Search Results (18)

Polyfarnesene, a bio-based polymer, was epoxidized in situ using performic acid to investigate oxirane ring formation, stability, and the role of its bottlebrush architecture in the kinetics. The reaction reached a maximum epoxidation degree of ~20% after 6 h but underwent side reactions, producing hydroxyl and formic ester groups. FTIR and ¹H NMR revealed that ring opening began within the first hour, whereas residual unsaturated bonds persisted after prolonged reaction, owing to steric shielding by the polymer’s long C11–C13 side chains. Unlike smaller polydiene homologues, polyfarnesene exhibited slower ring-opening kinetics, retaining approximately 10% of oxirane groups after 20 h. GPC showed minimal molecular weight changes but an increase in polydispersity, confirming structural rearrangements without chain scission or crosslinking. DSC demonstrated that oxirane incorporation increased the T_g; however, side reactions reduced this effect by limiting chain mobility. These findings establish that the spatial constraints imposed by the bottlebrush architecture of polyfarnesene govern the reaction kinetics, restricting epoxidation efficiency and favoring esterification pathways. This interplay provides a basis for designing bio-based polymers with tunable thermal properties. Controlling the reaction environment to suppress side reactions is key to producing high-T_g epoxidized derivatives suitable for rubber technologies and sustainable materials. Full article

Ultra-soft injectable hydrogels are paramount in biomedical applications such as tissue fillers, drug depots, and tissue regeneration scaffolds. Synthetic approaches relying on linear polymers are confronted by the necessity for significant dilution of polymer solutions to reduce chain entanglements. Bottlebrush polymers offer an alternative approach due to suppressed chain overlap and entanglements, which facilitates lower solution viscosities and increased gel softness. Leveraging the bottlebrush architecture in linear-bottlebrush-linear (LBL) block copolymer systems, where L is a thermosensitive linear poly(N-isopropylacrylamide) block, and B is a hydrophilic polyethylene glycol brush block, injectable hydrogels were designed to mimic tissues as soft as the extracellular matrix at high polymer concentrations. Compared to an analogous system with shorter brush side chains, increasing the side chain length enables a decrease in modulus by up to two orders of magnitude within 1–100 Pa at 20 wt% polymer concentrations, near to the physiological water content of ~70%. This system further exhibits thermal hysteresis, enabling stability with inherent body temperature fluctuations. The observed features are ascribed to kinetically hindered network formation by bulky macromolecules. Full article

Bottle-brush polymers with aggrecan-like side chains represent a class of biomimetic macromolecules that replicate key structural and functional features of natural complexes of aggrecans with hyaluronic acid (HA) which are the major components of articular cartilage. In this study, we employ numerical self-consistent field (SCF) modeling combined with analytical theory to investigate the conformational properties of cylindrical molecular bottle-brushes composed of aggrecan-like double-comb side chains tethered to the main chain (the backbone of the bottle-brush). We demonstrate that the architecture of the brush-forming double-comb chains and, in particular, the distribution of polymer mass between the root and peripheral domains significantly influences the spatial distribution of primary side chain ends, leading to formation of a “dead” zone near the backbone of the bottle-brush and non-uniform density profiles. The axial stretching force imposed by grafted double-combs in the main chain, as well as normal force acting at the junction point between the bottle-brush backbone and the double-comb side chain are shown to depend strongly on the side-chain architecture. Furthermore, we analyze the induced bending rigidity and persistence length of the bottle-brush, revealing that while the overall scaling behavior follows established power laws, the internal structure can be finely tuned without altering the backbone stiffness. These theoretical findings provide valuable insights into relations between architecture and properties of bottle-brush-like supra-biomolecular structures, such as aggrecan-hyaluronan complexes. Full article

Molecular-mimetic nanocolloids (MMNCs) are promising for advanced materials, yet self-assembly fabrication faces challenges in purity and programmability. We report a total synthesis strategy for surfactant-mimetic nanocolloids (SMNCs), an amphiphilic MMNC subclass. SMNCs consist of a ~5 nm silica nanoparticle head and a bottlebrush polymer tail. Regioselective silica deposition on linear-block-brush polymers via the modified sol–gel method enables precise control. This strategy is versatile and can be adapted to synthesize other MMNCs with different components. It offers a more controlled alternative to self-assembly methods, advancing MMNC synthesis and enabling their broader use in emerging technologies. Full article

In crowded fluids, polymer segments can exhibit anomalous subdiffusion due to the viscoelasticity of the surrounding environment. Previous single-particle tracking experiments revealed that such anomalous diffusion in complex fluids (e.g., in bacterial cytoplasm) can be described by fractional Brownian motion (fBm). To investigate how the viscoelastic media affects the diffusive behaviors of polymer segments without resolving single crowders, we developed a novel fractional Brownian dynamics method to simulate the dynamics of polymers under confinement. In this work, instead of using Gaussian random numbers (“white Gaussian noise”) to model the Brownian force as in the standard Brownian dynamics simulations, we introduce fractional Gaussian noise (fGn) in our homemade fractional Brownian dynamics simulation code to investigate the anomalous diffusion of polymer segments by using a simple “bottle-brush”-type polymer model. The experimental results of the velocity autocorrelation function and the exponent that characterizes the subdiffusion of the confined polymer segments can be reproduced by this simple polymer model in combination with fractional Gaussian noise (fGn), which mimics the viscoelastic media. Full article

Bottlebrush (BB) elastomers with water-soluble side chains and tissue-mimetic mechanical properties are promising for biomedical applications like tissue implants and drug depots. This work investigates the microstructure and phase transitions of BB elastomers with crystallizable polyethylene oxide (PEO) side chains by real-time synchrotron X-ray scattering. In the melt, the elastomers exhibit the characteristic BB peak corresponding to the backbone-to-backbone correlation. This peak is a distinct feature of BB systems and is observable in small- or medium-angle X-ray scattering curves. In the systems studied, the position of the BB peak ranges from 3.6 to 4.8 nm in BB elastomers. This variation is associated with the degree of polymerization of the polyethylene oxide (PEO) side chains, which ranges from 19 to 40. Upon crystallization of the side chains, the intensity of the peak decays linearly with crystallinity and eventually vanishes due to BB packing disordering within intercrystalline amorphous gaps. This behavior of the bottlebrush peak differs from an earlier study of BBs with poly(ε-caprolactone) side chains, explained by stronger backbone confinement in the case of PEO, a high-crystallinity polymer. Microstructural models based on 1D SAXS correlation function analysis suggest crystalline lamellae of PEO side chains separated by amorphous gaps of monolayer-like BB backbones. Full article

We present a novel type of magnetorheological material that allows one to restructure the magnetic particles inside the finished composite, tuning in situ the viscoelasticity and magnetic response of the material in a wide range using temperature and an applied magnetic field. The polymer medium is an A-g-B bottlebrush graft copolymer with side chains of two types: polydimethylsiloxane and polystyrene. At room temperature, the brush-like architecture provides the tissue mimetic softness and strain stiffening of the elastomeric matrix, which is formed through the aggregation of polystyrene side chains into aggregates that play the role of physical cross-links. The aggregates partially dissociate and the matrix softens at elevated temperatures, allowing for the effective rearrangement of magnetic particles by applying a magnetic field in the desired direction. Magnetoactive thermoplastic elastomers (MATEs) based on A-g-B bottlebrush graft copolymers with different amounts of aggregating side chains filled with different amounts of carbonyl iron microparticles were prepared. The in situ restructuring of magnetic particles in MATEs was shown to significantly alter their viscoelasticity and magnetic response. In particular, the induced anisotropy led to an order-of-magnitude enhancement of the magnetorheological properties of the composites. Full article

Post-disturbance rangeland restoration efforts are often thwarted due to soil moisture deficits. Superabsorbent polymers (SAPs) absorb hundreds of times their weight in water, increasing soil moisture when the SAP is mixed with soil. The objective of this study was to evaluate banded SAPs under the soil surface to increase plant available water and thus seedling establishment for perennial rangeland species during restoration efforts. Five glasshouse experiments with two rangeland perennial grass species, bottlebrush squirreltail (Elymus elymoides) or Siberian wheatgrass (Agropyron fragile), were conducted. Treatments varied, including SAP rates ranging from 11–3000 kg ha⁻¹ with placement mostly banded at depths extending from the surface up to a 15 cm depth. Generally, SAPs increased soil moisture at all rates and depths for up to 49 days. However, rates ≥ 750 kg ha⁻¹ caused the soil to swell and crack, potentially hastening soil drying later in the season. Seedling longevity was increased up to 12 days, especially at the high SAP band rate of 3000 kg ha⁻¹ when the band was 8 or 15 cm deep. Further work is needed to verify banded SAP rates and placement depths in the field, ascertain conditions to reduce soil displacement, and evaluate benefits across species. Full article

Densely grafted comb-like macromolecules (bottlebrushes) with alternating solvophobic and solvophilic side chains were studied in a selective solvent and at the liquid interface using mesoscopic computer simulations. The effects of backbone length and copolymer composition were considered. While self-assembly in solution revealed only spherical aggregates for all ar-chitectures studied, adsorption onto the liquid interface in particular cases resulted in morpho-logical changes, with worm-like aggregates or a continuous monolayer observed. In turn, the compression of macromolecules at the interface also leads to morphological transitions, includ-ing the formation of a mesh-like percolated structure. The obtained results may be useful for the preparation of solid nanoparticles of anisotropic shape or nanostructured ultra-thin copolymer films. Full article

Drug nanocrystals, one of most common drug delivery systems, enable the delivery of poorly water-soluble drugs with high drug loading and enhanced dissolution. The rapid clearance and uncontrolled drug release of drug nanocrystals limit their delivery efficiency and clinical application. Herein, an amphiphilic co-polymer, poly oligo(ethylene glycol) methacrylate-b-poly(styrene–co-4-formylphenyl methacrylate) (POEGMA-b-P (St-co-FPMA), PPP), characterized by a hydrophilic part with bottlebrush-like oligo(ethylene glycol) methacrylate (OEGMA) side chains, was synthesized as stabilizers to fabricate a high-drug-loading nanocrystal micelle (053-PPP NC micelle) using the chronic myeloid leukemia (CML) drug candidate N-(2-methyl-5-(3-(trifluoromethyl)benzamido)phenyl)-4-(methylamino)pyrimidine-5-carboxamide (CHMFL-ABL-053 or 053) as a model drug. The 053-PPP NC micelle was characterized and subjected to in vitro and in vivo studies. It featured a worm-like shape of small size, high drug loading (~50%), high colloidal stability, and controlled release in vitro. The presence of the 053-PPP NC micelle resulted in a long-circulation property and a much higher AUC. The 053-PPP NC micelle induced higher accumulation in the tumor tissues under multiple continuous administration. For in vivo efficacy, the 053-PPP NC micelle with a longer dosing interval (96 h), beneficial for improving patient adherence, demonstrated superiority to the 053-F127 NC. The proposed stabilizer PPP and the 053-PPP NC micelle with high drug loading enables drug delivery with long circulation and controlled release of drugs. It is also promising for the development of more efficient nanocrystal-based intravenous injection formulations for poorly water-soluble drugs. It might also offer new possibilities for potential clinical application of the CML candidate drug 053. Full article

An extremely efficient lubrication system is achieved in synovial joints by means of bio-lubricants and sophisticated nanostructured surfaces that work together. Molecular bottlebrush structures play crucial roles for this superior tribosystem. For example, lubricin is an important bio-lubricant, and aggrecan associated with hyaluronan is important for the mechanical response of cartilage. Inspired by nature, synthetic bottlebrush polymers have been developed and excellent aqueous boundary lubrication has been achieved. In this review, we summarize recent experimental investigations of the interfacial lubrication properties of surfaces coated with bottlebrush bio-lubricants and bioinspired bottlebrush polymers. We also discuss recent advances in understanding intermolecular synergy in aqueous lubrication including natural and synthetic polymers. Finally, opportunities and challenges in developing efficient aqueous boundary lubrication systems are outlined. Full article

Amphiphilic random and diblock thermoresponsive oligo(ethylene glycol)-based (co)polymers were synthesized via photoiniferter polymerization under visible light using trithiocarbonate as a chain transfer agent. The effect of solvent, light intensity and wavelength on the rate of the process was investigated. It was shown that blue and green LED light could initiate RAFT polymerization of macromonomers without an exogenous initiator at room temperature, giving bottlebrush polymers with low dispersity at sufficiently high conversions achieved in 1–2 h. The pseudo-living mechanism of polymerization and high chain-end fidelity were confirmed by successful chain extension. Thermoresponsive properties of the copolymers in aqueous solutions were studied via turbidimetry and laser light scattering. Random copolymers of methoxy- and alkoxy oligo(ethylene glycol) methacrylates of a specified length formed unimolecular micelles in water with a hydrophobic core consisting of a polymer backbone and alkyl groups and a hydrophilic oligo(ethylene glycol) shell. In contrast, the diblock copolymer formed huge multimolecular micelles. Full article

In this work, the interactions between bottlebrush polymers and phospholipid membranes were investigated using dissipative particle dynamics simulations. The weak and strong adsorption phenomena between the polymers and membranes were examined by calculating the system parameters. A spring model was introduced to explain the variances in the shape factors and the radius of gyration of the bottlebrush polymers, as well as the order parameters of the phospholipid membrane in the pulling processes. This work provides further understanding for the application of bottlebrush polymers in biological processes. Full article

The cellular surface contains specific proteins, also known as lectins, that are carbohydrates receptors involved in different biological events, such as cell–cell adhesion, cell recognition and cell differentiation. The synthesis of well-defined polymers containing carbohydrate units, known as glycopolymers, by reversible deactivation radical polymerization (RDRP) methods allows the development of tailor-made materials with high affinity for lectins because of their multivalent interaction. These polymers are promising candidates for the biomedical field, namely as novel diagnostic disease markers, biosensors, or carriers for tumor-targeted therapy. Although linear glycopolymers are extensively studied for lectin recognition, branched glycopolymeric structures, such as polymer brushes can establish stronger interactions with lectins. This specific glycopolymer topology can be synthesized in a bottlebrush form or grafted to/from surfaces by using RDRP methods, allowing a precise control over molecular weight, grafting density, and brush thickness. Here, the preparation and application of glycopolymer brushes is critically discussed and future research directions on this topic are suggested. Full article

Linear and nonlinear rheological properties of model comb polystyrenes (PS) with loosely to densely grafted architectures were measured under small and medium amplitude oscillatory shear (SAOS and MAOS) flow. This comb PS set had the same length of backbone and branches but varied in the number of branches from 3 to 120 branches. Linear viscoelastic properties of the comb PS were compared with the hierarchical model predictions. The model underpredicted zero-shear viscosity and backbone plateau modulus of densely branched comb with 60 or 120 branches because the model does not include the effect of side chain crowding. First- and third-harmonic nonlinearities reflected the hierarchy in the relaxation motion of comb structures. Notably, the low-frequency plateau values of first-harmonic MAOS moduli scaled with $M_{\mathrm{w}}^{-2}$ (total molecular weight), reflecting dynamic tube dilution (DTD) by relaxed branches. Relative intrinsic nonlinearity Q₀ exhibited the difference between comb and bottlebrush via no low-frequency Q₀ peak of bottlebrush corresponding to backbone relaxation, which is probably related to the stretched backbone conformation in bottlebrush. Full article