Search Results (25)

The primary challenge associated with stainless steel in fuel cell operation is its susceptibility to corrosion, which leads to increased contact resistance and subsequent degradation of electrochemical performance. In general, the protective layers have been loaded onto the metal surface by widely used traditional techniques such as physical vapor deposition (PVD), or cathode arc ion plating. However, the above sputtering and evaporation ways require a high-vacuum condition, complicated experimental setups, higher costs, and an elevated temperature. Therefore, herein the achievement for uniform coatings over a large surface area has been realized by using a cost-effective strategy through a complete wet chemical process. The synergistic regulation of two conductive components and a plastic additive has been employed together with the entrapment of a surfactant to optimize the microstructure of the coating surface. The assembly of layered graphite and a polystyrene sphere could maintain both the high corrosion resistance feature and excellent electrical conductivity. In particular, the intrinsic vacant space in the above physical barriers has been filled with fine powders of indium tin oxide (ITO) due to its small size, and the interconnected conductive network with vertical/horizontal directions would be formed. All the key technical targets based on the U.S. Department of Energy (DOE) have been achieved under the simulated operating environments of a proton exchange membrane fuel cell. The corrosion current density has been measured as low as 0.52 μA/cm² (for the sample of graphite/mixed layer) over the applied potentials from −0.6 V to 1.2 V and its protective efficiency is evaluated to be 99.8%. The interfacial contact resistance between the sample and the carbon paper is much less than 10 mΩ·cm² (3.4 mΩ·cm²) under a contact pressure of 165 N/cm². The wettability has been investigated and its contact angle has been evolved from 48° (uncoated sample) to even 110°, providing superior hydrophobicity to prevent water penetration. Such an innovative approach opens up new possibilities for improving the durability and reducing the costs of carbon-based coatings. Full article

The present study reports the tribological properties and residual stress of titanium chromium nitride (TiCrN) coatings. Thin films of TiCrN were deposited on tungsten carbide substrates at 400 °C in a vacuum of 5 × 10⁻⁶ mbar using the cathodic-arc physical vapor deposition technique with chromium variation. X-ray diffraction (XRD) spectroscopy was employed to probe the structures of the deposited thin films. The phase constituent was found to gradually shift from cubic TiN to cubic CrN. Both the hardness and elastic modulus of the sheet changed from 29.7 to 30.9 GPa and 446 to 495 GPa, respectively. The biaxial compressive residual stress after an initial absolute scan in the range of 30–100° was determined using XRD (d-sin²ψ method). These mechanical and tribological properties of films were investigated with the help of instrumented nanoindentation and a ball-on-disk tribometer wear test. The wear test indicates that the TiCrN thin film, featuring a Cr/Ti ratio of 0.587, exhibits superior wear resistance and maximum compressive residual stress in comparison to other thin films. Full article

The effect of the spatial arrangement in the physical vapor deposition (PVD) chamber on the composition and properties of coatings is considered using the example of the deposition of the (Ti,Al)N coating. The proposed method is one of the ways (along with varying the arc current of the cathodes and the bias voltage, as well as using alloy cathodes) to change the ratio of elements in the coating, and achieves this across a wide range of values. The three samples were located, respectively, opposite the evaporator with a titanium cathode, opposite the evaporator with an aluminum cathode and in an intermediate position between the two evaporators. The coating was deposited without rotating the turntable. The aluminum content in the coatings decreases from 94.2 at.% for the sample located directly opposite the evaporator with an Al cathode to 10.3 at.% for the sample located opposite the evaporator with a Ti cathode. In the coating deposited on the sample located opposite the aluminum cathode, the formation of a nitrided layer with a thickness of about 250 nm was observed in the substrate. The maximum hardness (32.3 ± 1.7 GPa) belongs to a coating on the sample occupying an intermediate position. The coating on the sample located opposite the aluminum cathode has a hardness of 16.7 ± 0.8 GPa. The coating hardness on the sample located opposite the titanium cathode is 28.5 ± 1.1 GPa. The best fracture strength in the scratch test was observed for the coating on the sample occupying an intermediate position. The nature of the coating fracture in the scratch test was studied. A sufficiently high-quality coating can be obtained without rotating the turntable, and the coating composition can be controlled by changing the position of the sample relative to the evaporators. Full article

In this work, a comparative study of the tribological performance of two hard coatings, CrN/TiBN, was conducted for research purposes and industrial applications in food products, particularly for food packaging into cans using the double hermetic sealing process. CrN and TiBN coatings were successfully deposited on a base-cobalt metal substrate of a CoCrW commercial alloy using physical vapor deposition by arc evaporation (AEPVD) technology to improve the tribological properties of the commercial alloy, including wear and corrosion resistance, lower coefficient of friction, and overall durability. This research focuses on conducting scratch and abrasion wear resistance tests in dry conditions; specifically, it pursues to evaluate the wear corrosion properties, known as tribocorrosion performance, on CrN/TiBN hard coatings. The experimental results show that the CrN coating (2.9 μm) is slightly thicker than the TiBN coating (2.7 μm), with a 47 N critical load. It also shows a lower coefficient of friction (CoF) in a dry environment, while the TiBN coating showed total detachment and a high coefficient of friction in a dry environment condition. Tribocorrosion testing in brine aqueous solution indicated that CrN coating shows a high friction coefficient with a higher open circuit potential value (E_corr), and TiBN shows the lowest corrosion potential (E_corr) and the lowest friction coefficient. This suggests that CrN could provide better corrosion protection for commercial cobalt alloys and improve tool performance during the food canning process in brine environments. Full article

Fabrication aspects of PdO thin films and coatings are reviewed here. The work provides and organizes the up-to-date information on the methods to obtain the films. In recent years, the interest in Pd oxide for different applications has increased. Since Pd can be converted into PdO, it is instructive to pay attention to the preparation of the pure and the alloyed Pd films, heterostructures, and nanoparticles synthesized on different substrates. The development of PdO films is presented from the early reports on coatings’ formation by oxidation of Pd foils and wires to present technologies. Modern synthesis/growth routes are gathered into chemical and physical categories. Chemical methods include hydrothermal, electrochemical, electroless deposition, and coating methods, such as impregnation, precipitation, screen printing, ink jet printing, spin or dip coating, chemical vapor deposition (CVD), and atomic layer deposition (ALD), while the physical ones include sputtering and cathodic arc deposition, laser ablation, ion or electron beam-induced deposition, evaporation, and supersonic cluster beam deposition. Analysis of publications indicates that many as-deposited Pd or Pd-oxide films are granular, with a high variety of morphologies and properties targeting very different applications, and they are grown on different substrates. We note that a comparative assessment of the challenges and quality among different films for a specific application is generally missing and, in some cases, it is difficult to make a distinction between a film and a randomly oriented, powder-like (granular), thin compact material. Textured or epitaxial films of Pd or PdO are rare and, if orientation is observed, in most cases, it is obtained accidentally. Some practical details and challenges of Pd oxidation toward PdO and some specific issues concerning application of films are also presented. Full article

Monolayer (CrN, AlTiN) and bilayer (CrN/AlTiN) coatings are formed on the surface of conventional heat-treated and gas-nitrided X45CrMoV5-3-1 tool steel via Cathodic Arc Physical Vapor Deposition (CAPVD), and the adhesion characteristics and room- and high-temperature wear behavior of the coatings are compared with those of the un-nitrided ones. Scratch tests on the coatings show that the bilayer coating exhibits better adhesion behavior compared to monolayer ones, and the adhesion is further increased in all coatings due to the high load carrying capacity of the diffusion layer formed by the nitriding process. Dry friction tests performed at room temperature reveal that, among ceramic-based coatings, the coating system with a high adhesion has the lowest specific wear rate (0.06 × 10⁻⁶ mm³/N·m), and not only the surface hardness but also the nitriding process is important for reducing this rate. Studies on wear surfaces indicate that the bilayer coating structure has a tendency to remove the surface over a longer period of time. Hot wear tests performed at a temperature (450 °C) corresponding to aluminum extrusion conditions show that high friction coefficient values (>1) are reached due to aluminum transfer from the counterpart material to the surface and failure develops through droplet delamination. Adhesion and tribological tests indicate that the best performance among the systems studied belongs to the steel–CrN/AlTiN system and this performance can be further increased via the nitriding process. Full article

Plasma generation by cathodic arc spots plays a crucial role for coating processes that make use of the Arc-PVD technology. Usually, the arc spot motion over the cathode is steered by a magnetic field of a particular distribution and magnitude to ensure a continuous plasma generation, the avoidance of liquid droplets, and a proper utilization of cathode material by homogeneous erosion. This study presents a semi-empirical model that allows for an examination and characterization of the arc spot motion with regard to direction and speed as a function of an imposed magnetic field. This model considers the different components of random walk, retrograde, and Robson drift motion. Introduced empirical coefficients were determined by corresponding experimental investigations. The calibrated model describes the arc spot motion in good agreement to the recorded spot tracks and can therefore be applied for an evaluation of different magnetic field configurations. Full article

In this work, the diamond-like carbon and titanium nitride (DLC/TiN) multilayer coatings were prepared on a cemented tungsten carbide substrate (WC—3 wt.% Co) using the cathodic vacuum arc physical vapor deposition (Arc-PVD) method and pulsed Arc-PVD method with a graphite cathode for the deposition of TiN and carbon layers, respectively. The structural and mechanical properties of the prepared coatings were studied, and different techniques, such as scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Raman spectroscopy, and microindentation techniques investigated their microstructure, composition, and phases. The prepared coatings had a multilayer structure with distinct phases of DLC, TiN, and carbide substrate. The potentiodynamic polarization method (PDP) was performed for the DLC/TiN multilayer coatings in 3% NaCl solution to evaluate the corrosion resistance of the prepared coatings. It has been shown that the DLC layer provided the coating with a polarization resistance of 564.46 kΩ. Moreover, it has been demonstrated that the DLC/TiN coatings had a high hardness of 38.7–40.4 GPa, which can help to extend the wood-cutting tools’ life. Full article

In this study, heat-treated and multisurface engineered DIN 1.2367 tool steel was subjected to room and elevated temperature wear tests, and the effect of nitriding on its tribological behavior was investigated. CrN, AlTiN, and CrN/AlTiN coatings with a total thickness of 2 µm were obtained by arc cathodic physical vapor deposition on conventional heat-treated and gas-nitrided steels. The white layer formed during nitriding was removed, and a diffusion layer (100 µm) was achieved in the cross section of the steel having a tempered martensitic matrix. The highest surface hardness was attained with an integral coating (CrN/AlTiN), and surface hardness increased even more after nitriding due to the formation of a multicomponent ceramic layer on top of the diffusion layer. The room temperature wear tests performed against an alumina counterpart revealed that (i) CrN/AlTiN-coated steel had the highest friction coefficient of 0.26, which further increased to 0.33 by nitriding due to the increase in shear strength, and that (ii) with increasing surface hardness, the specific wear rates (W) of the heat-treated and coated steels could be ranked as follows: W_CrN/AlTiN < W_AlTiN < W_CrN. The wear rates decreased when nitriding was carried out prior to coating. In order to simulate the aluminum extrusion conditions, hot wear behavior of the surfaces against AA6080 alloy at 450 °C was investigated. The hot wear tests revealed that (i) high friction coefficients were reached due to the adhesive characteristic of aluminum to the surfaces, (ii) the nitrided and CrN/AlTiN-coated sample exhibited the lowest wear rate among all studied surfaces, and (iii) the film damage on the worn surfaces mostly occurred in the form of droplet delamination. Full article

Moving components of industrial machines and tools are subjected to wear and friction. This reduces their useful life and efficiency in running conditions, particularly at high temperatures. One of the most popular solutions is to apply an appropriate surface coating to the tribocouple’s base materials. In this study, tribometer experiments were used to evaluate the tribological performance of cathodic arc physical vapor deposited (CAPVD) AlCrN, TiSiN, CrTiN, and ZrN coatings on the gas nitrided AISI H13 tool steel to explore the effects of nitriding the steel on wear and friction behavior of these coatings at ambient and elevated temperatures. The coatings characterization is split into three main parts: mechanical, morphological, and chemical characterization. Nanoindentation has been used for mechanical characterization, thin film X-ray diffraction (XRD), and an energy-dispersive X-ray spectrometer mounted on a scanning electron microscope for chemical characterization, optical profilometer, and atomic force microscopy (AFM) for morphological characterization. Significant improvements in the adhesion qualities of the coatings to the substrate were achieved as a result of nitration. Due to this circumstance, the coatings’ load-bearing capacity and high-temperature wear resistance ratings were enhanced. The wear results showed that the AISI H13 tool steel nitriding with AlCrN and ZrN layers decreased wear rates by two to three times at 700 °C. Full article

A titanium (Ti) commercial cathode material and high purity Ar and O₂ were used in the cathodic arc physical vapor deposition (arc-PVD) process. The TiO_x coating was deposited on the three sets of Raschig rings using decreasing ratios of Ar/O₂:440/60, 400/100 and 300/100. The cross sections of the TiO_x PVD coating were analyzed using field emission scanning electron microscopy (FE-SEM), X-ray energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). A homogeneous layer of Ti with small O content was observed, and the data suggest that a thin TiO_x oxide film was deposited. For this reason, a thermal treatment was applied to the coating to oxidize it and form the rutile phase of TiO₂ in the coating, which was demonstrated by grazing incidence XRD. In addition, the TiO_x coatings absorb radiation, which was observed by diffuse reflectance band gap energy measurement. Silver (Ag) was added by the photo-reduction method, using UVC light to activate the TiO₂ coating, and the band gap energy was analyzed by diffuse reflectance. The photocatalytic activities of the films were evaluated by degradation of the model dye rhodamine B and in the removal of fecal coliforms using two matrices, water from a secondary treatment effluent, and synthetic water. Full article

This paper describes a physical vapor deposition (PVD) coating equipment, as well as the according deposition parameters suitable to provide hard nitride coatings on broaches up to a length of 2.2 m. The octagonal-shaped vacuum chamber reached a height of 4.5 m and a diameter of 1.2 m. To explore a sufficient and reproducible film, an adhesion test sample and tools were subjected to a pretreatment in a Cr²⁺ Ar⁺ high-power impulse magnetron sputtering (HIPIMS) plasma prior to the actual film deposition. Two deposition methods were applied: reactive unbalanced magnetron (UBM) sputtering was introduced to deposit TiAlN-based coatings from Ti50Al50 2.5 m long targets. Alternatively, multilayer coatings were generated by reactive simultaneous UBM sputtering from Ti50Al50 and TiAl6V4 targets, respectively, and chromium targets utilizing high-power impulse magnetron sputtering (HIPIMS) technology. In the latter case, three cathodes were furnished with 0.9 m long targets lined up upon each other. A segmented UBM cathode design was described to meet economic deposition if varying tool sample lots in the deferring workpiece lengths have to be handled in industrial practice. The resulting (TiAl/Cr)N multilayer coatings attained typical hardness values of HV 2800 and an adhesion measured by critical load up to 50 N. The cutting performance of this coating was evaluated by simulated shaping tests over a test length of 210 m on C 45 steel. The (TiAlV/Cr)N showed an improved wear behavior by factor of 2 to 3 compared to TiN deposited by cathodic arc operated in an industrial PVD coater. A real comparison was undertaken, applied to a 1.3 m long model broach. (TiAl/Cr)N showed a prolongation in industrial lifetime by 150% compared to TiN. Full article

Due to the increased demands for drilling and cutting tools working at extreme machining conditions, protective coatings are extensively utilized to prolong the tool life and eliminate the need for lubricants. The present work reports on the effect of a second MeN (Me = Zr, Cr, Mo, Nb) layer in WN-based nanocomposite multilayers on microstructure, phase composition, and mechanical and tribological properties. The WN/MoN multilayers have not been studied yet, and cathodic-arc physical vapor deposition (CA-PVD) has been used to fabricate studied coating systems for the first time. Moreover, first-principles calculations were performed to gain more insight into the properties of deposited multilayers. Two types of coating microstructure with different kinds of lattices were observed: (i) face-centered cubic (fcc) on fcc-W₂N (WN/CrN and WN/ZrN) and (ii) a combination of hexagonal and fcc on fcc-W₂N (WN/MoN and WN/NbN). Among the four studied systems, the WN/NbN had superior properties: the lowest specific wear rate (1.7 × 10⁻⁶ mm³/Nm) and high hardness (36 GPa) and plasticity index H/E (0.93). Low surface roughness, high elastic strain to failure, Nb₂O₅ and WO₃ tribofilms forming during sliding, ductile behavior of NbN, and nanocomposite structure contributed to high tribological performance. The results indicated the suitability of WN/NbN as a protective coating operating in challenging conditions. Full article

The primary objective of this study was to investigate and compare the surface topography of hard coatings deposited by three different physical vapor deposition methods (PVD): low-voltage electron beam evaporation, unbalanced magnetron sputtering and cathodic arc evaporation. In these deposition systems, various ion etching techniques were applied for substrate cleaning. The paper summarizes our experience and the expertise gained during many years of development of PVD hard coatings for the protection of tools and machine components. Surface topography was investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), scanning transmission electron microscopy (STEM) and 3D stylus profilometry. Observed similarities and differences among samples deposited by various deposition methods are discussed and correlated with substrate material selection, substrate pretreatment and deposition conditions. Large variations in the surface topography were observed between selected deposition techniques, both after ion etching and deposition processes. The main features and implications of surface cleaning by ion etching are discussed and the physical phenomena involved in this process are reviewed. During a given deposition run as well as from one run to another, a large spatial variation of etching rates was observed due to the difference in substrate geometry and batching configurations. Variations related to the specific substrate rotation (i.e., temporal variations in the etching and deposition) were also observed. The etching efficiency can be explained by the influence of different process parameters, such as substrate-to-source orientation and distance, shadowing and electric field effects. The surface roughness of PVD coatings mainly originates from growth defects (droplets, nodular defects, pinholes, craters, etc.). We briefly describe the causes of their formation. Full article

Hard coatings, such as AlTiN-TiSiN, deposited by Physical Vapor Deposition (PVD) techniques are widely used in industrial applications to protect and increase the lifetime of industrial components, such as cutting tools, dies, and forming tools. Despite their great properties, such as high hardness and wear and oxidation resistance, they are limited in cases of severe conditions due to the poor adhesion between the coating and the substrate. Duplex treatments have commonly been used to improve the adhesive properties of PVD coatings, especially those of the cathodic arc evaporation type. The purpose of this study is to achieve coatings with the good properties of the Magnetron Sputtering processes but with higher adhesion than that achieved with these techniques, thus achieving coatings that can be used under the most severe conditions. In this work, an AlTiN-TiSiN coating was deposited by a combination of DC Magnetron Sputtering (DCMS) and High-Power Impulse Magnetron Sputtering (HiPIMS) after a gas nitriding pretreatment on 1.2379 and Vanadis 4 tool steels. Mechanical (ultra-microhardness and scratch tests) and tribological tests were carried out to study the improvement in the properties of the coating. Duplex-treated samples showed improved adhesion between the coating and the substrate, with second critical load (Lc2) values greater than 100 N. Furthermore, they showed great toughness and wear resistance. These results show that this type of coating technique could be used in the most extreme applications and that they can compete with other techniques and coatings that to date they have not been able to compete with. Full article