Search Results (64)

In this paper, a series of polyaniline (PANI)/Ti₃C₂ MXene composites (PMCs) with a biomimetic structure were prepared and employed as an anticorrosion coating application. First, the PANI was synthesized by oxidative polymerization with ammonium persulfate as the oxidant. Then, 2D Ti₃C₂ MXene nanosheets were prepared by treating the Ti₃AlC₂ using the optimized minimally intensive layer delamination (MILD) method, followed by characterization via XRD and SEM. Subsequently, the PMC was prepared by the oxidative polymerization of aniline monomers in the presence of Ti₃C₂ MXene nanosheets, followed by characterization via FTIR, XRD, SEM, TEM, CV, and UV–Visible. Eventually, the PMC coatings with the artificial biomimetic surface structure of a macaw feather were prepared by the nano-casting technique. The corrosion resistance of the PMC coatings, evaluated via Tafel polarization and Nyquist impedance measurements, shows that increasing the MXene loading up to 5 wt % shifts the corrosion potential (E_corr) on steel from −588 mV to −356 mV vs. SCE, reduces the corrosion current density (I_corr) from 1.09 µA/cm² to 0.035 µA/cm², and raises the impedance modulus at 0.01 Hz from 67 kΩ to 3794 kΩ. When structured with the hierarchical feather topography, the PMC coating (Bio-PA-MX-5) further advances the E_corr to +103.6 mV, lowers the I_corr to 7.22 × 10⁻⁴ µA/cm², and boosts the impedance to 96,875 kΩ. Compared to neat coatings without biomimetic structuring, those with engineered biomimetic surfaces showed significantly improved corrosion protection performance. These enhancements arise from three synergistic mechanisms: (i) polyaniline’s redox catalysis accelerates the formation of a dense passive oxide layer; (ii) MXene nanosheets create a tortuous gas barrier that cuts the oxygen permeability from 11.3 Barrer to 0.9 Barrer; and (iii) the biomimetic surface traps air pockets, raising the water contact angle from 87° to 135°. This integrated approach delivers one of the highest combined corrosion potentials and impedance values reported for thin-film coatings, pointing to a general strategy for durable steel protection. Full article

To address the challenges of cotton cellulose materials being susceptible to environmental humidity and pollutant erosion, a strategy for constructing superhydrophobic functional coatings with biomimetic micro–nano composite structures was proposed. Through surface silanization modification, diatomite (DEM) and Fe₃O₄ nanoparticles were functionalized with octyltriethoxysilane (OTS) to prepare superhydrophobic diatomite flakes (ODEM) and OFe₃O₄ nanoparticles. Following the multi-scale composite principle, ODEM and OFe₃O₄ nanoparticles were blended and crosslinked via the hydroxyl-initiated ring-opening polymerization of epoxy resin (EP), resulting in an EP/ODEM@OFe₃O₄ composite coating with hierarchical roughness. Microstructural characterization revealed that the micrometer-scale porous structure of ODEM and the nanoscale protrusions of OFe₃O₄ form a hierarchical micro–nano topography. The special topography combined with the low surface energy property leads to a contact angle of 158°. Additionally, the narrow bandgap semiconductor characteristic of OFe₃O₄ induces the localized surface plasmon resonance effect. This enables the coating to attain 80% light absorption across the 350–2500 nm spectrum, and rapidly heat to 45.8 °C within 60 s under 0.5 sun, thereby demonstrating excellent deicing performance. This work provides a theoretical foundation for developing environmentally tolerant superhydrophobic photothermal coatings, which exhibit significant application potential in the field of anti-icing and anti-fouling. Full article

Both biochemical cues and the electrophysiological microenvironment play a pivotal role in influencing cell behaviors. In this study, collagen/polypyrrole biomimetic electroactive composite coatings with a fiber network structure were constructed on the surface of titanium substrates by hot alkali treatment and stepwise electrochemical deposition. Materialistic characterization and electrochemical performance tests demonstrated that the titanium electrodes modified with collagen/polypyrrole composite coatings exhibited the surface morphology of a collagen film layer, and their electroactivity was significantly enhanced. Cellular experiments demonstrated that the collagen in the composite coatings could provide good biomimetic biochemical cues as a main extracellular matrix component, which have a substantial effect in promoting cell adhesion, proliferation, and osteogenic differentiation. Furthermore, under exogenous electrical signals, the polypyrrole coating has the capacity to facilitate an appropriate electrophysiological microenvironment, thereby promoting osteogenic differentiation. The collagen/polypyrrole composite coating exhibited a better effect in promoting osteogenic differentiation among all samples by simultaneously providing the appropriate biochemical cues and electrophysiological microenvironments. This work demonstrates the feasibility of synergistic pro-osteogenesis by biochemical cues and an electrophysiological microenvironment, which is instructive for the field of bone tissue engineering. Full article

This study presents a novel approach to fabricating magnetic sponge-like composites by melting various types of steel onto three-dimensional (3D) carbonized spongin scaffolds under extreme biomimetic conditions. Spongin, a renewable marine biopolymer with high thermal stability, was carbonized at 1200 °C to form a turbostratic graphite matrix capable of withstanding the high-temperature steel melting process (1450–1600 °C). The interaction between molten steel vapors and the carbonized scaffolds resulted in the formation of nanostructured iron oxide (primarily hematite) coatings, which impart magnetic properties to the resulting composites. Detailed characterization using SEM-EDX, HRTEM, FT-IR, and XRD confirmed the homogeneous distribution of iron oxides on and within the carbonized fibrous matrix. Electrochemical measurements further demonstrated the electrocatalytic potential of the composite, particularly the sample modified with stainless steel 316L—for the hydrogen evolution reaction (HER), offering promising perspectives for green hydrogen production. This work highlights the potential of extreme biomimetics to create functional, scalable, and sustainable materials for applications in catalysis, environmental remediation, and energy technologies. Full article

In recent years, flexible piezoresistive sensors based on polydimethylsiloxane (PDMS) matrix materials have developed rapidly, showing broad application prospects in fields such as human motion monitoring, electronic skin, and intelligent robotics. However, achieving a balance between structural durability and fabrication simplicity remains challenging. Traditional methods for preparing PDMS flexible substrates with high porosity and high stability often require complex, costly processes. Breaking through the constraints of conventional material systems, this study innovatively combines the high elasticity of polydimethylsiloxane (PDMS) with the stochastically distributed porous topology of a sponge-derived biotemplate through biomimetic templating replication technology, fabricating a heterogeneous composite system with an architecturally asymmetric spatial network. After 5000 loading cycles, uncoated samples experienced a thickness reduction of 7.0 mm, while PDMS-coated samples showed minimal thickness changes (2.0–3.0 mm), positively correlated with curing agent content (5:1 to 20:1). The 5:1 ratio sample demonstrated exceptional mechanical stability. As evidenced, the PDMS film-encapsulated architecturally asymmetric spatial network demonstrates superior stress dissipation efficacy, effectively mitigating stress concentration phenomena inherent to symmetric configurations that induce matrix fracture, thereby achieving optimal mechanical stability. Compared to the pre-test resistance distribution of 10–248 Ω, after 5000 cyclic loading cycles, the uncoated samples exhibited a narrowed resistance range of 10–50 Ω, while PDMS-coated samples maintained a broader resistance range (10–240 Ω) as the curing agent ratio increased (from 20:1 to 5:1), demonstrating that increasing the curing agent ratio helps maintain conductive network stability. The 5:1 ratio sample displayed the lowest resistance variation rate attenuation—only 3% after 5000 cycles (vs. 80% for uncoated samples)—and consistently minimal attenuation at all stages, validating superior electrical stability. Under 0–6 kPa pressure, the 5:1 ratio device maintained a linear sensitivity of 0.157 kPa⁻¹, outperforming some existing works. Human motion monitoring experiments further confirmed its reliable signal output. Furthermore, the architecturally asymmetric spatial network of the device enables superior conformability to complex curvilinear geometries, leveraging its structural anisotropy to achieve seamless interfacial adaptation. By synergistically optimizing material composition and structural design, this study provides a novel technical method for developing highly durable flexible electronic devices. Full article

Throughout millions of years of biological evolution, shell structures have developed a highly complex layered organic–inorganic structure that makes them effective against a wide range of external impacts, including mechanical stress and chemical corrosion. Therefore, shell-like biomimetic materials are considered to possess high strength and toughness. Nevertheless, although shell structures have exhibited superior performance across multiple domains, understanding of their structural complexities and corrosion protection mechanisms remains relatively limited within the scope of human knowledge. In this study, alternating ZnO–graphene/epoxy coatings featuring shell-like structures were synthesized, and their anticorrosion properties were evaluated through the incorporation of ZnO to enhance the dispersion of graphene. Electrochemical impedance spectroscopy (EIS) tests showed that with an increased number of ZnO–graphene layers, the coating resistance of the bionic composite coating also increased: from 8.21 × 10⁷ Ω·cm² of the pure epoxy coating to 7.64 × 10⁸ Ω cm². The composite coating, comprising three alternating layers of zinc oxide and four layers of epoxy resin, exhibited an electrochemical impedance two orders of magnitude greater than that of pure epoxy resin following immersion in a 3.5% sodium chloride solution, demonstrating excellent corrosion resistance. The results showed that with increased ZnO–graphene layers, ZnO–graphene disperses more uniformly in water and has greater rigidity. Full article

The purpose of coatings is to protect or enhance the functionality of the substrate material, irrespective of the field in which the material was designed. The use of coatings in medicine is rapidly expanding with the objective of enhancing the osseointegration ability of metallic materials such as titanium. The aim of this study was to obtain biomimetic hydroxyapatite (HAp)-based coatings on titanium by using the pulsed galvanostatic method. The morphology of the HAp-based coatings revealed the presence of very thin and wide plate-like crystals, grown perpendicular to the Ti substrate, while the chemical composition highlighted a Ca/P ratio of 1.66, which is close to that of stoichiometric HAp (1.67). The main phases and chemical bonds identified confirmed the presence of the HAp phase in the developed coatings. A roughness of 228 nm and a contact angle of approx. 17° were obtained for the HAp coatings, highlighting a hydrophilic character. In terms of biomineralization and electrochemical behavior, it was shown that the HAp coatings have significantly enhanced the titanium properties. Finally, the in vitro cell tests carried out with human mesenchymal stem cells showed that the Ti samples coated with HAp have increased cell viability, extracellular matrix, and Ca intracellular deposition when compared with the uncoated Ti, indicating the beneficial effect. Full article

The extended immersion of ships in seawater frequently results in biofouling, a condition characterized by the accumulation of marine organisms such as barnacles and algae. To combat this issue, the application of anti-fouling coatings to the hull surfaces of vessels has emerged as one of the most effective strategies. In response to the increasing global emphasis on environmental sustainability, there is a growing demand for anti-fouling coatings that not only demonstrate superior anti-fouling efficacy but also adhere to stringent environmental standards. The traditional use of organotin-based self-polishing anti-fouling coatings, known for their high toxicity, has been prohibited due to environmental concerns. Consequently, there is a progressive shift toward the development and application of environmentally friendly anti-fouling coatings. This paper reviews the toxicity and application limitations associated with conventional anti-fouling coatings. It provides a comprehensive overview of recent advancements in the field, including the development of novel self-polishing anti-fouling coatings, low surface energy coatings, biomimetic coatings, and nanostructured coatings, each leveraging distinct anti-fouling mechanisms. The paper evaluates the composition and performance of these emerging coatings and identifies key technical challenges that remain unresolved. It also proposes a multi-faceted approach to addressing these challenges, suggesting potential solutions for enhancing the effectiveness and environmental compatibility of anti-fouling technologies. The paper forecasts future research directions and development trajectories for marine anti-fouling coatings, emphasizing the need for continued innovation to achieve both environmental sustainability and superior anti-fouling performance. Full article

Surface roughness and low surface energy are key elements for the artificial preparation of biomimetic superhydrophobic materials. However, the presence of micro-/nanostructures and the corresponding increase in roughness can increase light scattering, thereby reducing the surface transparency. Therefore, designing and constructing superhydrophobic surfaces that combine superhydrophobicity with high transparency has been a continuous research focus for researchers and engineers. In this study, a transparent superhydrophobic coating was constructed on glass substrates using hydrophobic fumed silica (HF-SiO₂) and waterborne polyurethane (WPU) as raw materials, combined with a simple spray-coating technique, resulting in a water contact angle (WCA) of 158.7 ± 1.5° and a sliding angle (SA) of 6.2 ± 1.8°. Characterization tests including SEM, EDS, LSCM, FTIR, and XPS revealed the presence of micron-scale protrusions and a nano-scale porous network composite structure on the surface. The presence of HF-SiO₂ not only provided a certain roughness but also effectively reduced surface energy. More importantly, the coating exhibited excellent water-repellent properties, extremely low interfacial adhesion, self-cleaning ability, and high transparency, with the light transmittance of the coated glass substrate reaching 96.1% of that of the bare glass substrate. The series of functional characteristics demonstrated by the transparent superhydrophobic HF-SiO₂@WPU coating designed and constructed in this study will play an important role in various applications such as underwater observation windows, building glass facades, automotive glass, and goggles. Full article

In this study, a series of amine-modified mesoporous silica (AMS)-based epoxy composites with superhydrophobic biomimetic structure surface of Xanthosoma sagittifolium leaves (XSLs) were prepared and applied as anti-corrosion and anti-biofilm coatings. Initially, the AMS was synthesized by the base-catalyzed sol–gel reaction of tetraethoxysilane (TEOS) and triethoxysilane (APTES) through a non-surfactant templating route. Subsequently, a series of AMS-based epoxy composites were prepared by performing the ring-opening polymerization of DGEBA with T-403 in the presence of AMS spheres, followed by characterization through FTIR, TEM, and CA. Furthermore, a nano-casting technique with polydimethylsiloxane (PDMS) as the soft template was utilized to transfer the surface pattern of natural XSLs to AMS-based epoxy composites, leading to the formation of AMS-based epoxy composites with biomimetic structure. From a hydrophilic CA of 69°, the surface of non-biomimetic epoxy significantly increased to 152° upon introducing XSL surface structure to the AMS-based epoxy composites. Based on the standard electrochemical anti-corrosion and anti-biofilm measurements, the superhydrophobic BEAMS3 composite was found to exhibit a remarkable anti-corrosion efficiency of ~99% and antimicrobial efficacy of 82% as compared to that of hydrophilic epoxy coatings. Full article

The design of new, biomimetic biomaterials is of great strategic interest and is converging for many applications, including in implantology. This study explores a novel approach to improving dental implants. Although endosseous TA6V alloy dental implants are widely used in oral implantology, this material presents significant challenges, notably the prevalence of peri-implantitis. Therefore, in this study, we investigate a new advance in the design of hybrid medical devices. This involves the design of a Ca-SZ coating deposited by PVD on a TA6V substrate. This approach aims to overcome the inherent limitations of each of these materials, namely TA6V’s susceptibility to peri-implantitis on the one hand and zirconia’s excessively high Young’s modulus compared with bone on the other, while benefiting from their respective advantages, such as the ductility of TA6V and the excellent biocompatibility of zirconia, offering relevant prospects for the design of high-performance implantable medical devices. This study integrates characterisation techniques, focusing on the structural and elemental analysis of the Ca-SZ coating by XRD and TEM. The results suggest that this coating combines a tetragonal structure, a uniform morphology with no apparent defects, a clean interface highlighting good adhesion, and a homogeneous composition of calcium, predisposing it to optimal biocompatibility. All of these findings make this innovative coating a particularly suitable candidate for application in dental implantology. Full article

Introduction. Modern medicine depends on biomaterials. Thus, it is imperative that these materials continue to be developed and improved. Methods. This work aimed at designing hydroxyapatite-based coatings (HAp) with high osseointegration properties by developing a biomimetic morphology that resembles that of natural HAp found in bone tissue. The biomimetic HAp coatings with plate-like morphology were successfully obtained using the pulsed galvanostatic electrochemical approach on pure Ti discs. The coatings were investigated in terms of surface morphology, chemical and phasic composition, in vitro bioactivity, and cell interaction. Results and Discussion. The morphological investigations revealed that using electrochemical deposition, HAp-based coatings with very thin and wide plate-like crystals can be obtained. The chemical composition highlighted that both Ca and P are present, and that the Ca/P ratio registered values of 1.66, being close to that of the stoichiometric HAp of 1.67. The phasic composition analysis showed that the main phase consisted of hydroxyapatite (ICDD #09-0432), with a crystallinity of ~25%. The biomineralization ability of the cp-Ti substrate was improved by the HAp-based coatings, reaching a maximum value of 9.7 mg after 3 weeks of immersion in simulated body fluid (SBF) compared to the Ti samples which gained a mass of only 0.3 mg after the same period. The in vitro experiments using human mesenchymal stem cells demonstrated that the HAp-based coatings enhanced the extracellular matrix, the intracellular deposition of Ca, and cell viability when compared to the cp-Ti substrate, demonstrating the advantages of the developed coatings. Conclusions. Therefore, the outcomes confirm that coatings with improved and adjustable properties can be designed for medical applications by using the electrochemical deposition technique. Full article

This study examined the effectiveness of coating demineralized bone matrix (DBM) with amorphous calcium phosphate (DBM + CaP), as well as a composite of DBM, calcium phosphate, and serum albumin (DBM + CaP + BSA). The intact structure of DBM promotes the transformation of amorphous calcium phosphate (CaP) into dicalcium phosphate dihydrate (DCPD) with a characteristic plate shape and particle size of 5–35 µm. The inclusion of BSA in the coating resulted in a better and more uniform distribution of CaP on the surface of DBM trabeculae. MG63 cells showed that both the obtained forms of CaP and its complex with BSA did not exhibit cytotoxicity up to a concentration of 10 mg/mL in vitro. Ectopic (subcutaneous) implantation in rats revealed pronounced biocompatibility, as well as strong osteoconductive, osteoinductive, and osteogenic effects for both DBM + CaP and DBM + CaP + BSA, but more pronounced effects for DBM + CaP + BSA. In addition, for the DBM + CaP + BSA samples, there was a pronounced full physiological intrafibrillar biomineralization and proangiogenic effect with the formation of bone-morrow-like niches, accompanied by pronounced processes of intramedullary hematopoiesis, indicating a powerful osteogenic effect of this composite. Full article

This study presents a comprehensive evaluation of novel composite biomaterials designed for dental applications, aiming to potentially address the prevalent challenge of dental and periodontal tissue loss. The composites consisted of biomimetic hydroxyapatite (mHA) enriched with Mg²⁺, CO₃²⁻, and Zn²⁺ ions, type I collagen, alginate, and, additionally, chitosan and sericin. The granules were loaded with ibuprofen sodium salt. The investigation encompassed a morphology characterization, a porosity analysis, a chemical structure assessment, and an examination of the swelling behavior, drug release kinetics (ibuprofen), and release profiles of zinc and magnesium ions. The granules exhibited irregular surfaces with an enhanced homogeneity in the chitosan-coated granules and well-developed mesoporous structures. The FT-IR spectra confirmed the presence of ibuprofen sodium, despite overlapping bands for the polymers. The granules demonstrated a high water-absorption capacity, with delayed swelling observed in the chitosan-coated granules. Ibuprofen displayed burst-release profiles, especially in the G1 and G3 samples. In the case of the chitosan-coated granules (G2 and G4), lower amounts of ibuprofen were released. In turn, there was a significant difference in the released amount of magnesium and zinc ions from the granules, which was most likely caused by their different location in the hydroxyapatite crystals. The cytotoxicity assays confirmed the non-cytotoxic behavior of the biomaterial. These findings suggest the potential applicability of these biomaterials in dental scenarios, emphasizing their multifunctional and biocompatible nature. Full article

The lattice metamaterial has attracted extensive attention due to its excellent specific strength, energy absorption capacity, and strong designability of the cell structure. This paper aims to explore the functional nickel plating on the basis of biomimetic-designed lattice structures, in order to achieve higher stiffness, strength, and energy absorption characteristics. Two typical structures, the body-centered cubic (BCC) lattice and the bioinspired hierarchical circular lattice (HCirC), were considered. The BCC and HCirC lattice templates were prepared based on DLP (digital light processing) 3D printing. Based on this, chemical plating, as well as the composite plating of chemical plating followed by electroplating, was carried out to prepare the corresponding nickel-plated lattice structures. The mechanical properties and deformation failure mechanisms of the resin-based lattice, chemically plated lattice, and composite electroplated lattice structures were studied by using compression experiments. The results show that the metal coating can significantly improve the mechanical properties and energy absorption capacity of microlattices. For example, for the HCirC structure with the loading direction along the x-axis, the specific strength, specific stiffness, and specific energy absorption after composite electroplating increased by 546.9%, 120.7%, and 2113.8%, respectively. The shell–core structure formed through composite electroplating is the main factor for improving the mechanical properties of the lattice metamaterial. In addition, the functional nickel plating based on biomimetic structure design can further enhance the improvement space of mechanical performance. The research in this paper provides insights for exploring lighter and stronger lattice metamaterials and their multifunctional applications. Full article