Search Results (133)

This study reports the preparation of benzalkonium chloride-modified montmorillonite (MMT-1227) via a wet chemical method and systematically investigates its structural characteristics and antimicrobial/antifungal properties. The modified montmorillonite was comprehensively characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Brunauer–Emmett–Teller (BET) surface area analysis. The results confirmed the successful intercalation of benzalkonium chloride into montmorillonite layers, leading to altered surface morphology, increased interlayer spacing, and enhanced hydrophobicity. Antimicrobial assays demonstrated that MMT-1227 exhibits potent activity against both Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus, with inhibition zone diameters of 15.6 ± 0.2 mm and 17.7 ± 0.2 mm, respectively, and minimum inhibitory concentrations (MIC) of 1 mg/mL and 0.5 mg/mL. When incorporated into latex paint at a mass fraction of 0.3%, MMT-1227 achieved a 99.9% antibacterial rate against both strains after 24 h. Additionally, fungal resistance testing in accordance with GB/T 1741-2020 revealed that the modified paint films completely inhibited the growth of eight common mold strains (e.g., Aspergillus niger, Trichoderma viride), achieving a resistance grade of 0. These findings validate that benzalkonium chloride modification endows montmorillonite with excellent antimicrobial and antifungal properties, highlighting its potential as a high-performance additive for functional coatings and related antimicrobial materials. Full article

Plant latex is a rich source of proteolytic enzymes with potential biomedical applications, particularly in hemostasis. Among them, thrombin-like enzymes (TLEs) have garnered interest in their ability to mimic thrombin by catalyzing the conversion of fibrinogen to fibrin, facilitating clot formation. While TLEs from snake venoms have been well-characterized and applied clinically, their plant-derived counterparts remain underexplored. This review critically examines the structural and functional characteristics of TLEs from plant latex, comparing them to animal-derived TLEs and evaluating their role in both procoagulant and fibrinolytic processes. Emphasis is placed on dual fibrinogenolytic and fibrinolytic activities exhibited by latex proteases, which often vary with concentration, incubation time, and protease type. In vitro coagulation assays and electrophoretic analyses are discussed as critical tools for characterizing their multifunctionality. By addressing the knowledge gaps and proposing future directions, this paper positions plant latex proteases as promising candidates for development in localized hemostatic and thrombolytic therapies. Full article

The build-up of a fouling layer on the membrane surface is believed to deteriorate flux and salt rejection by hindering back-diffusion of rejected salts, a phenomenon called cake-enhanced concentration polarization (CECP). Nevertheless, CECP effects have not been linked to the salt rejection properties of the membrane. Furthermore, the decline in salt rejection during fouling has not been related to the decreasing flux, to elucidate the effects of flux on solution rejection as described by the solution-diffusion (SD) model. Therefore, this work examined whether CECP is substantial in membranes with poor salt-rejection properties. Fouling was performed using sodium alginate, Al₂O₃, latex, and SiO₂. The effects of fouling on salt rejection were studied using two nanofiltration (NF) membranes, namely NF270 membrane (46% NaCl rejection) and NF90 membrane (>97% NaCl rejection). The measured flux and salt rejection profiles were compared to those predicted by the CECP and SD models. Overall, the flux declined more (30–60%) for the NF90 membrane (contact angle: 50 ± 3°) compared to the NF270 membrane (10–55%, contact angle: 39 ± 2°) under similar hydrodynamic conditions. Moreover, fouling had more effects on NaCl rejection for the NF90 membrane (2–45% decline) compared to the NF270 membrane (10–30% decline). The decrease in NaCl rejection for the NF90 membrane was ascribed to CECP effects and declining flux. Contrary, CECP effects were less important for the NF270 membrane, and rejection declined due to reduction in flux as predicted by the SD model, indicating that CECP may not be predominant in membranes that poorly reject salts. Full article

Imidazole dipeptides (IDPs), including anserine, carnosine, and balenine, are predominantly found in the skeletal muscles of vertebrates. Balenine is the major IDP in cetaceans. Serum amyloid A (SAA) is an acute phase protein released in response to damage or injury in various tissues, including skeletal muscles. A captive bottlenose dolphin (Tursiops truncatus) died due to rhabdomyolysis and subsequent acute kidney injury that probably originated from accidental muscle trauma. In this study, concentrations of IDPs and SAA were measured using stored serum collected from the affected dolphin with intermittent continuous damage of skeletal muscles to demonstrate the pathological relevance of these parameters and their usefulness as biomarkers for muscle damage in dolphins. The IDP concentration was measured using the high-performance liquid chromatography-ultraviolet method. The SAA concentration was measured using an enzyme-linked immunosorbent assay (ELISA) specific to dolphin SAA and a latex turbidimetric immunoassay (LTI) specific to human SAA. Herein, the IDP concentration was altered similarly to serum muscular enzymes, including creatinine kinase (CK) and aspartate aminotransferase (AST). However, IDP concentrations were elevated one day earlier than CK and AST levels at disease onset. Furthermore, IDP concentrations were similarly altered when assessed using both ELISA- and LTI-SAAs, and the change in IDP concentration coincided with that in LTI-SAA based on the statistical analysis. These data suggest that IDP concentration could detect muscle damage and injury, including necrosis and inflammation, in dolphins. Full article

At crime scenes, apart from the detection of blood, it may be important to determine whether a person was alive at the time of blood deposition. Based on the rapid onset of fibrinolysis after death, this pathway could be considered to identify potential biomarkers for postmortem blood. Fibrinolysis is the natural process that breaks down blood clots after healing a vascular injury. One of its products, D-dimer, could be a potential biomarker for postmortem blood. SERATEC^® (SERATEC^® GmbH, Göttingen, Germany) has developed the PMB immunochromatographic assay to simultaneously detect human hemoglobin and D-dimer. The main goals of this study were to assess the possibility of using this test to detect postmortem blood, evaluate D-dimer levels in antemortem, menstrual, and postmortem blood, and assess the ability to obtain STR profiles from postmortem blood. Except for one degraded sample, all postmortem blood samples reacted positively for the presence of D-dimer using the SERATEC^® PMB test. All antemortem blood samples from living individuals showed negative results for D-dimer detection, except for one liquid sample with a weak positive result, probably due to pre-existing health conditions. Menstrual blood samples gave variable results for D-dimer. The DIMERTEST^® Latex assay was used for semi-quantitative measurement of D-dimer concentrations, with postmortem and menstrual blood yielding higher D-dimer concentrations compared to antemortem blood. Full STR profiles were developed for all postmortem samples tested except for one degraded sample, pointing to the possibility of not only detecting postmortem blood at the crime scene but also the potential identification of the victim. Full article

E. coli attaches to, and forms biofilms on various surfaces, including latex and polystyrene, contributing to nosocomial spread. E. coli responds to both exogenous and endogenous insulin, which induces behavioral changes. Human insulin, a quorum signal surrogate for microbial insulin, may affect the ability of E. coli to interact with latex and polystyrene in the presence of various sugars. E. coli ATCC 25923 was grown in peptone (1%) yeast nitrogen base broth to either the logarithmic or stationary growth phase. Adherence to latex was determined using 6 × 6 mm latex squares placed in a suspension of washed cells (10³ CFU/mL; 30 min; 37 °C) in buffer containing insulin at 2, 20, and 200 µU/mL (Humulin^® R; Lilly) with and without mannose, galactose, fructose, sorbose, arabinose, xylose, lactose, maltose, melibiose, glucose-6-phosphate, glucose-1-phosphate, and glucosamine at concentrations reported to affect behavioral response. Attachment levels to latex were determined by the press plate method. Biofilm levels were measured in a similar fashion but with overnight cultures in flat bottom uncoated polystyrene plates. Controls were media, insulin, sugar, or buffer alone. Glucose served as the positive control. Overall, the stationary phase cells’ adherence to latex was greater, regardless of the test condition, than was measured for the logarithmic phase cells. The effect of insulin on adherence to latex was insulin and sugar concentration dependent. The addition of insulin (200 µU/mL) resulted in a significantly (p < 0.05) increased adherence to latex and biofilm formation on polystyrene compared with sugar alone for 12 of the 13 sugars tested with stationary phase bacteria and 10 of the 13 sugars tested with logarithmic phase bacteria. Adherence in response to sorbose was the only sugar tested that was unaffected by insulin. These findings show that insulin enhances E. coli’s association with materials in common usage in medical environments in a nutrition-dependent manner. Full article

Occupational exposure to commercial formic and acetic acids through dermal contact and inhalation during rubber sheet processing poses significant health risks to workers. Additionally, the use of these acids contributes to environmental pollution by contaminating water sources and soil. This study investigates the potential of three types of wood vinegar—derived from para-rubber wood, bamboo, and eucalyptus—obtained through biomass pyrolysis under anaerobic conditions, as sustainable alternatives to formic and acetic acids in the production of ribbed smoked sheets (RSSs). The organic constituents of each wood vinegar were characterized using gas chromatography and subsequently mixed with fresh natural latex to produce coagulated rubber sheets. The physical and chemical properties, equilibrium moisture content, and drying kinetics of the resulting sheets were then evaluated. The results indicated that wood vinegar derived from para-rubber wood contained a higher concentration of acetic acid compared to that obtained from bamboo and eucalyptus. As a result, rubber sheets coagulated with para-rubber wood and bamboo vinegars exhibited moisture sorption isotherms comparable to those of sheets coagulated with acetic acid, best described by the modified Henderson model. In contrast, sheets coagulated with eucalyptus-derived vinegar and formic acid followed the Oswin model. In terms of physical and chemical properties, extended drying times led to improved tensile strength in all samples. No statistically significant differences in tensile strength were observed between the experimental and reference samples. The concentration of acid was found to influence Mooney viscosity, the plasticity retention index (PRI), the thermogravimetric curve, and the overall coagulation process more significantly than the acid type. The drying kinetics of all five rubber sheet samples displayed similar trends, with the drying time decreasing in response to increases in drying temperature and airflow velocity. Full article

Natural rubber skim latex is commonly discarded as waste or turned into skim natural rubber products such as skim crepe and skim blocks. It is challenging to retrieve all residual rubbers in skim latex since it has a very low rubber content and many non-rubber components like protein. Manufacturers conventionally utilize concentrated sulfuric acid as a coagulant. This method generates many effluents and hazardous pollutants that negatively impact the environment. This work presents an innovative method for enhancing the skim latex’s value by employing an ultrafiltration membrane. This study aims to establish a hydrophilic PVDF-TiO₂ mixed-matrix membrane. The skim latex was processed through a membrane-based ultrafiltration process, which yielded two products: skim latex concentrate and skim serum. Skim latex deposits that cause fouling on the membrane surface can be identified by SEM-EDX and FTIR analysis. The PVDF–PVP-TiO₂ mixed-matrix membrane generated the maximum skim serum flux of 12.72 L/m²h in contrast to the PVDF pure membranes, which showed a lower flux of 8.14 L/m²h. CHNS analysis shows that a greater amount of nitrogen, which is indicative of the protein composition, was successfully extracted by the membrane separation process. These particles may adhere to the membrane surface during filtration, obstructing or decreasing the number of fluid flow channels. The deposition reduces the effective size of membrane pores, leading to a decline in flux rate. The hydrophilic PVDF-TiO₂ mixed-matrix membrane developed in this study shows strong potential for application in the latex industry, specifically for treating natural rubber skim latex, a challenging by-product known for its high fouling potential. This innovative ultrafiltration approach offers a promising method to enhance the value of skim latex by enabling more efficient separation and recovery. Full article

Currently, workers in the ribbed smoked sheet (RSS) rubber production industry face increasing health risks, primarily due to their direct involvement in converting fresh latex into raw rubber sheets. This process involves the manual addition of appropriately diluted commercial formic acid and acetic acid to induce coagulation, resulting in a tofu-like consistency, which is subsequently processed into rubber sheets. Previous studies have indicated that the use of commercial formic and acetic acids poses significant health hazards to workers and contributes to environmental pollution. Therefore, this study explores the feasibility of replacing commercial formic and acetic acids with wood vinegar derived from para-rubber wood, bamboo, and eucalyptus in the RSS production process. Wood vinegar samples from the three biomass sources were analyzed for their organic compound compositions using gas chromatography and subsequently used as coagulants in the preparation of raw rubber sheets. The drying kinetics and antifungal properties of the resulting sheets were then evaluated. The results revealed that wood vinegar derived from para-rubber wood contained the highest concentration of acetic acid (41.34%), followed by bamboo (38.19%) and eucalyptus (31.25%). Rubber sheets coagulated with wood vinegar from para-rubber wood and bamboo exhibited drying kinetics comparable to those obtained using acetic acid, with the two-term exponential model providing the best fit. Conversely, rubber sheets coagulated with eucalyptus-derived wood vinegar, which had a relatively high concentration of phenolic derivatives (22.08%), followed drying behavior consistent with the Midilli et al. model, similar to sheets treated with formic acid. In terms of antifungal properties, five fungal genera—Aspergillus, Penicillium, Fusarium, Trichoderma, and Paecilomyces—were identified on the rubber sheets. Fungal growth was most pronounced in the control samples (untreated with wood vinegar), whereas samples treated with wood vinegar exhibited significantly reduced fungal colonization. These findings indicate that wood vinegar is effective in inhibiting fungal growth on the surface of rubber sheets and may serve as a safer and more environmentally friendly alternative to commercial acid coagulants. Full article

The high-temperature rutting performance of asphalt mixtures is strongly dependent on the aggregate skeleton and particle movement under loading. Such mechanisms were addressed in the present study by a combined experimental and simulation approach based on the triaxial strength test. A single type of asphalt with two different aggregate gradations (dense and gap) was incorporated to highlight the role of gradation in resisting shear dilation. The simulation was carried out by coupling the discrete and finite element methods considering the realistic three-dimensional aggregate shapes and gradations as well as the flexible boundary prescribed by latex membranes as routinely employed in triaxial testing. In order to represent contact failure-induced cracks within the virtual specimens, the linear parallel bond model was mixed with the Burgers or linear model through random distribution at contacts involving the mortar units. Model verification was achieved by comparing the resulting stress–strain data against those from the laboratory. The calibrated model provided a platform for systematic investigation from the perspectives of particle movement, crack development and distribution, and interparticle contacts. The results showed that the gap-graded mixture yielded lower triaxial strengths and yet softened at a lower rate and exhibited smaller volumetric expansion in the post-peak region. A faster loss of internal cohesion was inferred in the dense-graded mixture based on the higher accumulation rate of cracks that were concentrated at the middle height towards the perimeter of the virtual specimen. Contact analysis indicated that aggregate skeleton was more influential in the strength and stability of gap-graded mixtures. Full article

Biomaterials interact with biological systems, influencing their responses. Different types of polymers—both natural and synthetic—are widely used in biomedical engineering, among a plethora of healthcare applications, to promote tissue regeneration. The natural rubber latex extracted from Hevea brasiliensis is a biopolymer that whose biocompatibility makes it a valuable study object. Its great regenerative properties are largely associated with the fraction FrHB1, which has demonstrated angiogenic and wound-healing potential by inducing blood vessel formation, collagen synthesis, and fibroblast migration—crucial factors for tissue repair. This study aimed to develop scalable methods for extracting and purifying the F1 protein fraction from industrialized natural latex for biomedical applications. We tested two types of industrial latex, bi-centrifuged and pre-vulcanized latex as well as 60% centrifuged natural latex to determine the most effective composition used in subsequent extractions and fractionation steps. Then, we isolated FrHB1 from the pre-vulcanized latex using selective precipitation, ultrafiltration, and affinity chromatography. The yield of the first batch of this serum was 40.62% with protein concentration of 1.52 ± 0.06 mg/mL. The second batch had a yield of 49.74%; however, due to results lying outside the analytical curve, its protein concentration could not be calculated. The yield of the third batch was 57.19%, and its protein concentration was 1.8477 ± 0.033 mg/mL. This approach facilitates large-scale therapeutic applications utilizing a commercially viable and accessible resource. Moreover, these findings highlight industrialized natural latex as a sustainable source of bioactive molecules, contributing to advancements in regenerative medicine and tissue engineering. Full article

The study of the fundamental principles of gelation of colloidal nanoparticles (NPs) advances the understanding of the formation of colloidal systems of living organisms. In this paper, the effect of particle size for a binary system of oppositely charged latexes on the experimental parameters of the system, including the gelation region, rheological parameters and cluster size, is considered for the first time. It is shown that the gelation regions in the phase diagrams for asymmetric particles are symmetric with respect to the ratio of charge and surface area of the particles. It was found that asymmetric particles form denser gels compared with the same concentration of symmetrical particles. This work provides insight into the gelation of asymmetric NPs, which is important for numerous applications, including their utilization in colloidal gels as ink for additive manufacturing and as scaffolds for cell growth, as well as understanding the fundamental aspects of the formation of bio-colloids. Full article

Direct ink writing (DIW) is an economical, straightforward, and relatively energy-efficient 3D printing technique that has been used in various domains. However, the utilization of rubber latex for DIW remains limited due to its high fluidity and inadequate support, which makes it challenging to meet the required ink rheological characteristics for DIW. In this study, a concentrated pre-vulcanized natural rubber latex (CPNRL) ink with a high solid content of 73% without additives is developed for DIW 3D printing. The CPNRL ink is concentrated using superabsorbent polymer (SAP) beads, which demonstrates good colloidal stability, favorable rheological properties, and superior printability. The impact of printing angles on the mechanical properties of the rubber specimens based on the CPNRL-73 ink is explored in detail, wherein the tensile strength of the specimen printed at a 90° angle reaches an impressive 26 MPa and a strain of approximately 800%, which surpasses the majority of 3D-printed rubber latex specimens. Additionally, the CPNRL ink can be used to print a wide range of intricate shapes, demonstrating its advantages in excellent formability. The preparation of 3D printable ink using the absorption method will expand the application of elastomers in fields such as customized flexible sensing and personalized rubber products. Full article

Ammonia is commonly used as a preservative in the production of concentrated natural rubber latex (CNRL) and latex products; however, it poses a serious risk to human health and the environment. In this study, we investigated a thioacetamide derivative (TD) as a preservative of ammonia-free CNRL and the optimization of a stabilization system comprising potassium hydroxide (KOH), lauric acid (LA), and sodium dodecyl sulfate (SDS) to enhance its preservation effect. The results revealed that an optimal amount of TD (0.03%) can effectively maintain the stability of CNRL, inhibit the increase in volatile fatty acid number (VFA number), maintain stable viscosity values, and improve the mechanical stability time (MST). However, increasing the TD dosage results in an increase in both the viscosity and VFA number and a decrease in MST. KOH was used to regulate the pH value of CNRL. It was also found that it can enhance considerably the mechanical properties of CNRL dry films and accelerates the vulcanization of vulcanized film; however, an excessive amount causes latex thickening. LA proved essential for improving the MST and reducing latex viscosity, thereby substantially enhancing the stability and processability of pre-vulcanized latex, but an excessive amount is detrimental to the curing speed and final mechanical strength. SDS can rapidly improve the MST and reduce the viscosity, but it negatively affects the surface molding of dry rubber films. In conclusion, KOH, LA, and SDS at appropriate dosages play a balancing and complementary role in the preparation of ammonia-free CNRL. Upon analyzing diverse performance metrics of CNRL, it has been determined that the optimal TD dosage ranges from 0.02 to 0.03% for maximum efficacy. The KOH dosage should be maintained within 0.1–0.15% to achieve the most favorable outcome, while the LA dosage is advisable to be kept between 0.06 and 0.1%. Full article

This study examined the feasibility of using natural rubber (NR) latex foam as a dye adsorbent and antibacterial foam. The dyes used in this experiment were Methylene Blue (MB) and Alizarin Yellow (AY). Foams with that optimum density were further evaluated for adsorption isotherm, kinetics, and thermodynamic data. The dye adsorption occurred in two steps: the initial and the stabilized stages where an increase in dye concentrations boosted the adsorption capacity. Based on the prediction, the maximum adsorptions of MB and AY from the solution were 3.15 and 10.31 mg/g, respectively. The Langmuir isotherm fits better with the adsorption of MB while AY is better matched by the Freundlich isotherm. Moreover, the adsorption behavior fits well with the pseudo-second-order model. MB took much longer to reach the stabilized stage, especially at high dye concentrations. The thermodynamic study revealed that physical adsorption accounted for most of the adsorption. Later, the foam after use as an adsorbent was further utilized as an antibacterial foam. Based on the qualitative and quantitative aspects, the results indicate that the dye-carrying foam could inhibit the growth of both Gram-positive and Gram-negative bacteria. It can be concluded that NR latex foam can be applied as a dye adsorbent and further utilized as an antibacterial foam. Full article