Search Results (266)

Electrochromic devices (ECDs) capable of modulating both visible color and infrared (IR) emissivity are promising for applications in smart thermal camouflage and multifunctional displays. However, conventional transmissive ECDs suffer from limited IR modulation due to the low IR transmittance of transparent electrodes. Here, we report a reflection-type electrochromic zinc-ion battery (HWEC-ZIB) using a self-doped polyaniline nanorod film (SP(ANI-MA)) as the active layer. By positioning the active material at the device surface, this structure avoids interference from transparent electrodes and enables broadband and efficient IR emissivity tuning. To prevent electrolyte-induced IR absorption, a thermal lamination encapsulation method is employed. The optimized device achieves emissivity modulation ranges of 0.28 (3–5 μm) and 0.19 (8–14 μm), delivering excellent thermal camouflage performance. It also exhibits a visible color change from earthy yellow to deep green, suitable for various natural environments. In addition, the HWEC-ZIB shows a high areal capacity of 72.15 mAh cm⁻² at 0.1 mA cm⁻² and maintains 80% capacity after 5000 cycles, demonstrating outstanding electrochemical stability. This work offers a versatile device platform integrating IR stealth, visual camouflage, and energy storage, providing a promising solution for next-generation adaptive camouflage and defense-oriented electronics. Full article

As the core device for protecting the safety of the pressure-bearing system, the spring full-open safety valve is prone to various forms of valve seat sealing surface damage after long-term opening and closing impact, corrosion, and medium erosion, which may lead to internal leakage. In view of the problems that the high-frequency acoustic emission signal of the internal leakage of the safety valve has, namely, a large number of energy-overlapping areas in the frequency domain, the overall signal presents broadband characteristics, large noise content, and no obvious time–frequency characteristics. A composite denoising method, IWTD, improved wavelet threshold function with dual adjustable factors, and the improved VMD algorithm is proposed. In view of the problem that the optimal values of the dual adjustment factors a and b of the function are difficult to determine manually, an improved dung beetle optimization algorithm is proposed, with the maximum Pearson coefficient as the optimization target; the optimization is performed within the value range of the dual adjustable factors a and b, so as to obtain the optimal value. In view of the problem that the key parameters K and α in VMD decomposition are difficult to determine manually, the maximum Pearson coefficient is taken as the optimization target, and the improved dung beetle algorithm is used to optimize within the value range of K and α, so as to obtain the IVMD algorithm. Based on the IVMD algorithm, the characteristic decomposition of the internal leakage acoustic emission signal occurs after the denoising of the IWTD function is performed to further improve the denoising effect. The results show that the Pearson coefficients of all types of internal leakage acoustic emission signals after IWTD-IVMD composite noise reduction are greater than 0.9, which is much higher than traditional noise reduction methods such as soft and hard threshold functions. Therefore, the IWTD-IVMD composite noise reduction method can extract more main features out of the measured spring full-open safety valve internal leakage acoustic emission signals, and has a good noise reduction effect. Feature recognition after noise reduction can provide a good evaluation for the safe operation of the safety valve. Full article

This study presents a comprehensive investigation of acoustic emission (AE) characteristics for condition monitoring of rolling bearings in passenger ropeway systems. Through controlled laboratory experiments and field validation across multiple operational ropeways, we establish an optimized AE-based diagnostic framework. Key findings demonstrate that resonant VS150-RIC sensors outperform broadband sensors in defect detection, showing greater energy response at characteristic frequencies for inner race defects. The RMS parameter emerges as a robust diagnostic indicator, with defective bearings exhibiting periodic peaks and higher mean RMS values. Field tests reveal progressive RMS escalation preceding visible damage, enabling predictive maintenance. Furthermore, we develop a novel Paligemma LLM model for automated wear detection using AE time-domain images. The research validates the AE technology’s superiority over conventional vibration methods for low-speed bearing monitoring, providing a scientifically grounded approach for safety-critical ropeway maintenance. Full article

Background: Glioblastoma (GBM) resists current therapies due to its rapid proliferation, diffuse invasion, and heterogeneous cell populations. We previously showed that a single cold atmospheric plasma discharge tube (DT) reduces GBM viability via broad-spectrum electromagnetic (EM) emissions. Here, we tested whether two DTs arranged in a helmet configuration could generate overlapping EM fields to amplify the anti-tumor effects without thermal injury. Methods: The physical outputs of the single- and dual-DT setups were characterized by infrared thermography, broadband EM field probes, and oscilloscope analysis. Human U87-MG cells were exposed under the single or dual configurations. The viability was quantified with WST-8 assays mapped across 96-well plates; the intracellular reactive oxygen species (ROS), membrane integrity, apoptosis, and mitochondrial potential were assessed by multiparametric flow cytometry. Our additivity models compared the predicted versus observed dual-DT cytotoxicity. Results: The dual-DT operation produced constructive EM interference, elevating electric and magnetic field amplitudes over a broader area than either tube alone, while temperatures remained <39 °C. The single-DT exposure lowered the cell viability by ~40%; the dual-DT treatment reduced the viability by ~60%, exceeding the additive predictions. The regions of greatest cytotoxicity co-localized with the zones of highest EM field overlap. The dual-DT exposure doubled the intracellular ROS compared with single-DT and Annexin V positivity, confirming oxidative stress-driven cell death. The out-of-phase operation of the discharge tubes enabled the localized control of the treatment regions, which can guide future treatment planning. Conclusions: Two synchronously operated plasma discharge tubes synergistically enhanced GBM cell killing through non-thermal mechanisms that coupled intensified overlapping EM fields with elevated oxidative stress. This positions modular multi-DT arrays as a potential non-invasive adjunct or alternative to existing electric-field-based therapies for glioblastoma. Full article

Lithium (Li)-rich continental brines found in the Lithium Triangle region in South America are a natural resource of paramount importance. In the present research, the analytical performance of laser-induced breakdown spectroscopy (LIBS) technology was assessed for the quantitative analysis of Li in natural brines aimed at enhancing the efficient exploration of salt flats (called salars). Brine samples were collected from different salars located in the Puna plateau (Northwest Argentina) and analyzed by LIBS in the form of solid pressed pellets. Broadband emission spectra (180–900 nm) were recorded and spectrally analyzed by specially designed computational algorithms. The laser-induced plasmas were characterized by calculating the electron density and the temperature. The Li elemental concentrations in the brines were determined through univariate calibration with the Li I emission line at 670.77 nm by using a suitable set of standards with Li concentrations up to 1300 $\mathsf{\mu }$g/g. The calculated limit of detection was LoD = 0.2 ± 0.1 $\mathsf{\mu }$g/g. The Li content in the brines determined with LIBS showed a good agreement (normalized standard deviation: σ_N = 25%) with the concentrations measured with atomic absorption spectroscopy. The results demonstrated the feasibility of the LIBS technique for the quantitative analysis of Li in natural brines, thus contributing to advancing the exploration of Li-rich resources. Full article

Photothermal conversion is a pivotal energy transformation mechanism in solar energy systems. Achieving high-efficiency and broadband photothermal conversion within the solar radiation spectrum holds strategic significance in driving the innovative development of renewable energy technologies. In this study, a transmission matrix method was employed to design an interference-type solar selective absorber based on multilayer Cr-SiO₂ planar films, successfully achieving an average absorption of 94% throughout the entire solar spectral range. Further analysis indicates that this newly designed absorber shows excellent absorption performance even at a relatively large incident angle (up to 60°). Additionally, the newly designed absorber demonstrates lower polarization sensitivity, enabling efficient operation under complicated incident conditions. With its simple fabrication process and ease of preparation, the proposed absorber holds substantial potential for applications in photothermal conversion fields such as solar thermal collectors. Full article

Herein, we study a method for developing a broad-emission emitter that can emit radiation from the visible light to NIR regions. Firstly, an NIR phosphor’s optical properties (e.g., scattering vs. weight concentration, conversion efficiency, and emission spectra under blue and red light excitation) are investigated. Then, pcW-LEDs encapsulated with NIR down-conversion phosphor samples are prepared to test these optical properties. The results show that pcW-LEDs encapsulated with the NIR phosphor at different weight concentrations of 10.0%, 12.5%, and 15.5%, respectively, emit a broadband emission from 400 nm to 900 nm. The EQE values of the pcW-LEDs encapsulated with NIR phosphor at weight concentrations of 10%, 12.5%, and 15.0% are 26%, 23%, and 19%, respectively. The correlated color temperatures of these samples are 5767 K, 5940 K, and 6068 K, respectively. The obtained radiant fluxes of the samples are 26 mW, 22 mW, and 18 mW, respectively, at an injection current of 50 mA. Full article

With the increasing energy consumption of buildings, transparent heat mirror films have been widely used in building windows to enhance energy efficiency owing to their excellent spectrally selective properties. Previous studies have typically focused on spectral selectivity in the visible and near-infrared bands, as well as single-parameter optimization of film materials or thickness, without fully exploring the performance potential of the films. To address the limitations of traditional design methods, this paper proposes a deep reinforcement learning-based approach that employs an adaptive strategy network to optimize the thin-film material system and layer thickness parameters simultaneously. Through inverse design, a Ta₂O₅/Ag/Ta₂O₅/Ag/Ta₂O₅ (42 nm/22 nm/79 nm/22 nm/40 nm) thin-film structure with broadband spectral selectivity was obtained. The film exhibited an average reflectance of 75.5% in the ultraviolet band and 93.2% in the near-infrared band while maintaining an average visible transmittance of 87.0% and a mid- to far-infrared emissivity as low as 1.7%. Additionally, the film maintained excellent optical performance over a wide range of incident angles, making it suitable for use in complex lighting environments. Building energy simulations indicate that the film achieves a maximum energy-saving rate of 17.93% under the hot climatic conditions of Changsha and 16.81% in Guangzhou, demonstrating that the designed transparent heat mirror film provides a viable approach to reducing building energy consumption and holds significant potential for practical applications. Full article

Biodiversity monitoring requires the discovery of multi-target tracking. The main requirement is not to reduce the localization error but the continuity of the tracks: a high ratio between the duration of the track and the lifetime of the target. To this end, we present an algorithm for detecting and tracking mobile underwater targets that utilizes reflections from active acoustic emission of broadband signals received by a rigid hydrophone array. The method overcomes the problem of a high false alarm rate by applying a tracking approach to the sequence of received reflections. A 2D time–distance matrix is created for the reflections received from each transmitted probe signal by performing delay and sum beamforming and pulse compression. The result is filtered by a 2D constant false alarm rate (CFAR) detector to identify reflection patterns that correspond to potential targets. Closely spaced signals for multiple probe transmissions are combined into blobs to avoid multiple detections of a single target. The position and velocity are estimated using the debiased converted measurement Kalman filter. The results are analyzed for simulated scenarios and for experiments in the Adriatic Sea, where six Global Positioning System (GPS)-tagged gilt-head seabream fish were released and tracked by a dedicated autonomous float system. Compared to four recent benchmark methods, the results show favorable tracking continuity and accuracy that is robust to the choice of detection threshold. Full article

Incorporating lead (Pb) into the germanium (Ge) lattice emerges as a promising approach for bandgap engineering, enabling luminescence at longer wavelengths and paving the way for enhanced applications in short-wave infrared (SWIR) light sources and photodetectors. In this work, we report on optical properties of GePb alloys fabricated by a complementary metal-oxide semiconductor (CMOS)-compatible process that includes Pb ion implantation followed by solid-phase epitaxial regrowth via flash-lamp annealing. Optical characterization, including photoluminescence spectroscopy and Fourier-transform infrared reflectance spectroscopy, reveals that GePb alloys exhibit a reduced bandgap compared to pure Ge, resulting in longer-wavelength emission, while also providing broadband antireflective properties below 1800 nm wavelengths due to the surface subwavelength nanostructure. These findings position nanostructured GePb as a highly promising candidate for SWIR optoelectronic applications. Full article

Bi-doped glasses and fibers have been widely applied in solid-state and fiber lasers. However, the mechanism underlying near-infrared (NIR) luminescence remains unclear, and Bi-related luminescence centers (BLCs) are prone to alteration during fiber fabrication, making it challenging to achieve high-performance Bi-doped glass fibers. In this work, Bi-, Bi-Al-, and Bi-Ge-doped silica glasses were investigated to elucidate the origin of NIR luminescence. Two broad NIR fluorescence bands were observed in silica glasses, originating from distinct BLCs. The longer-wavelength fluorescence band at 1423 nm, demonstrating sensitivity to Bi doping concentration and homogeneity, is attributed to Bi clusters (aggregates of Bi⁺ ions), whereas the shorter-wavelength emission, independent of Bi concentration, originates from isolated Bi⁺ ions. A vacuum-assisted melting-in-tube method with a single-step heating process was employed to fabricate Bi-doped silica-based glasses and fibers. The fluorescence bands of the fibers remained consistent with those of the precursor glasses, indicating no new BLCs were formed during fiber fabrication. The modulation of fluorescence bands was primarily governed by Bi cluster formation. Suppressing Bi clustering through co-doping with Al/Ge or optimizing fabrication conditions offers an effective route to tailor the fluorescence properties of Bi-doped glasses and fibers. Full article

Integrated light-emitting diodes (LEDs) with waveguides play an important role in applications such as augmented reality (AR) displays, particularly regarding coupling efficiency optimization. Quantum dot light-emitting diodes (QLEDs), an emerging high-performance optoelectronic device, demonstrate substantial potential for next-generation display technologies. This study investigates the influence of microcavity modulation on the output of QLEDs coupled with a silicon nitride (SiNx) waveguide by simulating a white light QLED (W-QLED) with a broad spectrum and mixed RGB QDs (RGB-QLED) with a comparatively narrower spectrum. The microcavity converts both W-QLED and RGB-QLED emissions from broadband white-light emissions into narrowband single-wavelength outputs. Specifically, both of them have demonstrated wavelength tuning and full-width at half-maximum (FWHM) narrowing across the visible spectrum from 400 nm to 750 nm due to the microcavity modulation. The resulting RGB-QLED achieves a FWHM of 11.24 nm and reaches 110.76% of the National Television System Committee 1953 (NTSC 1953) standard color gamut, which is a 20.95% improvement over W-QLED. Meanwhile, due to the Purcell effect of the microcavity, the output efficiency of the QLED coupled with a SiNx waveguide is also significantly improved by optimizing the thickness of the Ag anode and introducing a tilted reflective mirror into the SiNx waveguide. Moreover, the optimal output efficiency of RGB-QLED with the tilted Ag mirror is 10.13%, representing a tenfold increase compared to the sample without the tilted Ag mirror. This design demonstrates an efficient and compact approach for the near-eye full-color display technology. Full article

This study explores the complex relationship between innovation and carbon dioxide (CO₂) emissions across the primary, secondary, and tertiary sectors within the 27 European Union (EU) member states over the period 2017–2023. Drawing on a comprehensive dataset and grounded in theoretical frameworks, the research investigates how different innovation indicators—including broadband penetration, digital skills, public and business R&D expenditure, ICT training, and SME-driven innovations—affect sectoral CO₂ emissions. Using robust regression, the findings reveal a nuanced landscape: while ICT skills training, human resource mobility in science and technology, and SME business process innovations are associated with significant reductions in emissions, certain R&D investments and broadband penetration display positive correlations with emissions in specific service-oriented sectors. These results suggest that the environmental impacts of innovation are highly context-dependent and not uniformly positive. This study highlights the importance of strategically aligning innovation policies with sustainability objectives. Policymakers are encouraged to promote targeted digital training, support environmentally conscious R&D, and foster SME-led innovation practices. The results contribute to the growing discourse on sustainable innovation and provide actionable insights to advance the EU’s green transition. Full article

A polarization-maintaining all-fiber laser source based on a nonlinear amplifying loop mirror with broadband operation (64 nm) around 1920 nm is demonstrated. The oscillator can generate 66 pJ up-chirped dissipative soliton pulses at a repetition rate of 22.8 MHz with a high polarization extinction ratio of 17 dB. By adding a polarization controller to the polarization-maintaining dispersion-compensating fiber, the filter behavior can be adjusted allowing for the tuning of the emission to a center wavelength of 1878 nm, 1907 nm, and 1926 nm. Using an all-polarization-maintaining single-mode fiber amplifier with anomalous dispersion, the pulses are amplified to 0.9 nJ and compressed to a near Fourier-limited pulse duration of 170 fs with a peak power of 4.3 kW. Such all-fiber-based sources are attractive due to their compact size, high beam quality, and good environment stability. Full article

This study explores the development and optical characterization of a hybrid material combining nanoporous anodic alumina with J-aggregates of pseudoisocyanine dyes, highlighting its potential for photonic applications in bright broadband sources. The hybrid material was synthesized by impregnating an alumina matrix with a dye solution, which facilitated a thermally stimulated self-assembly process for the formation of J-aggregates. The incorporation of J-aggregates within the matrix was confirmed through several independent optical measurement techniques. A distinct absorption peak and corresponding luminescence signal were attributed to J-aggregate formation, while energy transfer from the alumina’s intrinsic oxygen vacancy centers to the dye aggregates was observed under specific excitation conditions. Amplified spontaneous emission was achieved under pulsed laser excitation, characterized by spectral narrowing and a nonlinear increase in emission intensity beyond a critical pump threshold, indicative of a similarity with random lasing facilitated by scattering within the porous structure. Full article