Search Results (40)

This paper presents a systematic qualification process for an electronic beam-steering antenna assembly for a low-Earth orbit (LEO) communication satellite. The transmitting/receiving antenna for the LEO communication satellite is based on a cavity-backed slot radiator, which has improved radiation efficiency and low mutual coupling compared to conventional PCB patch structures. In order to verify the electrical performance and reliability of the manual soldering process in a tightly spaced array structure with narrow element spacing and densely connected multi-channel RF modules, a reduced model was designed and fabricated and qualification tests were conducted under launch and on-orbit environments. The integration equipment was developed to ensure precise mechanical alignment and integration/disassembly between the radiating element arrays of the transmitting and receiving antenna modules and the RF modules, thereby establishing a manufacturability strategy for the antenna module and RF integrated module, which comprise a large array structure. Finally, the qualification tests of the transmitting and receiving antenna were performed to evaluate the structural and thermal stability considering the launch and orbital environments. The systematic qualification process proposed in this paper can be used in the development of the antenna system of the communication satellite. Full article

This paper presents a compact wide bandwidth, wide beamwidth circularly polarized (CP) antenna for satellite communication (SatCom) mobile terminals. The radiator is based on a cavity-backed crossed dipole, while a commercial quadrature power-divider/phase-shifter IC replaces conventional quarter-wavelength phase-delay lines to suppress dispersion-induced phase errors and maintain stable CP performance over a broad frequency range. To broaden the beam, a tightly coupled arc-shaped parasitic strip encircles the tapered semicircular arms, and the cavity cross-section is reduced to enhance lateral radiation. In addition, the cavity sidewalls are electrically connected to the parasitic element to increase the effective electrical length, downshift the operating frequency, and enable miniaturization. A prototype was fabricated and measured. The measured impedance bandwidth (IMBW, |S11| < −10 dB) is 1.76–3.08 GHz, fully covered by the AR < 3 dB bandwidth. The peak gain remains above 2 dBic over 1.7–3.1 GHz, while the half-power beamwidth (HPBW) stays around 114–142° and the 3 dB axial-ratio beamwidth (ARBW, AR < 3 dB) is around 114–144° across the entire operating band. These results indicate that the proposed antenna is a promising candidate for integrated multi-band SatCom terminals requiring wide bandwidth operation and wide-angle coverage. Full article

A novel wideband 1-bit reconfigurable transmitarray (RTA) is proposed, which is based on a substrate-integrated cavity-backed patch (SCIBP) element. The RTA element consists of a pair of SCIBP antennas, achieving wideband operational capability through the optimization of dielectric substrate thickness. To suppress surface-wave propagation between adjacent RTA elements, a substrate-integrated waveguide (SIW) is designed to function as a metallic isolation wall. A 180° phase shift is realized by dynamically manipulating p-i-n diodes embedded within the SCIBP antenna structure. When the dielectric substrate thickness is increased from 6 mm to 10 mm, the 3 dB transmission bandwidth is expanded from 10% to 33.6%. The simulation results confirm that the proposed element realizes a 3 dB transmission bandwidth of 33.6%. A prototype RTA with 100 elements is designed, fabricated, and measured. The prototype achieves a peak gain of 16.6 dBi at 4.6 GHz, accompanied by an aperture efficiency of 17.2% and a 3 dB gain bandwidth of 18.9%. Furthermore, measured scanned beams illustrate that the proposed RTA possesses good beamscanning performance. Owing to its many advantages, such as wideband operation, lightweight design, low cost, simple structure, and easy fabrication, it is particularly suitable for application in intelligent communication systems and radar systems. Full article

A self-diplexing, full-mode, substrate-integrated waveguide (SIW) rectangular cavity-backed antenna based on an inverted Z-shaped radiating slot with filtering characteristics is investigated in this work. The proposed design allows for individual control through the loading of four different slots, namely, a combination of horizontal and diagonal slots, called inverted Z-shaped slots. The two diagonal slots make 45° angles between them, and this flexible rotation gives the design flexibility regarding control of the bands. By combining these slots into a modified inverted Z-shaped slot, a SIW rectangular cavity is configured and energized with two separate 50 Ω microstrip feed lines to resonate at two different frequencies—11.63 GHz and 13.27 GHz—and TE₂₁₀ and TE₂₂₀ modes are obtained for X- and Ku-band wireless purposes. In an experimental analysis, reflection coefficients of S₁₁ < −10 dB were noted for both operating frequencies of 7.4% (11.23–12.09 GHz) and 3.0% (13.15–13.55 GHz), respectively. The average gain of the proposed antenna design in the two different operating conditions is 6.14 and 6.16 dBi, respectively. In addition, the proposed self-diplexing antenna attained high isolation, greater than 28 dB between both operating channels, and showed overall measured efficiency of 87.32%. Moreover, it features a single-layer structure, operates in dual bands, provides broadside linear polarization, and exhibits filtering capabilities. Full article

As wireless systems evolve toward multiband, multifunctional convergence and high-throughput services, the demand for ultra-wideband circularly polarized (CP) antennas for multi-standard terrestrial–satellite terminals continues to grow; however, because of the dispersive nature of the three-quarter-ring phase shifter, the relative bandwidth achievable with conventional crossed-dipole antennas rarely exceeds 100%. This paper presents a compact left-hand circularly polarized (LHCP) crossed-dipole antenna that combines a cavity-backed ground, ground-slot perturbations, and parasitic patches to simultaneously broaden the impedance and axial-ratio bandwidths. The fabricated prototype achieves an impedance bandwidth (IMBW) of 0.71–3.89 GHz (138%) and a 3 dB axial-ratio bandwidth (ARBW) of 0.98–3.27 GHz (108%), while maintaining gains above 3.5 dBic across most of the frequency range. The good agreement validates the multi-technique co-design and shows that the compact architecture (0.302 λ × 0.302 λ × 0.129 λ) breaks classical crossed-dipole limits. The antenna provides a scalable building block for wideband conformal arrays in next-generation integrated GNSS–SatCom systems. Full article

This paper presents a wideband circularly polarized (CP) substrate-integrated waveguide (SIW) cavity-backed slot antenna array arranged in a 2 × 2 configuration with differential feeding structures. The design features arc-shaped microstrips within the SIW cavity to excite the ${\mathrm{TE}}_{011}^x$/${\mathrm{TE}}_{101}^y$ and ${\mathrm{TE}}_{211}^y$/${\mathrm{TE}}_{121}^x$ modes. By overlapping the center frequencies of the two modes, wideband CP radiation is achieved. The introduction of four modified ring couplers composes a simple but efficient differential feeding network, eliminating the need for balanced resistors like baluns, making it more suitable for millimeter wave or even higher frequency applications. Experimental results show that the antenna array achieves a −10 dB impedance bandwidth of 32.6% (from 17.28 to 24.00 GHz), a 3 dB axial ratio (AR) bandwidth of 13.8% (from 17.05 to 19.57 GHz), a 3 dB gain bandwidth of 41.8% (from 15.39 to 23.51 GHz) and a peak gain of 10.6 dBi, with results closely matching simulation data. This study enhances the development of differential CP SIW cavity-backed slot antenna arrays, offering a potential solution for creating compact integrated front-end circuits in the millimeter wave or Terahertz frequency range. Full article

This work presents a novel dual-polarized antenna array tailored for Internet of Things (IoT) applications, specifically designed to operate in the millimeter-wave (mm-wave) spectrum within the frequency range of 30–60 GHz. Leveraging printed ridge gap waveguide (PRGW) technology, the antenna ensures robust performance by eliminating parasitic radiation from the feed network, thus significantly enhancing the reliability and efficiency required by IoT communication systems, particularly for smart cities, autonomous vehicles, and high-speed sensor networks. The proposed antenna achieves superior radiation characteristics through a cross-shaped magneto-electric (ME) dipole backed by an artificial magnetic conductor (AMC) cavity and electromagnetic bandgap (EBG) structures. These features suppress surface waves, reduce edge diffraction, and minimize back-lobe emissions, enabling stable, high-quality IoT connectivity. The antenna demonstrates a wide impedance bandwidth of 24% centered at 30 GHz and exceptional isolation exceeding 40 dB, ensuring interference-free dual-polarized operation crucial for densely populated IoT environments. Fabrication and testing validate the design, consistently achieving a gain of approximately 13.88 dBi across the operational bandwidth. The antenna’s performance effectively addresses the critical requirements of emerging IoT systems, including ultra-high data throughput, reduced latency, and robust wireless connectivity, essential for real-time applications such as healthcare monitoring, vehicular communication, and smart infrastructure. Full article

In this paper, a wideband OAM antenna array for wireless communication is proposed, which has a wide impedance bandwidth and can cover the S-C band with a relative bandwidth of 61.58%. The measured gain can reach 7.81 dBi and the radiation efficiency can reach 74.7%. Compared with similar antennas, the antenna array has a metal back cavity as the supporting structure, which further improves the structural stability of the array. The array adopts Z-shaped parasitic radiation units, a ring-shaped stepped metal reflection back cavity, and other structures. These can be verified to improve the performance of the array after design analysis and testing. In addition, the performance enhancement of a conventional Wilkinson divider by adding the S-shaped parasitic radiation patch is analysed by parameter scanning. The array is robust, simple to process, and easy to integrate. It can maximise its value in the crowded retrofit space of wireless antennas. Full article

To enhance the capability of a ground penetrating radar (GPR) in subsurface target identification and improve its polarization sensitivity in detecting underground linear objects, a circularly polarized broadband composite spiral antenna was designed. This antenna integrates equiangular spiral and Archimedean spiral structures, achieving a wideband coverage of 1–5 GHz with stable circular polarization characteristics. The antenna employs an exponentially tapered microstrip balun for impedance matching and a metallic-backed cavity filled with absorbing materials to enhance its directivity. Experimental results demonstrate excellent radiation performance and stable circular polarization characteristics, with the axial ratio consistently below 3 dB throughout the operating frequency band, highlighting its suitability for polarimetric GPR systems. Furthermore, a 3D GPR measurement using the designed antenna validates its improved capacity for detecting subsurface linear objects, compared to the conventional linearly polarized bowtie antenna. Full article

Magneto-electric dipole (ME-dipole) antennas offer several advantages, including wide impedance bandwidth, stable high gain, unidirectional radiation, and low back-lobe radiation patterns, making them suitable for modern wireless communication systems. However, the thickness of conventional ME-dipole antennas is typically about a quarter wavelength (0.25${\lambda }_o$) at the center operating frequency, which may not be desirable for portable device applications. This work introduces a new feeding method that reduces the antenna profile and ground plane size while maintaining the same advantages. A suspended horizontal line is proposed to excite the cavity-less ME-dipole antenna through proximity coupling. The measured results demonstrate a wide impedance bandwidth of 45.3% (ranging from 2.05 GHz to 3.25 GHz) and an average in-band gain of 9 dBi with stable $\pm 1$ dBi in-band variation with a ground reflector of size about 0.89${\lambda }_o^2$. More importantly, the cavity-less design reduces the overall thickness of the antenna to 0.17${\lambda }_o$ at the center operating frequency. Full article

A compact and wideband beamforming antenna array based on a substrate-integrated coaxial line (SICL) Butler matrix at 60 GHz is proposed in this paper. The cavity-backed patch antenna loading double-ridged horn antenna is designed to enhance a gain of 5.4 dB and a bandwidth of 2.7 GHz. Different phase centers of double-ridged horn elements are formed into a non-uniform array to reduce sidelobes by −7.9 dB. By introducing the defected ground structure (DGS) for a broadband coupler, a rotationally symmetric SICL Butler matrix is designed with a 55–70 GHz bandwidth and compact dimensions of 63 × 65 × 0.512 mm³. To validate the design, a prototype was fabricated and measured. The experimental results show a wideband −10 dB impedance bandwidth of 23.3% (55.4–70 GHz) with measured gains ranging from 15 to 16.1 dBi at 62 GHz. The one-dimensional beam scanning covers ±32°. The simulation and measurement results are in good agreement. Full article

Wearable communication technologies necessitate antenna designs that harmonize ergonomic compatibility, reliable performance, and minimal interaction with human tissues. However, high specific absorption rate (SAR) levels, limited radiation efficiency, and challenges in integration with flexible materials have significantly constrained widespread deployment. To address these limitations, this manuscript introduces a novel wearable cavity-backed substrate-integrated waveguide (SIW) antenna augmented with artificial magnetic conductor (AMC) structures. The proposed architecture is meticulously engineered using diverse textile substrates, including cotton, jeans, and jute, to synergistically integrate SIW and AMC technologies, mitigating body-induced performance degradation while ensuring safety and high radiation efficiency. The proposed design demonstrates significant performance enhancements, achieving SAR reductions to 0.672 W/kg on the spine and 0.341 W/kg on the forelimb for the cotton substrate. Furthermore, the AMC-backed implementation attains ultra-low reflection coefficients, as low as −26.56 dB, alongside a gain improvement of up to 1.37 dB, culminating in a total gain of 7.09 dBi. The impedance bandwidth exceeds the ISM band specifications, spanning 150 MHz (2.3–2.45 GHz). The design maintains remarkable resilience and operational stability under varying conditions, including dynamic bending and proximity to human body models. By substantially suppressing back radiation, enhancing directional gain, and preserving impedance matching, the AMC integration optimally adapts the antenna to body-centric communication scenarios. This study uniquely investigates the dielectric and mechanical properties of textile substrates within the AMC-SIW configuration, emphasizing their practicality for wearable applications. This research sets a precedent for wearable antenna innovation, achieving an unprecedented balance of flexibility, safety, and electromagnetic performance while establishing a foundation for next-generation wearable systems. Full article

A dual-band (K-/Ka-band) antenna array is presented. An ultra-wideband antenna element in the shape of a double-ridged waveguide is used as a radiation slot, and a novel dual-periodic ridge gap waveguide (RGW) with an interdigital-pin bed of nails (serving as a filter) is used to realize dual-band operation. By periodically arranging the pins of two different heights in two dimensions, the proposed RGW with interdigital-pin bed of nails is able to realize and flexibly adjust two passbands. The widely used GW-based back cavity boosts the realized gain and simplifies the feed network design. A 4 × 4 prototype array was designed, fabricated, and measured. The results show that the array has two operating bands at 24.5–26.4 GHz and 30.3–31.5 GHz, and the realized gain can reach 19.2 dBi and 20.4 dBi, respectively. Meanwhile, there is a very significant gain attenuation at stopband. Full article

Herein, we present new design principles for gain enhancement and cross-polarization suppression in dual-polarized cavity-backed antennas and demonstrate the capability in an octagonal cavity-backed open prism antenna (OCROP). In our approach, the gain is enhanced through an optimal flaring procedure and a novel metallic iris is used to control the electromagnetic fields and thereby reduce the cross-polarization. Previously, we investigated a dual-polarized OCROP antenna configuration and were able to simultaneously achieve 50% impedance bandwidth, 40% cross-polarization bandwidth (≤25 dB), and 10.2 dBi peak gain. In this study, we investigated gain enhancement by flaring an upper section of the ground cavity sidewalls, while maintaining a constant cavity height. Two cases were investigated: (1) the flare angle was modified, while the ratio of the non-flared to flared sidewall heights was kept constant, and (2) the ratio of the non-flared to flared sidewall heights was varied. In case 1, we established that, while increasing the flare angle results in a gain increase, there is a limit, as cross-polarization at the upper operating frequencies increases. In case 2, we were able to reduce the aperture phase error and achieve a higher peak gain of 12.8 dBi. To address the increased cross-polarization at the high frequency end when a large flare was used, we added a metallic iris at the junction of non-flared and flared sidewalls. We showed that increasing the iris width generally decreases the cross-polarization at high frequencies, without compromising the gain and impedance bandwidth. At an optimal width, it provides a nearly constant, low cross-polarization (below −25.8 dB) and a peak gain of 13.3 dBi, across the entire 50.7% impedance bandwidth of the antenna. We fabricated and successfully tested a prototype to verify the design and simulation approach. These results prove that incorporating an aperture flare with a metallic iris can significantly improve the gain and cross-polarization performance of cavity-backed antennas. Full article

This article presents the methodology to design a single-fed circularly-polarized antenna with low front-to-back ratio (FBR). A circular-patch (CPatch) antenna has been incorporated within the rectangular-cavity, made of, substrate integrated waveguide (SIW). The size of the CPatch and the SIW cavity has been chosen appropriately, in a manner, that the both resonators dominant mode coincide. This arrangement has been adopted to realize the basic radiating unit with no surface-wave and the significantly lower FBR. The circularly polarization has been excited through shorting the periphery of CPatch radiator to the “one of the two metallic grounds” of this SIW cavity. The patch periphery has been shorted from two distinct points, separated by the quarter wavelength—over center frequency of working band. The antenna has been designed and manufactured over Rogers RT/Duroid 5880 substrate with dielectric constant (ε_r) of 2.2, loss-tangent (tan δ, at 10 GHz) of 0.0009, and substrate height of 0.508 mm. Southwest^® end launcher (SEL) along with SIW-to-GCPW (Grounded Co-Planar Waveguide) transition has been used here to facilitate the measurement of antenna’s electrical and the radiation performance. The designed antenna’s impedance bandwidth and the 3 dB axial-ratio (AR) bandwidth is 9.5% and the 2.3%, respectively. It’s simulated and the measured peak gain, within working frequency band, is higher than 8.5dBic. The proposed antenna’s FBR is antenna is significantly lower than the conventional circularly-polarized antennas. Through comparative study, with work in open literature, it has been demonstrated that the designed antenna, based on proposed method, can a potential candidate for applicable in satellite and in the other spaceborne communication system’s module—at ground and in the space station. Full article