efficiency. Sintering temperature studies revealed temperature-dependent property enhancement, with controlled sintering at 1150 °C preventing the over-firing phenomena observed at 1200 °C while promoting phase evolution. XRD-SEM analyses confirmed accelerated anorthite formation and the morphological transformations of FA spherical particles under thermal activation. Additive engineering demonstrated that 8 wt% CaO addition enhanced structural densification through hydrogrossular crystallization, whereas Na₂SiO₃ induced sodium-rich calcium silicate phases that suppressed anorthite development. Contrastingly, ZrO₂ facilitated zircon nucleation, while TiO₂ enabled progressive performance enhancement through amorphous phase modification. This work establishes fundamental phase–structure–property relationships and provides actionable engineering parameters for sustainable ceramic production from industrial solid wastes. Full article

Magnesium (Mg) alloys have demonstrated tremendous potential in biomedical applications, emerging as promising metallic biomaterials due to their biocompatibility, degradability, and favorable mechanical properties. However, their practical implementation faces significant limitations stemming from mechanical performance degradation and premature fracture failure caused by complex physiological interactions, including flow erosion, corrosion fatigue, stress coupling effects, and dynamic wear under bodily conditions. Surface coating technology has been recognized as an effective strategy to prevent direct contact between magnesium substrates and corrosive media. This review systematically examines the fundamental degradation mechanisms of magnesium alloys in both vivo and vitro environments, presents recent advances in surface modification coatings for magnesium alloys, and critically analyses the interaction mechanisms between modified layers and electrolyte solutions. Special emphasis is placed on revealing the formation mechanisms, structural characteristics, and fracture behaviors of conversion coatings. Furthermore, the study discusses the current challenges in biomedical surface modification of magnesium alloys, proposes potential solutions to enhance their clinical applicability, and outlines future research directions to fully exploit the development potential of these advanced biomaterials. Full article

Fish gelatin (FG) has garnered significant attention as an alternative to mammalian gelatin, primarily attributed to its distinct advantages. These include the absence of epidemic transmission risks and the lack of religious restrictions, making it a more universally acceptable and safer option. However, its application is limited due to shortcomings such as insufficient gel properties (such as rheological properties, gel strength, etc.). In this study, flaxseed gum (FFG) of 0–1.2% w/v was used to modify FG. The rheological properties, structural characteristics, and chemical bond changes of FG before and after modification were systematically analyzed using instruments such as a rheometer, infrared spectrometer, and Zeta potential analyzer. The results revealed that an appropriate amount of FFG could increase the gel strength of FG, but excessive FFG (>0.4%) reduced its gel strength. Moreover, FFG could increase the gelation transition temperature and apparent viscosity of the composite gel. FTIR confirmed that FFG and FG were bound through hydrogen bonding, β-sheet structure formation, and multi-electrolyte complexation. The ESEM showed that FFG promoted the formation of a denser network structure of FG. This study laid a theoretical foundation for the application and development of FG in the field of high-gel foods. Full article

The friction surfacing (FS) process has emerged over the past few years as a method for joining both similar and dissimilar materials, for volume damage repair of defective components, and for corrosion protection. The possibility to produce a metallic coating by FS, without melting the material, classifies this technique as distinct from other standard methods. This unconventional deposition method is based on the severe plastic deformation that appears on a rotating metallic rod (consumable material) pressed against the substrate under an axial load. The present study aims to investigate the tribological properties and corrosion resistance provided by the aluminum-based FS coatings deposited onto a structural S235 steel substrate and further modified by plasma electrolytic oxidation (PEO). During the PEO treatment, the formation of a ceramic film is enabled, while the hardness, chemical stability, corrosion, and wear resistance of the modified surfaces are considerably increased. The morpho-structural characteristics and chemical composition of the PEO-modified FS coatings are further investigated using scanning electron microscopy combined with energy dispersive spectroscopy analysis and X-ray diffraction. Dry sliding wear testing of the PEO-modified aluminum-based coatings was carried out using a ball-on-disc configuration, while the corrosion resistance was electrochemically evaluated in a 3.5 wt.% NaCl solution. The corrosion rates of the aluminum-based coatings decreased significantly when the PEO treatment was applied, while the wear rate was substantially reduced compared to the untreated aluminum-based coating and steel substrate, respectively. Full article

This study presents the development and comprehensive evaluation of magnesium-based implants with surface modifications using selected polymers and bioactive compounds. The implants were fabricated via plasma electrolytic oxidation (PEO), followed by the application of chitosan, polydopamine (PDA), and gold nanoparticles as bioactive surface coatings. In vitro experiments, including FT-IR spectroscopy, scanning electron microscopy (SEM), wettability tests, biodegradation assays in simulated body fluid (SBF), electrochemical corrosion analysis, and cytotoxicity tests using MG-63 osteoblast-like cells, were employed to assess the physicochemical and biological properties of the materials. The PEO + PDA-modified samples demonstrated the highest corrosion resistance (−1.15 V corrosion potential), enhanced cell viability (~95%), and favorable surface wettability (contact angle ~12.5°), outperforming other tested configurations. These findings suggest that PEO combined with PDA offers a synergistic effect, leading to superior biocompatibility and degradation control compared to unmodified magnesium or single-coating strategies. The developed implants hold promise for orthopedic applications requiring biodegradable, bioactive, and cytocompatible materials. Full article

Nickel-rich layered oxides such as LiNi_xMn_yCo_zO₂ (NMC), LiNi_xCo_yAl_zO₂ (NCA), and LiNi_xMn_yCo_zAl_{(1–x–y–z)}O₂ (NMCA), where x ≥ 0.6, have emerged as key cathode materials in lithium-ion batteries due to their high operating voltage and superior energy density. These materials, characterized by low cobalt content, offer a promising path toward sustainable and cost-effective energy storage solutions. However, their electrochemical performance remains below theoretical expectations, primarily due to challenges related to structural instability, limited thermal safety, and suboptimal cycle life. Intensive research efforts have been devoted to addressing these issues, resulting in substantial performance improvements and enabling the development of next-generation lithium-ion batteries with higher nickel content and reduced cobalt dependency. In this review, we present recent advances in material design and engineering strategies to overcome the problems limiting their electrochemical performance (cation mixing, phase stability, oxygen release, microcracks during cycling). These strategies include synthesis methods to optimize the morphology (size of the particles, core–shell and gradient structures), surface modifications of the Ni-rich particles, and doping. A detailed comparison between these strategies and the synergetic effects of their combination is presented. We also highlight the synergistic role of compatible lithium salts and electrolytes in achieving state-of-the-art nickel-rich lithium-ion batteries. Full article

Internal Dry Reforming of Methane (IDRM) in biogas fed Solid Oxide Fuel Cells (SOFCs) was investigated on Fe-Au modified Ni/GDC electrolyte-supported cells at 900 and 850 °C. The aim was to clarify the synergistic interaction between Fe and Au, focusing on the effect of X wt.% of Au loading (where X = 1 or 3 wt.%) in binary Au-Ni/GDC and ternary 0.5 wt.% Fe-Au-Ni/GDC fuel electrodes. The investigation combined i-V, Impedance Spectroscopy and Gas Chromatography electrocatalytic measurements. It was found that modification with 0.5Fe-Au enhanced significantly the electrocatalytic activity of Ni/GDC for the IDRM reaction, whereas the low wt.% Au content had the most promoting effect. The positive interaction of 0.5 wt.% Fe with 1 wt.% Au increased the conductivity of Ni/GDC and enhanced the corresponding IDRM charge transfer electrochemical processes, especially those in the intermediate frequency region. Comparative long-term measurements, between cells comprising Ni/GDC and 0.5Fe-1Au-Ni/GDC, highlighted the significantly higher IDRM electrocatalytic activity of the modified electrode. The latter operated for almost twice the time (280 h instead of 160 h for Ni/GDC) with a lower degradation rate (0.44 mV/h instead of 0.51 mV/h). Ni/GDC degradation was ascribed to inhibited charge transfer processes in the intermediate frequencies region and to deteriorated ohmic resistance. Stoichiometric analysis on the (post-mortem) surface state of each fuel electrode showed that the wt.% content of reduced nickel on Ni/GDC was lower, compared to 0.5Fe-1Au-Ni/GDC, verifying the lower re-oxidation degree of the latter. This was further correlated to the hindered H₂O production during IDRM operation, due to the lower selectivity of the modified electrode for the non-desired RWGS reaction. Full article

Estradiol is a natural estrogen belonging to the group of natural steroid hormones. This paper presents new electrochemical biosensors—simple and low-cost tools for the determination of β-estradiol. The receptor layer of the sensor is the enzyme laccase, which was immobilized on the substrate surface using the soft plasma polymerization technique. This technique is innovative and environmentally friendly as it allows for the effective deposition of the enzyme onto unmodified and modified electrode substrates. Three types of substrates were used: an unmodified glassy carbon electrode and two electrodes modified with composite layers—multi-walled carbon nanotubes combined with CuO nanoparticles and multi-walled carbon nanotubes combined with carbon nanofibers, respectively. Biosensors modified with such materials have not been described previously. In the course of the study, electrochemical measurement conditions (composition, concentration and pH of the base electrolyte, sensor response time, and interference effects) were optimized, and sensor parameters were determined. It was found that the modification of the substrate electrode increased the sensitivity of the sensor by more than 25 times in both cases and led to a lower detection limit for the sensor modified with the carbon nanotubes/carbon nanofiber composite. The best performance was achieved with the sensor containing the carbon nanotube/carbon nanofiber composite layer, which showed a linearity range of 0.1–5 µM, a sensitivity of 7.32 ± 0.22 µA/µM, and a limit of quantification of 0.078 µM. The analytical utility of this biosensor was confirmed by its successful application in the determination of estradiol in pharmaceutical preparations and river water samples. Full article

Due to their excellent mechanical properties and good biocompatibility, titanium (Ti) and its alloys are widely used as biomaterials. However, when implanted in the body, metallic materials may cause serious complications such as wear and infection, leading to patient discomfort and, in some cases, the need for revision surgery. Micro-arc oxidation (MAO) is a surface modification technique that offers a promising strategy to overcome these challenges. This study investigated the impact of the microstructure of Ti-25 Ta-xNb alloys (x = 10, 20, and 30 wt%) and the variation in applied voltage during the MAO process on the characteristics of the TiO₂ oxide coatings formed. The alloys were treated by MAO at 200, 250, and 300 V using a bioactive electrolyte containing Ca, P, Mg, and Ag. EDS, SEM, XRD, Raman spectroscopy, and adhesion tests performed characterization. Results indicated that Nb addition stabilized the β phase and anticipated the potentiostatic regime. Increasing the voltage supplied to the system provides greater energy, prolonging the galvanostatic regime and promoting the formation of larger and more uniform pores. The oxide coating thickness ranged from approximately 3 to 10 μm, with a tendency to decrease at higher voltages. The coatings exhibited low c, with anatase and rutile phases predominating, the applied voltage and Nb concentration influencing their relative proportions. Even in small amounts, all electrolyte elements (P, Mg, and Ag) were successfully incorporated into the coatings under all conditions. Raman and XRD analyses confirmed a decrease in anatase and an increase in rutile phases with increasing voltage and Nb content. Mechanical testing revealed good adhesion of the coatings in all samples, with the best results obtained at 200 V. The findings demonstrate that the developed coatings exhibit promising characteristics for future surface engineering strategies aimed at improving the performance of metallic biomaterials. Full article