Search Results (16)

Choline bromide (ChBr) has been less explored as an electrolyte material. This work demonstrates the promising potential of ChBr as a novel aqueous electrolyte for hybrid supercapacitors. At its optimized concentration of 3.5 M, ChBr solution exhibits a maximum conductivity of 79.56 mS cm⁻¹ at room temperature, along with a viscosity of 3.15 mPas and a density of 1.14 g cm⁻³. A reduction in water activity of the optimized ChBr electrolyte concentration extends the electrochemical stability window (ESW), enabling operation up to 1.9 V for two-electrode cells. When the current densities increase from 0.5 to 5 A g⁻¹, the hybrid supercapacitor based on ChBr electrolyte with the optimized mass ratio of electrodes composed of commercial microporous carbon (Maxsorb) demonstrates impressive specific energy and capacitance retention from 41 to 36 Wh kg⁻¹ and from 330 to 300 F g⁻¹ (per mass of one electrode), respectively. The experimental results obtained from this work demonstrate possibilities for further development and applications of ChBr-based hybrid systems in energy storage devices. Full article

The development of new materials for the controlled release of molecules represents a topic of primary importance in medicine, as well as in food science. In recent years, eutectic solvents have been applied as releasing media due to their improved capacity to interact with specific molecules, offering a broad range of tunability. Nevertheless, their application in essential oil dissolution are rare and more data are needed to develop new generations of effective systems. Herein, three eutectic systems, respectively, composed of choline chloride and ethylene glycol (1:2 molar ratio), methyltriphenylphosphonium bromide and ethylene glycol (molar ratio 1:5), and choline chloride and glycerol (molar ratio 1:1.5) were tested as materials for the controlled release of an essential oil derived from Citrus lemon leaves. Through static headspace fractionation, followed by gas chromatographic analysis, the performances of the three systems were assessed. The specific composition of DESs was pivotal in determining the releasing polar molecules as aldehydes and alcohols. A sustainability ranking based on the EcoScale tool highlighted the superior characteristics of the choline chloride–glycerol DES. Full article

Irritable Bowel syndrome (IBS) is a highly widespread gastrointestinal disorder whose symptomatology mainly affect the large intestine. Among the risk factors, psychosocial stress is the most acknowledged. The repeated water avoidance stress (rWAS) is considered an animal model of psychosocial stress that is capable of mimicking IBS. Otilonium bromide (OB), which is orally administered, concentrates in the large bowel and controls most of the IBS symptoms in humans. Several reports have shown that OB has multiple mechanisms of action and cellular targets. We investigated whether the application of rWAS to rats induced morphological and functional alterations of the cholinergic neurotransmission in the distal colon and whether OB prevented them. The results demonstrated that rWAS affects cholinergic neurotransmission by causing an increase in acid mucin secretion, in the amplitude of electrically evoked contractile responses, abolished by atropine, and in the number of myenteric neurons expressing choline acetyltransferase. OB counteracted these changes and also showed an intrinsic antimuscarinic effect on the post-synaptic muscular receptors. We assume that the rWAS consequences on the cholinergic system are linked to corticotrophin-releasing factor-1 (CRF1) receptor activation by the CRF hypothalamic hormone. OB, by interfering with the CFR/CRFr activation, interrupted the cascade events responsible for the changes affecting the rWAS rat colon. Full article

The common Deep Eutectic Solvent (DES) ‘ethaline’ (1:2 choline chloride:ethylene glycol) was examined here as a basis for the self-assembly of the surfactant dodecyltrimethylammonium bromide (C₁₂TAB). A phase diagram was constructed, showing evidence for a L₁ (micellar) phase, confirmed by tensiometry to have a room temperature critical micelle concentration (CMC) of 1.2 wt.%. Small angle neutron scattering (SANS) measurements indicate formation of interacting globular micelles with slightly smaller apparent radii than in water. The apparent mesophase/multiphase region was studied using SWAXS, demonstrating rich mesoscopic lyotropic liquid crystalline phase behaviour, with evidence for lamellar L_α peaks, alongside potential co-crystalline phases. We attempted to tailor the self-assembly by studying binary DES containing longer diols including 1,2-propanediol, 1,3-propanediol, 1,4-butanediol, and 1,5-pentanediol, and ternary DES where the HBD component was a 1:1 ethylene glycol:diol mixture. However, synchrotron SAXS showed that only ternary ‘propethaline’ mixtures displayed signs of self-assembly and micellization, perhaps due to the reduction in calculated Gordon parameter, which decreases linearly with increasing alkyl chain length. Systematic differences were thus observed in the ability of the solvents to modulate assembly, from globular micelles in ChCl:EG, to weaker assembly in long-tail DES, and complete solubilisation in butaline and pentaline. Full article

The Menshutkin reaction represents the alkylation of tertiary amines by alkyl halide where the reactants are neutral and the products, quaternary ammonium salts, are two ions with opposite signs. The most commonly used organic solvents in quaternization reactions are volatile organic solvents (VOSs), namely acetone, anhydrous benzene, dry dichloromethane (DCM), dimethylformamide (DMF) and acetonitrile (ACN). The purpose of this work was to examine eutectic solvents as a “greener” alternative to conventional solvents so that quaternization reactions take place in accordance with the principles of green chemistry. Herein, sixteen eutectic solvents were used as replacements for volatile organic ones in quaternization reactions of isonicotinamide with substituted phenacyl bromides. The reactions were carried out at 80 °C by three synthetic approaches: conventional (4–6 h), microwave (20 min) and ultrasound (3 h). Microwave-assisted organic reactions produced the highest yields, where in several reactions, the yield was almost quantitative. The most suitable eutectic solvents were based on choline chloride (ChCl) as the hydrogen bond acceptor (HBA) and glycerol, oxalic or levulinic acid as hydrogen bond donors (HBDs). The benefits of these three deep eutectic solvents (DESs) as a medium for quaternization reactions are the simplicity of their preparation for large-scale production, with inexpensive, available and nontoxic starting materials, as well as their biodegradability. Full article

This study was conducted to evaluate the protective effect of Juglans regia (walnut, Gimcheon 1ho cultivar, GC) on high-fat diet (HFD)-induced cognitive dysfunction in C57BL/6 mice. The main physiological compounds of GC were identified as pedunculagin/casuariin isomer, strictinin, tellimagrandin I, ellagic acid-O-pentoside, and ellagic acid were identified using UPLC Q-TOF/MS analysis. To evaluate the neuro-protective effect of GC, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT), 2′,7′-dichlorodihydrofluorecein diacetate (DCF-DA) analysis were conducted in H₂O₂ and high glucose-induced neuronal PC12 cells and hippocampal HT22 cells. GC presented significant cell viability and inhibition of reactive oxygen species (ROS) production. GC ameliorated behavioral and memory dysfunction through Y-maze, passive avoidance, and Morris water maze tests. In addition, GC reduced white adipose tissue (WAT), liver fat mass, and serum dyslipidemia. To assess the inhibitory effect of antioxidant system deficit, lipid peroxidation, ferric reducing antioxidant power (FRAP), and advanced glycation end products (AGEs) were conducted. Administration of GC protected the antioxidant damage against HFD-induced diabetic oxidative stress. To estimate the ameliorating effect of GC, acetylcholine (ACh) level, acetylcholinesterase (AChE) activity, and expression of AChE and choline acetyltransferase (ChAT) were conducted, and the supplements of GC suppressed the cholinergic system impairment. Furthermore, GC restored mitochondrial dysfunction by regulating the mitochondrial ROS production and mitochondrial membrane potential (MMP) levels in cerebral tissues. Finally, GC ameliorated cerebral damage by synergically regulating the protein expression of the JNK signaling and apoptosis pathway. These findings suggest that GC could provide a potential functional food source to improve diabetic cognitive deficits and neuronal impairments. Full article

The extraction of metals from waste printed circuit boards (WPCBs) with ionic liquids (ILs), Deep Eutectic Solvents (DESs) and organophosphorous-based acid (Cyanex 272) has been presented. The study was undertaken to assess the effectiveness of the application of the new leaching liquids, and the new method of extraction of metals from the leachate and the solid phase with or without the leaching process. Solvent extraction from the liquid leachate phase has been studied in detail with popular ILs, such as tetraoctylphosphonium bromide, {[P_8,8,8,8][Br] and tributyltetradecylphosphonium chloride, [P_4,4,4,14][Cl] using Aqueous Biphasic Systems (ABS) method. Trihexyltetradecylphosphonium bis(2,4,4-trimethylpentyl) phosphinate, [P_6,6,6,14][Cyanex272], ([P_6,6,6,14][BTMPP]), trihexyltetradecylphosphonium thiocyanate, [P_6,6,6,14][SCN], methyltrioctylammonium chloride (Aliquat 336), as well as bis(2,4,4-trimethylpentyl)phosphinic acid (Cyanex 272) were also used in the extraction of metals from the leachate. Two DESs (1) {choline chloride + lactic acid, 1:2} and (2) {choline chloride + malonic acid, 1:1} were used in the extraction of metals from the solid phase. The extraction behavior of metals with DESs was compared with that performed with three new bi-functional ILs: didecyldimethylammonium salicylate, [N_10,10,1,1][Sal], didecyldimethylammonium bis(2-ethylhexyl) phosphate, [N_10,10,1,1][D2EHPA], and didecyldimethylammonium bis(2,4,4-trimethylpentyl) phosphinate, [N_10,10,1,1][Cyanex272]. The [P_6,6,6,14][Cyanex272]/toluene and (Cyanex 272 + diethyl phosphite ester) mixtures exhibited a high extraction efficiency of about 50–90% for different metal ions from the leachate. High extraction efficiency of about 90–100 wt% with the ABS method using the mixture {[P_8,8,8,8][Br], or [P_4,4,4,14][Cl] + NaCl + H₂O₂ + post-leaching liquid phase} was obtained. The DES 2 revealed the efficiency of copper extraction, E_Cu = 15.8 wt% and silver, E_Ag = 20.1 wt% at pH = 5 from the solid phase after the thermal pre-treatment and acid leaching. The solid phase extraction efficiency after thermal pre-treatment only was (E_Cu = 9.6 wt% and E_Ag = 14.2 wt%). The use of new bi-functional ILs did not improve the efficiency of the extraction of metal ions from the solid phase. Process factors such as solvent concentration, extraction additives, stripping and leaching methods, temperature, pH and liquid/solid as well as organic/water ratios were under control. For all the systems, the selectivity and distribution ratios were described. The proposed extraction processes can represent alternative paths in new technologies for recovering metals from electronic secondary waste. Full article

Common solvents used for aromatic extraction from aliphatics typically degrade into toxic compounds, while green alternatives perform poorly compared to the state-of-the-art solvents. Deep eutectic solvents (DES) are a novel solvent type made of hydrogen bond donors (HBD) and hydrogen bond acceptors (HBA). DES have been applied in various applications, including advanced separations. In this study, DES were studied experimentally and using the Conductor-like Screening Model (COSMO) to separate benzene from cyclohexane as model compounds for an aromatic:aliphatic system. Both equilibrium and kinetic studies were performed to determine the liquid liquid equilibrium (LLE) and mass transfer rate for the DES-based separation. Selected HBAs including tetrabutylammonium bromide (N4444Br), tetrahexylammonium bromide (N6666Br), choline chloride (ChCl), and methyltriphenylphosphonium bromide (METPB) were paired with HBDs including ethylene glycol (EG) and glycerol (Gly). COSMO was used, with adjustments to reflect DES specific interactions, to predict the liquid-liquid equilibrium (LLE). COSMO results showed that ChCl and N6666Br-based DES extracted too little benzene or too much cyclohexane, respectively, to be considered for experimental evaluation. Overall, the COSMO model predictions for LLE of EG-based DES were very accurate, with root-mean-square deviations (RMSD) below 1% for both N4444Br:EG and METPB:EG. The glycerol systems were less accurately modeled, with RMSD’s of 4% for N4444Br:Gly and 6% for METPB:Gly. The lower accuracy of glycerol system predictions fmay be due to limitations in COSMO for handling glycerol’s influence on polarizability in the DES that is not seen in EG-based DES. Mass transfer kinetics were determined experimentally for DES and the results were fit to a first order kinetics model. METPB:Gly had the highest mass transfer coefficient at 0.180 min⁻¹, followed by N4444Br:EG at 0.143 min⁻¹. N4444Br:Gly and METPB:EG had the lowest mass transfer coefficients at 0.096 min⁻¹ and 0.084 min⁻¹, respectively. It was found that mass transfer rate was not directly related to maximum benzene solubility, as N4444Br:EG and METPB:Gly had the highest and lowest benzene removal, respectively, but had similar mass transfer coefficients. Full article

Deep eutectic solvents (DES) are compounds of a hydrogen bond donor (HBD) and a hydrogen bond acceptor (HBA) that contain a depressed melting point compared to their individual constituents. DES have been studied for their use as carbon capture media and biogas upgrading. However, contaminants’ presence in biogas might affect the carbon capture by DES. In this study, conductor-like screening model for real solvents (COSMO-RS) was used to determine the effect of temperature, pressure, and selective contaminants on five DES’ namely, choline chloride-urea, choline chloride-ethylene glycol, tetra butyl ammonium chloride-ethylene glycol, tetra butyl ammonium bromide-decanoic acid, and tetra octyl ammonium chloride-decanoic acid. Impurities studied in this paper are hydrogen sulfide, ammonia, water, nitrogen, octamethyltrisiloxane, and decamethylcyclopentasiloxane. At infinite dilution, CO₂ solubility dependence upon temperature in each DES was examined by means of Henry’s Law constants. Next, the systems were modeled from infinite dilution to equilibrium using the modified Raoults’ Law, where CO₂ solubility dependence upon pressure was examined. Finally, solubility of CO₂ and CH₄ in the various DES were explored with the presence of varying mole percent of selective contaminants. Among the parameters studied, it was found that the HBD of the solvent is the most determinant factor for the effectiveness of CO₂ solubility. Other factors affecting the solubility are alkyl chain length of the HBA, the associated halogen, and the resulting polarity of the DES. It was also found that choline chloride-urea is the most selective to CO₂, but has the lowest CO₂ solubility, and is the most polar among other solvents. On the other hand, tetraoctylammonium chloride-decanoic acid is the least selective, has the highest maximum CO₂ solubility, is the least polar, and is the least affected by its environment. Full article

The separation of benzene and cyclohexane azeotrope is one of the most challenging processes in the petrochemical industry. In this paper, deep eutectic solvents (DES) were used as solvents for the separation of benzene and cyclohexane. DES1 (1:2 mix of tetrabutylammonium bromide (TBAB) and levulinic acid (LA)), DES2 (1:2 mix of TBAB and ethylene glycol (EG)) and DES3 (1:2 mix of ChCl (choline chloride) and LA) were used as entrainers, and vapor-liquid equilibrium (VLE) measurements at atmospheric pressure revealed that a DES comprised of a 2:1 ratio of LA and TBAB could break this azeotrope with relative volatility (αij) up to 4.763. Correlation index suggested that the NRTL modelling approach fitted the experimental data very well. Mechanism of extractive distillation gained from FT-IR revealed that with hydrogen bonding and π–π bond interactions between levulinic acid and benzene could be responsible for the ability of this entrainer to break the azeotrope. Full article

The paper presents the preparation of new adsorbents based on silica gel (SiO₂) impregnated with deep eutectic solvents (DESs) to increase benzene, toluene, ethylbenzene, and p-xylene (BTEX) adsorption efficiency from gas streams. The DESs were synthesized by means of choline chloride, tetrapropylammonium bromide, levulinic acid, lactic acid, and phenol. The physico-chemical properties of new sorbent materials, including surface morphology and structures, as well as porosity, were studied by means of thermogravimetric analysis, Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction, and Brunauer–Emmett–Teller analysis. The effect of DESs type, flow rate, and initial concentration of BTEX were also investigated followed by regeneration and reusability of adsorbents. The results indicate that SiO₂ impregnated with tetrapropylammonium bromide and lactic acid in a 1:2 molar ratio have great potential for the removal of BTEX from gas streams. Its adsorption capacity was higher than the pure SiO₂ and other developed SiO₂-DES adsorbents. This result can be explained by the specific interaction between DESs and BTEX, i.e., hydrogen bonds interaction. Full article

UV–VIS spectroscopy analysis of six mixtures containing choline chloride or triphenylmethylphosphonium bromide as the hydrogen bond acceptor (HBA) and different hydrogen bond donors (HBDs, nickel sulphate, imidazole, d-glucose, ethylene glycol, and glycerol) allowed to determine the indirect and direct band-gap energies through the Tauc plot method. Band-gap energies were compared to those relative to known choline chloride-containing deep band-gap systems. The measurements reported here confirmed the tendency of alcohols or Lewis acids to increment band-gap energy when employed as HBDs. Indirect band-gap energy of 3.74 eV was obtained in the case of the triphenylmethylphosphonium bromide/ethylene glycol system, which represents the smallest transition energy ever reported to date for such kind of systems. Full article

In this study, CO₂ and SO₂ captures from post-combustion flue gas from a pulverized coal-fired power plant were evaluated using deep eutectic solvents (DES) to replace existing mono-ethanol amine (MEA) and CanSolv technologies. The system design of the DES-based CO₂ and SO₂ capture was based on the National Energy Technology Laboratory’s (NETL) 550 MWe pulverized coal-fired power plant model using Illinois #06 coal. Two of the most studied DES (choline chloride and urea at a 1:2 molar ratio and methyltriphenylphosphonium bromide (METPB) and ethylene glycol at a 1:3 molar ratio) for CO₂ and SO₂ capture were evaluated for this system analysis. Physical properties of DES were evaluated using both density functional theory (DFT)-based modeling as well as with documented properties from the literature. A technoeconomic assessment (TEA) was completed to assess DES ability to capture CO₂ and SO₂. Both solvents were able to fully dissolve and capture all SO₂ present in the flue gas. It was also found from the system analyses that choline chloride and urea outperformed METPB and ethylene glycol (had a lower final cost) when assessed at 10–30% CO₂ capture at high operating pressures (greater than 10 bar). At high system sizes (flow rate of greater than 50,000 kmoles DES per hour), choline chloride:urea was more cost effective than METPB:ethylene glycol. This study also establishes a modeling framework to evaluate future DES for physical absorption systems by both thermophysical and economic objectives. This framework can be used to greatly expedite DES candidate screening in future studies. Full article

A novel water-compatible molecularly imprinted resin was prepared in a green solvent deep eutectic solvent (DES). Resorcinol and melamine, as functional monomers with an abundant hydrophilic group, such as –OH, –NH₂ and –NH–, were introduced into the molecularly imprinted resin (MIR). Three DESs (choline chloride-ethylene glycol, tetramethylammonium bromide-ethylene glycol and tetramethylammonium chloride-ethylene glycol) were used to synthesize the molecularly imprinted resin and the resulting deep eutectic solvent-based molecularly imprinted resins were characterized by particle size analysis, elemental analysis, scanning electron microscopy, Fourier transform infrared spectroscopy and thermogravimetric analysis. The resulting deep eutectic solvent-based molecularly imprinted resins were then applied to the adsorption of quinolones (ofloxacin) in water. The adsorption process of deep eutectic solvent-based molecularly imprinted resin followed the static adsorption model, Langmuir isotherm (R² ≥ 0.9618) and kinetic model pseudo-second-order (R² > 0.9814). The highest theory adsorption ability of the three kinds of deep eutectic solvent-based molecularly imprinted resins was more than 23.79 mg/g. The choline chloride-ethylene glycol-based MIR was applied to solid-phase extraction for the determination and purification of quinolones (e.g., ciprofloxacin and ofloxacin). The detection limit of deep eutectic solvent-based molecularly imprinted resin-solid-phase extraction method was less than 0.018 mg/L. The recoveries of the deep eutectic solvent-based molecularly imprinted resin-solid-phase extraction method at three spiked levels were 88.7–94.5%, with a relative standard deviation of ≤4.8%. The novel deep eutectic solvent-based molecularly imprinted resin-solid-phase extraction method is a simple, selective and accurate pre-treatment method and can be used to determine the quinolones in environmental water. Full article

This work describes the synthesis of a series of quaternary ammonium salts and the assessment of their in vitro antileishmanial activity and cytotoxicity. A preliminary discussion on a structure-activity relationship of the compounds is also included. Three series of quaternary ammonium salts were prepared: (i) halomethylated quaternary ammonium salts (series I); (ii) non-halogenated quaternary ammonium salts (series II) and (iii) halomethylated choline analogs (series III). Assessments of their in vitro cytotoxicity in human promonocytic cells U-937 and antileishmanial activity in axenic amastigotes of L. (Viannia) panamensis (M/HOM/87/UA140-pIR-eGFP) were carried out using the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide) micromethod. Antileishmanial activity was also tested in intracellular amastigotes of L. (V) panamensis using flow cytometry. High toxicity for human U937 cells was found with most of the compounds, which exhibited Lethal Concentration 50 (LC₅₀) values in the range of 9 to 46 μg/mL. Most of the compounds evidenced antileishmanial activity. In axenic amastigotes, the antileishmanial activity varied from 14 to 57 μg/mL, while in intracellular amastigotes their activity varied from 17 to 50 μg/mL. N-Chloromethyl-N,N-dimethyl-N-(4,4-diphenylbut-3-en-1-yl)ammonium iodide (1a), N-iodomethyl-N,N-dimethyl-N-(4,4-diphenylbut-3-en-1-yl)ammonium iodide (2a), N,N,N-trimethyl-N-(4,4-diphenylbut-3-en-1-yl)ammonium iodide (3a) and N,N,N-trimethyl-N-(5,5-diphenylpent-4-en-1-yl)ammonium iodide (3b) turned out to be the most active compounds against intracellular amastigotes of L. (V) panamensis, with EC₅₀ values varying between 24.7 for compound 3b and 38.4 μg/mL for compound 1a. Thus, these compounds represents new “hits” in the development of leishmanicidal drugs. Full article