Search Results (23)

This study examines the mechanical properties of concrete in which natural aggregates are entirely replaced by modified basic oxygen furnace slag (MBOFS) and reinforced with chopped carbon fibers, under both dynamic and quasi-static loading conditions. The carbon fiber (CF) was subjected to heat treatment and pneumatic dispersion prior to mixing, and its performance was validated using thermogravimetric analysis (TGA) and single-fiber tensile tests. The experimental program included tests on workability, compressive strength, flexural strength, splitting tensile strength, impact resistance, and high strain rate behavior using the reverse split Hopkinson pressure bar (RSHPB) method. Thermogravimetric analysis (TGA) and scanning electron microscope (SEM) confirmed that heat treatment removed surface sizing from carbon fibers (CF) with minimal effect on tensile strength. Replacing natural aggregates with MBOFS reduced slump but enhanced compressive, flexural, and splitting tensile strength. Incorporating 1% chopped CF further improved mechanical performance: 6 mm CF increased compressive strength, while 12 mm CF enhanced flexural and splitting tensile strength. Impact resistance improved with CF addition, with 12 mm CF slightly outperforming 6 mm. RSHPB tests showed higher dynamic strength for 6 mm CF specimens, with both strength and dynamic increase factor rising with strain rate and gas pressure. Full article

In this paper, thermal and mechanical properties of ablative thermal protective material (TPM) as inhibitors for a free-standing propellant grain based on phenolic resin (PR) and acrylonitrile butadiene rubber (NBR) were investigated. NBR elastomerized PR composite, reinforced with chopped carbon fibers (CFs) (PR/NBR/CF), was prepared by homogenization of 90 parts by weight (PBW) PR in 100 PBW NBR (28 wt.% of acrylonitrile content). PR/NBR/CF composite was blended in two-roller open and closed mixers and in a twin-screw extruder. Carbon black, aluminum(III)-oxide, and fumed silica were added as promoters of thermal and mechanical properties of PR/NBR/CF. The structural analysis was studied using Fourier transform infrared spectroscopy (FT-IR). Thermal properties of the prepared PR/NBR/CF composite inhibitor were studied by ablation and firing tests, while a morphological analysis of the char layer formed after the ablation test was conducted via scanning electron microscopy (SEM). A low erosion rate of 2.00 × 10⁻⁴ m·s⁻¹ and high tensile strength and elongation at break of 6.7 MPa and 419.92%, respectively, indicate that the developed materials can be applied as a thermal insulation/inhibitor of free-standing rocket propellant grains. Bond strength between PR/NBR/CF composite and aluminized composite rocket propellant (ACRP), determined via a standard peel test, showed higher adhesion forces between the PR/NBR/CF composite and the ACRP compared to the cohesion between the ACRP molecular chains. Full article

This work aims at the determination of the coefficient of thermal expansion (CTE) of parts manufactured through the Fused Deposition Modeling process, employing fiber Bragg grating (FBG) sensors. Pure thermoplastic and composite specimens were built using different commercially available filament materials, including acrylonitrile butadiene styrene, polylactic acid, polyamide, polyether-block-amide (PEBA) and chopped carbon fiber-reinforced polyamide (CF-PA) composite. During the building process, the FBGs were embedded into the middle-plane of the test specimens, featuring 0° and 90° raster printing orientations. The samples were then subjected to thermal loading for measuring the thermally induced strains as a function of applied temperature and, consequently, the test samples’ CTE and glass transition temperature (T_g) based on the recorded FBG wavelengths. Additionally, the integrated FBGs were used for the characterization of the residual strain magnitudes both at the end of the 3D printing process and at the end of each of the two consecutively applied thermal cycles. The results indicate that, among all tested materials, the CF-PA/0° specimens exhibited the lowest CTE value of 14 × 10⁻⁶/°C. The PEBA material was proven to have the most isotropic thermal response for both examined raster orientations, 0° and 90°, with CTE values of 117 × 10⁻⁶/°C and 108 × 10⁻⁶/°C, respectively, while similar residual strains were also calculated in both printing orientations. It is presented that the followed FBG-based methodology is proven to be an excellent alternative experimental technique for the CTE characterization of materials used in 3D printing. Full article

The potential of RNA-based liquid biopsy is increasingly being recognized in diffuse large B-cell lymphoma (DLBCL), the most common subtype of non-Hodgkin’s lymphoma. This study explores the cell-free transcriptome in a humanized DLBCL patient-derived tumor xenograft (PDTX) model. Blood plasma samples (n = 171) derived from a DLBCL PDTX model, including 27 humanized (HIS) PDTX, 8 HIS non-PDTX, and 21 non-HIS PDTX non-obese diabetic (NOD)-scid IL2Rgnull (NSG) mice were collected during humanization, xenografting, treatment, and sacrifice. The mice were treated with either rituximab, cyclophosphamide, doxorubicin, vincristine, and prednisone (R-CHOP), CD20-targeted human IFNα2-based AcTaferon combined with CHOP (huCD20-Fc-AFN-CHOP), or phosphate-buffered saline (PBS). RNA was extracted using the miRNeasy serum/plasma kit and sequenced on the NovaSeq 6000 platform. RNA sequencing data of the formalin-fixed paraffin-embedded (FFPE) tissue and blood plasma samples of the original patient were included. Flow cytometry was performed on immune cells isolated from whole blood, spleen, and bone marrow. Bulk deconvolution was performed using the Tabula Sapiens v1 basis matrix. Both R-CHOP and huCD20-Fc-AFN-CHOP were able to control tumor growth in most mice. Xenograft tumor volume was strongly associated with circulating tumor RNA (ctRNA) concentration (p < 0.001, R = 0.89), as well as with the number of detected human genes (p < 0.001, R = 0.79). Abundance analysis identified tumor-specific biomarkers that were dynamically tracked during tumor growth or treatment. An 8-gene signature demonstrated high accuracy for assessing therapy response (AUC 0.92). The tumoral gene detectability in the ctRNA of the PDTX-derived plasma was associated with RNA abundance levels in the patient’s tumor tissue and blood plasma (p < 0.001), confirming that tumoral gene abundance contributes to the cell-free RNA (cfRNA) profile. Decomposing the transcriptome, however, revealed high inter- and intra-mouse variability, which was lower in the HIS PDTX mice, indicating an impact of human engraftment on the stability and profile of cfRNA. Immunochemotherapy resulted in B cell depletion, and tumor clearance was reflected by a decrease in the fraction of human CD45+ cells. Lastly, bulk deconvolution provided complementary biological insights into the composition of the tumor and circulating immune system. In conclusion, the blood plasma-derived transcriptome serves as a biomarker source in a preclinical PDTX model, enables the assessment of biological pathways, and enhances the understanding of cfRNA dynamics. Full article

The expansive utility of polymeric 3D-printing technologies and demand for high- performance lightweight structures has prompted the emergence of various carbon-reinforced polymer composite filaments. However, detailed characterization of the processing–microstructure–property relationships of these materials is still required to realize their full potential. In this study, acrylonitrile butadiene styrene (ABS) and two carbon-reinforced ABS variants, with either carbon nanotubes (CNT) or 5 wt.% chopped carbon fiber (CF), were designed in a bio-inspired honeycomb geometry. These structures were manufactured by fused filament fabrication (FFF) and investigated across a range of layer thicknesses and hexagonal (hex) sizes. Microscopy of material cross-sections was conducted to evaluate the relationship between print parameters and porosity. Analyses determined a trend of reduced porosity with lower print-layer heights and hex sizes compared to larger print-layer heights and hex sizes. Mechanical properties were evaluated through compression testing, with ABS specimens achieving higher compressive yield strength, while CNT-ABS achieved higher ultimate compressive strength due to the reduction in porosity and subsequent strengthening. A trend of decreasing strength with increasing hex size across all materials was supported by the negative correlation between porosity and increasing print-layer height and hex size. We elucidated the potential of honeycomb ABS, CNT-ABS, and ABS-5wt.% CF polymer composites for novel 3D-printed structures. These studies were supported by the development of a predictive classification and regression supervised machine learning model with 0.92 accuracy and a 0.96 coefficient of determination to help inform and guide design for targeted performance. Full article

Using fiber-reinforced polymer composite to replace metal in window frames has become a trend in aircraft manufacturing to achieve structural weight reduction. This study proposes an innovative winding compression molding process for continuous production of aircraft window frames using continuous carbon fiber-reinforced polyamide 6 thermoplastic composite filaments (CF/PA6). Through process parameter optimization, the production cycle of CF/PA6 composite window frames was controlled within 5 min, with an ultra-low porosity of 0.69%, meeting aviation application standards. Combining mechanical property experimental tests and finite element analysis, the mechanical performance of window frames made from three different materials was compared and evaluated. In the hoop direction, the mechanical performance of the continuous CF/PA6 thermoplastic window frames were significantly higher than that of chopped CF/epoxy compression molding window frames and aluminum alloy window frames. In the radial direction, the maximum strain occurred at the corner with the highest curvature of the frame due to the absence of fiber reinforcement, resulting in weak pure interlayer shear. Nevertheless, the thermoplastic CF/PA6 winding compression molded window frame still exhibited a high resistance to crack propagation and damage, as evidenced by the absence of any detectable sound of microdamage during testing with a 9000 N load. It is believed that achieving a further-balanced design of hoop–radial performance by appropriately introducing radial ply reinforcement can lead to a significant weight reduction goal in the window frame. The findings in this study provide an innovative process reference that can be universally applicable to high-speed and near-net-shape manufacturing without material waste of continuous fiber-reinforced thermoplastic composite products. Full article

Stereolithography (SLA) additive manufacturing is a method of manufacturing capable of generating complex geometric shapes with extremely high accuracy. Classic SLA uses UV curable resins, particularly polylactic acid (PLA), for part generation, but recent research has focused on utilizing this technology for the generation of various composite materials. There has been success in manufacturing composite materials using this technology, but little research has been performed on the generation of carbon-fiber-reinforced composite materials. Carbon fiber stereolithography (CF-SLA) is often overlooked due to carbon fiber’s natural inability to bond with PLA. To overcome this boundary, surface modification techniques were used on chopped carbon fibers to achieve greater bonding. Here, two modification techniques were explored: a sodium dodecyl sulfate (SDS) surfactant addition and nitric acid (HNO₃) etching. These methods were used to functionalize and prepare the surface of chopped carbon fiber (CF) for bonding with cured PLA resin. Treated fibers were dispersed in generic PLA resin, and tensile test specimens were printed for examining the reinforcement potential of the two treatment methods. Additional complexities arise during printing with fibers including fiber alignment, accumulation, and fiber fallout. To address these issues, a novel in-process mixing method was developed to maintain fiber dispersion. A two-level three-factor factorial design was performed for both treatment methods to determine optimal printing parameters. Through mechanical testing, atomic force microscopy, scanning electron microscopy, and contact angle measurements, the accompanying material property changes were characterized to further develop the field of fiber-reinforced liquid crystal display (LCD) additive manufacturing. After testing, it was found that composites created with SDS nanoparticle modification were stronger than both the acid etched fiber sample and plain PLA. Specifically, SDS surface treatment resulted in a 15% increase in modulus and maximum strength of the sample, mainly by enhancing the interlayer bonding between CF and PLA. Full article

Fused filament fabrication (FFF) is a popular additive manufacturing (AM) method for creating thermoplastic parts with intricate geometrical designs. Pure thermoplastic materials utilized in FFF, whose polymeric matrix is reinforced with other materials, such as carbon fibers (CFs), introduce products with advanced mechanical properties. However, since not all of these materials are biodegradable, the need for recycling and reuse immediately emerges to address the significant problem of how to dispose of their waste. The proposed study evaluates the printability, surface morphology and in vitro toxicity of two thermoplastic-based composite materials commonly used in wearable device manufacturing to provide enhanced properties and functionalities, making them suitable for various applications in the field of wearable devices. Tritan Copolyester TX1501 with 7.3% chopped CFs (cCFs) and Polyamide 12 (PA12) with 8.6%cCFs and 7.5% iron Magnetic Nanoparticles (MNPs)—Fe₄O₃ were used in the discrete ascending cycles of recycling, focusing on the surface quality performance optimization of the printed parts. Through stereoscopy evaluation, under-extrusion, and over-extrusion defects, as well as non-uniform material flow, are assessed in order to first investigate the influence of various process parameters’ application on the printing quality of each material and, second, to analyze the optimal value fluctuation of the printing parameters throughout the recycling cycles of the materials. The results indicate that after applying certain adjustments to the main printing parameter values, the examined recycled reinforced materials are still effectively 3D printed even after multiple cycles of recycling. A morphology examination using scanning electron microscope (SEM) revealed surface alterations, while a cytotoxicity assessment revealed the adverse effects of both materials in the form of cell viability and the release of proinflammatory cytokines in the cell culture medium. Full article

The development of high-temperature organic adhesive for bonding ultra-high-temperature ceramics with excellent thermal shock resistance has important significance to thermal protection systems for high-temperature environment application. In this study, high-temperature organic adhesive (HTOA) with carbon-fiber-SiC nanowires (CF-SiCNWs) binary phase enhancement structure was prepared. The method is that the SiCNWs grow on the chopped carbon-fiber surface and in the matrix of modified HTOA during high-temperature heat treatment with the help of a catalyst by a tip-growth way and with a vapor–liquid–solid (V-L-S) growth pattern. The results showed that the CF-SiCNWs binary phase enhancement structure plays a significant role in improving thermal shock resistance of high-temperature organic adhesive. The retention rate of the joint bond strength for the bonding samples after 20 cycles of thermal shock testing reaches 39.19%, which is higher than for the ones without CF, whose retain rate is only 6.78%. The shear strength of the samples with the CF-SiCNWs binary phase enhancement structure was about 10% higher than for those without the enhancement structure after 20 cycles of thermal shock. Full article

In the present study, how side-feeding of NiCF during twin-screw extrusion processing influences the fiber aspect ratio and thermal, mechanical, electrical, and electromagnetic properties of nickel-coated carbon fiber (NiCF)-reinforced polyamide 6 (PA6) composites was explored. For this, the fiber length distribution, thermal stability, heat deflection temperature, dynamic mechanical property, tensile, flexural, electrical resistivity, and electromagnetic interference shielding effectiveness (EMI SE) properties of NiCF/PA6 composites were extensively investigated. Chopped NiCF was regularly fed via either a main feeder or a side feeder and NiCF/PA6 pellets with different fiber-feeding pathways were prepared. The side-feeding effect of NiCF on the fiber length distribution and the composite properties was studied. The thermal stability, heat deflection temperature, storage modulus, tensile, flexural, and surface resistivity, and EMI SE properties of the NiCF/PA6 composites strongly depended not only on the NiCF content but also on the feeding method (main-feeding or side-feeding) upon extrusion processing, indicating that the fiber length distribution relevant to the fiber aspect ratio was critically important to enhance the composites’ properties. As a result, the NiCF/PA6 composites produced via side-feeding of NiCF exhibited an NiCF distribution longer than that produced via main-feeding, leading to enhancement of the thermal stability, heat deflection temperature, storage modulus, tensile, flexural, and EMI SE properties, strongly depending on the NiCF content. Full article

High-strength PI and PEI polymers differ by chemical structure and flexibility of the polymer chains that ensure lower cost and higher manufacturability of the latter. The choice of a particular polymer matrix is of actuality at design of antifriction composites on their basis. In this study, a comparative analysis of tribological behavior of PI and PEI- based composites was carried out with linear contact rubbing. The neat materials, as well as the two- and three-component composites reinforced with chopped carbon fibers, were investigated. The third components were typically used, but were different in nature (polymeric and crystalline) being solid lubricant fillers (PTFE, graphite and MoS₂) with characteristic dimensions of several microns. The variable parameters were both load and sliding speed, as well as the counterface material. It was shown that an improvement of the tribological properties could be achieved by the tribological layer formation, which protected their wear track surfaces from the cutting and plowing effects of asperities on the surfaces of the metal and ceramic counterparts. The tribological layers were not formed in both neat polymers, while disperse hardening by fractured CF was responsible for the tribological layer formation in both two- and three component PI- and PEI-based composites. The effect of polymer matrix in tribological behavior was mostly evident in two-component composites (PI/CF, PEI/CF) over the entire P⋅V product range, while extra loading with Gr and MoS₂ leveled the regularities of tribological layer formation, as well as the time variation in friction coefficients. Full article

Colocasia esculenta var. Aquatilis Hassk, elephant ear (CF-EE) has been widely used as traditional food and medicine. It also shows other therapeutic properties, such as antimicrobial and anti-cancer activity. In this study, we aim to investigate the effect of CF-EE extract on apoptosis induction associated with ER stress in cervical cancer HeLa cells. Cell viability was determined by MTT assay. Assessments of nuclear morphological changes, mitochondrial membrane potential, and intracellular reactive oxygen species (ROS) production were conducted by hoeshst33342, JC-1, and DCFH-DA fluorescence staining, respectively. Sub-G1 DNA content was analyzed by flow cytometry, and protein expression was determined by Western blotting. The results demonstrate that CF-EE extract suppressed HeLa cell growth and induced nuclear condensation and apoptotic bodies. There was also a loss of mitochondrial membrane potential and increased apoptosis marker protein expression, including Bax, cleaved-caspase-7, and cleaved-PARP. In addition, the results show that CF-EE extract induced ROS, increased ER stress proteins (GRP78 and CHOP), enhanced p38 and c-Jun phosphorylation, and inhibited Akt expression in HeLa cells. In summary, CF-EE extract induced apoptotic cell death-associated ROS-induced ER stress and the MAPK/AKT signaling pathway. Therefore, CF-EE extract has anticancer therapeutic potential for cervical cancer treatment in the future. Full article

In this study, graphene oxide (GO) was prepared by an improved Hummers’ method, and the graphene oxide–carbon fiber (GO-CF) hybrid fibers were prepared by electrophoretic deposition (EPD) with the above GO. The microstructure and mechanical properties of GO, CF and GO-CF cement matrix composites were studied by X-ray diffraction (XRD), SEM and mechanical tests. X-ray diffraction (XRD) and SEM results showed that the surface modification of CF with GO could effectively improve the dispersion of CF in the cement matrix, the template action of GO providing nucleation sites for cement hydration, which significantly enhanced the interface bond between CF and the cement matrix. The mechanical properties test results showed that the early compressive strength and flexural strength of cement matrix composites were significantly improved by GO. Adding CF into the cement matrix significantly improved the flexural strength, although the compressive strength was not improved, even exhibiting a downward trend when the CF content exceeded 0.5%. The flexural and compressive strength of GO-CF cement matrix composites were clearly improved, its 7 d flexural strength and compressive strength increased by 30.89% and 17.56%, respectively, and its 28 d flexural strength and compressive strength increased by 38.37% and 14.32%, respectively. The research results indicate that a new method was provided which used GO as a dispersant and surface modifier to improve the dispersion of chopped CF in a cement matrix, and the interaction between CF and the cement matrix interface could also be applied to the functional aspects of cement matrix composites. Full article

The article deals with the investigation of geopolymer foams (GFs) synthesized using by-products coming from the (i) screening-, (iv) pyrolysis-, (iii) dust abatement- and (iv) fusion-processes of the secondary aluminum industry. Based on principles of the circular economy to produce new technological materials, the experimental study involves industrial by-products management through the recovery, chemical neutralization, and incorporation of these relatively hazardous waste into the GFs. The geopolymeric matrix, consisting of metakaolin (MK) and silica sand (SA) with a 1:1 wt.% ratio, and chopped carbon fibers (CFs, 1 wt.% MK), was doped with the addition of different aluminum-rich industrial by-products with a percentage from 1 to 10 wt.% MK. The gas (mainly hydrogen) produced during the chemical neutralization of the by-products represents the foaming agents trapped in the geopolymeric structure. Several experimental tests were carried out to characterize the mechanical (flexural, compressive, and Charpy impact strengths) and thermal properties (thermal conductivity, and diffusivity, and specific heat) of the GFs. Results identify GFs with good mechanical and thermal insulation properties, encouraging future researchers to find the best combination (for types and proportions) of the different by-products of the secondary aluminum industry to produce lightweight geopolymer foams. The reuse of these industrial by-products, which according to European Regulations cannot be disposed of in the landfill, also brings together environmental sustainability and safe management of hazardous material in workplaces addressed to the development of new materials. Full article

A polyamide (PA) 12-based thermoplastic composite was modified with carbon nanotubes (CNTs), CNTs grafted onto chopped carbon fibers (CFs), and graphene nanoplatelets (GNPs) with CNTs to improve its thermal conductivity for application as a heat sink in electronic components. The carbon-based nanofillers were examined by SEM and Raman. The laser flash method was used to measure the thermal diffusivity in order to calculate the thermal conductivity. Electrical conductivity measurements were made using a Keithley 6517B electrometer in the 2-point mode. The composite structure was examined by SEM and micro-CT. PA12 with 15 wt% of GNPs and 1 wt% CNTs demonstrated the highest thermal conductivity, and its processability was investigated, utilizing sequential interdependence tests to evaluate the composite material behavior during fused filament fabrication (FFF) 3D printing processing. Through this assessment, selected printing parameters were investigated to determine the optimum parametric combination and processability window for the composite material, revealing that the selected composition meets the necessary criteria to be processable with FFF. Full article