Search Results (496)

A compact offset-coupled hybrid fiber interferometer (OCHFI) is designed and experimentally demonstrated for simultaneous measurement of salinity and temperature. The sensor integrates multimode fiber (MMF) and offset no-core fiber (NCF) through an intermediate single-mode fiber (SMF), producing distinct interference patterns for multi-parameter sensing. The optimal SMF length was determined through COMSOL simulations (version 6.2) and fixed at $50 \mathrm{c}\mathrm{m}$ to achieve stable and well-separated interference dips. Fast Fourier Transform analysis confirmed that the modal behavior originates from the single-mode-multimode-single-mode (SMS) and single-mode-no-core-single-mode (SNS) segments. Experimentally, Dip 1 exhibits salinity sensitivity of $0.62206 \mathrm{n}\mathrm{m}/\mathrm{‰}$, while Dip 2 shows temperature sensitivity of $0.09318 \mathrm{n}\mathrm{m}/°\mathrm{C}$, both with linearity ($R^2 > 0.99$), excellent repeatability, and stability, with fluctuations within $0.15 \mathrm{n}\mathrm{m}$ over 60 min. To remove cross-sensitivity, both the transfer matrix method and an Artificial Neural Network (ANN) model were employed. The ANN approach significantly enhanced prediction accuracy ($R^2 = 0.9999$) with RMSE improvement approximately 539-fold for salinity and 56-fold for temperature, compared with the analytical model. The proposed OCHFI sensor provides a compact, low-cost, and intelligent solution for precise simultaneous salinity and temperature measurement, with strong potential for applications in marine, chemical, and industrial process control. Full article

Paper plays an important role in the packaging industry due to its low cost, light weight, recyclability and biodegradability. However, the use of paper as a packaging material is severely limited due to its hydrophilicity caused by the hydroxyl groups of cellulose. This study reports a simple preparation of highly hydrophobic kraft paper by a one-step dip coating method using [3-(2,2,3,3-tetrafluoropropoxy)propyl]silsesquioxane, {3-[(2,2,3,3,4,4,5,5-octafluoropentyl)oxy]propyl}silsesquioxane or {3-[(2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl)oxy]propyl}silsesquioxane as hydrophobic agents. As a result of modification of kraft paper, a stable covalently bonded coating is formed on its surface. The coated kraft paper has demonstrated (1) high water resistance (the water contact angle (WCA) values were 124–141°, and the water absorption and the water vapor permeability (WVP) rates were significantly decreased), (2) excellent resistance to aggressive environments and temperature, (3) enhanced mechanical properties (tensile strength increased from 46.8 to 70.8 MPa), and (4) high wear resistance, as confirmed by sandpaper abrasion, bending, and finger-wipe tests. It was shown that the maximum contact angle values were achieved for kraft paper modified with a 5% polymer solution. The results of this study have great potential, given the simplicity of the modification method, for use in the production of paper-based packaging materials with water-repellent, enhanced mechanical and moisture-protective properties. Full article

Significant fluctuations in reservoir water levels occur seasonally during the flood period, adversely affecting the stability of bank slopes. In this paper, a modified mechanical model for the flexural toppling of anti-dip rock slopes under water level fluctuations is established, and an actual deflection equation for rock slabs is derived. The critical length for the flexural toppling failure of rock slabs is calculated, which can be used to evaluate slope stability. Multiple linear regression analysis reveals the relative degree of the influence of each parameter (such as rock slab thickness, rock layer dip angle, water level height, etc.) on the critical length. The results indicate that rock slab thickness plays a controlling role in slope stability. The failure mechanisms of the slope under the influence of water level fluctuations are revealed through fluid–solid coupling numerical simulations. The results indicate that the rise in water level reduces the strength of the rock mass in the submerged zone and generates significant water pressure on the rock mass at the slope toe, leading to its cracking. A rapid drop in water level generates seepage forces detrimental to slope stability and carries away fractured rock particles at the slope toe, ultimately causing slope failure. Finally, the reliability and applicability of the proposed method are validated through numerical simulations, case studies, and comparisons with existing analytical solutions. Full article

Polyvinyl chloride (PVC) is a widely used polymer in composite systems due to its versatility and processability, with growing use in advanced engineering applications. This study presents the formulation, processing optimisation, and detailed characterisation of a hot-dip PVC-based plastisol composite coating developed for electrical insulation in electric vehicle (EV) battery systems. A series of plastisol formulations with varying filler contents were prepared and applied via dip-coating at withdrawal speeds of 5, 10, and 15 mm s⁻¹. The 5 mm s⁻¹ withdrawal speed resulted in the most uniform coatings with thicknesses of 890–2100 µm. Mechanical testing showed that lower filler content significantly improved performance: Group 1 (lowest filler) exhibited the highest tensile strength (11.9 N mm⁻²), elongation at break (465%), tear strength (92 N mm⁻¹), and abrasion resistance. SEM and EDX analyses confirmed more homogeneous filler dispersion in Group 1, while FTIR spectra indicated stronger polymer–plasticiser interactions. Contact-angle measurements showed an increase of ${38}^{\circ }$ in low-filler samples, indicating enhanced surface hydrophobicity. Furthermore, Group 1 coatings demonstrated superior dielectric strength (22.1 kV mm⁻¹) and excellent corrosion resistance, maintaining integrity for over 2000 h in salt-spray testing. These findings highlight the importance of filler optimisation in balancing mechanical, electrical, and environmental performance. The proposed PVC-based composite coating offers a durable, cost-effective solution for next-generation EV battery insulation systems and has potential applicability in other high-performance engineering applications. Full article

In this work, we present a gettering technique for multicrystalline silicon (mc-Si) by combining a nanowire structure with thermal treatment under nitrogen in an infrared lamp furnace. The silicon nanowires were elaborated using the Silver Nanoparticles Chemical Etching (Ag-NPsCE) technique. The optimal conditions for achieving effective gettering were determined based on the minority carrier lifetime (τ_eff) measurements. The results show τ_eff as a function of the gettering temperature and etching time, both before and after the removal of Ag nanoparticles using HNO₃. In both cases, the surface was identically treated with a 10% HF dip immediately prior to the carrier lifetime measurements. The highest τ_eff value, prior to Ag removal, was obtained after an etching duration of 3 min and was 6 µs at an excess carrier density Δn = 1 × 10¹⁴ cm⁻³. Moreover, τ_eff improves after silver removal. Therefore, removing Ag atoms using an aqueous HNO₃ solution is necessary to prevent this issue. Following Ag nanoparticle removal, τ_eff further increases, reaching 19 µs at a gettering temperature of 850 °C. Similarly, the electrical conductivity (ρ) and carrier mobility (μ) improve significantly after gettering, where the resistivity increases from 5.5 Ω·cm for the reference mc-Si to 1.9 Ω·cm, and the mobility rises from 122 cm²·V⁻¹·s⁻¹ to 253 cm²·V⁻¹·s⁻¹ after nanowire-based gettering at 850 °C. Overall, this method provides a scalable, practical, and cost-effective route to optimize mc-Si for high-performance photovoltaic applications. Full article

A temporally periodic model is presented to describe the vertical profile of internal gravity waves in the F region of the Earth’s ionosphere where the waves are subject to a magnetic force due to the high concentration of ions. The configuration studied is representative of the situation where the geomagnetic field is approximately constant and is so strong that the angular gyrofrequency of the ions is very large compared with the ion-neutral collision frequency, which is in turn larger than the angular frequency of the gravity waves. We examine the situation where the gravity wave amplitude is small enough that the equations for the neutral fluid flow can be linearized. This allows for the description of wave propagation in terms of a system of coupled equations that include the effects of ion drag on waves for any orientation of the magnetic field. It is assumed that the background neutral fluid flow is nonzero and horizontal, but there is no vertical shear, and that the wave amplitude depends on altitude only, and an exact analytical solution is readily found. This dynamical model captures some essential features of ionospheric gravity waves that are consistent with observational measurements. In particular, the ion drag acts to damp the waves in the direction of vertical propagation and increase their vertical wavelength relative to the corresponding wavelength in the neutral atmosphere. The vertical damping rate and the vertical wavelength both depend on the dip angle of the magnetic field. When the magnetic field acts in the direction of the gravity lines of constant phase, there is no damping, and the vertical wavelength is the same as that of the corresponding waves in the neutral atmosphere. The dip angles that produce stronger damping also result in waves with greater wavelengths. Full article

This work prepared SnO₂ coatings on 304 stainless steel via the sol–gel and dip-coating techniques, using tin (II) chloride (SnCl₂) and tin (II) oxalate (SnC₂O₄) as precursors. The crystal structure analyzed by X-ray Diffraction (XRD) confirmed the cassiterite-type SnO₂ in both cases. The corrosion resistance in a 3 wt.% NaCl solution was evaluated by polarization resistance (Rp) and anodic potentiodynamic polarization. Coatings derived from the SnC₂O₄ precursor demonstrated exceptional performance, reducing the corrosion rate by up to three orders of magnitude (from 0.0973 mpy for uncoated steel to 0.00015 mpy), corresponding to a protection efficiency of 99.8%. In contrast, coatings from the SnCl₂ precursor increased the corrosion rate. X-ray Photoelectron Spectroscopy (XPS) analysis confirmed that this detrimental effect was due to the presence of chlorine (5.54 wt.%), which acted as an initiation site for pitting corrosion. Atomic force microscopy (AFM) and XRD of the effective SnC₂O₄-derived coatings revealed a homogeneous surface with low roughness and a textured cassiterite structure. The primary limitation of this work is that the sol–gel synthesis route using SnCl₂ is unsuitable for corrosion protection in chloride environments due to the incorporation of aggressive chlorine ions, whereas the chlorine-free SnC₂O₄ precursor yields highly protective SnO₂ coatings. Full article

Edible coatings enriched with antioxidants offer a promising approach to prolong the shelf life of oxidation-sensitive foods such as nuts. Nonetheless, not all formulations provide the expected protection, and understanding why is equally important. The aim of this study was to assess the effect of an Arabic gum/gelatin/ascorbyl palmitate (GAR/GEL/AP) coating on the quality of hazelnut kernels during storage at 23 °C and ~40% relative humidity. The coating was applied by dipping hazelnuts in a 20% ethanolic solution containing GAR/GEL 75/25 blend (10% w/w), glycerol (1% w/w), Tween 80 (0.25% w/w), and AP (2% w/w), followed by drying. Control (uncoated) and coated hazelnuts were stored in plastic containers and evaluated at 1, 2, 4, 8, and 16 weeks for weight loss, moisture content, hardness, color, 2,2-diphenyl-1-picrylhydrazyl radical (DPPH*) scavenging activity, acid and peroxide values, and thiobarbituric acid reactive substances (TBARS) level. Coated hazelnuts showed higher initial moisture content (8.17%), stabilizing at 4.80% after one week, compared to 3.35% in uncoated samples. This increased moisture led to greater storage-related weight loss. The coating darkened the nuts and reduced their yellow hue. It had no significant effect on hardness, peroxide value, or TBARS index, but notably enhanced the antiradical potential. After 16 weeks, coated nuts had an acid value ~10 mg KOH/g lower than the control. In conclusion, the coating improved antioxidant capacity and reduced hydrolytic, but not oxidative, rancidity in hazelnuts. Therefore, further optimization of the coating formulation or application method is necessary to more effectively improve the shelf life of hazelnuts. Full article

Jujube (Ziziphus jujuba Mill.) is a nutritionally rich and economically significant fruit, highly valuable for its flavor, bioactive compounds, and therapeutic properties. However, it is highly perishable and has a short postharvest lifespan. This review aims to provide knowledge for preserving quality and improving postharvest storage by integrative strategies aimed at extending the shelf life of jujube. The literature was collected from recent peer-reviewed studies on postharvest physiology and handling technologies of jujube fruit. Key physiological factors, influencing postharvest deterioration such as water loss, softening, browning, and decay, are discussed, along with the underlying biochemical and enzymatic mechanisms driving quality decline. Conventional strategies such as cold storage, MAP, and CA effectively slow respiration, delay reddening, and extend storage up to 2–4 months, while emerging approaches such as ozone and cold plasma treatments reduce microbial decay and maintain antioxidant activity. Edible coatings like chitosan, aloe vera, and composites cut weight loss by 20–40%, and chemical regulators such as 1-MCP and calcium dips further delay ripening, preserve firmness, and enhance postharvest quality. Emphasis is placed on integrating innovative technologies with physiological insights to optimize storage conditions, control microbial contamination, and maintain nutritional integrity. The significance of this review lies in integrating physiological insights with innovative preservation methods, offering practical guidance for researchers, growers, and industry stakeholders to achieve sustainable, safe, and market-oriented solutions for jujube storage. Full article

This study details the sustainable synthesis and characterization of electrospun zinc oxide nanofibers, uniquely derived from industrial waste streams. Our approach leverages diverse industrial byproducts—specifically sal ammoniac skimming from hot-dip galvanizing, electric arc furnace dust, and galvanization flue dust—as sustainable raw materials. Following hydrometallurgical treatment with various leaching agents (HCl, (NH₄)₂CO₃, or H₂SO₄) to obtain zinc-rich leachates, electrospinning solutions were formulated. The resulting fibers were subsequently calcined, yielding three distinct ZnO-based materials. Comprehensive characterization by XRD, SEM-EDX, and TEM revealed that the choice of leaching strategy significantly influenced the resultant fibers’ morphology and chemical composition. To demonstrate the potential applicability of these waste-derived materials, their photocatalytic activity was assessed through the degradation of methylene blue dye under UVA irradiation. ZnO fibers derived from HCl leaching exhibited remarkable photodegradation capabilities, achieving nearly complete dye removal within 690 min at optimal catalyst-to-dye ratios. Conversely, the H₂SO₄-prepared sample displayed impaired efficiency, primarily due to the formation of an undesirable Al₂ZnO₄ phase stemming from high aluminum content in the input waste, a critical consideration for waste-to-product strategies. The results showed that the cost-effective ZnO fibers obtained by electrospinning from industrial waste products have potential for applications in photocatalytic water treatment. Full article

A high-precision coal seam model is crucial to improving the adaptability of unmanned mining technology to geological conditions. However, the accuracy of a coal seam model constructed with boreholes and geophysical data is far from the required accuracy of unmanned mining (sub-decimeter level). Therefore, it is necessary to collect geological data revealed by mining and to update the coal seam model dynamically. As a solution to this problem, this paper proposes a new method for conducting off-site geological surveying of longwall faces by integrating multi-source monitoring data. The spatial attitudes of hydraulic supports are monitored to estimate the local dip angles of longwall face. A roof line calculation model was established, which integrates the local inclination angle of the longwall face, the number of hydraulic supports, and the roof elevation of the two roadways. Meanwhile, the local coal–rock columns at the camera observation point are extracted automatically using image segmentation and a proportional relationship between the picture and the actual scene. Coal and rock walls and a support guarding plate in the longwall face image are identified accurately using the coal-rock support segmentation model trained with U-net. Then, the height of the coal (or rock) wall above the coal–rock interface is estimated automatically according to the image segmentation and the similar proportion equation of actual longwall face and longwall face image. Combined with mining height information, the local coal–rock column can be extracted. Finally, the geological surveying profile of longwall face can be obtained by integrating the estimated roof line and local coal–rock columns. The field test demonstrated the efficacy of the method. This study helps to address a long-standing limitation of insufficient geological adaptability of intelligent mining technology. Full article

To address stability and safety issues in hydraulic support design under inclined–declined and large-dip-angle working conditions, this paper proposes a design-driven dynamic pose–load co-evolution solution method based on the physical entity of the ZFY12000/21/36D hydraulic support. The feasibility of the proposed method is demonstrated through theoretical analysis, spatial modeling, and experimental verification. First, a spatial coordinate system describing hydraulic support pose is established based on Denavit–Hartenberg (DH) theory, constructing a “physical space-geometric coordinate system-DH parameter space” pose mapping model via DH principles, matrix iteration, and kinematic simulation. Second, a load-bearing characteristic analytical method is developed through systematic coupling analysis of dip angle, pose, and load distribution. Finally, coal mine field data collection and hydraulic support test platform experiments analyze load-bearing characteristics under varying poses and loads. Results show Root Mean Square Error (RMSE) values of 0.836° for the front link inclination, 0.756° for the rear link, 0.114° for the balance ram, and 0.372° for the column; load-bearing state evolution under pose–load synergy aligns with theoretical models, confirming method feasibility. This approach fills a domain gap in hydraulic support dip–pose–load co-solving and provides critical references for designing hydraulic support products under extreme dip-angle operations. Full article

Copper contamination in the environment poses significant risks to both soil and human health, making the need for reliable monitoring methods crucial. In this study, we report the use of the EmStat Pico module as potentiostat to develop a portable electrochemical biosensor for copper detection, utilizing yeast Saccharomyces cerevisiae cells immobilized on a polydopamine (PDA)-coated screen-printed electrode (SPE). By optimizing the sensor design with a horizontal assembly and the volume reduction in the electrolyte solution, we achieved a 10-fold increase in current density with higher range of copper concentrations (0–300 µM CuSO₄) compared to traditional (or previous) vertical dipping setups. Additionally, the use of genetically engineered copper-responsive yeast cells further improved sensor performance, with the recombinant strain showing a 1.7-fold increase in current density over the wild-type strain. The biosensor demonstrated excellent reproducibility (R² > 0.95) and linearity over a broad range of copper concentrations, making it suitable for precise quantitative analysis. To further enhance portability and usability, a Bluetooth-enabled electrochemical platform was integrated with a web application for real-time data analysis, enabling on-site monitoring and providing a reliable, cost-effective tool for copper detection in real world settings. This system offers a promising solution for addressing the growing need for efficient environmental monitoring, especially in agriculture. Full article

Listeria monocytogenes presents a considerable threat in cooked chicken products, especially those that are ready-to-eat, like deli meats. The aim of this study was to evaluate the antimicrobial efficacy of oregano essential oil (Satureja hortensis: SHEO) against L. monocytogenes contamination of ready-to-eat cooked chicken meat during storage. The chemical content of SHEO was identified using GC-MS, with its antimicrobial properties confirmed through Kirby–Bauer disk diffusion tests. GC analyses of the SHEO used in the study showed that it contained 14.69% carvacrol and 10.61% thymol. L. monocytogenes strain NCTC 5348 was inoculated into chicken meat through a dipping technique at concentration levels of 2 × 10⁷ CFU/mL before and after application of SHEO solution (2 μL/mL). Inoculated and SHEO-treated meat samples were stored −20 °C, +4 °C, and +10 °C under both traditional and vacuum packaging conditions for 28 days. Results indicated that SHEO significantly suppressed the growth of L. monocytogenes (approximately 1 log CFU/g), especially during the first 5–7 days at +4 °C in both packaging types. Vacuum packaging prolonged the antimicrobial effect of SHEO compared to conventional packaging at +4 °C and +10 °C, approximately 1.1–1.3 log CFU/g for 14 days. The antimicrobial activity of SHEO was limited to a range of approximately 0.1–0.5 log CFU/g at −20 °C compared to the control. These results suggest that combining essential oils with modern packaging methods can provide an effective approach to controlling cold-tolerant pathogens such as L. monocytogenes, thereby improving the shelf life and safety of ready-to-eat meat products. Full article

The aim of this study was to evaluate the haemostatic potential and biocompatibility of a newly developed composite material for its use in blood-contacting applications. Based on promising reports on polylactide (PLA), sodium alginate (ALG), and bioactive additives such as hardystonite (HT) and zinc sulphide (ZnS), a melt-blown PLA nonwoven was modified via dip-coating using an ALG solution as a matrix for incorporating HT and ZnS particles, resulting in the PLA-ALG-ZnS-HT composite. The material was characterised in terms of surface morphology, specific surface area, pore volume, average pore size, and zeta potential (pH~7.4). Haemostatic activity was assessed by measuring blood coagulation parameters, while biocompatibility was evaluated through the viability of human peripheral blood mononuclear (PBM) cells and human foreskin fibroblasts (Hs68). Genotoxicity was analysed using the comet assay and plasmid relaxation test. Results confirmed a uniform alginate coating with dispersed HT and ZnS particles on PLA fibres. The modification increased the surface area and pore volume and caused a shift toward less negative zeta potential. Haemostatic testing showed prolonged activated partial thromboplastin time (aPTT), likely due to Zn²⁺ interactions with clotting factors. Biocompatibility tests showed high cell viability and no genotoxic effects. Our findings suggest that the PLA-ALG-ZnS-HT composite is safe for blood and skin cells and may serve as an anticoagulant material. Full article