Search Results (165)

In this research project a large linear electromagnetic actuator (LLEA) was designed and manufactured. The electromagnetic performance was published in previous works, but in this paper we focus on the technological challenges related to the manufacturing in particular. This LLEA was based on the magnet-free switched-reluctance principle, having six effective energised stator “teeth” and four passive mover parts (4:6 ratio). Various aspects and challenges encountered during the manufacturing, transport, and assembly are discussed. Thermal expansion of steel contributed to the decision of the modular design, with each module having 1.3 m in length, with a 2 mm longitudinal dilatation gap. The initial prototype was tested with a 10.6 m length, with plans to extend the test track to 60 m, which was fully achievable due to the modular design and required 29 tons of electrical steel to be built. The stator laminations were cut by a bespoke progressive tool with stamping, and other parts by a CO₂ laser. Mounting was based on welding (back of the stator) and clamping plates (through insulated bolts). The linear longitudinal force was on the order of 8 kN, with the main air gap of 7.5–10 mm on either side of the mover. The lateral forces could exceed 40 kN and were supported by appropriate construction steel members bolted to the concrete floor. The overall mechanical tolerances after installation remained below 0.5 mm. The technology used for constructing this prototype demonstrated the cost-effective way for a semi-industrial manufacturing scale. Full article

Next to solid wood, laminated particleboard is the most widely used wood-based material in the furniture industry. Ensuring the high quality of the laminate surface after machining is of critical importance for furniture manufacturers, particularly prior to the edge banding process, as this process significantly influences the final aesthetic and functional quality of panel elements. The objective of this review article is to gather and evaluate the current state of knowledge regarding the influence of machining process parameters and the physical and mechanical properties of laminated particleboard on machining quality. Particular emphasis is placed on the occurrence of laminate damage, commonly referred to as delamination, a prevalent defect in the furniture manufacturing sector. Both categories of influencing factors—process-related and material-related—are analyzed within the context of the three primary technological processes employed in the woodworking industry, namely drilling, cutting, and milling. The analysis revealed that a persistent research gap concerns the relationship between machining quality and material parameters, particularly in the case of milling—a process of critical importance in the furniture industry. Full article

Integrating recyclates into food packaging is key towards circularity while meeting functionality and safety requirements; however, associated environmental impacts remain underexplored. This gap was addressed through a cradle-to-gate life cycle assessment, using the Environmental Footprint method, along with substitution and cut-off approaches for handling the multifunctionality of recycling. Recyclates were derived from polyethylene (PE)-rich household food packaging waste, purified via delamination-deinking. Firstly, results show that shifting from virgin multi-material to mono-material multilayer structures with or without recyclates, while maintaining functionality, offers environmental benefits. Secondly, recyclates should sufficiently substitute virgin materials in quantity and quality, decreasing the need for primary plastics and avoiding recyclate incorporation without functionality. Otherwise, thicker laminates are obtained, increasing processability challenges and environmental impacts, e.g., 12% for particulate matter, and 14% for mineral-metal resource use when the recycle content rises from 34 to 50%. Thirdly, a fully closed loop for flexible food packaging is not yet feasible. Key improvements lie in reducing residues generated during recycling, especially in delamination-deinking, lowering energy use in recompounding, and using more efficient transport modes for waste collection. Further research is essential to optimise the innovative technologies studied for flexible food packaging and refine them for broader applications. Full article

During the machining of unidirectional carbon fiber-reinforced polymers (UD-CFRPs), their anisotropic characteristics and the complex cutting conditions often lead to defects such as delamination, burrs, and surface/subsurface damage. This study systematically investigates the effects of different fiber orientation angles (0°, 45°, 90°, and 135°) on cutting force, chip formation, stress distribution, and damage characteristics using a coupled macro–micro finite element model. The model successfully captures key microscopic failure mechanisms, such as fiber breakage, resin cracking, and fiber–matrix interface debonding, by integrating the anisotropic mechanical properties and heterogeneous microstructure of UD-CFRPs, thereby more realistically replicating the actual machining process. The cutting speed is kept constant at 480 mm/s. Experimental validation using T700S/J-133 laminates (with a 70% fiber volume fraction) shows that, on a macro scale, the cutting force varies non-monotonically with the fiber orientation angle, following the order of 0° < 45° < 135° < 90°. The experimental values are 24.8 N/mm < 35.8 N/mm < 36.4 N/mm < 44.1 N/mm, and the simulation values are 22.9 N/mm < 33.2 N/mm < 32.7 N/mm < 42.6 N/mm. The maximum values occur at 90° (44.1 N/mm, 42.6 N/mm), while the minimum values occur at 0° (24.8 N/mm, 22.9 N/mm). The chip morphology significantly changes with fiber orientation: 0° produces strip-shaped chips, 45° forms block-shaped chips, 90° results in particle-shaped chips, and 135° produces fragmented chips. On a micro scale, the microscopic morphology of the chips and the surface damage characteristics also exhibit gradient variations consistent with the experimental results. The developed model demonstrates high accuracy in predicting damage mechanisms and material removal behavior, providing a theoretical basis for optimizing CFRP machining parameters. Full article

In this work, the mechanical properties of jute fiber-reinforced polymers were investigated, considering two manufacturing technologies—wet layups and vacuum-assisted resin infusion—with the aim of developing cost-effective composite materials based on natural fibers. In the manufacturing process, two different types of resins were used, specific to each technology. Specimens measuring 25 mm × 200 mm were cut from the resulting laminates at three orientations (0°, 45° and 90° with respect with the weft orientation), and they were subjected to tensile tests. The results showed that resin infusion yielded superior stiffness and strength values when compared to the wet layup. Multi-scale modeling techniques were applied in order to estimate the properties of the fibers and evaluate the orthotropic properties of the composites, and virtual material models that included orthotropic elasticity and the anisotropic Hill plasticity formulation were developed and evaluated, managing to reproduce the experimental data using finite element analyses with decent accuracy. Full article

Carbon fibre reinforced composite (CFRP) laminates are widely used in high-tech industries. However, their assembly often requires a drilling process that can create defects. Therefore, studies on the drill tip angle have sought to minimize the surface area affected by these defects and improve the internal hole quality. In this work, drilling was carried out under dry conditions at a constant cutting speed for four different feed rates in the epoxy–carbon-based thermosetting laminate (EPX-C). Two carbide drills with point angles of 118° and 140° were used. The results showed the occurrence of chipping-type delaminations on both the hole entry and exit surfaces, with the latter being more severely affected. The delamination factor values obtained indicated that the 118° drill performed better than the 140° drill. The results were also compared with those obtained in a previous study using drills with angles of 60° and 130°. Although the values were higher, they followed the same trend of reduction with increasing feed. In terms of surface finish, the average roughness (Ra) values obtained with the 140° drill were better at the lowest feed rate. Full article

In the composite materials industry, the fabrication of complex parts often necessitates the use of specialized tools, such as milled molds with intricate geometries. Among these, machined aluminum molds are widely regarded as effective tools for laminating CFRP (Carbon Fiber Reinforced Polymer) prepreg materials. However, the cost and time associated with machining aluminum molds can be significant. This paper presents a novel method for manufacturing molds using polymeric acrylic resin combined with aluminum trihydrate material (commercially known as DuPont Corian materials), offering a potential alternative with reduced complexity and cost. The study investigates the influence of various milling parameters, such as tool speed, tool type, feed rate, and depth of cut on the mechanical properties and surface finish of the molds. Also, laminating tests are conducted; results indicate that laminating tools produced through this method achieve competitive mechanical performance, including a hard, smooth surface with low roughness, making them viable candidates for industrial use. The proposed approach is particularly beneficial in terms of reducing machining time and overall costs while maintaining the necessary precision and durability for high-performance applications. This method, therefore, represents a promising solution for manufacturers seeking to optimize mold production processes in the composite materials industry. Full article

The use of composite materials within extreme environments is an exciting frontier in which a wealth of cutting-edge developments have taken place recently. Although there is vast knowledge of composites’ behaviour in standard room temperature and humidity, there is a great need to understand their performance in ‘hot/wet’ conditions, as these are the conditions of their envisaged applications. One of the key failure mechanisms within composites is interlaminar fracture, commonly referred to as delamination. The environmental effects of moisture and elevated temperatures on interlaminar fracture toughness are therefore essential design considerations for laminated aerospace-grade composite materials. IM7/8552, a toughened epoxy/carbon fibre reinforced polymer, was experimentally characterised in both ‘Dry’ and ‘Wet’ conditions at 23 °C and 90 °C. A moisture uptake study was conducted during the ‘Wet’ conditioning of the material in a 70 °C/85% relative humidity environment. Dynamic mechanical thermal analysis was carried out to determine the effect of moisture on the glass transition temperature of the material. Mode I initiation and propagation fracture properties were determined using double cantilevered beam specimens and Mode II initiation fracture properties were deduced using end-notched flexure specimens. The effects of precracking and the methodology of high-temperature testing are discussed in this report. Mode I interlaminar fracture toughness, $G_{IC}$, was found to increase with elevated temperatures and moisture content, with $G_{IC}=0.205{\mathrm{kJ}/\mathrm{m}}^2$ in ‘Dry 23 °C’ conditions increasing by 26% to $G_{IC}=0.259{\mathrm{kJ}/\mathrm{m}}^2$ in ‘Wet 90 °C’ conditions, demonstrating that the material exhibited its toughest behaviour in ‘hot/wet’ conditions. Increased ductility due to matrix softening and fibre bridging caused by temperature and moisture were key contributors to the elevated $G_{IC}$ values. Mode II interlaminar fracture toughness, $G_{IIC}$, was observed to decrease most significantly when moisture or elevated temperature was applied individually, with the combination of ‘hot/wet’ conditions resulting in an 8% drop in $G_{IIC}$, with $G_{IIC}=0.586{\mathrm{kJ}/\mathrm{m}}^2$ in ‘Dry 23 °C’ conditions and $G_{IIC}=0.541{\mathrm{kJ}/\mathrm{m}}^2$ in ‘Wet 90 °C’ conditions. The coupled effect of fibre-matrix interface degradation and increased plasticity due to moisture resulted in a relatively small knockdown on $G_{IIC}$ compared to $G_{IC}$ in ‘hot/wet’ conditions. Fractographic studies of the tested specimens were conducted using scanning electron microscopy. Noteworthy surface topography features were observed on specimens of different fracture modes, moisture saturation levels, and test temperature conditions, including scarps, cusps, broken fibres and river markings. The qualitative features identified during microscopy are critically examined to extrapolate the differences in quantitative results in the various environmental conditions. Full article

In the era of Industry 4.0, equipment maintenance is shifting toward data-driven strategies. Traditional methods rely on usage time or cycle counts to estimate component lifespan. This often causes early replacement of parts, leading to increased production costs. This study focuses on the cutter system of a roller laminator used in printed circuit board (PCB) manufacturing. An accelerometer is used to collect vibration signals under normal and abnormal states. Fast Fourier transform (FFT) is used to convert time-domain data into the frequency domain, then key statistical features from critical frequency bands are extracted as independent variables. The study applies logistic regression (LR), random forest (RF), and support vector machine (SVM) for predictive modeling of the cutting tool’s condition. The results show that the prediction accuracies of these models are 87.55%, 93.77%, and 94.94%, respectively, with SVM performing the best. Full article

Overcoming the limitations of powder-based additive manufacturing processes is a crucial aspect for the manufacturing of patient-specific sophisticated implants with tailored properties. Within this work, a novel manufacturing process for the fabrication of polymer-based implants is proposed. This manufacturing process is inspired by the laminated object manufacturing technology and is based on using thin films as raw material, which are processed using an ultrafast laser source. Utilizing thin films as a starting material helps to avoid powder contamination during additive manufacturing, thus supporting the generation of internal cavities that can be filled with secondary phases. Additionally, the use of medical materials mitigates the burden of a later certification of potential implants. Furthermore, the ultrafast laser supports the generation of highly resolved structures smaller than the average layer thickness (from 50 to 100 µm) through material ablation. These structures can be helpful to obtain progressive part properties or a targeted stress flow, as well as a specified release of secondary phases (e.g., hydrogels) upon load. Within this work, first investigations on the joining, cutting, and structuring of thin polymer films with layer thickness of between 50 and 100 µm using a ps-pulsed laser are reported. It is shown that thin film sizes of around 50 µm could be structured, joined, and cut successfully using ultrafast lasers emitting in the NIR spectral range. Full article

In this work, we propose a lightweight pneumatic gripper that can grasp objects from either the outer or inner surfaces. Inspired by the Miura-ori pattern, the gripper is fabricated by laminating films with different cutting patterns to form the crease lines and air chambers. The asymmetry in the thickness of the top and bottom sides of the air chambers causes the gripper’s end to rotate in a predetermined direction upon inflation, enabling a dual-morphing grasping action. The dual morphings include an outward grasping morphing (grasping from the outer surface) and an inward grasping morphing (grasping from the inner surface). The deflection of the gripper’s end, induced by the air chamber’s inflation, is theoretically analyzed using a simplified one-dimensional model. We conducted both finite element modeling and experimental measurements to investigate the influence of the air chamber’s design parameters. Weighing only 4.5 g, the gripper can lift objects more than ten times of its own weight. This study provides a valuable design insight for developing more flexible and adaptable soft grippers capable of holding objects with a wider range of geometrical characteristics. Full article

The increasing demand for high-performance materials has led to an increase in the use of carbon fibre-reinforced plastics (CFRPs) in recent decades, increasing the waste from end-of-life materials and off-cuts. The recycling of CFRPs, especially when thermosetting matrices are used, still remains an open challenge for academia and industry, with chemical, thermal and mechanical strategies being explored. Among them, mechanical methods have garnered growing interest since they do not require high specific energy consumption or expensive apparatus. However, from the literature it was observed that when using these methods, traces of old matrix remain on the fibre’s surface, compromising the fibre–matrix adhesion efficiency and limiting their use in recycled composites. On the other hand, solvothermal methods are known for their high matrix dissolution efficiency that in turn improves the fibre–matrix adhesion. Therefore, in this paper, end-of-life CFRPs from the aeronautic sector were machined using a milling-based mechanical recycling method, while to remove the residual matrix from the fibre surface, the recovered chips were chemically treated with a two-step treatment at low temperature. Then, two types of recycled composite laminates were manufactured using the compression moulding technique: the first using recycled fibres only from the mechanical recycled method, and the second one using recycled fibres deriving from both recycling methods. The feasibility of the process was analysed observing that the additional chemical treatment led to a mass loss of almost 24% in the recycled fibres. FTIR analysis revealed the complete matrix dissolution since no spectra of epoxy resin groups were detected. Finally, the flexural behaviour of the recycled composites was investigated, revealing an increase in the flexural strength and modulus of the second sample typology, respectively, of almost 42% and 76% thanks to the improved fibre–matrix adhesion as a consequence of the solvothermal treatment. Full article

Composite materials have experienced a significant increase in demand over the past five decades. This growing usage has led to a considerable production of waste, particularly from prepreg scraps, which can account for up to 35% of the purchased material. This paper explores the recycling of prepreg scraps by cutting them into smaller patches and reassembling them into new sheets. The study follows a dual approach: mechanical testing on two different types of samples is presented, along with numerical modeling strategies designed to capture not only the mechanical behavior of the new recycled material but also the failure modes of the samples. The experimental results demonstrate the feasibility of the proposed technique, with samples made from prepreg scraps retaining 85%, 57%, and 78% of the original flexural modulus, strength, and interlaminar strength, respectively. The numerical models not only fit closely to the experimental data but also successfully predict the failure modes of the new material under the two different loading conditions. The primary highlights of this work lie in (i) its innovative approach to recycling prepreg scraps, which is capable of successfully recovering material otherwise sent to landfill; (ii) an ordinated and easy-to-automate recovery process; and (iii) in the modeling strategies of the new material. The study eventually proposes the development of an “equivalent lamina” made of scrap material that can be used in standard lamination processes to manufacture components with load-bearing capabilities. Full article

A study of cryogenic drilling in sandwich composites was carried out. The materials used were carbon-fiber-reinforced polymer sandwich sheets with an inner foamed polyvinyl chloride core, composites with applications including protection structures of polar engineering equipment. The purpose of this study was to determine the feasibility of drilling at low temperatures using this composite by analyzing the thrust forces and the inlet and outlet diameters of the hole due to their influence on hole quality and their importance in a preassembly operation. Experimental tests were performed in laminates with thicknesses of 12 mm and 6 mm, drilling with liquid nitrogen (LN₂) as a refrigerant to reach temperatures below −120 °C under cutting conditions of 2000–6000 rpm for drill bit rotation speeds and 200–600 mm/min for feed rates. Variables such as thrust forces and circularity error were measured, and a design of experiments, analysis of variance, and regression models allowed us to identify the influence of cutting conditions and foam thickness. Optimal cutting conditions were identified and contrasted: 2100–3100 rpm for drill bit rotation speeds and 200–320 mm/min for feed rates. The diameters achieved low deviations, H7 and H8 tolerances for inlet and outlet diameters, respectively, which allows for avoiding additional preassembly operations, which can be important during plate assembly using LN₂ and in maintenance operations. Although good results have been obtained with other materials such as glass-fiber- and carbon-fiber-reinforced polymers, this sandwich material is lighter. Full article

The present study aims to evaluate thin plate-injected polypropylene (PP) composites containing short aramid fibers (AF) and graphene nanoplatelets (GNPs). The aramid fibers were manually cut to a length of 10 mm and added to the polypropylene matrix at a concentration of 10 wt.%. Additionally, GNPs were incorporated at concentrations of 0.1, 0.25, and 0.5 wt.%. Maleic anhydride grafted polypropylene (MAPP) was used at a concentration of 2 wt.% to improve the adhesion and compatibility between the polymer matrix and the fillers. Thermal analyses, tensile and flexural tests, and dynamic mechanical thermal analysis were performed, followed by statistical analysis using ANOVA and Tukey’s test. The composites demonstrated significant improvements in storage and loss moduli compared to neat polypropylene. With the addition of AF and GNPs, tensile strength increased to 46.8 MPa, which represents a 265% enhancement compared to PP. Similarly, flexural strength reached 62.4 MPa, significantly higher than the 36.73 MPa for PP, particularly for the composite containing AF and 0.25 wt.% GNPs. The results presented in this study highlight the synergistic effect of aramid fibers and GNPs on PP. These improvements make the proposed composites highly promising for a range of applications, including ballistic interlayered aramid/thin-plate laminates. Full article