Search Results (112)

The development of gas sensors with high sensitivity and low operating temperatures is essential for practical applications in environmental monitoring and industrial safety. SnO₂-based gas sensors, despite their widespread use, often suffer from high working temperatures and limited sensitivity to H₂ gas, which presents significant challenges for their performance and application. This study addresses these issues by introducing a novel SnO₂-based sensor featuring a three-dimensional (3D) nanostructure, designed to enhance sensitivity and allow for room-temperature operation. This work lies in the use of a 3D anodic aluminum oxide (AAO) template to deposit SnO₂ nanoparticles through ultrasonic spray pyrolysis, followed by modification with platinum (Pt) nanoparticles to further enhance the sensor’s response. The as-prepared sensors were extensively characterized, and their H₂ sensing performance was evaluated. The results show that the 3D nanostructure provides a uniform and dense distribution of SnO₂ nanoparticles, which significantly improves the sensor’s sensitivity and repeatability, especially in H₂ detection at room temperature. This work demonstrates the potential of utilizing 3D nanostructures to overcome the traditional limitations of SnO₂-based sensors. Full article

Synthetic nanopores were recently demonstrated with memristive and nonlinear voltage-current behaviors, akin to ion channels in a cell membrane. Such ionic devices are considered a promising candidate for the development of brain-inspired neuromorphic computing techniques. In this work, we show the composite behavior of nanopore-array large memristors, formed with different membrane materials, pore sizes, electrolytes, and device arrangements. Anodic aluminum oxide (AAO) membranes with 5 nm and 20 nm diameter pores and track-etched polycarbonate (PCTE) membranes with 10 nm diameter pores are tested and shown to demonstrate memristive and nonlinear behaviors with approximately 10⁷–10¹⁰ pores in parallel when electrolyte concentration across the membranes is asymmetric. Ion diffusion through the large number of channels induces time-dependent electrolyte asymmetry that drives the system through different memristive states. The behaviors of series composite memristors with different configurations are also presented. In addition to helping understand fluidic devices and circuits for neuromorphic computing, the results also shed light on the development of field-assisted ion-selection-membrane filtration techniques as well as the investigations of large neurons and giant synapses. Further work is needed to de-embed parasitic components of the measurement setup to obtain intrinsic large memristor properties. Full article

We developed a novel and portable magnetic nanochannel electrochemical sensor for the sensitive detection of cadmium ions (Cd²⁺), which pose serious risks to food safety and human health. The sensor was fabricated by co-modifying an anodic aluminum oxide (AAO) nanochannel membrane with a composite of glutathione (GSH) and ferric oxide nanoparticles (Fe₃O₄), denoted as GSH@Fe₃O₄. This modified membrane was then integrated with a screen-printed carbon electrode (SPCE) to construct the GSH@Fe₃O₄/GSH@AAO/SPCE sensing platform. The performance of the sensor was evaluated using differential pulse voltammetry (DPV), which demonstrated a strong linear correlation between the peak current response and the concentration of Cd²⁺ in the range of 5–120 μg/L. The calibration equation was I_DPV(μA) = −0.31 + 0.98·C_{Cd²⁺(μg/L)}, with an excellent correlation coefficient (R² = 0.999, n = 3). The calculated limit of detection (LOD) was as low as 0.1 μg/L, indicating the high sensitivity of the system. These results confirm the successful construction of the GSH@Fe₃O₄/GSH@AAO/SPCE portable nanochannel sensor. This innovative sensing platform provides a rapid, sensitive, and user-friendly approach for the on-site monitoring of heavy metal contamination in agricultural products, especially grains. Full article

We explored anodic aluminum oxide (AAO) stealth materials combining low infrared emissivity and visible structural coloration through multi-parameter modulation. Using DC ion gold sputtering and UHV magnetron chromium sputtering, we successfully prepared an AAO stealth material with high-saturation visible structural coloration and low infrared emissivity (ε < 0.17). Quantitative evaluation based on the CIE Lab color difference model indicated that the gold-coated samples had high matching accuracy with PANTONE standard colors ($\mathsf{\Delta }{E}_{ab}^{*}$ < 1.6). The chromium-coated samples had slightly lower matching accuracy ($\mathsf{\Delta }{E}_{ab}^{*}$ < 3.0), but still displayed rich coloration, with color difference within human-perceptible tolerance limits. Full article

With the evolution of micro/nanotechnology, anodic aluminum oxide (AAO) has received attention for sensor applications due to its regular and high-aspect-ratio nanopore structure with an excellent sensing performance, especially for electrical and optical sensors. Here, we propose the application of these capacitance and porous properties in a facile nanoporous AAO liquid sensor and study an efficient and economical method for preparing AAO substrates for liquid-phase substance sensing. By applying hybrid pulse anodization (HPA), a growth rate of approximately 5.9 μm/h was achieved in AAO fabrication. Compared to traditional low-temperature (0–10 °C) and two-step anodization with a growth rate of 1–3 μm/h, this process is significantly improved. The effect of pore widening on the performance of electrical sensors is also investigated and discussed. After pore widening, the capacitance values of AAO for air as a reference and various liquids, namely deionized water, alcohol, and acetone, are measured as 3.8 nF, 295.3 nF, 243.5 nF, and 210.1 nF, respectively. These results align with the trend in the dielectric constants and demonstrate the ability to clearly distinguish between different substances. The mechanism of AAO capacitive liquid-phase sensors can mainly be explained from two perspectives. First, since an AAO capacitive sensor is a parallel capacitor structure, the dielectric constant of the substance directly influences the capacitance value. In addition, pore widening increases the proportion of liquid filling the structure, enabling the sensor to clearly differentiate between substances. The other is the affinity between the substance and the AAO sensor, which can be determined using a contact angle test. The contact angles are measured as values of 93.2° and 67.7° before and after pore widening, respectively. The better the substance can fully fill the pores, the higher the capacitance value it yields. Full article

The current research developed an optical carbon dioxide (CO₂) sensor using anodized aluminum oxide (AAO) as the substrate. We developed an optical carbon dioxide (CO₂) sensor utilizing CdSe/ZnS quantum dots (QDs) as the fluorescent dye and Phenol Red as the pH indicator. The QDs acted as the CO₂-responsive fluorophore and were embedded in a polyimide butyl methacrylate (polyIBM) matrix. This sensing solution was applied to an anodized aluminum oxide (AAO) substrate, which provided a porous and stable platform for sensor fabrication. Photoluminescence measurements were conducted using the coated AAO substrate, with excitation from a 405 nm LED light source. The sensor exhibited red fluorescence emission at 570 nm and could detect CO₂ concentrations in the linear range of 0–100%. Experimental results showed that fluorescence intensity increased with CO₂ concentration, achieving a sensitivity of 211. A wavelength shift of 0.1657 nm/% was observed, indicating strong interactions among CO₂ molecules, Phenol Red, and the QDs within the AAO matrix. The sensor demonstrated a response time of 55 s and a recovery time of 120 s. These results confirm the effectiveness of this optical sensing approach in minimizing fluctuations from the excitation light source and highlight the potential of the AAO-supported QDs and Phenol Red composite as a reliable CO₂ sensing material. This advancement holds promise for applications in both medical and industrial fields. Full article

The aim of this paper is to develop a compact, rapid-response pressure sensor for underwater propulsion. Flexible pressure sensors are widely utilized in human–computer interactions and wearable electronic devices; however, manufacturing capacitive sensors that offer a broad pressure range and high sensitivity presents significant challenges. Inspired by the dermal papillary microstructure, a capacitive pressure sensor was prepared by infusing polydimethylsiloxane (PDMS) inside an anodic aluminum oxide (AAO) template and then demolding it. The resulting pressure sensor exhibits several key characteristics: high linearity in the range of −5.2 to 6.3 kPa, a comprehensive range for both positive and negative pressure sensing in air or water environments, a quick response time of 52 ms, a recovery time of 40 ms, and excellent stability. The sensor presented in this work is innovatively applied to detect underwater negative pressure, and it is employed for the swift detection of positive and negative pressure changes in underwater thrusters. This work highlights the promising potential of biomimetic flexible capacitive pressure sensors across various applications. Full article

The contamination of water bodies with toxic compounds from the agricultural, industrial, and domestic sectors is a serious environmental problem. Adsorption is one of the simplest, most functional, and economical methods for treating large volumes of water and removing its contaminant load. Thanks to its nanoporous structure, versatility, chemical inertness, and low-cost synthesis, anodic aluminum oxide (AAO) can be used as an adsorbent in a wide range of applications. In this work, nanostructured AAO coatings were successfully synthesized, and their performance as adsorbents was evaluated in decolorization tests of Eriochrome Black T (EBT) solutions. The adsorption process was found to be dependent on the initial dye concentration, agitation, temperature, and contact time. At 25 °C and 16 mg·L⁻¹ initial EBT concentration, a maximum removal efficiency (%R) of 78% was obtained after 4.5 h at 500 rpm and after 5.5 h at 100 rpm, while without agitation, after 8.3 h of treatment, the highest %R was 40%. Furthermore, the adsorption rate increased significantly with temperature, reaching a %R of 99% after 2.25 h at 60 °C and 500 rpm. Additionally, it was demonstrated that the adsorbent can be used up to four times with a removal efficiency greater than 50%. Full article

Anodic aluminum oxide (AAO) is a promising material for sensor applications due to its unique nanoporous structure and high surface area. This study investigates enhancing AAO’s sensing capabilities by incorporating carbyne-enriched nanomaterials. This research aimed to create a novel surface acoustic wave (SAW) sensor with improved performance characteristics. AAO films were fabricated using a two-step anodization process, followed by carbyne-enriched coating deposition via ion-assisted pulse-plasma deposition. The dielectric properties of the resulting composite material were characterized using impedance spectroscopy, while the sensing performance was evaluated by exposing the sensor to various ethanol concentrations. The results showed a significant increase in capacitance and dielectric permittivity for the carbyne-filled AAO compared to pristine AAO, along with a 5-fold improvement in sensitivity to ethanol vapor. The increased sensitivity is attributed to the synergistic combination of the AAO’s high surface area and the carbyne’s unique electrical properties. This work demonstrates the successful fabrication and characterization of a novel high-sensitivity gas sensor, highlighting the potential of carbyne-enriched AAO for advanced sensor applications. Full article

Anodizing can generate porous wear-resistant layers, which can act as reservoirs for gradually releasing lubricants. Studies on the formation of zinc dialkyl dithiophosphate (ZDDP) tribofilms in non-ferrous metals are relatively rare. Furthermore, adding nanoparticles can improve wear resistance in various applications. This investigation aims to correlate several anodized surfaces using H₂SO₄ (5 or 10%wt. concentration and 45 or 60 min exposition) to tribological outputs, contributing to understanding the friction behavior of non-metallic layers. Three steps were applied on anodized Alumold 500 alloy. Firstly, the scratching test, to select the layers with higher critical loads. The greatest scratch resistance was obtained with the highest H³/E² value and thickest layer. Secondly, lubricated tests with only poly-alpha-olefin oils (PAO6) were performed in a reciprocating test rig using an alumina ball as the counterpart. From that, only the best AAO condition was selected. Finally, three more lubricant compositions were tested, as follows: adding ZDDP to PAO6, alumina nanoparticles (~100 nm) to PAO6, and ZDDP + nanoparticles. The addition of nano-alumina to the PAO6 resulted in the maintenance of COF values with only PAO6 (~0.1), when the most significant drop in the surface roughness was observed along with the tests. Full article

This paper discusses the fabrication of three-dimensional dendritic Ag nanostructures, showcasing pronounced Localized Surface Plasmon Resonance (LSPR) effects. These nanostructures, employed in surface-enhanced Raman scattering (SERS), function as sensors for lactic acid in artificial sweat. The dendritic structures of the silver nanoparticles (AgNPs) create an effective SERS substrate, with additional hotspots at branch junctures enhancing LSPR. We achieve differential LSPR effects by varying the distribution and spacing of branches and the overall morphology. Adjustments to electrodeposition parameters, such as current and plating solution protective agents on an anodized aluminum oxide (AAO) base, allow for precise control over LSPR intensities. By pre-depositing AgNPs, the electron transmission paths during electrodeposition are modified, which leads to optimized dendritic morphology and enhanced LSPR effects. Parameter optimization produces elongated rods with main and secondary branches, covered with uniformly sized, densely packed, non-overlapping spherical AgNPs. This configuration enhances the LSPR effect by generating additional hotspots beyond the branch tips. Fine-tuning the electrodeposition parameters improved the AgNPs’ morphology, achieving uniform particle distribution and optimal spacing. Compared to non-SERS substrates, our structure amplified the Raman signal for lactic acid detection by five orders of magnitude. This method can effectively tailor SERS substrates for specific analytes and laser-based detection. Full article

Standoff laser absorption spectroscopy (LAS) has attracted considerable interest across many applications for environmental safety. Herein, we propose an anodic aluminum oxide (AAO) microcantilever LAS combined with machine learning (ML) for sensitive and selective standoff discrimination of explosive residues. A nanoporous AAO microcantilever with a thickness of <1 μm was fabricated using a micromachining process; its spring constant (18.95 mN/m) was approximately one-third of that of a typical Si microcantilever (53.41 mN/m) with the same dimensions. The standoff infrared (IR) spectra of pentaerythritol tetranitrate, cyclotrimethylene trinitramine, and trinitrotoluene were measured using our AAO microcantilever LAS over a wide range of wavelengths, and they closely matched the spectra obtained using standard Fourier transform infrared spectroscopy. The standoff IR spectra were fed into ML models, such as kernel extreme learning machines (KELMs), support vector machines (SVMs), random forest (RF), and backpropagation neural networks (BPNNs). Among these four ML models, the kernel-based ML models (KELM and SVM) were found to be efficient learning models able to satisfy both a high prediction accuracy (KELM: 94.4%, SVM: 95.8%) and short hyperparameter optimization time (KELM: 5.9 s, SVM: 7.6 s). Thus, the AAO microcantilever LAS with kernel-based learners could emerge as an efficient sensing method for safety monitoring. Full article

Anodized aluminum oxide (AAO) molds were used for the production of large-area and inexpensive superhydrophobic polymer films. A controlled anodization methodology was developed for the fabrication of hierarchical micro–nanoporous (HMN) AAO imprint molds (HMN-AAO), where phosphoric acid was used as both an electrolyte and a widening agent. Heat generated upon repetitive high-voltage (195 V) anodization steps is effectively dissipated by establishing a cooling channel. On the HMN-AAO, within the hemispherical micropores, arrays of hexagonal nanopores are formed. The diameter and depth of the micro- and nanopores are 18/8 and 0.3/1.25 µm, respectively. The gradual removal of micropatterns during etching in both the vertical and horizontal directions is crucial for fabricating HMN-AAO with a high aspect ratio. HMN-AAO rendered polycarbonate (PC) and polymethyl methacrylate (PMMA) films with respective water contact angles (WCAs) of 153° and 151°, respectively. The increase in the WCA is 80% for PC (85°) and 89% for PMMA (80°). On the PC and PMMA films, mechanically robust arrays of nanopillars are observed within the hemispherical micropillars. The micro–nanopillars on these polymer films are mechanically robust and durable. Regular nanoporous AAO molds resulted in only a hydrophobic polymer film (WCA = 113–118°). Collectively, the phosphoric acid-based controlled anodization strategy can be effectively utilized for the manufacturing of HMN-AAO molds and roll-to-roll production of durable superhydrophobic surfaces. Full article

Pyocyanin is considered a maker of Pseudomonas aeruginosa (P. aeruginosa) infection. Pyocyanin is among the toxins released by the P. aeruginosa bacteria. Therefore, the development of a direct detection of PYO is crucial due to its importance. Among the different optical techniques, the Raman technique showed unique advantages because of its fingerprint data, no sample preparation, and high sensitivity besides its ease of use. Noble metal nanostructures were used to improve the Raman response based on the surface-enhanced Raman scattering (SERS) technique. Anodic metal oxide attracts much interest due to its unique morphology and applications. The porous metal structure provides a large surface area that could be used as a hard template for periodic nanostructure array fabrication. Porous shapes and sizes could be controlled by controlling the anodization parameters, including the anodization voltage, current, temperature, and time, besides the metal purity and the electrolyte type/concentration. The anodization of aluminum foil results in anodic aluminum oxide (AAO) formation with different roughness. Here, we will use the roughness as hotspot centers to enhance the Raman signals. Firstly, a thin film of gold was deposited to develop gold/alumina (Au/AAO) platforms and then applied as SERS-active surfaces. The morphology and roughness of the developed substrates were investigated using scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The Au/AAO substrates were used for monitoring pyocyanin secreted from Pseudomonas aeruginosa microorganisms based on the SERS technique. The results showed that the roughness degree affects the enhancement efficiency of this sensor. The high enhancement was obtained in the case of depositing a 30 nm layer of gold onto the second anodized substrates. The developed sensor showed high sensitivity toward pyocyanin with a limit of detection of 96 nM with a linear response over a dynamic range from 1 µM to 9 µM. Full article

Anodic aluminum oxide (AAO) has been widely applied for the surface protection of electronic component packaging through a pore-sealing process, with the enhanced hardness value reaching around 400 Vickers hardness (HV). However, the traditional AAO fabrication at 0~10 °C for surface protection takes at least 3–6 h for the reaction or other complicated methods used for the pore-sealing process, including boiling-water sealing, oil sealing, or salt-compound sealing. With the increasing development of nanostructured AAO, there is a growing interest in improving hardness without pore sealing, in order to leverage the characteristics of porous AAO and surface protection properties simultaneously. Here, we investigate the effect of voltage on hardness under the same AAO thickness conditions in oxalic acid at room temperature from a normal level of 40 V to a high level of 100 V and found a positive correlation between surface hardness and voltage. The surface hardness values of AAO formed at 100 V reach about 423 HV without pore sealing in 30 min. By employing a hybrid pulse anodization (HPA) method, we are able to prevent the high-voltage burning effect and complete the anodization process at room temperature. The mechanism behind this can be explained by the porosity and photoluminescence (PL) intensity of AAO. For the same thickness of AAO from 40~100 V, increasing the anodizing voltage decreases both the porosity and PL intensity, indicating a reduction in pores, as well as anion and oxygen vacancy defects, due to rapid AAO growth. This reduction in defects in the AAO film leads to an increase in hardness, allowing us to significantly enhance AAO hardness without a pore-sealing process. This offers an effective hardness enhancement in AAO under economically feasible conditions for the application of hard coatings and protective films. Full article